Examples of the show diag and show interface wideband-cable Commands
The following example shows output from the show diag command on a Cisco uBR10012 router with a Cisco 3 Gbps Wideband Shared
Port Adapter installed in slot 1, subslot 0.
Router# show diag 1/0
Slot 1:
4jacket-1 card, 0 ports
Card is full slot size
Card is analyzed
Card detected 01:09:58 ago
Card uptime 0 days, 1 hours, 9 minutes, 57 seconds
Card idle time 0 days, 1 hours, 1 minutes, 53 seconds
Voltage status:
EEPROM contents, slot 1/0:
Controller Type : 1380
Hardware Revision : 1.0
PCB Part Number : 73-10771-02
Board Revision : D0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : CAT1438F01K
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Top Assy. Part Number : 800-27953-03
CLEI Code : IPUIA7TRAA
Product Identifier (PID) : 10000-SIP-600
Version Identifier (VID) : V01
LCMON version, slot 1/0
LCDOS (LATEST-BOOT : DEVELOPMENT BUILD jkotelly-mayflower_lc_0628 /vob/l
cdos/obj-c10k-pq3-lcmon 114)
Built by jkotelly at Mon Jul 16 14:00:18 2007.
Reset reason 0x00000008 (PRE hard reset).
Operational Image version, slot 1/0
LCDOS (C10000 4 SPA Jacket Card Image (Spumoni) : DEVELOPMENT BUILD dasz
hang-license_lc /vob/lcdos/obj-c10k-spumoni 102) major version 1357881885.
Built by daszhang at Thu Jan 10 21:26:42 2013.
SW Version 1.1
Code MD5 D266CF60F88DD7A0408C105F7BA8AB32
FPGA MD5 89C8DD3DCD939BDD43DB19D514416137
Expected Switchover Action: NO INFORMATION
ECC 1 bit errors since last cleared (dd hh mm ss) = 0 (0 days, 0 hours, 0 minutes,
0 seconds)
ECC 1 bit errors while up (total) = 0
Number of crashdumps recorded = 1
SPA Information:
bay 1/0 SPA-UBR10-DS-HD ok
SW Version 1.0
SW Version 1.0
Expected Switchover Action: NO INFORMATION
Product Identifier (PID) : SPA-UBR10-DS-HD
Version Identifier (VID) : V01
PCB Serial Number : CAT1635E0W6
Top Assy. Revision : 02
Hardware Revision : 1.1
CLEI Code :
The Transceiver in slot 1 subslot 0 port 0 is ENABLED.
No Transceiver in slot 1 subslot 0 port 1 .
The Transceiver in slot 1 subslot 0 port 2 is ENABLED.
Wideband Information:
slot/bay 1/0:
SPA-DOCSIS-HD-V1 card, 3 port + 0 redundant port
Card is half slot size
Card is analyzed
Card detected 01:09:57 ago
Card uptime: Not Supported
Card idle time: Not Supported
Voltage status:
VP12V_SPA_MON (+11.909)v VP3P6_MON (+3.595)v
VP2P5_MON (+2.502)v VP1P25_MON (+1.250)v
SPA_AUX_MON (+3.270)v ADM1166_2_OK (+2.048)v
PWR_EN (+2.048)v VP1P0_MON (+1.014)v
VCCINT_MON (+0.999)v ADM1166_2_DOWN (+2.048)v
VP12V_SPA_MON (+11.909)v VP3P3_MON (+3.303)v
VP1P8_MON (+1.802)v VP1P5_MON (+1.497)v
MGTAVTT_MON (+1.197)v MGTAVCC_MON (+0.997)v
VTT_MON (+0.735)v PLL_STATUS (+0.005)v
PLL_LD (+2.048)v ADM1166_2_EN (+2.048)v
License : 0
Licensing Transaction ID : 59040
Ordered PID : SWLIC-SPA-HD-DS-16115360
EEPROM contents, slot/bay 1/0 :
Controller Type : 2938
Hardware Revision : 1.1
Boot Timeout : 500 msecs
PCB Serial Number : CAT1635E0W6
PCB Part Number : 73-15030-01
PCB Revision : 06
Fab Version : 01
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0
Product Identifier (PID) : SPA-UBR10-DS-HD
Version Identifier (VID) : V01
Top Assy. Part Number : 800-38945-01
Top Assy. Revision : 02
IDPROM Format Revision : 36
System Clock Frequency : 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00 00 00 00
CLEI Code :
Base MAC Address : 00 00 00 00 00 00
MAC Address block size : 1
Manufacturing Test Data : 00 00 00 00 00 00 00 00
Field Diagnostics Data : 00 00 00 00 00 00 00 00
Calibration Data : Minimum: 0 dBmV, Maximum: 0 dBmV
Calibration values :
Power Consumption : 300000 mWatts (Maximum)
Environment Monitor Data : 03 30 2E E0 46 32 09 C4
46 32 0C E4 46 32 03 E8
46 1E 03 E8 46 1E 2E E0
46 32 0C E4 46 32 07 08
46 32 05 DC 46 32 04 B0
46 19 03 E8 46 1E 02 EE
46 32 FE 02 EF 64
Processor Label : 00 00 00 00 00 00 00
Platform features : 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
00 00 00 00 00 00 00
Asset ID : P1B-62B
Asset Alias :
The following show interface wideband-cable command displays information about the cable interface for wideband channel 1 on the Cisco 3 Gbps Wideband Shared
Port Adapter located in slot 1, subslot 0.
Router# show interface wideband-cable 1/0/0:1
Wideband-Cable1/0/0:1 is up, line protocol is up
Hardware is Wideband CMTS Cable interface, address is 001a.2f8a.df10 (bia 001a
.2f8a.df10)
MTU 1500 bytes, BW 75000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation MCNS, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Interface Wideband-Cable1/0/0:1 queueing strategy: PXF Class-based
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
...