This section describes how to configure your networking devices to filter traffic, function as a firewall, or detect potential viruses.

Perform this task to control access to a vty on a router by creating an IPv6 ACL to provide access class filtering.

Perform this task to create an IPv6 ACL and configure the IPv6 ACL to pass or block traffic in Cisco IOS Release 12.2(11)T, 12.0(22)S, or earlier releases.

Note

The source-ipv6-prefix argument filters traffic by packet source address, and the destination-ipv6-prefix argument filters traffic by packet destination address. The Cisco IOS software compares an IPv6 prefix against the permit and deny condition statements in the access list. Every IPv6 access list, including access lists that do not have any permit and deny condition statements, has an implicit deny any any statement as its last match condition. The priority or sequence value applied to each condition statement dictates the order in which the statement is applied in the access list. >

Perform this task to apply the IPv6 ACL to an interface in Cisco IOS Release 12.2(11)T, 12.0(22)S, or earlier releases.

Sample Output from the show crypto ipsec sa ipv6 Command

The following is sample output from the show crypto ipsec sa ipv6 command:

Router# show crypto ipsec sa ipv6
interface: Tunnel0
     Crypto map tag: Tunnel0-head-0, local addr 3FFE:2002::A8BB:CCFF:FE01:9002
    protected vrf: (none)
    local  ident (addr/mask/prot/port): (::/0/0/0)
    remote ident (addr/mask/prot/port): (::/0/0/0)
    current_peer 3FFE:2002::A8BB:CCFF:FE01:2C02 port 500
      PERMIT, flags={origin_is_acl,}
     #pkts encaps: 133, #pkts encrypt: 133, #pkts digest: 133
     #pkts decaps: 133, #pkts decrypt: 133, #pkts verify: 133
     #pkts compressed: 0, #pkts decompressed: 0
     #pkts not compressed: 0, #pkts compr. failed: 0
     #pkts not decompressed: 0, #pkts decompress failed: 0
     #send errors 60, #recv errors 0
      local crypto endpt.: 3FFE:2002::A8BB:CCFF:FE01:9002,
      remote crypto endpt.: 3FFE:2002::A8BB:CCFF:FE01:2C02
      path mtu 1514, ip mtu 1514
      current outbound spi: 0x28551D9A(676666778)
      inbound esp sas:
       spi: 0x2104850C(553944332)
         transform: esp-des ,
         in use settings ={Tunnel, }
         conn id: 93, flow_id: SW:93, crypto map: Tunnel0-head-0
         sa timing: remaining key lifetime (k/sec): (4397507/148)
         IV size: 8 bytes
         replay detection support: Y
         Status: ACTIVE
      inbound ah sas:
       spi: 0x967698CB(2524354763)
         transform: ah-sha-hmac ,
         in use settings ={Tunnel, }
         conn id: 93, flow_id: SW:93, crypto map: Tunnel0-head-0
         sa timing: remaining key lifetime (k/sec): (4397507/147)
         replay detection support: Y
         Status: ACTIVE
      inbound pcp sas:
      outbound esp sas:
       spi: 0x28551D9A(676666778)
         transform: esp-des ,
         in use settings ={Tunnel, }
         conn id: 94, flow_id: SW:94, crypto map: Tunnel0-head-0
         sa timing: remaining key lifetime (k/sec): (4397508/147)
         IV size: 8 bytes
         replay detection support: Y
         Status: ACTIVE
      outbound ah sas:
       spi: 0xA83E05B5(2822636981)
         transform: ah-sha-hmac ,
         in use settings ={Tunnel, }
         conn id: 94, flow_id: SW:94, crypto map: Tunnel0-head-0
         sa timing: remaining key lifetime (k/sec): (4397508/147)
         replay detection support: Y
         Status: ACTIVE
      outbound pcp sas:

Sample Output from the show crypto isakmp peer Command

The following sample output shows peer descriptions on an IPv6 router:

Router# show crypto isakmp peer detail
Peer: 2001:DB8:0:1::1 Port: 500 Local: 2001:DB8:0:2::1
Phase1 id: 2001:DB8:0:1::1
flags: 
NAS Port: 0 (Normal)
IKE SAs: 1 IPsec SA bundles: 1
last_locker: 0x141A188, last_last_locker: 0x0
last_unlocker: 0x0, last_last_unlocker: 0x0

Sample Output from the show crypto isakmp profile Command

The following sample output shows the ISAKMP profiles that are defined on an IPv6 router:

Router# show crypto isakmp profile
ISAKMP PROFILE tom
Identities matched are:
ipv6-address 2001:DB8:0:1::1/32 
Certificate maps matched are:
Identity presented is: ipv6-address fqdn
keyring(s): <none>
trustpoint(s): <all>

Sample Output from the show crypto isakmp sa Command

The following sample output shows the SAs of an active IPv6 device. The IPv4 device is inactive:

Router# show crypto isakmp sa detail

Codes: C - IKE configuration mode, D - Dead Peer Detection

        K - Keepalives, N - NAT-traversal

        X - IKE Extended Authentication

        psk - Preshared key, rsig - RSA signature

        renc - RSA encryption

IPv4 Crypto ISAKMP SA

C-id  Local           Remote          I-VRF    Status Encr Hash Auth DH 

Lifetime Cap.

IPv6 Crypto ISAKMP SA

  dst: 3FFE:2002::A8BB:CCFF:FE01:2C02

  src: 3FFE:2002::A8BB:CCFF:FE01:9002

  conn-id: 1001  I-VRF:          Status: ACTIVE Encr: des  Hash: sha  Auth: 

psk

  DH: 1  Lifetime: 23:45:00 Cap: D    Engine-id:Conn-id = SW:1

  dst: 3FFE:2002::A8BB:CCFF:FE01:2C02

  src: 3FFE:2002::A8BB:CCFF:FE01:9002

  conn-id: 1002  I-VRF:          Status: ACTIVE Encr: des  Hash: sha  Auth: 

psk

  DH: 1  Lifetime: 23:45:01 Cap: D    Engine-id:Conn-id = SW:2

Sample Output from the show ipv6 access-list Command

In the following example, the show ipv6 access-listcommand is used to verify that IPv6 ACLs are configured correctly:

Router> show ipv6 access-list
IPv6 access list inbound
    permit tcp any any eq bgp reflect tcptraffic (8 matches) sequence 10
    permit tcp any any eq telnet reflect tcptraffic (15 matches) sequence 20
    permit udp any any reflect udptraffic sequence 30
IPv6 access list tcptraffic (reflexive) (per-user)
    permit tcp host 2001:DB8:1::32 eq bgp host 2001:DB8:2::32 eq 11000 timeout 300 (time         left 243) sequence 1
    permit tcp host 2001:DB8:1::32 eq telnet host 2001:DB8:2::32 eq 11001 timeout 300         (time left 296) sequence 2
IPv6 access list outbound
    evaluate udptraffic
    evaluate tcptraffic

Sample Output from the show ipv6 prefix-list Command

The following example shows the output of the show ipv6 prefix-list command with the detail keyword:

Router# show ipv6 prefix-list detail
Prefix-list with the last deletion/insertion: bgp-in
ipv6 prefix-list 6to4:
   count: 1, range entries: 0, sequences: 5 - 5, refcount: 2
   seq 5 permit 2001:DB8::/32 (hit count: 313, refcount: 1)
ipv6 prefix-list aggregate:
   count: 2, range entries: 2, sequences: 5 - 10, refcount: 30
   seq 5 deny 3FFE:C00::/24 ge 25 (hit count: 568, refcount: 1)
   seq 10 permit ::/0 le 48 (hit count: 31310, refcount: 1)
ipv6 prefix-list bgp-in:
   count: 6, range entries: 3, sequences: 5 - 30, refcount: 31
   seq 5 deny 5F00::/8 le 128 (hit count: 0, refcount: 1)
   seq 10 deny ::/0 (hit count: 0, refcount: 1)
   seq 15 deny ::/1 (hit count: 0, refcount: 1)
   seq 20 deny ::/2 (hit count: 0, refcount: 1)
   seq 25 deny ::/3 ge 4 (hit count: 0, refcount: 1)
   seq 30 permit ::/0 le 128 (hit count: 240664, refcount: 0) 

Sample Output from the show ipv6 virtual-reassembly Command

The following example shows the output of the show ipv6 virtual-reassemblycommand with the interfacekeyword:

Router# show ipv6 virtual-reassembly interface e1/1
Configuration Information:
---------------------------------
Virtual Fragment Reassembly (VFR) is ENABLED...
Maximum number of datagram that can be reassembled at a time: 64
Maximum number of fragments per datagram: 8
Timeout value of a datagram: 3 seconds
Statistical Information:
----------------------------
Number of datagram being reassembled:12
Number of fragments being processed:48
Total number of datagram reassembled:6950
Total number of datagram failed: 9

Sample Output from the show logging Command

In the following example, the show loggingcommand is used to display logging entries that match the first line (sequence 10) of the access list named list1:

Router> show logging
00:00:36: %IPV6-6-ACCESSLOGP: list list1/10 permitted tcp 2001:DB8:1::1(11001) (Ethernet0/0) -> 2001:DB8:1::2(179), 1 packet

Sample Output from the clear ipv6 access-list Command

In the following example, the show ipv6 access-listcommand is used to display some match counters for the access list named list1. The clear ipv6 access-listcommand is issued to reset the match counters for the access list named list1. The show ipv6 access-listcommand is used again to show that the match counters have been reset.

Router> show ipv6 access-list list1
IPv6 access list list1
    permit tcp any any log-input (6 matches) sequence 10
    permit icmp any any echo-request log-input sequence 20
    permit icmp any any echo-reply log-input sequence 30
Router# clear ipv6 access-list list1
Router# show ipv6 access-list list1
IPv6 access list list1
    permit tcp any any log-input sequence 10
    permit icmp any any echo-request log-input sequence 20
    permit icmp any any echo-reply log-input sequence 30

This example configures two IPv6 ACLs named OUTBOUND and INBOUND and applies both ACLs to outbound and inbound traffic on Ethernet interface 0. The first and second permit entries in the OUTBOUND list permit all TCP and User Datagram Protocol (UDP) packets from network 2001:DB8:0300:0201::/32 to exit out of Ethernet interface 0. The entries also configure the temporary IPv6 reflexive ACL named REFLECTOUT to filter returning (incoming) TCP and UDP packets on Ethernet interface 0. The first deny entry in the OUTBOUND list keeps all packets from the network fec0:0:0:0201::/64 (packets that have the site-local prefix fec0:0:0:0201 as the first 64 bits of their source IPv6 address) from exiting out of Ethernet interface 0.

The evaluate command in the INBOUND list applies the temporary IPv6 reflexive ACL named REFLECTOUT to inbound TCP and UDP packets on Ethernet interface 0. When outgoing TCP or UDP packets are permitted on Ethernet interface 0 by the OUTBOUND list, the INBOUND list uses the REFLECTOUT list to match (evaluate) the returning (incoming) TCP and UDP packets.

ipv6 access-list OUTBOUND
 permit tcp 2001:DB8:0300:0201::/32 any reflect REFLECTOUT
 permit udp 2001:DB8:0300:0201::/32 any reflect REFLECTOUT
 deny fec0:0:0:0201::/64 any
ipv6 access-list INBOUND
 evaluate REFLECTOUT
interface ethernet 0
 ipv6 traffic-filter OUTBOUND out
 ipv6 traffic-filter INBOUND in

Note

Given that a permit any any statement is not included as the last entry in the OUTBOUND or INBOUND ACL, only TCP and UDP packets matching the configured permit entries in the ACL and ICMP packets matching the implicit permit conditions in the ACL are permitted out of and in to Ethernet interface 0 (the implicit deny all condition at the end of the ACL denies all other packet types on the interface).

The example configures HTTP access to be restricted to certain hours during the day, and to log any activity outside of the permitted hours:

time-range lunchtime
 periodic weekdays 12:00 to 13:00
ipv6 access-list OUTBOUND
 permit tcp any any eq www time-range lunchtime
 deny tcp any any eq www log-input
 permit tcp 2001:DB8::/32 any
 permit udp 2001:DB8::/32 any

The following example is from a router running Cisco IOS Release 12.2(11)T, 12.0(22)S, or earlier releases.

The example configures the IPv6 ACL named list2 and applies the ACL to outbound traffic on Ethernet interface 0. Specifically, the first ACL entry keeps all packets from the network fec0:0:0:2::/64 (packets that have the site-local prefix fec0:0:0:2 as the first 64 bits of their source IPv6 address) from exiting out of Ethernet interface 0. The second entry in the ACL permits all other traffic to exit out of Ethernet interface 0. The second entry is necessary because an implicit deny all condition is at the end of each IPv6 ACL.

ipv6 access-list list2 deny fec0:0:0:2::/64 any
ipv6 access-list list2 permit any any
interface ethernet 0
 ipv6 traffic-filter list2 out

If the same configuration was used on a router running Cisco IOS Release 12.2(13)T, 12.0(23)S, or later releases, the configuration would be translated into IPv6 access list configuration mode as follows:

ipv6 access-list list2 
 deny ipv6 fec0:0:0:2::/64 any
 permit ipv6 any any
interface ethernet 0
 ipv6 traffic-filter list2 out

Note	IPv6 is automatically configured as the protocol type in permit any any and deny any any statements that are translated from global configuration mode to IPv6 access list configuration mode.