- About this Guide
- Chapter 1, Install the Shelf and Common Control Cards
- Chapter 2, Connect the PC and Log Into the GUI
- Chapter 3, Turn Up a Node
- Chapter 4, Perform Node Acceptance Tests
- Chapter 5, Provision Transponder and Muxponder Cards
- Chapter 6, Turn Up a Network
- Chapter 7, Create Channels and Circuits
- Chapter 8, Manage Alarms
- Chapter 9, Monitor Performance
- Chapter 10, Manage the Node
- Chapter 11, Change DWDM Card Settings
- Chapter 12, Add and Remove Cards and Nodes
- Chapter 13, Maintain the Node
- Chapter 14, Power Down the Node
- Appendix A, CTC Information and Shortcuts
- Before You Begin
- NTP-G151 Create and Delete Optical Channel Client Connections
- NTP-G59 Create and Delete Optical Channel Network Connections
- NTP-G150 Upgrade Optical Channel Network Connections to Optical Channel Client Connections
- NTP-G60 Create and Delete Overhead Circuits
- NTP-G62 Create a J0 Section Trace
- NTP-G58 Locate and View Optical Channel Network and Client Connections
Create Channels and Circuits
This chapter explains how to create Cisco ONS 15454 dense wavelength division multiplexing (DWDM) optical channel client connections (OCHCCs), optical channel client network connections (OCHNCs), and overhead circuits. It also tells you how to upgrade OCHNCs to OCHCCs.
Note 
Unless otherwise specified, "ONS 15454" refers to both ANSI and ETSI shelf assemblies.
Before You Begin
Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 DWDM Troubleshooting Guide as necessary.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1. G151 Create and Delete Optical Channel Client Connections—Complete as needed.
2. G59 Create and Delete Optical Channel Network Connections—Complete as needed.
3. G150 Upgrade Optical Channel Network Connections to Optical Channel Client Connections—Complete as needed.
4. G60 Create and Delete Overhead Circuits—Complete as needed to create IP-encapsulated, firewall, and proxy tunnels, to create generic communications channel (GCC) terminations, to provision orderwire, or to create user data channel (UDC) circuits.
5. G62 Create a J0 Section Trace—Complete as needed to monitor interruptions or changes to traffic between two nodes.
6. G58 Locate and View Optical Channel Network and Client Connections—Complete as needed to find, view, and filter OCHCCs and OCHNCs.
NTP-G151 Create and Delete Optical Channel Client Connections
Step 1 As needed, identify the OCHCC to be provisioned using the "DLP-G350 Use the Cisco MetroPlanner Traffic Matrix Report" task.
Step 2 Complete the "DLP-G46 Log into CTC" task at a node on the network where you want to create and delete OCHCCs. If you are already logged in, continue with Step 3.
Step 3 If you want to assign a name to the OCHCC source and destination ports before you create the circuit, complete the "DLP-G104 Assign a Name to a Port" task. (Naming the client ports facilitates the OCHCC creation by helping you more quickly identify the correct client ports.) If not, continue with Step 4.
Step 4 If the client TXP/MXP/line cards are installed in a multishelf, continue with Step 5. If not, complete the following steps:
a. Use the information obtained from the Cisco MetroPlanner traffic matrix report in Step 1 to complete the "DLP-G344 Verify Provisionable Patchcords" task. If PPCs are created between the nodes containing the TXP/MXP/ITU-T line cards and the DWDM nodes at each end of the OCHCC, continue with Step 5, If not, continue with Step b.
b. complete the "DLP-G99 Create a Provisionable Patchcord" task to create the PPCs between the OCHCC source and destination nodes.
Step 5 If the client TXP/MXP/ITU-T line card is installed in a multishelf, use the information obtained from the Cisco MetroPlanner traffic matrix report in Step 1 to create internal patchcords between the 32DMX or 32DMX-O ports and the TXP/MXP trunk ports using the "DLP-G354 Create an Internal Patchcord Manually" task. Create the internal patchcords on both the source and destination nodes of each OCHCC path. If the TXP/MXP/ITU-T line card is not installed in a multishelf, continue with Step 6.
Step 6 Complete the "DLP-G345 Verify OCHCC Client Ports" task.
Step 7 Complete the "DLP-G346 Provision Optical Channel Client Connections" task as needed.
Step 8 Complete the "DLP-G347 Delete Optical Channel Client Connections" task as needed.
Stop. You have completed this procedure.
DLP-G104 Assign a Name to a Port
Step 1 Double-click the card that has the port that you want to provision. This can be any port on a traffic-carrying card.
Step 2 Click the Provisioning tab.
Step 3 Double-click the Port Name table cell for the port number to which you are assigning a name. The cell activates and a blinking cursor appears to indicate where you are to type the port name.
Step 4 Type the port name.
The port name can be up to 32 alphanumeric/special characters. The field is blank by default.
Step 5 Click Apply.
Step 6 Return to your originating procedure (NTP).
DLP-G345 Verify OCHCC Client Ports
Purpose |
This task verifies the OCHCC client ports. |
Tools/Equipment |
|
Prerequisite Procedures |
|
Required/As Needed |
As needed |
Onsite/Remote |
Onsite |
Security Level |
Provisioning or higher |
Step 1 Display the TXP, MXP, or ITU-T line card in card view.
Step 2 Click the Provisioning > Maintenance tabs.
Step 3 Verify that the administrative state of the client and trunk ports is Out of Service and Disabled (OOS,DSBLD) (ANSI) or Locked,disabled (ETSI). If so, continue with Step 4. If not, complete the following steps:
a. Click the Admin State table cell and choose OOS,DSBLD (ANSI) or Locked,disabled (ETSI) for the client and trunk ports.
b. Click Apply.
Step 4 Click the Provisioning > Pluggable Port Modules tabs.
Step 5 Verify that a pluggable port module has been created and that the port rate under the Pluggable Port area is provisioned. If so, continue with Step 7. If not, complete the "DLP-G277 Provision a Multirate PPM" task and the "DLP-G278 Provision the Optical Line Rate" task.
Step 6 Repeat Steps 1 through 5 for each TXP, MXP, or ITU-T line card containing OCHCC ports that you want to verify.
Step 7 Return to your originating procedure (NTP).
DLP-G346 Provision Optical Channel Client Connections
Note OCHCCs can be created on preprovisioned client cards or physically installed client cards.
Note OCHCC creation will fail if the client card's trunk port is in service and the trunk port parameters provisioned on the OCHCC circuit creation wizard differ from the settings provisioned on the client card's trunk port. If you want the OCHCC circuit to provision the client card trunk port's ITU-T G.709, FEC, SD and SF threshold settings and Mapping parameters, you must place the client card trunk ports out of service.
Note Creating an OCHCC circuit automatically creates an OCH trail circuit between the OCHCC source and destination client card trunk ports. The OCH trail circuit is created for the first OCHCC between two MXP cards. The OCH trail circuit is used by succeeding OCHCCs created between the MXP cards. When the OCH trail is created, it is assigned a system-generated name in the format circuit-type_NE-name::unique sequence number. To edit the OCH trail circuit name, complete the "DLP-G425 Edit an OCH Trail Circuit Name" task.
Note If trunk ports are connected by a peer-to-peer provisionable patchcord (PPC), an OCH trail is not created.
Note The OCH Wlen (wavelength) parameter on the Circuits page can be used to determine the OCHCC and OCH trail associations.
Step 1 From the View menu, choose Go to Network View.
Step 2 Click the Circuits tab, then click Create.
Step 3 In the Circuit Creation dialog box, choose OCHCC from the Circuit Type list.
Step 4 Click Next.
Step 5 In the Circuit area of the Circuit Attributes page (Figure 7-1), provision the OCHCC circuit attributes:
•Name—Assign a name to the OCHCC. The name can be alphanumeric and up to 48 characters (including spaces). Circuit names should be 44 characters or less if you want the ability to create monitor circuits. If you leave the field blank, CTC assigns a default name to the circuit.
•Type—(Display only) OCHCC.
•Size—Defines the circuit payload type and rate. Two fields are provided. The first specifies the payload type. Choose a payload type, then choose the rate in the next field. Table 7-1 provides the OCHCC payload types and rates.
Note The payload type and rate must match the PPM provisioning on the client cards at the source and destination nodes.
•OCHNC Wavelength—Provides three fields to define the wavelength that the OCHCC will use to travel across the OCH network. Choose a wavelength from the first field. In the second field, you can change the wavelength band by choosing either C Band or L Band. In the third field, you can indicate whether odd or even C-band or L-band wavelengths are displayed.
Note The OCHNC wavelength must match the trunk wavelength provisioned on the source and destination TXP or MXP cards. If the wavelengths do not match, the card will not appear as a source or destination.
•Bidirectional—(Display only) OCHCCs are bidirectional. This field cannot be changed.
Figure 7-1 OCHCC Attributes Page
Step 6 In the State area of the Circuit Attributes page, provision the OCHCC state attributes:
•State—Provisions the OCHCC circuit state. The state can be IS (ANSI)/Unlocked (ETSI) or OOS,DSBLED (ANSI)/Locked,Disabled (ETSI).
•Apply to OCHCC ports—If checked, applies the state chosen in the Apply to OCHCC ports drop-down list to the OCHCC client ports. For TXP, MXP, TXPP, or MXPP cards, this will be the client and all trunk ports. For ITU-T-compliant OC line cards, this will be the trunk port only. The states that you can apply include: IS (ANSI)/Unlocked (ETSI), OOS,DSBLED (ANSI)/Locked,Disabled (ETSI), and IS,AINS (ANSI)/Unlocked,AutomaticInService (ETSI).
Step 7 In the Protection area of the Circuit Attributes page, provision the OCHCC protection attributes:
•Protection—Check this box if the source and destination client cards are TXPP or MXPP cards. Checking the box restricts the source and destination choices to those cards and allows you to provision the reversion parameters.
•Reversion—If Protection is checked, checking this box turns on the TXPP or MXPP reversion parameter.
•Reversion Time—If Reversion is checked, set the time before the protection will switch to the active port after conditions that caused the switch are remedied.
Step 8 In the Trunk area of the Circuit Attributes page, provision the OCHCC trunk attributes:
Note For information about the trunk fields supported by the TXP, MXP, or ITU-T line card, refer to the Chapter 11 "Change DWDM Card Settings," and to the "Card Reference" chapter in the ONS 15454 DWDM Reference Manual.
•G.709 OTN—If checked, enables the ITU-T G.709 optical transport network on the client cards, if permitted by the client card and payload.
•FEC—Allows you to enable or disable FEC on the client cards, if permitted by the client card and payload.
•SF BER—Allows you to set the signal fail bit error rate for payloads and client cards that allow the parameter to be provisioned.
•SD BER—Allows you to set the signal degrade bit error rate for payloads and client cards that allow the parameter to be provisioned.
•Mapping—Sets the mapping for the TXP_MR_10E, TXP_MR_10E_C, TXP_MR_10E_L, MXP_MR_10DME_C, and MXP_MR_DME_L cards. If you set mapping to Synchronous, the client signal is mapped into the OTU2 signal without justification of the payload because the client signal timing (the timing source) is the same as the trunk output timing. If you set mapping to asynchronous, the trunk timing is disconnected from the client timing (because the network element [NE] is the timing source), so justification is needed to map the client signal (OC192/STM64) to OTU2 trunk output.
Step 9 Click Next.
Step 10 In the Source area, choose the source node from the Node drop-down list, then choose the source shelf (multishelf nodes only) slot and, if needed, source port from the Shelf, Slot and Port drop-down lists.
If no nodes appear in the Node drop-down list, complete the following steps:
a. Click Back and review your circuit attribute settings. Verify that they are set to the client attributes provisioned on the client cards. If necessary, click Cancel and complete the "DLP-G345 Verify OCHCC Client Ports" task to verify the client settings.
b. If the source and/or destination nodes are not configured for multishelf, complete the "DLP-G344 Verify Provisionable Patchcords" task to verify the patchcords were created accurately.
If these steps do not solve the problem, refer to your next level of support.
Step 11 Click Next.
Step 12 In the Destination area, choose the destination node from the Node drop-down list, then choose the destination shelf (multishelf nodes only), slot and, if needed, source port from the Shelf, Slot and Port drop-down lists.
If no nodes appear in the Node drop-down list, complete the following steps:
a. Click Back and review your circuit attribute settings. Verify that they are set to the client attributes provisioned on the client cards. If necessary, click Cancel and complete the "DLP-G345 Verify OCHCC Client Ports" task to verify the client settings.
b. If the source and/or destination nodes are not configured for multishelf, complete the "DLP-G344 Verify Provisionable Patchcords" task to verify the patchcords were created accurately.
If these steps do not solve the problem, refer to your next level of support.
Step 13 Click Finish. The OCHCC and it OCH trail will appear in the Circuits window. After the circuit status has been verified, the DISCOVERED status appears in the Status column.
If the OCHCC status does not change to DISCOVERED within a 2-3 minutes, refer to the ONS 15454 DWDM Troubleshooting Guide for troubleshooting procedures.
Step 14 Return to your originating procedure (NTP).
DLP-G347 Delete Optical Channel Client Connections
Purpose |
This task deletes DWDM OCHCC circuits. |
Tools/Equipment |
None |
Prerequisite Procedures |
|
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Note If you are deleting more than half of all the active OCHCCs, Cisco recommends that you delete them two at a time to allow for proper power compensation. This does not apply if you are deleting all the active OCHCCs.
Step 1 Complete the "NTP-G103 Back Up the Database" procedure, or record the circuit information if it will be recreated.
Step 2 Consult your network operations center (NOC) or other appropriate personnel to verify that the OCHCC can be safely deleted.
Step 3 Investigate all network alarms and resolve any problems that might be affected by the OCHCC deletion.
Step 4 Choose View > Go to Network View.
Step 5 Click the Circuits tab.
Step 6 Choose one or more OCHCCs, identified under the Type column, that you want to delete, then click Delete.
Step 7 In the Delete Circuits confirmation dialog box, complete the following:
•Change drop port admin state—check this box if you want to change the circuit source and destination ports administrative state. After checking the box, choose one of the following administrative states:
–IS (ANSI) or Unlocked (ETSI—puts the ports in service.
–IS,AINS (ANSI) or UnlockedAutomaticInService (ETSI)—puts the ports in automatic in service.
–OOS,DSBLD (ANSI) or Locked,disabled (ETSI)—removes the ports from service and disables them.
–OOS,MT (ANSI) or Locked,maintenance (ETSI)—removes the ports from service for maintenance.
•Notify when completed—If checked, the CTC Alerts confirmation dialog box indicates when the OCHCC is deleted. During this time, you cannot perform other CTC functions. If you are deleting many OCHCCs, waiting for confirmation might take a few minutes. Circuits are deleted whether or not this check box is checked.
Note The CTC Alerts dialog box will not automatically open to show a deletion error unless you checked All alerts or Error alerts only in the CTC Alerts dialog box. For more information, see the "DLP-G53 Configure the CTC Alerts Dialog Box for Automatic Popup" task. If the CTC Alerts dialog box is not set to open automatically with a notification, the red triangle inside the CTC Alerts toolbar icon indicates that a notification exists.
Step 8 Complete one of the following:
•If you checked Notify when completed, the CTC Alerts dialog box appears. If you want to save the information, continue with Step 10. If you do not want to save the information, continue with Step 11.
•If you did not check Notify when completed, the Circuits window appears. Continue with Step 12.
Step 9 If you want to save the information in the CTC Alerts dialog box, complete the following steps. If you do not want to save it, continue with Step 11.
a. Click Save.
b. Click Browse and navigate to the directory where you want to save the file.
c. Type the file name using a.txt file extension, and click OK.
Step 10 Click Close to close the CTC Alerts dialog box.
Step 11 Complete the "NTP-G103 Back Up the Database" procedure if you require a backup of your changes.
Step 12 Return to your originating procedure (NTP).
DLP-G424 Edit an OCHCC Circuit Name
Purpose |
This task changes the name of an OCHCC circuit. |
Tools/Equipment |
None |
Prerequisite Procedures |
G105 Provision Optical Channel Network Connections |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Step 1 From the View menu, choose Go to Network View.
Step 2 Click the Circuits tab.
Step 3 Click the OCHCC whose name you want to edit, then click Edit. The Edit Circuit dialog box appears with the General tab displayed.
Step 4 In the Name field, enter the new OCHCC circuit name.
Step 5 Click Apply.
Step 6 Return to your originating procedure (NTP).
DLP-G425 Edit an OCH Trail Circuit Name
Purpose |
This task changes the name of an OCH trail circuit. |
Tools/Equipment |
None |
Prerequisite Procedures |
G105 Provision Optical Channel Network Connections |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Step 1 From the View menu, choose Go to Network View.
Step 2 Click the Circuits tab.
Step 3 Click the OCH trail whose name you want to edit, then click Edit. The Edit Circuit dialog box appears with the General tab displayed.
Step 4 In the Name field, enter the new OCH trail circuit name.
Step 5 Click Apply.
Step 6 Return to your originating procedure (NTP).
NTP-G59 Create and Delete Optical Channel Network Connections
Step 1 Complete the "DLP-G46 Log into CTC" task at a node on the network where you want to create and delete OCHNCs. If you are already logged in, continue with Step 2.
Step 2 If you want to assign a name to the OCHNC source and destination ports before you create the circuit, complete the "DLP-G104 Assign a Name to a Port" task. If not, continue with the next step.
Step 3 Complete the "DLP-G105 Provision Optical Channel Network Connections" task as needed.
Step 4 Complete the "DLP-G106 Delete Optical Channel Network Connections" task as needed.
Step 5 Complete the "DLP-G426 Edit an OCHNC Circuit Name" task, as needed.
Stop. You have completed this procedure.
DLP-G105 Provision Optical Channel Network Connections
Step 1 Choose View > Go to Network View.
Step 2 Click the Circuits tab, then click Create.
Step 3 In the Circuit Creation dialog box, choose OCHNC from the Circuit Type list.
Step 4 Click Next.
Step 5 In the Circuit area of the Circuit Attributes, provision the OCHNC circuit attributes:
•Name—Assign a name to the OCHNC. The name can be alphanumeric and up to 48 characters (including spaces). Circuit names should be 44 characters or less if you want the ability to create monitor circuits. If you leave the field blank, CTC assigns a default name to the circuit.
•Type—(Display only) OCHNC.
•Size—Equipped non specific is the default. You cannot change it.
•OCHNC Wavelength—Choose a band, either C Band or L Band in the lower drop-down list, then choose wavelength you want to provision in the upper drop-down list. Table 7-2 lists the thirty-two available wavelengths.
•Use OCHNC Direction—Choose the OCHNC direction, either East to West or West to East. If you choose West to East, the channel will exit the node through the LINE-TX port of the east OSC-CSM, OPT-BST, or OPT-BST-E card, named the East Side Card by Cisco MetroPlanner (typically, these cards are hosted by Slot 17). If you choose East to West, the channel will exit the node through the LINE-TX port of the west OSC-CSM, OPT-BST, or OPT-BST-E card, named the West Side Card by Cisco MetroPlanner (typically, these cards are hosted by Slot 1).
Note OCHNC direction is not used in Software Release 7.0.
•Bidirectional—Check this check box to create a bidirectional OCHNC; uncheck it to create a unidirectional OCHNC.
•State—Provisions the OCHNC circuit state. The state can be IS (ANSI)/Unlocked (ETSI) or OOS,DSBLED (ANSI)/Locked,Disabled (ETSI).
Step 6 Click Next.
Step 7 In the Circuit Source area, choose the source node from the Node drop-down list, then choose the source shelf (multishelf only), slot, and, if needed source port from the Shelf, Slot, and Port drop-down lists.
The source In and Out shelf (multishelf only), slot and port appear under the OTS (optical transport signal) Lines area to show the OTS in and out shelf, slot, and ports.
Step 8 Click Next.
Step 9 In the Circuit Destination area, choose the destination node from the Node drop-down list, then choose the destination shelf (multishelf only), slot, and, if needed destination port from the Shelf, Slot, and Port drop-down lists.
The destination In and Out shelf (multishelf only), slot and port appear under the OTS (optical transport signal) Lines area to show the destination in and out shelf, slots, and ports.
Step 10 Click Finish. After the circuit status has been verified, the DISCOVERED status appears in the Status column. (The circuit might take a few minutes to come up, depending on the size of the network.) If problems occur, refer to the Cisco ONS 15454 DWDM Troubleshooting Guide as necessary.
Step 11 Return to your originating procedure (NTP).
DLP-G106 Delete Optical Channel Network Connections
Purpose |
This task deletes DWDM OCHNC circuits. |
Tools/Equipment |
None |
Prerequisite Procedures |
|
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Note If you are deleting more than half of all the active OCHNCs, Cisco recommends that you delete them two at a time to allow for proper power compensation. This does not apply if you are deleting all the active OCHNCs.
Step 1 Complete the "NTP-G103 Back Up the Database" procedure, or record the circuit information if it will be recreated.
Step 2 Consult your NOC or other appropriate personnel to verify that the OCHNC can be safely deleted.
Step 3 Investigate all network alarms and resolve any problems that might be affected by the OCHNC deletion.
Step 4 Choose View > Go to Network View.
Step 5 Click the Circuits tab.
Step 6 On the Circuits table, use the Circuit Name and Type columns to click the OCHNCs that you want to delete. (To choose more than one OCHNC, press the Shift key as you click the circuits.)
Step 7 Click Delete.
Step 8 In the Delete Circuits confirmation dialog box, check Notify when completed, as needed.
If checked, the CTC Alerts confirmation dialog box indicates when the OCHNC is deleted. During this time, you cannot perform other CTC functions. If you are deleting many OCHNCs, waiting for confirmation might take a few minutes. Circuits are deleted whether or not this check box is checked.
Note The CTC Alerts dialog box will not automatically open to show a deletion error unless you checked All alerts or Error alerts only in the CTC Alerts dialog box. For more information, see the "DLP-G53 Configure the CTC Alerts Dialog Box for Automatic Popup" task. If the CTC Alerts dialog box is not set to open automatically with a notification, the red triangle inside the CTC Alerts toolbar icon indicates that a notification exists.
Step 9 Complete one of the following:
•If you checked Notify when completed, the CTC Alerts dialog box appears. If you want to save the information, continue with Step 10. If you do not want to save the information, continue with Step 11.
•If you did not check Notify when completed, the Circuits window appears. Continue with Step 12.
Step 10 If you want to save the information in the CTC Alerts dialog box, complete the following steps. If you do not want to save it, continue with Step 11.
a. Click Save.
b. Click Browse and navigate to the directory where you want to save the file.
c. Type the file name using a.txt file extension, and click OK.
Step 11 Click Close to close the CTC Alerts dialog box.
Step 12 Complete the "NTP-G103 Back Up the Database" procedure if you require a backup of your changes.
Step 13 Return to your originating procedure (NTP).
DLP-G426 Edit an OCHNC Circuit Name
Purpose |
This task changes the name of an OCHNC circuit. |
Tools/Equipment |
None |
Prerequisite Procedures |
G105 Provision Optical Channel Network Connections |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Step 1 From the View menu, choose Go to Network View.
Step 2 Click the Circuits tab.
Step 3 Click the OCHNC whose name you want to edit, then click Edit. The Edit Circuit dialog box appears with the General tab displayed.
Step 4 In the Name field, enter the new OCHNC circuit name.
Step 5 Click Apply.
Step 6 Return to your originating procedure (NTP).
NTP-G150 Upgrade Optical Channel Network Connections to Optical Channel Client Connections
Note During this procedure, the OCHNC is replaced with two circuit types, the OCHCC, which establishes a connection between the client card client ports, and the OCH trail, which establishes a connection between the client card trunk ports. The OCH trail is given the same name as the OCHNC. The OCHCC is given a system-generated name in the format: circuit-type_NE-name::unique sequence number. To edit the OCHCC circuit name, complete the "DLP-G424 Edit an OCHCC Circuit Name" task. To edit the OCH trail circuit name, complete the "DLP-G424 Edit an OCHCC Circuit Name" task.
Note Multiple OCHCCs might use the same OCH trail. The OCH Wlen (wavelength) parameter on the Circuits page can be used to determine the OCHCC and OCH trail associations.
Step 1 As needed, identify the OCHCC to be provisioned using the "DLP-G350 Use the Cisco MetroPlanner Traffic Matrix Report" task.
Step 2 Complete the G46 Log into CTC at a node on the network where you want to upgrade the OCHNCs. If you are already logged in, continue with Step 3.
Step 3 From the View menu, choose Go to Network View.
Step 4 Click the Circuits tab and find the OCH you want to upgrade.
Step 5 Record the following information:
•OCHNC Wlen (OCHNC wavelength)
•Source node/shelf (if applicable)/slot/port/side (include both Side A and Side B nodes, if present)
•Destination node/shelf (if applicable)/slot/port/side (include both Side A and Side B nodes, if present)
Step 6 Use the information recorded in Step 5 to complete one of the following
•G344 Verify Provisionable Patchcords—Complete this task if provisionable patchcords (PPCs) and internal patchcords exist on the network but you are not sure whether one was created for the OCHNC that you want to upgrade.
•G99 Create a Provisionable Patchcord—Complete this procedure if you know that PPCs were not created between the OCHNC node and the client node. If you recently upgraded from a previous release, you must create PPCs between the source client and OCHNC node and between the destination client and OCHNC node.
Step 7 In network view, click the OCHNC that you want to upgrade.
Step 8 From the Tools menu, choose Circuits > Upgrade OCHNC. If the Upgrade OCHNC Initialization "Completed" status appears (Figure 7-2), continue with Step 9. If the "Failed" status appears (Figure 7-3), complete the following substeps:
a. Click each failure reason to view the failure details. A common cause of initialization failures is the absence or incorrect completion of PPCs or internal patchcords between the client nodes and the optical channel (OCH) nodes.
b. Repeat Steps 3 through 8, verifying that the OCHNC ports and provisionable patchcord (PPC) path match on both sides. If the upgrade "Failed" status appears again, click Save to save the results to a local or network computer. (The file can be opened with any text editor.) Then, contact your next level of support.
Figure 7-2 Upgrade OCHNC Initialization—Completed
Figure 7-3 Upgrade OCHNC Initialization—Failed
Step 9 Click each result to review the details. If you want to save the results, click Save and save the results to a file on a local or network computer. Click Continue.
Step 10 Review the information in the Upgrade OCHNC dialog box (Figure 7-4), then click OK.
Step 11 Click Yes in the confirmation dialog box, then click OK on the Completed Upgrade OCHNC wizard page.
Tip To see all of the information in the Source and Destination table cells, increase the column widths by clicking and dragging the column heading borders to the right or left.
Figure 7-4 Upgrade OCHNC Dialog Box
Step 12 View the OCHCC and its OCH trail in the Circuits page. For information and procedures for viewing and editing OCHCC and OCH trails, see the "NTP-G58 Locate and View Optical Channel Network and Client Connections" procedure.
Stop. You have completed this procedure.
DLP-G344 Verify Provisionable Patchcords
Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), Click the Provisioning > Provisionable Patchcords (PPC) tabs.
Step 2 Use one of the following methods to verify that PPCs exist from the client TXP/MXP/line card node, slot, and port to the DWDM OCH node, slot, port, and wavelength:
•Review the Patchcord Terminations table. PPCs should exist from the client TXP/MXP/line card node to the OCH node slot and port recorded in the referring procedure.
•Review the network graphic (see Figure 7-5). PPCs are indicated by a small hand holding a lambda symbol. Clicking the PPC line on the graphic displays the PPC source and destination nodes, slots, and ports in the CTC information area. The information in the information area should match the node, slot, and port recorded in the referring procedure.
Figure 7-5 Viewing the Provisionable Patchcords Table
Step 3 Return to your originating procedure (NTP).
DLP-G99 Create a Provisionable Patchcord
Note This task requires DCC or GCC connectivity between the OCH node and the subtended TXP, MXP, or line card client shelves.
Note An optical port requires two patchcords when the remote end is Y-cable protected or is an add/drop multiplexer or multiplexer/demultiplexer port.
Step 1 Complete the following tasks, as needed, to verify the cabling between the TXP/MXP/line cards in the client node and the OCH cards in the DWDM node:
•G349 Use the Cisco MetroPlanner Internal Connections Report
•G350 Use the Cisco MetroPlanner Traffic Matrix Report
Step 2 In node view (single-node view) or multishelf view (multishelf mode), click the Provisioning > Comm Channels > PPC tabs. If you are in network view, click the Provisioning > PPC tabs.
Step 3 Click Create. The Provisionable Patchcord dialog box appears.
Step 4 In the Origination Node area, choose the origination node. If you are in node view (single-shelf mode) or multishelf view (multishelf mode), the origination node defaults to the current node. If you are in network view, click the desired origination node from the drop-down list.
Step 5 In the Termination Node area, click the desired termination node from the drop-down list. If the remote node has not previously been discovered by CTC but is accessible by CTC, type the name of the remote node.
After you enter a termination node, the dialog box expands so that the TX and RX ports appear (Figure 7-6) for both the origination and termination nodes.
Figure 7-6 Create Provisionable Patchcord - Single Shelf to Single Shelf
Step 6 Type a patchcord identifier (0 through 32767) in the TX and RX ID fields for the origination node and the termination node. The identifiers are used for your internal tracking and to help identify PPCs. All TX and RX IDs must be unique.
Step 7 In the Origination Node area, click the desired origination slot/port from the list of available slots/ports. The origination ports and termination ports must be different. The TX and RX port selections will align automatically, depending on the card. For example, if you choose a TXP card in Slot 5 for the RX port, the TX will automatically change to Slot 5.
Step 8 In the Termination Node area, click the desired termination slot/port from the list of available slots/ports. The origination ports and the termination ports must be different.
Step 9 If you need to provision transmit (Tx) and receive (Rx) separately for multiplexer/demultiplexer cards, check the Separate Tx/Rx check box. If not, continue with Step 10.
Step 10 Click OK.
Step 11 If you provisioned a patchcord on a port in a 1+1 protection group, a dialog box appears to ask if you would like to provision the peer patchcord. Click Yes. Repeat Steps 4 through 10.
Step 12 Return to your originating procedure.
NTP-G60 Create and Delete Overhead Circuits
Note The DCCs, GCCs, and OSCs should not be provisioned between SONET (ANSI) and SDH (ETSI) nodes using CTC or TL1 because they cannot operate between SONET and SDH nodes. These communication channels should be provisioned on similar nodes, such as SONET-to-SONET or SDH-to-SDH.
Step 1 Complete the "DLP-G46 Log into CTC" task at the node where you will create the overhead circuit. If you are already logged in, continue with Step 2.
Step 2 As needed, complete the "DLP-G76 Provision DCC/GCC Terminations" task.
Step 3 As needed, complete the "DLP-G97 Provision a Proxy Tunnel" task.
Step 4 As needed, complete the "DLP-G98 Provision a Firewall Tunnel" task.
Step 5 As needed, complete the "DLP-G109 Provision Orderwire" task.
Step 6 As needed, complete the "DLP-G110 Create a User Data Channel Circuit" task.
Step 7 As needed, complete the "DLP-G112 Delete Overhead Circuits" task.
Stop. You have completed this procedure.
DLP-G76 Provision DCC/GCC Terminations
Note The DCCs, GCCs, and OSCs should not be provisioned between SONET (ANSI) and SDH (ETSI) nodes using CTC or TL1 because they cannot operate between SONET and SDH nodes. These communication channels should be provisioned on similar nodes, such as SONET-to-SONET or SDH-to-SDH.
Step 1 If you are provisioning DCC termination on the TXP and MXP card, set the termination mode of the card as appropriate. For details, see the section "Termination Modes" in the chapter "Card Reference" of Cisco ONS 15454 DWDM Reference Manual.
Step 2 If you are provisioning DCC termination, ensure that the OTN is disabled on OTN interfaces (usually trunk ports). If OTN is enabled, provision GCC instead of DCC termination. For more information about managing OTN setting on the card, see the procedures for changing card OTN settings in Chapter 5 "Provision Transponder and Muxponder Cards".
Step 3 In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > Comm Channels > GCC tabs.
Step 4 Select the DCC or GCC tabs as necessary. Available tabs are:
•GCC (both ANSI and ETSI)
•DCC
–SDCC and LDCC (for ANSI)
–RS-DCC and MS-DCC (for ETSI)
Step 5 Click the Create button. The Create Terminations dialog box appears.
Step 6 Select the ports where you want to create the DCC/GCC termination. To select more than one port, press the Shift key or the Ctrl key.
Step 7 Under Port Admin State area, select one of the following:
•Leave unchanged—Does not change the DCC/GCC termination port administrative state.
•Set to IS or Set to Unlocked —Puts the DCC/GCC termination port in service.
•Set OOS,DSLBD to IS,AINS (for ANSI) or Set Locked,disabled to Unlocked,automaticInService (for ETSI)—Changes a port that is currently out of service or locked to automatic in service.
•Set OOS,DSLBD to OOS,MT (for ANSI) or Set Locked,disabled to Locked,maintenance (for ETSI)—Changes a port that is currently out of service or locked to out of service for maintenance.
Note For GCC termination, the GCC Rate is set as 192 kbps by default. This rate currently cannot be changed.
Step 8 Verify that the Disable OSPF on Link is unchecked. If this check box is checked, node discovery through the link termination will not happen.
Step 9 If the DCC/GCC termination includes a non-ONS node, check the Far End is Foreign check box. This automatically sets the far-end node IP address to 0.0.0.0, which means that any address can be specified by the far end. To change the default to a specific the IP address, see the "DLP-G184 Change a DCC/GCC Termination" task.
Step 10 In the Layer 3 area, perform one of the following:
•Check the IP box only if the DCC/GCC is between the ONS 15454 and another ONS node and only ONS nodes reside on the network. The DCC/GCC will use Point-to-Point Protocol (PPP).
•Check the IP and OSI boxes if the DCC/GCC is between the ONS 15454 and another ONS node, and third party NEs that use the OSI protocol stack are on the same network. The DCC/GCC will use PPP.
Step 11 If you checked OSI, complete the following steps. If you checked IP only, continue with Step 12.
a. Click Next.
b. Provision the following fields:
–Router—Choose the OSI router.
–ESH—Sets the End System Hello (ESH) propagation frequency. End system (ES) NEs transmit ESHs to inform other ESs and intermediate systems (ISs) about the Network Service Access Points (NSAPs) that they serve. The default is 10 seconds. The range is 10 to 1000 seconds.
–ISH—Sets the Intermediate System Hello (ISH) PDU propagation frequency. IS NEs send ISHs to other ESs and ISs to inform them about the IS NEs that they serve. The default is 10 seconds. The range is 10 to 1000 seconds.
–IIH—Sets the Intermediate System to Intermediate System Hello (IIH) PDU propagation frequency. The IS-IS Hello protocol data units (PDUs) establish and maintain adjacencies between ISs. The default is 3 seconds. The range is 1 to 600 seconds.
–IS-IS Cost—Sets the cost for sending packets on the LAN subnet. The IS-IS protocol uses the cost to calculate the shortest routing path. The default metric cost for LAN subnets is 60. It normally should not be changed.
Step 12 Click Finish. The following alarms appear until all the network DCC/GCC terminations are created and the ports are in service:
•GCC-EOC for GCC termination
•EOC for SDCC termination
•EOC-L for LDCC termination
Step 13 Return to your originating procedure (NTP).
DLP-G97 Provision a Proxy Tunnel
Note If the proxy server is disabled, you cannot set up a proxy tunnel.
Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > Network > Proxy tabs.
Step 2 Click Create.
Step 3 In the Create Tunnel dialog box, complete the following:
•Source Address—Type the IP address of the source node (32 bit length) or source subnet (any other length).
•Length—Choose the length of the source subnet mask.
•Destination Address—Type the IP address of the destination node (32 bit length) or destination subnet (any other length).
•Length—Choose the length of the destination subnet mask.
Step 4 Click OK.
Step 5 Continue with your originating procedure (NTP).
DLP-G98 Provision a Firewall Tunnel
Note If the proxy server is configured as proxy-only or is disabled, you cannot set up a firewall tunnel.
Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > Network > Firewall tabs.
Step 2 Click Create.
Step 3 In the Create Tunnel dialog box, complete the following:
•Source Address—Type the IP address of the source node (32 bit length) or source subnet (any other length).
•Length—Choose the length of the source subnet mask.
•Destination Address—Type the IP address of the destination node (32 bit length) or destination subnet (any other length).
•Length—Choose the length of the destination subnet mask.
Step 4 Click OK.
Step 5 Continue with your originating procedure (NTP).
DLP-G108 Change the Service State for a Port
Step 1 In node view (single-shelf mode) or shelf view (multishelf mode) on the shelf graphic, double-click the card with the port(s) you want to put in or out of service. The card view appears.
Step 2 Click the Provisioning > Line tabs.
Step 3 In the Admin State column for the desired port, choose one of the following from the drop-down list:
•IS (ANSI) or Unlocked (ETSI)—Puts the port in the IS-NR (ANSI) or Unlocked-enabled (ETSI) service state.
•OOS,DSBLD (ANSI) or Locked,disabled (ETSI)—Puts the port in the OOS-MA,DSBLD (ANSI) or Locked-enabled,disabled (ETSI) service state.
For ANSI nodes, traffic is not passed on the port until the service state is changed to IS-NR; OOS-MA,MT; or Out-of-Service and Autonomous, Automatic In-Service (OOS-AU,AINS). For ETSI nodes, traffic is not passed on the port until the service state is changed to Unlocked-enabled; Locked-enabled,maintenance; or Unlocked-disabled,automaticInService.
•OOS,MT (ANSI) or Locked,maintenance (ETSI)—Puts the port in the OOS-MA,MT/Locked-enabled,maintenance service state. This service state does not interrupt traffic flow, but alarm reporting is suppressed and loopbacks are allowed. Raised fault conditions, whether or not their alarms are reported, can be retrieved on the CTC Conditions tab or by using the TL1 RTRV-COND command. Use the OOS-MA,MT/Locked-enabled,maintenance service state for testing or to suppress alarms temporarily. Change to the IS-NR/Unlocked-enabled or OOS-AU,AINS/Unlocked-disabled,automaticInService service states when testing is complete.
•IS,AINS (ANSI) or Unlocked,automaticInService (ETSI)—Puts the port in the OOS-AU,AINS/Unlocked-enabled,automaticInService service state. In this service state, alarm reporting is suppressed, but traffic is carried and loopbacks are allowed. After the soak period passes, the port changes to IS-NR/Unlocked-enabled. Raised fault conditions, whether their alarms are reported or not, can be retrieved on the CTC Conditions tab or by using the TL1 RTRV-COND command.
For more information about service states, refer to the "Administrative and Service States" appendix in the Cisco ONS 15454 DWDM Reference Manual.
Step 4 If you set the Admin State field to IS-AINS or Unlocked,automaticInService, set the soak period time in the AINS Soak field. This is the amount of time that the port will stay in the OOS-AU,AINS or Unlocked-enabled,automaticInService service state after a signal is continuously received. When the soak period elapses, the port changes to the IS-NR or Unlocked-enabled service state.
Step 5 Click Apply. The new port service state appears in the Service State column.
Step 6 As needed, repeat this task for each port.
Step 7 Return to your originating procedure (NTP).
DLP-G109 Provision Orderwire
Step 1 In network view, click the Provisioning > Overhead Circuits tabs.
Step 2 Click Create.
Step 3 In the Overhead Circuit Creation dialog box, complete the following fields in the Circuit Attributes area:
•Name—Assign a name to the circuit. The name can be alphanumeric and up to 48 characters (including spaces).
•Circuit Type—Choose either Local Orderwire or Express Orderwire depending on the orderwire path that you want to create. If regenerators are not used between ONS 15454 nodes, you can use either local or express orderwire channels. If regenerators exist, use the express orderwire channel. You can provision up to four ONS 15454 OC-N ports for each orderwire path.
•PCM—Choose the Pulse Code Modulation voice coding and companding standard, either Mu_Law (North America, Japan) or A_Law (Europe). The provisioning procedures are the same for both types of orderwire.
When provisioning orderwire for ONS 15454s residing in a ring, do not provision a complete orderwire loop. For example, a four-node ring typically has east and west ports provisioned at all four nodes. However, to prevent orderwire loops, provision two orderwire ports (east and west) at all but one of the ring nodes.
Step 4 Click Next.
Step 5 In the Circuit Source area, complete the following:
•Node—Choose the source node.
•Shelf—(Multishelf mode only) Choose the source shelf.
•Slot—Choose the source slot.
•Port—If applicable, choose the source port.
Step 6 Click Next.
Step 7 In the Circuit Destination area, complete the following:
•Node—Choose the destination node.
•Shelf—(Multishelf mode only) Choose the destination shelf.
•Slot—Choose the destination slot.
•Port—If applicable, choose the destination port.
Step 8 Click Finish.
Step 9 Return to your originating procedure (NTP).
DLP-G110 Create a User Data Channel Circuit
Step 1 In network view, click the Provisioning > Overhead Circuits tabs.
Step 2 Click Create.
Step 3 In the Overhead Circuit Creation dialog box, complete the following fields in the Circuit Attributes area:
•Name—Assign a name to the circuit. The name can be alphanumeric and up to 48 characters (including spaces).
•Type—Choose either User Data-F1 or User Data D-4-D-12 from the drop-down list. (User Data D-4-D-12 is not available if the ONS 15454 is provisioned for DWDM.)
Step 4 Click Next.
Step 5 In the Circuit Source area, complete the following:
•Node—Choose the source node.
•Shelf—(Multishelf mode only) Choose the source shelf.
•Slot—Choose the source slot.
•Port—If applicable, choose the source port.
Step 6 Click Next.
Step 7 In the Circuit Destination area, complete the following:
•Node—Choose the destination node.
•Shelf—(Multishelf mode only) Choose the destination shelf.
•Slot—Choose the destination slot.
•Port—If applicable, choose the destination port.
Step 8 Click Finish.
Step 9 Return to your originating procedure (NTP).
DLP-G112 Delete Overhead Circuits
Deleting overhead circuits is service affecting if the circuits are in service (IS). To put circuits out of service (OOS), see the
"DLP-G108 Change the Service State for a Port" task.
Step 1 From the View menu, choose Go to Network View.
Step 2 Click the Provisioning > Overhead Circuits tabs.
Step 3 Click the overhead circuit that you want to delete: local or express orderwire, user data, IP-encapsulated tunnel, or DCC tunnel.
Step 4 Click Delete.
Step 5 In the confirmation dialog box, click Yes to continue.
Step 6 Return to your originating procedure (NTP).
NTP-G62 Create a J0 Section Trace
Step 1 Complete the "DLP-G46 Log into CTC" task at a node on the network where you will create the section trace. If you are already logged in, continue with Step 2.
Step 2 In node view (single-shelf mode) or shelf view (multishelf mode), double-click the TXP or MXP card.
Step 3 Click the Provisioning > Line > Section Trace tabs.
Step 4 From the Port drop-down list, choose the port for the section trace.
Step 5 From the Received Trace Mode drop-down list, enable the section trace expected string by choosing Manual.
Step 6 In the Transmit Section Trace String Size area, click 1 byte or 16 byte. The 1 byte option allows you to enter one character and the 16 byte option allows a 15 character string.
Step 7 In the New Transmit String field, enter the string that you want to transmit. Enter a string that makes the destination port easy to identify, such as the node IP address, node name, or another string. If the New Transmit String field is left blank, the J0 transmits a string of null characters.
Step 8 If you set the Section Trace Mode field to Manual, enter the string that the destination port should receive from the source port in the New Expected String field.
Step 9 Click the Disable AIS and RDI if TIM-P is detected check box if you want to suppress the alarm indication signal (AIS) and remote defect indication (RDI) when the STS Section Trace Identifier Mismatch Path (TIM-P) alarm appears. Refer to the Cisco ONS 15454 DWDM Troubleshooting Guide for descriptions of alarms and conditions.
Step 10 Click Apply.
Step 11 After you set up the section trace, the received string appears in the Received field. The following options are available:
•Click Hex Mode to display section trace in hexadecimal format. The button name changes to ASCII Mode. Click it to return the section trace to ASCII format.
•Click the Reset button to reread values from the port.
•Click Default to return to the section trace default settings (Section Trace Mode is set to Off and the New Transmit and New Expected Strings are null).
Clicking Default will generate alarms if the port on the other end is provisioned with a different string.
The expect and receive strings are updated every few seconds.
Stop. You have completed this procedure.
NTP-G58 Locate and View Optical Channel Network and Client Connections
Purpose |
This procedure allows you to locate and view DWDM OCHNCs and OCHCCs. You can also export circuit data from the Circuits and Edit Circuits windows. |
Tools/Equipment |
None |
Prerequisite Procedures |
G105 Provision Optical Channel Network Connections |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Retrieve or higher |
Step 1 Complete the "DLP-G46 Log into CTC" task at a node on the network where you want to view the circuits. If you are already logged in, continue with Step 2.
Note Do not check Disable Circuit Management in the Login dialog box. No circuits appear if this option is checked.
Step 2 As needed, complete the "DLP-G100 Search for Optical Channel Network and Client Connections" task.
Step 3 As needed, complete the "DLP-G101 View Optical Channel Network and Client Connection Information" task.
Step 4 As needed, complete the "DLP-G102 Filter the Display of Optical Channel Network and Client Connections" task.
Step 5 As needed, complete the "DLP-G103 View Optical Channel Network Connections on a Span" task.
Step 6 As needed, complete the G114 Export CTC Data.
Stop. You have completed this procedure.
DLP-G100 Search for Optical Channel Network and Client Connections
Step 1 Navigate to the appropriate Cisco Transport Controller (CTC) view:
•To search the entire network, choose View > Go to Network View.
•To search for circuits that originate, terminate, or pass through a specific node, choose View > Go to Other Node, then choose the node you want to search and click OK.
•To search for circuits that originate, terminate, or pass through a specific card, double-click the card on the shelf graphic in node view (single-shelf mode) or shelf view (multishelf mode) to open the card in card view.
Step 2 Click the Circuits tab.
Step 3 If you are in node or card view, choose the scope for the search, Node or Network (All), in the Scope drop-down list located at the bottom right side of the screen. Choose Node to see all of the circuits on that node, or Network (All) to see all circuits in the network.
Step 4 Click Search if you need to search through the list of circuits.
Step 5 In the Circuit Name Search dialog box, complete the following:
•Find What—Enter the text of the circuit name you want to find. This field is not case-sensitive.
•Match whole word only—Check this check box to instruct CTC to select circuits only if the entire word matches the text in the Find What field.
•Match case—Check this check box to instruct CTC to select circuits only when the capitalization matches the capitalization entered in the Find What field.
•Direction—Choose the direction for the search. Searches are conducted up or down from the currently selected circuit.
Step 6 Click Find Next. If a match is found the circuit will be highlighted on the Circuits window. To continue the search, click Find Next again to find the next circuit.
Step 7 Repeat Steps 5 and 6 until you are finished, then click Cancel.
Step 8 Return to your originating procedure (NTP).
DLP-G101 View Optical Channel Network and Client Connection Information
Step 1 Navigate to the appropriate CTC view:
•To view circuits for an entire network, choose View > Go to Network View.
•To view circuits that originate, terminate, or pass through a specific node, choose View > Go to Other Node, then choose the node you want to search and click OK.
•To view circuits that originate, terminate, or pass through a specific card, in node view (single-shelf mode) or shelf view (multishelf mode), double-click the card containing the circuits you want to view.
Note In node or card view, you can change the scope of the circuits that appear by choosing Card (in card view), Node, or Network from the Scope drop-down list in the bottom right corner of the Circuits window.
Step 2 Click the Circuits tab. The Circuits tab shows the following information:
Note The following order is the default column sequence, the order might be different on your screen, depending on your individual CTC setup.
•Circuit Name—Name of the circuit. The circuit name can be manually assigned or automatically generated.
•Type—Circuit types are OCHNC, OCHCC, and OCH-Trail.
Note The following circuit types are not applicable to DWDM nodes: STS, VT, VTT (VT tunnel), VAP (VT aggregation point), STS-v (STS VCAT circuit), VT-v (VT VCAT circuit), HOP (high-order circuit), LOP (low-order circuit), VCT (VC low-order tunnel), and VCA (low-order VCAT circuit).
•Size—Circuit size. OCHNC, OCHCC, and OCH-Trail sizes are Equipped not specific, Multi-rate, 2.5 Gbps No FEC (forward error correction), 2.5 Gbps FEC, 10 Gbps No FEC, and 10 Gbps FEC.
Note The following circuit types under the circuit size column are not applicable to DWDM nodes: STS, VT, VCAT, VC12, VC11, VC3, and VC4.
•OCHNC Wlen—The wavelength provisioned for the OCHNC, OCHCC, or OCH trail. See Table 7-2 for a list of channels and wavelengths.
•Direction—The circuit direction, either two-way or one-way.
•OCHNC Dir—The line direction of the OCHNC, OCHCC, or OCH trail, either East to West or West to East. If the direction is West to East, the channel exits from the node through the LINE-TX port of the east OSC-CSM, OPT-BST-E, or OPT-BST-E card, named the East Side Card by Cisco MetroPlanner (typically these cards are hosted in Slot 17). If the direction is East to West, the channel exits from the node through the LINE-TX port of the west OSC-CSM, or OPT-BST, or OPT-BST-E card, named the West Side Card by Cisco MetroPlanner (typically these cards are hosted in Slot 1).
•Protection—The type of circuit protection. See Table 7-3 for a list of protection types.
•Status—The circuit status. Table 7-4 lists the circuit statuses that can appear.
•Source—The circuit source in the format: node/slot/port "port name". The port name will appear in quotes only if a name was assigned to it. (To assign names to ports, see the "DLP-G104 Assign a Name to a Port" task.
•Destination—The circuit destination in the format: node/slot/port "port name". The port name will appear in quotes only if a name was assigned to it. (To assign names to ports, see the "DLP-G104 Assign a Name to a Port" task.
•# of VLANS—The number of VLANs used by an Ethernet circuit. VLANs are not applicable to DWDM nodes.
•# of Spans—The number of internode links that constitute the circuit. Right-clicking the column title shows a shortcut menu from which you can choose Span Details to show or hide circuit span detail.
•State—The circuit service state, which is an aggregate of its cross-connects. For ANSI, the service state is IS, OOS, or OOS-PARTIAL. For ETSI, the service state is Unlocked, Locked, or Locked-partial. For more information about ANSI and ETSI service states, see the "Administrative and Service States" appendix in the Cisco ONS 15454 DWDM Reference Manual.
–IS/Unlocked—All cross-connects are in service and operational.
–OOS/Locked—For ANSI, all cross-connects are Out-of-Service and Management, Maintenance (OOS-MA,MT) and/or Out-of-Service and Management, Disabled (OOS-MA,DSBLD). For ETSI, all cross-connects are Locked-enabled,maintenance and/or Locked-enabled,disabled.
–OOS-PARTIAL/Locked-partial—At least one cross-connect is In-Service and Normal (IS-NR) (ANSI) or Unlocked-enabled (ETSI) and others are out-of-service.
Note Right-clicking a column title (Circuit name, Type, etc.) opens a shortcut menu that allows you to show or hide the desired circuit details.
Step 3 Return to your originating procedure (NTP).
DLP-G102 Filter the Display of Optical Channel Network and Client Connections
Step 1 Navigate to the appropriate CTC view:
•To filter network circuits, choose View > Go to Network View.
•To filter circuits that originate, terminate, or pass through a specific node, choose View > Go to Other Node, then choose the node you want to search and click OK.
•To filter circuits that originate, terminate, or pass through a specific card, double-click the card on the shelf graphic in node view (single-shelf mode) or shelf view (multishelf mode) to open the card in card view.
Step 2 Click the Circuits tab.
Step 3 Set the attributes for filtering the circuit display:
a. Click the Filter button.
b. In the General tab of the Circuit Filter dialog box, set the following filter attributes, as necessary:
•Name—Enter a complete or partial circuit name to filter circuits based on the circuit name; otherwise leave the field blank.
•Direction—Choose one: Any (direction not used to filter circuits), 1-way (display only one-way circuits), or 2-way (display only two-way circuits).
•OCHNC Dir—(DWDM OCHNCs only) Choose one: East to West (displays only east-to-west circuits) or West to East (displays only west-to-east circuits).
•OCHNC Wlen—(DWDM OCHNCs only) Choose an OCHNC wavelength to filter the circuits. For example, choosing 1530.33 will display channels provisioned on the 1530.33-nm wavelength.
•Status—Choose one: Any (status not used to filter circuits) or Discovered (display only discovered circuits). Other statuses do not apply to OCHNCs.
•State—Choose one: OOS (ANSI) or Locked (ETSI) to display only out-of-service circuits; IS (ANSI) or Unlocked (ETSI) to display only in-service circuits (OCHNCs have IS/Unlocked states only); or OOS-PARTIAL (ANSI) or Locked-partial (ETSI) to display only circuits with cross-connects in mixed service states.
•Protection—Enter the circuit protection type to filter circuits based on their protection.
•Shelf—(multishelf nodes only)—Enter the shelf name to filter circuits based on that shelf.
•Slot—Enter a slot number to filter circuits based on the source or destination slot; otherwise leave the field blank.
•Port—Enter a port number to filter circuits based on the source or destination port; otherwise leave the field blank.
•Type—Choose one: Any (type not used to filter circuits), OCHNC (displays only OCHNCs), OCHCC (displays only OCHCCs), or OCH-Trail (displays only OCH trail circuits).
Note The following circuit types are not applicable to DWDM nodes: STS (displays only STS circuits), VT (displays only VT circuits), VT Tunnel (displays only VT tunnels), STS-V (displays STS VCAT circuits), VT-V (displays VT VCAT circuits), and VT Aggregation Point (displays only VT aggregation points), VC_HO_PATH_CIRCUIT (displays VC4 and VC4-Nc circuits), VC_LO_PATH_CIRCUIT (displays only VC3 and VC12 circuits), VC_LO_PATH_TUNNEL (displays only low-order tunnels), VC_LO_PATH_AGGREGATION (displays only log-order aggregation points), VC_HO_PATH_VCAT_CIRCUIT (displays high-order VCAT circuits), and VC_LO_PATH_VCAT_CIRCUIT (displays low-order VCAT circuits).
•Size—Click the appropriate check boxes to filter circuits based on size. The following sizes are available, depending on the circuit type: Multi-rate, Equipment non specific, 2.5 Gbps FEC, 2.5 Gbps No FEC, 10 Gbps FEC, and 10 Gbps No FEC.
Note VT1.5, STS-1, STS3c, STS-6c, STS-9c, STS-12c, STS-24c, STS-48c, and STS-192c are not applicable to ANSI DWDM nodes. VC12, VC3, VC4, VC4-2c, VC4-3c, VC4-4c, VC4-6c, VC4-8c, VC4-9c, VC4-16c, and VC4-64 are not applicable to ETSI DWDM nodes.
The check boxes shown depend on the Type field selection. If you chose Any, all sizes are available. If you chose OCHNC as the circuit type, only Multi-rate, Equipment non specific, 2.5 Gbps FEC, 2.5 Gbps No FEC, 10 Gbps FEC, and 10 Gbps No FEC appear. If you choose OCHCC, only OCHCC is available. If you choose OCH Trail, only Equipment non specific is available.
Step 4 To set the filter for ring, node, link, and source and drop type, click the Advanced tab and complete the following. If you do not want to make advanced filter selections, continue with Step 5.
a. If you made selections on the General tab, click Yes in the confirmation box to apply the settings.
b. In the Advanced tab of the Circuit Filter dialog box, set the following filter attributes as necessary:
•Ring—Choose the ring from the drop-down list.
•Node—Click the check boxes by each node in the network to filter circuits based on node.
•Link—Choose the desired link in the network.
•Source/Drop—Choose one of the following to filter circuits based on whether they have one or multiple sources and drops: One Source and One Drop Only or Multiple Sources or Multiple Drops.
Step 5 Click OK. Circuits matching the attributes in the Filter Circuits dialog box appear in the Circuits window.
Step 6 To turn filtering off, click the Filter icon in the lower right corner of the Circuits window. Click the icon again to turn filtering on, and click the Filter button to change the filter attributes.
Step 7 Return to your originating procedure (NTP).
DLP-G103 View Optical Channel Network Connections on a Span
Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), choose View > Go to Network View. If you are already in network view, continue with Step 2.
Step 2 Right-click the green line between the nodes containing the circuits that you want to view and choose Circuits to view DWDM OCHNCs, OCHCCs, or unprotected circuits on the span.
Step 3 In the Circuits on Span dialog box, view information about the circuits that traverse the span. The information that appears depends on the circuit type. For DWDM OCHNCs, the following information appears:
•Type—The type of circuit, OCHNC, OCHCC, or OCH-Trail.
•Size—The circuit size.
•OCHNC Wavelength—The wavelength provisioned for the OCHNC.
•DIR—2-way or 1-way.
•Circuit—The OCHNC circuit name.
•OCHNC Dir—The direction provisioned for the OCHNC, either east-to-west or west-to-east.
Step 4 Return to your originating procedure (NTP).
Feedback