Cisco ONS 15454 DWDM Procedure Guide, Release 7.0

Before You Begin
NTP-G41 Perform the Terminal or Hub Node with 32MUX-O and 32DMX-O Cards Acceptance Test
NTP-G42 Perform the Terminal Node with 32WSS and 32DMX Cards Acceptance Test
- DLP-G270 Verify the 32DMX Power
NTP-G153 Perform the Terminal Node with 32WSS-L and 32DMX-L Cards Acceptance Test
NTP-G43 Perform the ROADM Node with 32WSS and 32DMX Cards Acceptance Test
NTP-G154 Perform the ROADM Node with 32WSS-L and 32DMX-L Cards Acceptance Test
NTP-G44 Perform the Anti-ASE Hub Node Acceptance Test
NTP-G45 Perform the C-Band Line Amplifier Node with OSCM Cards Acceptance Test
NTP-G155 Perform the L-Band Line Amplifier Node with OSCM Cards Acceptance Test
NTP-G46 Perform the C-Band Line Amplifier Node with OSC-CSM Cards Acceptance Test
NTP-G156 Perform the L-Band Line Amplifier Node with OSC-CSM Cards Acceptance Test
NTP-G47 Perform the C-Band Line Amplifier Node with OSCM and OSC-CSM Cards Acceptance Test
NTP-G157 Perform the L-Band Line Amplifier Node with OSCM and OSC-CSM Cards Acceptance Test
NTP-G48 Perform the OADM Node Acceptance Test on a Symmetric Node with OSCM Cards
NTP-G49 Perform the OADM Active Node Acceptance Test on a Symmetric Node with OSC-CSM Cards
NTP-G50 Perform the OADM Passive Node Acceptance Test on a Symmetric Node with OSC-CSM Cards
- DLP-G82 Verify the OSC-CSM Power

Perform Node Acceptance Tests

This chapter provides test procedures to verify that the cards installed in the ONS 15454 are performing correctly. The procedures are optional.

Note Unless otherwise specified, "ONS 15454" refers to both ANSI (SONET) and ETSI (SDH) shelf assemblies.

Note This chapter does not test the TXP or MXP card installation. TXP and MXP card installation and verification is performed in Chapter 5 "Provision Transponder and Muxponder Cards."

Before You Begin

This section lists the non-trouble procedures (NTPs) that you need to complete to validate a dense wavelength division multiplexing (DWDM) node. Turn to a procedure for applicable detailed level procedures (DLPs).

1. G41 Perform the Terminal or Hub Node with 32MUX-O and 32DMX-O Cards Acceptance Test—Complete this procedure to test terminal and hub nodes with 32MUX-O and 32DMX-O cards installed.

2. G42 Perform the Terminal Node with 32WSS and 32DMX Cards Acceptance Test—Complete this procedure to test terminal nodes with 32WSS and 32DMX cards installed.

3. G153 Perform the Terminal Node with 32WSS-L and 32DMX-L Cards Acceptance Test—Complete this procedure to test terminal nodes with 32WSS-L and 32DMX-L cards installed.

4. G43 Perform the ROADM Node with 32WSS and 32DMX Cards Acceptance Test—Complete this procedure to test reconfigurable optical add/drop multiplexing (ROADM) nodes with 32WSS and 32DMX cards installed.

5. G154 Perform the ROADM Node with 32WSS-L and 32DMX-L Cards Acceptance Test—Complete this procedure to test reconfigurable optical add/drop multiplexing (ROADM) nodes with 32WSS-L and 32DMX-L cards installed.

6. G44 Perform the Anti-ASE Hub Node Acceptance Test—Complete this procedure to test anti-amplified spontaneous emission (anti-ASE) hub nodes.

7. G45 Perform the C-Band Line Amplifier Node with OSCM Cards Acceptance Test—Complete this procedure to test C-band line amplifier nodes with OSCM cards installed on both the east and west sides of the shelf.

8. G155 Perform the L-Band Line Amplifier Node with OSCM Cards Acceptance Test—Complete this procedure to test L-band line amplifier nodes with OSCM cards installed on both the east and west sides of the shelf.

9. G46 Perform the C-Band Line Amplifier Node with OSC-CSM Cards Acceptance Test—Complete this procedure to test C-band line amplifier nodes with OSC-CSM cards installed on both the east and west sides of the shelf.

10. G156 Perform the L-Band Line Amplifier Node with OSC-CSM Cards Acceptance Test—Complete this procedure to test L-band line amplifier nodes with OSC-CSM cards installed on both the east and west sides of the shelf.

11. G47 Perform the C-Band Line Amplifier Node with OSCM and OSC-CSM Cards Acceptance Test—Complete this procedure to test C-band line amplifier nodes with OSCM and OSC-CSM cards installed.

12. G157 Perform the L-Band Line Amplifier Node with OSCM and OSC-CSM Cards Acceptance Test—Complete this procedure to test L-band line amplifier nodes with OSCM and OSC-CSM cards installed.

13. G48 Perform the OADM Node Acceptance Test on a Symmetric Node with OSCM Cards—Complete this procedure to test optical add/drop multiplexing (OADM) nodes with OSCM cards installed on both the east and west sides of the shelf.

14. G49 Perform the OADM Active Node Acceptance Test on a Symmetric Node with OSC-CSM Cards—Complete this procedure to test OADM nodes with OSC-CSM and OPT-BST or OPT-BST-E cards installed on both the east and west sides of the shelf.

15. G50 Perform the OADM Passive Node Acceptance Test on a Symmetric Node with OSC-CSM Cards—Complete this procedure to test OADM nodes with OSC-CSM cards installed on both the east and west sides of the shelf and no OPT-BST or OPT-BST-E cards.

NTP-G41 Perform the Terminal or Hub Node with 32MUX-O and 32DMX-O Cards Acceptance Test


Purpose	This procedure tests a DWDM terminal or hub node provisioned for C-band wavelengths with 32MUX-O and 32DMX-O cards installed.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_C An optical power meter or optical spectrum analyzer 2 bulk attenuators (10 dB) with LC connectors
Prerequisite Procedures	Chapter 3 "Turn Up a Node"
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note This procedure tests the west side of hub nodes first, then the east side. If you are testing a terminal node, apply instructions for the west side of the hub node to the terminal side (east or west) of the terminal node.

Note Optical power measurements require either a tunable laser or a multirate transponder to generate the proper optical wavelength. If multirate transponders were installed during completion of Chapter 3 "Turn Up a Node," they can be used for this procedure. No additional cabling changes are needed.

Step 1 Complete the "DLP-G46 Log into CTC" task at the hub or terminal node that you want to test. If you are already logged in, continue with Step 2.

Step 2 From the View menu, choose Go to Network View.

Step 3 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

b. Verify that no equipment alarms appear indicating equipment failure or other hardware problems. (Equipment alarms are indicated by an EQPT in the Alarms tab Cond column.) If equipment failure alarms appear, investigate and resolve them before continuing. Refer to the Cisco ONS 15454 DWDM Troubleshooting Guide for procedures.

Note If optical service channel (OSC) terminations are created, there will be two alarms, one for low power on the OPT-BST or OPT-BST-E card, and the other an OSC channel alarm.

Step 4 In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Port Status tabs. Verify that all statuses under Link Status are listed as Success - Changed, Success - Unchanged, or Not Applicable. If any are not, complete the "NTP-G37 Run Automatic Node Setup" procedure.

Step 5 Create a physical loopback on the west (or terminal) OPT-BST or OPT-BST-E amplifier by using a patchcord with 10-dB bulk attenuators to connect the LINE TX port to the LINE RX port.

Note An SDCC Termination Failure alarm will appear due to the OSC signal loopback.

Step 6 Verify that the OSC link becomes active on the west OSCM or OSC-CSM card. (The OSC termination must already be provisioned. If not, complete the "NTP-G38 Provision OSC Terminations" procedure.)

Step 7 Set the tunable laser or the TXP_MR_10E_C card to the first wavelength of the 100-GHz ITU-T C-band grid (1530.33 nm). Refer to the tunable laser manufacturer's documentation or the "DLP-G268 Provision TXP_MR_10E_C Cards for Acceptance Testing" task.

Step 8 Connect the tunable laser transmitter or TXP_MR_10E_C card DWDM TX port to the CHAN RX 01 port on the west (or terminal) 32MUX-O card using the available patch panel.

Step 9 Display the west (or terminal) 32MUX-O card in card view.

Step 10 Click the Provisioning > Optical Chn > Parameters tabs.

Step 11 Change the Port 1 administrative state to OOS,MT (ANSI) or Locked,maintenance (ETSI).

Step 12 Verify that the Port 1 power level reaches the provisioned VOA Power Ref setpoint.

Note The tunable laser minimum output optical power (Pout) must be 6 dBm. If the output power is lower than the specified value, the 32MUX-O card might not reach the provisioned setpoint.

Step 13 If an OPT-BST OR OPT-BST-E card is installed, complete the "DLP-G79 Verify the OPT-BST, OPT-BST-E, or OPT-BST-L Amplifier Laser and Power" task on the west (or terminal) OPT-BST, OPT-BST-E or OPT-BST-L o ensure that the amplifier is working properly.

Step 14 Complete the "DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task on the west (or terminal) OPT-PRE card to ensure that the amplifier is working properly.

Step 15 Complete the "DLP-G78 Verify the 32MUX-O Card Power" task to verify that the 32MUX-O is powered correctly.

Step 16 Complete the "DLP-G269 Verify the 32DMX-O Card Power" task to verify that the 32DMX-O card is powered correctly.

Step 17 Restore the default IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) administrative state to the 32MUX-O port that was changed to OOS,MT (ANSI) or Locked,maintenance (ETSI) in Step 11.

Step 18 Repeat Steps 7 through 17 for the remaining 31 wavelengths of the 100-GHz grid to verify the correct behavior of all variable optical attenuators (VOAs) inside the 32MUX-O card.

Step 19 Remove the loopback created in Step 5.

Step 20 If the node is a hub node, repeat Steps 5 through 19 for the east side cards.

Step 21 Complete the "NTP-G37 Run Automatic Node Setup" procedure to restore the original configuration.

Step 22 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

Stop. You have completed this procedure.

DLP-G268 Provision TXP_MR_10E_C Cards for Acceptance Testing


Purpose	This procedure provisions a TXP_MR_10E_C card for acceptance testing when a tunable laser is not available.
Tools/Equipment	TXP_MR_10E_C
Prerequisite Procedures	G32 Install the Transponder and Muxponder Cards G34 Install Fiber-Optic Cables on DWDM Cards and DCUs
Required/As Needed	As needed
Onsite/Remote	Onsite
Security Level	Superuser

Step 1 If you have installed and verified the TXP_MR_10E_C card, continue with Step 2. If not, install the TXP card using the "NTP-G32 Install the Transponder and Muxponder Cards" procedure.

Step 2 Display the TXP_MR_10E_C in card view.

Step 3 Click the Provisioning > Line > SONET (ANSI) or SDH (ETSI) tabs.

Step 4 Click the Admin State column for the trunk port and choose OOS,DSBLD (ANSI) or Locked,disabled (ETSI) from the drop-down list.

Step 5 Click Apply, then click Yes.

Step 6 Click the Provisioning > Line > Wavelength Trunk Settings tabs.

Step 7 In the Wavelength field, choose the first wavelength required by the acceptance test.

Step 8 Click Apply.

Step 9 Click the Provisioning > Line > SONET (ANSI) or SDH (ETSI) tabs.

Step 10 Click the Admin State column for the trunk port and choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list.

Step 11 Click Apply.

Step 12 Connect a power meter to the DWDM TX port. Verify that the output power falls within 4.5 dBm and + or - 1 dBm. If it does not fall within this range, replace the card or contact your next level of support.

Step 13 Return to your originating procedure (NTP).

DLP-G79 Verify the OPT-BST, OPT-BST-E, or OPT-BST-L Amplifier Laser and Power


Purpose	This task verifies that the OPT-BST, OPT-BST-E, or OPT-BST-L amplifier laser is on and provisioned to the correct power.
Tools/Equipment	None
Prerequisite Procedures	G46 Log into CTC
Required/As Needed	As needed
Onsite/Remote	Onsite or remote
Security Level	Superuser

Step 1 In node view (single-shelf mode) or shelf view (multishelf mode), double-click the OPT-BST, OPT-BST-E, or OPT-BST-L amplifier to display the card view.

Step 2 Click the Maintenance > ALS tabs. If the value in the Currently Shutdown field is NO, continue with Step 3. If not, complete the following steps:

a. Check the optical safety remote interlock (OSRI) setting. If it is set to On, change it to Off. If the OSRI setting is set to Off and the Currently Shutdown field is Yes, contact your next level of support.

b. Click Apply, then click Yes.

c. Check the Currently Shutdown field. If it changes to NO, continue with Step 3. If not, contact your next level of support. The amplifier might need to be replaced.

Step 3 Click the Provisioning > Opt Ampli Line > Parameters tabs.

Step 4 Click Reset.

Step 5 Scroll to the right and locate the Signal Output Power parameter for Port 6 (LINE-TX). Verify that the Signal Output Power value is greater than or equal to 1.5 dBm.

If the Signal Output Power is not greater than or equal to 1.5 dBm, do not continue. Begin troubleshooting or contact your next level of support.

Step 6 Return to your originating procedure (NTP).

DLP-G80 Verify the OPT-PRE Amplifier Laser and Power


Purpose	This task verifies that the OPT-PRE amplifier laser is on and provisioned to the correct power.
Tools/Equipment	None
Prerequisite Procedures	G46 Log into CTC
Required/As Needed	As needed
Onsite/Remote	Onsite or remote
Security Level	Superuser

Step 1 In node view (single-shelf view) or shelf view (multishelf view), double-click the OPT-PRE amplifier to display the card view.

Step 2 Click the Maintenance > ALS tabs.

Step 3 If the value shown in the Currently Shutdown field is NO, continue with Step 4. If the OSRI value is set to On, change it to Off. If the OSRI setting is set to Off and the Currently Shutdown field is Yes, contact your next level of support.If not, complete the following steps:

a. If the OSRI setting is set to ON, click the table cell and choose OFF from the drop-down list.

b. Click Apply, then click Yes.

c. Check the Currently Shutdown field. If it changes to NO, continue with Step 4. If not, contact your next level of support. The amplifier might need to be replaced.

Step 4 Click the Provisioning > Opt Ampli Line > Parameters tabs.

Step 5 Locate the Signal Output Power parameter for Port 2 (COM-TX). Verify that the Signal Output Power value is greater than or equal to 1.5 dBm. If the Signal Output Power is greater than or equal to 1.5 dBm, continue with Step 6. If the Signal Output Power is less than 1.5 dBm, check your connections and clean the fibers using the "NTP-G115 Clean Fiber Connectors" procedure. If this does not change the power value, consult your next level of support.

Step 6 Scroll to the right to locate the DCU Insertion Loss parameter. Verify that the DCU Insertion Loss value is less than or equal to 10 dB.

If the DCU Insertion Loss is greater than 10 dB, do not continue. Begin troubleshooting or contact your next level of support.

Step 7 Return to your originating procedure (NTP).

DLP-G78 Verify the 32MUX-O Card Power


Purpose	This task verifies 32MUX-O card power.
Tools/Equipment	None
Prerequisite Procedures	G46 Log into CTC
Required/As Needed	As needed
Onsite/Remote	Onsite or remote
Security Level	Superuser

Step 1 Display the 32MUX-O card in card view.

Step 2 Click the Provisioning > Optical Chn > Parameters tabs.

Step 3 Change the administrative state of the corresponding port to OOS,MT (ANSI) or Locked,maintenance (ETSI).

Step 4 Click Apply, then click Yes.

Step 5 Check that the value in the Power column for the port reaches the value shown in the VOA Power Ref column.

Step 6 Return to your originating procedure (NTP).

DLP-G269 Verify the 32DMX-O Card Power


Purpose	This task verifies that the 32DMX-O card is provisioned to the correct power.
Tools/Equipment	None
Prerequisite Procedures	G46 Log into CTC
Required/As Needed	As needed
Onsite/Remote	Onsite or remote
Security Level	Superuser

Step 1 Display the 32DMX-O card in card view.

Step 2 Click the Provisioning > Optical Chn > Parameters tabs.

Step 3 Change the administrative state for the appropriate port to OOS,DSBLD (ANSI) or Locked,disabled (ETSI).

Step 4 Click Apply, then click Yes.

Step 5 Verify that the value in the Power table cell is the same as the VOA Power Ref table cell value for the port under test.

Step 6 (Optional) Connect a power meter to the CHAN TX 01 port through the patch panel. Verify that the physical optical power value coming from drop Port 1 on the west 32DMX-O card is consistent with the value read (the maximum allowed error is +/- 0.5 dBm).

Step 7 Return to your originating procedure (NTP).

NTP-G42 Perform the Terminal Node with 32WSS and 32DMX Cards Acceptance Test


Purpose	This acceptance test verifies that a terminal node provisioned for C-band wavelengths is operating properly before you connect it to the network. The test verifies that each add/drop and pass-through port on the 32WSS and 32DMX cards operates properly and verifies the operation of the amplifiers. The test also checks the power levels at each transmit and receive port to ensure that power loss in the cabling is within tolerance. If MMU cards are installed, the test verifies that the MMU insertion loss doesn't impact add, drop, or pass-through circuits.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_C An optical power meter or optical spectrum analyzer 1 bulk attenuator (10 dB) with LC connectors
Prerequisite Procedures	Chapter 3 "Turn Up a Node"
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note This procedure creates an optical loopback on the OPT-BST or OPT-BST-E line. An optical signal is sent from the 32WSS input (add) to the OPT-BST or OPT-BST-E common receive (RX) and back out the OPT-BST or OPT-BST-E transmit (TX) line. The OPT-BST or OPT-BST-E line receives the looped signal from the OPT-BST or OPT-BST-E TX. It then passes the signal to the OPT-BST or OPT-BST-E common TX and into the OPT-PRE common RX. The OPT-PRE sends the signal to the 32DMX. The optical signal from the tunable laser or TXP_MR_10E_C must pass successfully through the 32WSS and out the 32DMX.

Step 1 Complete the "DLP-G46 Log into CTC" task at the terminal node that you want to test. If you are already logged in, continue with Step 2.

Step 2 Display the terminal node in node view (single-shelf mode) or multishelf view (multishelf mode).

Step 3 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

b. Verify that no equipment alarms (indicated by EQPT in the Cond column) appear indicating equipment failure or other hardware problems. If equipment failure alarms appear, investigate and resolve them before continuing. Refer to the Cisco ONS 15454 DWDM Troubleshooting Guide for procedures.

Note If OSC terminations are created, an OSC channel alarm will appear.

Step 4 In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Port Status tabs. Verify that all statuses under Link Status are listed as Success - Changed, Success - Unchanged, or Not Applicable. If any are not, or if errors (indicated in red) appear, delete the OSC channels and complete the "NTP-G37 Run Automatic Node Setup" procedure. Provision the OSC channels when complete.

Step 5 Create a physical loopback on the OPT-BST, OPT-BST-E, or OSC-CSM card by using a patchcord with 10-dB bulk attenuators to connect the LINE TX port to the LINE RX port.

Note A SDCC Termination Failure alarm will appear due to the OSC signal loopback. This is observed as an alarm on Port 1 of the OSCM or OSC-CSM card.

Step 6 Wait approximately two minutes, then verify that the OSC link is active on the west OSCM or OSC-CSM card by observing whether or not the loss of signal (LOS) alarm on the OSCM or OSC-CSM (and the OPT-BST or OPT-BST-E card, if present) clears. (The OSC termination must already be provisioned. If not, complete the "NTP-G38 Provision OSC Terminations" procedure.)

Step 7 If you are using a tunable laser, follow the manufacturer's instructions to complete the following steps. If you are using a TXP_MR_10E_C card, continue with Step 8.

a. Set the output power to a nominal value, such as -3 dBm.

b. Set the tuner to the wavelength you will test, then continue with Step 9.

Step 8 If you are using a TXP_MR_10E_C card, complete the "DLP-G268 Provision TXP_MR_10E_C Cards for Acceptance Testing" task for the TXP containing the wavelength you will test. Refer to Table 4-1, if needed.

Step 9 Connect the tunable laser transmitter or the TXP_MR_10E_C card DWDM TX port to the CHAN RX 01 port on the 32WSS card using the available patch panel.

Note The tunable laser minimum output optical power (Pout) must be -6 dBm. If the output power is lower than -6 dBm, the 32WSS card might not reach the provisioned setpoint.

Step 10 Display the 32WSS card in card view.

Step 11 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the optical connector number that carries the wavelengths you will test. Refer to Table 4-1, if needed.

Step 12 Click the Admin State table cell for the add (CHAN-RX) port carrying the tested wavelength, then choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list. For example, if the tested wavelength is 1530.33 nm (shown as 1530.3), you would click the Port 1 (CHAN-RX) Admin State field and choose OOS,MT or Locked,maintenance from the drop-down list.

Step 13 Change the administrative state of the pass-through port corresponding to the port in Step 9 to OOS,MT (ANSI) or Locked,maintenance (ETSI). For example, if the tested wavelength is 1530.33 nm (shown as 1530.3), you would click the Port 33 (PASS-THROUGH) Admin State field and choose OOS,MT or Locked,maintenance from the drop-down list. Refer to Table 4-1, if needed.

Step 14 Click Apply, then click Yes.

Step 15 Click the Maintenance tab.

Step 16 For Channel #1, change Operating Mode to Add Drop.

Step 17 Click Apply, then click Yes.

Step 18 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the optical connector number that carries the wavelength under test.

Step 19 Verify that the actual power coming from the tunable laser or TXP_MR_10E_C card shown under the Power column is equal to the specified VOA Power Ref power (+/- 0.2dB) shown in the same row.

Step 20 Click the Optical Line tab.

Step 21 Verify that the power value from Step 19 reaches the Shelf i Slot i (32WSS or 32DMX).Port COM-TX.Power set point +/- 1.0 dBm. To view this set point:

a. In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Provisioning tabs.

b. In the Selector window on the left, expand the 32WSS or 32DMX card.

c. Expand the Port COM-TX category.

d. Select Power.

e. View the value of the Shelf i Slot i (32WSS or 32DMX).Port COM-TX.Power parameter on the right pane.

f. If the power value does not match the value recorded in Step 19 (+/- 0.5 dB), contact your next level of support.

Step 22 If an OPT-BST or OPT-BST-E card is installed, complete the "DLP-G79 Verify the OPT-BST, OPT-BST-E, or OPT-BST-L Amplifier Laser and Power" task on the OPT-BST or OPT-BST-E to ensure that the amplifier is working properly.

Step 23 If an OSC- CSM is installed, continue with Step 25. If an OPT-BST is installed, verify the connection between Port 67 (COM-TX) on the 32WSS and Port 1 (COM-RX) on the OPT-BST or OPT-BST-E cards:

a. Display the 32WSS card in card view.

b. Click the Provisioning > Optical Line tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. Display the OPT-BST or OPT-BST-E card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port 1 (COM-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST or OPT-BST-E and 32WSS cards. Check the values again. If they still do not match, contact your next level of support.

Step 24 If an OPT-BST, OPT-BST-E, or OPT-BST-L card is installed on the west or terminal side, complete the "DLP-G79 Verify the OPT-BST, OPT-BST-E, or OPT-BST-L Amplifier Laser and Power" task to ensure the amplifier is working properly.

Step 25 Complete the following steps to verify the connection between Port 67 (COM-TX) on the 32WSS and the Port 2 (COM-RX) on the OSC-CSM card:

a. Display the 32WSS card in card view.

b. Click the Provisioning > Optical Line tabs.

c. Record the value in Power table cell for Port 67 (COM-TX).

d. Display the OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port 2 (COM-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OSC-CSM and 32WSS cards. Check the values again. If they still do not match, contact your next level of support.

Step 26 Complete the following steps to verify the connection between Port 2 (COM-TX) on the OPT-PRE card and Port 33(COM-RX) on the 32DMX card:

a. Display the OPT-PRE card in card view.

b. Click the Provisioning > OptAmpliLine > Parameters tabs.

c. Record the value in Power table cell for Port 2 (COM-TX).

d. Display the 32DMX card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port33 (COM-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-PRE and 32DMX cards. Check the values again. If they still do not match, contact your next level of support.

Step 27 Complete the "DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task on the OPT-PRE to ensure that the amplifier is working properly.

Step 28 Complete the "DLP-G270 Verify the 32DMX Power" task to verify that the 32DMX card is powered correctly.

Step 29 Display the 32WSS in card view.

Step 30 Click the Maintenance tab.

Step 31 For the circuit (channel) under test, click the Operating Mode table cell and choose Not Assigned from the drop-down list.

Step 32 Click Apply, then Yes.

Step 33 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the optical connector number that carries the wavelength under test.

Step 34 Click the Admin State table cell. Choose IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) from the drop-down list for all ports that were changed to OOS,MT or Locked,maintenance.

Step 35 Repeat Steps 7 through 34 for the remaining 31 wavelengths of the 100-Ghz grid to verify the correct behavior of all VOAs inside the 32WSS card.

Step 36 Disconnect the TXP card or tunable laser from the 32WSS card.

Step 37 Remove the loopback created in Step 5.

Step 38 Complete the "NTP-G37 Run Automatic Node Setup" procedure to restore the original configuration.

Step 39 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

Stop. You have completed this procedure.

DLP-G270 Verify the 32DMX Power


Purpose	This task verifies that the 32DMX card is provisioned to the correct power.
Tools/Equipment	None
Prerequisite Procedures	G46 Log into CTC
Required/As Needed	As needed
Onsite/Remote	Onsite or remote
Security Level	Superuser

Step 1 Display the 32DMX card in card view.

Step 2 Click the Provisioning > Optical Line > Parameters tabs.

Step 3 Change the administrative state for Port 33 (COM TX) to OOS,MT (ANSI) or Locked,maintenance (ETSI)

Step 4 Verify that the value shown in the VOA Power Ref column reaches the provisioned setpoint.

Step 5 (Optional) Connect a power meter to the CHAN TX 01 port through the patch panel. Verify that the physical optical power value coming from the 32DMX drop Port 1 is consistent with the Power value on the Parameters tab, +/- 1 dBm.

Step 6 Change the administrative state for Port 1 to OOS,DSBLD (ANSI) or Locked,disabled (ETSI).

Step 7 Return to your originating procedure (NTP).

NTP-G153 Perform the Terminal Node with 32WSS-L and 32DMX-L Cards Acceptance Test


Purpose	This acceptance test verifies that a terminal node provisioned for L-band wavelengths is operating properly before you connect it to the network. The test verifies that each add/drop and pass-through port on the 32WSS-L and 32DMX-L cards operates properly and verifies the operation of the amplifiers. The test also checks the power levels at each transmit and receive port to ensure that power loss in the cabling is within tolerance. If MMU cards are installed, the test verifies that the MMU insertion loss doesn't impact add, drop, or pass-through circuits.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_L An optical power meter or optical spectrum analyzer 1 bulk attenuator (10 dB) with LC connectors
Prerequisite Procedures	Chapter 3 "Turn Up a Node"
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note This procedure creates an optical loopback on the OPT-BST-L line. An optical signal is sent from the 32WSS-L input (add) to the OPT-BST-L common RX and back out the OPT-BST-L TX line. The OPT-BST-L line receives the looped signal from the OPT-BST-L TX. It then passes the signal to the OPT-BST-L common TX and into the OPT-AMP-L (when provisioned in OPT-PRE mode) common RX. The OPT-AMP-L card sends the signal to the 32DMX-L card. The optical signal from the tunable laser or TXP_MR_10E_L card must pass successfully through the 32WSS-L card and out the 32DMX-L card.

Step 1 Complete the "DLP-G46 Log into CTC" task at the hub or terminal node that you want to test. If you are already logged in, continue with Step 2.

Step 2 Display the terminal node in node view (single-shelf mode) or multishelf view (multishelf mode).

Step 3 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

Note If OSC terminations are created, an OSC channel alarm will appear.

Step 4 In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Port Status tabs. Verify that all statuses under Link Status are listed as Success - Changed, Success - Unchanged, or Not Applicable. If any are not, or if errors (indicated in red) appear, delete the OSC channels and complete the "NTP-G37 Run Automatic Node Setup" procedure. Provision the OSC channels when complete.

Step 5 Create a physical loopback on the OPT-BST-L, OCSM, or OSC-CSM card by using a patchcord with 10-dB bulk attenuators to connect the LINE TX port to the LINE RX port.

Note An SDCC Termination Failure alarm will appear due to the OSC signal loopback. This is observed as an alarm on Port 1 of the OSCM or OSC-CSM card.

Step 6 Wait approximately two minutes, then verify that the OSC link is active on the west OSCM or OSC-CSM card by observing whether or not the LOS alarm on the OSCM or OSC-CSM card (and the OPT-BST-L card, if present) clears. (The OSC termination must already be provisioned. If not, complete the "NTP-G38 Provision OSC Terminations" procedure.)

Step 7 If you are using a tunable laser, follow the manufacturer's instructions to complete the following steps. If you are using a TXP_MR_10E_L card, continue with Step 8.

a. Set the output power to a nominal value, such as -3 dBm.

b. Set the tuner to the wavelength you will test, then continue with Step 9.

Step 8 If you are using a TXP_MR_10E_L card, complete the "DLP-G358 Provision TXP_MR_10E_L Card for Acceptance Testing" task for the TXP containing the wavelength you will test.

Step 9 Connect the tunable laser transmitter or the TXP_MR_10E_L card DWDM TX port to the CHAN RX 01 port on the 32WSS-L card using the available patch panel.

Note The tunable laser minimum Pout must be -6 dBm. If the output power is lower than -6 dBm, the 32WSS-L card might not reach the provisioned setpoint.

Step 10 Display the 32WSS-L card in card view.

Step 12 Click the Admin State table cell for the add (CHAN-RX) port carrying the tested wavelength, then choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list. For example, if the tested wavelength is 1577.86 nm (shown as 1577.8), you would click the Port 1 (CHAN-RX) Admin State field and choose OOS,MT or Locked,maintenance from the drop-down list.

Step 13 Change the administrative state of the pass-through port corresponding to the port in Step 9 to OOS,MT (ANSI) or Locked,maintenance (ETSI). For example, if the tested wavelength is 1577.86 nm (shown as 1577.86), you would click the Port 33 (PASS-THROUGH) Admin State field and choose OOS,MT or Locked,maintenance from the drop-down list. Refer to Table 4-2, if needed.

Step 14 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the optical connector number that carries the wavelength under test.

Step 15 Click Apply, then click Yes.

Step 16 Click the Maintenance tab.

Step 17 For Channel #1, change Operating Mode to Add Drop.

Step 18 Click Apply, then click Yes.

Step 19 Click the Provisioning > Optical Chn > Parameters n tabs where n = the optical connector number that carries the wavelength under test.

Step 20 Verify that the actual power coming from the tunable laser or TXP_MR_10E_L card shown under the Power column is equal to the specified VOA Power Ref power (+/- 0.2 dB) shown in the same row.

Step 21 Click the Optical Line tab.

Step 22 Verify that the TX COM port (#67) has the same Power column value as the VOA Power Ref setpoint (+/- 0.5 dB) in Step 20. This verifies that the optical signal is traveling correctly through the 32WSS-L card.

Step 23 If an OPT-BST-L card is installed, complete the "DLP-G359 Verify the OPT-BST-L or OPT-AMP-L (OPT-Line Mode) Amplifier Laser and Power" task on the OPT-BST-L to ensure that the amplifier is working properly.

Step 24 If an OSC- CSM is installed, continue with Step 25. If an OPT-BST-L is installed, verify the connection between Port 67 (COM-TX) on the 32WSS-L and Port 1 (COM-RX) on the OPT-BST-L cards:

a. Display the 32WSS-L card in card view.

b. Click the Provisioning > Optical Line tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. Display the OPT-BST-L card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port 1 (COM-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST-L and 32WSS-L cards. Check the values again. If they still do not match, contact your next level of support.

Step 25 If an OPT-BST-L card is installed on the west or terminal side, complete the "DLP-G79 Verify the OPT-BST, OPT-BST-E, or OPT-BST-L Amplifier Laser and Power" task to ensure the amplifier is working properly.

Step 26 Complete the following steps to verify the connection between Port 67 (COM-TX) on the 32WSS-L and the Port 2 (COM-RX) on the OSC-CSM card:

a. Display the 32WSS-L card in card view.

b. Click the Provisioning > Optical Line tabs.

c. Record the value in Power table cell for Port 67 (COM-TX).

d. Display the OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port 2 (COM-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OSC-CSM and 32WSS-L cards. Check the values again. If they still do not match, contact your next level of support.

Step 27 Complete the following steps to verify the connection between Port 2 (COM-TX) on the OPT-AMP-L card provisioned in OPT-PRE mode and Port 33(COM-RX) on the 32DMX-L card:

a. Display the OPT-AMP-L card in card view.

b. Click the Provisioning > OptAmpliLine > Parameters tabs.

c. Record the value in Power table cell for Port 2 (COM-TX).

d. Display the 32DMX-L card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port33 (COM-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-AMP-L and 32DMX-L cards. Check the values again. If they still do not match, contact your next level of support.

Step 28 Complete the "DLP-G360 Verify the OPT-AMP-L (OPT-PRE Mode) Amplifier Laser and Power" task on the OPT-PRE to ensure that the amplifier is working properly.

Step 29 Complete the "DLP-G361 Verify the 32DMX-L Power" task to verify that the 32DMX card is powered correctly.

Step 30 Display the 32WSS-L in card view.

Step 31 Click the Maintenance tab.

Step 32 For the circuit (channel) under test, click the Operating Mode table cell and choose Not Assigned from the drop-down list.

Step 33 Click Apply, then Yes.

Step 34 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the optical connector number that carries the wavelength under test.

Step 35 Click the Admin State table cell. Choose IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) from the drop-down list for all ports that were changed to OOS,MT or Locked,maintenance.

Step 36 Repeat Steps 7 through 34 for the remaining 31 wavelengths of the 100-Ghz grid to verify the correct behavior of all VOAs inside the 32WSS-L card.

Step 37 Disconnect the TXP card or tunable laser from the 32WSS-L card.

Step 38 Remove the loopback created in Step 5.

Step 39 Complete the "NTP-G37 Run Automatic Node Setup" procedure to restore the original configuration.

Step 40 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

Stop. You have completed this procedure.

DLP-G358 Provision TXP_MR_10E_L Card for Acceptance Testing


Purpose	This procedure provisions a TXP_MR_10E_L card for acceptance testing when a tunable laser is not available.
Tools/Equipment	TXP_MR_10E_L
Prerequisite Procedures	G32 Install the Transponder and Muxponder Cards G34 Install Fiber-Optic Cables on DWDM Cards and DCUs
Required/As Needed	As needed
Onsite/Remote	Onsite
Security Level	Superuser

Step 1 If you have installed and verified the TXP_MR_10E_L card, continue with Step 2. If you have not installed it, install the card using the "NTP-G32 Install the Transponder and Muxponder Cards" procedure.

Step 2 Display the TXP_MR_10E_L card in card view.

Step 3 Click the Provisioning > Line > Service-Type tabs.

Step 4 Click the Admin State table cell for the trunk port and choose OOS,DSBLD (ANSI) or Locked,disabled (ETSI) from the drop-down list.

Step 5 Click Apply, then click Yes.

Step 6 Click the Provisioning > Card tabs.

Step 7 In the Wavelength field, choose the first wavelength required by the acceptance test.

Step 8 Click Apply.

Step 9 Click the Provisioning > Line > Service-Type tabs.

Step 10 Click the Admin State table cell for the trunk port and choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list.

Step 11 Click Apply, then click Yes.

Step 12 Connect a power meter to the DWDM TX port. Verify that the output power falls within -4.5 dBm and 1 dBm. If it does not fall within this range, replace the card or contact your next level of support.

Step 13 Repeat Steps 3 through 12 for all the installed TXP cards.

Step 14 Return to your originating procedure (NTP).

DLP-G359 Verify the OPT-BST-L or OPT-AMP-L (OPT-Line Mode) Amplifier Laser and Power


Purpose	This task verifies that the OPT-BST-L or OPT-AMP-L (when provisioned in OPT-Line mode) amplifier laser is on and provisioned to the correct power.
Tools/Equipment	None
Prerequisite Procedures	G46 Log into CTC
Required/As Needed	As needed
Onsite/Remote	Onsite or remote
Security Level	Superuser

Step 1 In node view (single-shelf mode) or shelf view (multishelf mode), double-click the OPT-BST-L or OPT-AMP-L amplifier to display the card view.

Step 2 Click the Maintenance > ALS tabs. If the value in the Currently Shutdown field is NO, continue with Step 3. If not, complete the following steps:

a. Check the OSRI setting. If it is set to On, change it to Off and click Apply.

b. Check the Currently Shutdown field. If it changes to NO, continue with Step 3. If not, contact your next level of support. The amplifier might need to be replaced.

Step 3 Click the Provisioning > Opt Ampli Line > Parameters tabs.

Step 4 Click Reset.

Step 5 Scroll to the right and locate the Signal Output Power parameter for Port 6. Verify that the Signal Output Power value is greater than or equal to 1.5 dBm.

If the Signal Output Power is not greater than or equal to 1.5 dBm, do not continue. Begin troubleshooting or contact your next level of support.

Step 6 Return to your originating procedure (NTP).

DLP-G360 Verify the OPT-AMP-L (OPT-PRE Mode) Amplifier Laser and Power


Purpose	This task verifies that the OPT-AMP-L (when provisioned in OPT-PRE mode) amplifier laser is on and provisioned to the correct power.
Tools/Equipment	None
Prerequisite Procedures	G46 Log into CTC
Required/As Needed	As needed
Onsite/Remote	Onsite or remote
Security Level	Superuser

Step 1 In node view (single-shelf view) or shelf view (multishelf view), double-click the OPT-AMP-L amplifier to display the card view.

Step 2 Click the Maintenance > ALS tabs.

Step 3 If the value shown in the Currently Shutdown field is NO, continue with Step 4. If not, complete the following steps:

a. If the OSRI setting is set to ON, click the table cell and choose OFF from the drop-down list.

b. Click Apply.

Step 4 Click the Provisioning > Opt Ampli Line > Parameters tabs.

Step 5 Locate the Signal Output Power parameter for Port 2. Verify that the Signal Output Power value is greater than or equal to 1.5 dBm. If the optical power is greater than or equal to 1.5 dBm, continue with Step 6. If the optical power is less than 1.5 dBm, check your connections and clean the fibers using the "NTP-G115 Clean Fiber Connectors" procedure. If this does not change the power value, consult your next level of support.

Step 6 Scroll to the right to locate the DCU Insertion Loss parameter. Verify that the DCU Insertion Loss value is less than or equal to 10 dB.

If the optical power is not greater than or equal to 10 dB, do not continue. Begin troubleshooting or contact your next level of support.

Step 7 Return to your originating procedure (NTP).

DLP-G361 Verify the 32DMX-L Power


Purpose	This task verifies that the 32DMX-L card is provisioned to the correct power.
Tools/Equipment	None
Prerequisite Procedures	G46 Log into CTC
Required/As Needed	As needed
Onsite/Remote	Onsite or remote
Security Level	Superuser

Step 1 Display the 32DMX-L card in card view.

Step 2 Click the Provisioning > Optical Chn > Parameters tabs.

Step 3 Change the administrative state for Port 33 to OOS,MT (ANSI) or Locked,maintenance (ETSI)

Step 4 Verify that the VOA Power Ref reaches the provisioned setpoint.

Step 5 (Optional) Connect a power meter to the CHAN TX 01 port through the patch panel. Verify that the physical optical power value coming from drop Port 1 on the west 32DMX card is consistent with the value read (the maximum allowed error is +/- 1 dBm).

Step 6 Change the administrative state for Port 1 to OOS,DSBLD (ANSI) or Locked,disabled (ETSI).

Step 7 Return to your originating procedure (NTP).

NTP-G43 Perform the ROADM Node with 32WSS and 32DMX Cards Acceptance Test


Purpose	This acceptance test verifies that a ROADM node provisioned for C-band wavelengths is operating properly before you connect it to the network. The test verifies that each add/drop and pass-through port on the 32WSS and 32DMX cards operates properly and verifies the operation of the amplifiers. The test also checks the power levels at each transmit and receive port to ensure that power loss in the cabling is within tolerance. If MMU cards are installed, the test verifies that the MMU insertion loss doesn't impact add, drop, or pass through circuits.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_C An optical power meter or optical spectrum analyzer 2 bulk attenuators (10 dB) with LC connectors
Prerequisite Procedures	Chapter 3 "Turn Up a Node"
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note Because the node is isolated and no line-side fibers are connected during the test, the power levels going into the line-side cards will not be the same as the levels after the node is connected to the network. Therefore, if the ROADM shelf does not contain OPT-BST or OPT-BST-E and OPT-PRE amplifiers on both the east and west sides, you must lower the OPT-PRE power thresholds so that it turns on properly. At the end of the test, you will run automatic node setup (ANS) to configure the node with the correct parameters for the network acceptance test.

Note Throughout this procedure, west refers to Slots 1 through 8, and east refers to Slots 10 through 17.

Step 1 Make a copy of Table 4-1 and place it in a convenient location for reference throughout this procedure. The table shows the 32WSS ports and the wavelengths assigned to them. The 32 wavelengths are divided among four physical multi-fiber push on (MPO) connectors on the 32WSS card. Each MPO connector is assigned eight wavelengths. In CTC, the MPO connector appears in the card view Provisioning > Optical Connector tab. Each Optical Connector subtab represents an MPO connector. Ports 1 through 32 are the RX (add) ports; Ports 33 through 64 are the pass-through ports.

Table 4-1 32WSS Ports and Wavelengths Test Checklist
32WSS Provisioning Subtab	Port #	Wavelength
Optical Chn: Optical Connector 1	RX 1, PT 33	1530.33
	RX 2, PT 34	1531.12
	RX 3, PT 35	1531.90
	RX 4, PT 36	1532.68
	RX 5, PT 37	1534.25
	RX 6, PT 38	1535.04
	RX 7, PT 39	1535.82
	RX 8, PT 40	1536.61
Optical Chn: Optical Connector 2	RX 9, PT 41	1538.19
	RX 10, PT 42	1538.98
	RX 11, PT 43	1539.77
	RX 12, PT 44	1540.56
	RX 13, PT 45	1542.14
	RX 14, PT 46	1542.94
	RX 15, PT 47	1543.73
	RX 16, PT 48	1544.53
Optical Chn: Optical Connector 3	RX 17, PT 49	1546.12
	RX 18, PT 50	1546.92
	RX 19, PT 51	1547.72
	RX 20, PT 52	1548.51
	RX 21, PT 53	1550.12
	RX 22, PT 54	1550.92
	RX 23, PT 55	1551.72
	RX 24, PT 56	1552.52
Optical Chn: Optical Connector 4	RX 25, PT 57	1554.13
	RX 26, PT 58	1554.94
	RX 27, PT 59	1555.75
	RX 28, PT 60	1556.55
	RX 29, PT 61	1558.17
	RX 30, PT 62	1558.98
	RX 31, PT 63	1559.79
	RX 32, PT 64	1560.61

Step 2 Complete the "DLP-G46 Log into CTC" task at the ROADM node that you want to test. If you are already logged in, continue with Step 3.

Step 3 Display the ROADM node in node view (single-shelf mode) or multishelf view (multishelf mode).

Step 4 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

Note The OSC terminations created during node turn-up will generate two alarms for each side of the shelf: one an LOS alarm on the OPT-BST or OPT-BST-E card, and the other an LOS alarm on the OSC-CSM or OSCM card. If OSCM cards are installed, SDCC termination failure (EOC) alarms will appear.

Step 5 In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Port Status tabs. Verify that all statuses under Link Status are either Success - Changed, Success - Unchanged, or Not Applicable. If any are not, complete the following steps:

a. Delete the two OSC channels using the "DLP-G186 Delete an OSC Termination" task.

b. Complete the "NTP-G37 Run Automatic Node Setup" procedure.

c. Create the OSC channels using the "NTP-G38 Provision OSC Terminations" procedure.

Step 6 If MMU cards are installed, complete the following steps. If not, continue with Step 7.

a. Display the east MMU in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Click the Admin State table cell for the COM RX, COM TX, EXP RX, and EXP TX ports and choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list.

d. Click Apply, then click Yes to confirm.

e. Display the west MMU in card view.

f. Click the Provisioning > Optical Line > Parameters tabs.

g. Click the Admin State table cell for the COM RX, COM TX, EXP RX, and EXP TX ports and choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list.

Step 7 Display the east 32WSS in card view.

Step 8 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the optical connector number that carries the wavelengths you will test. Refer to Table 4-1, if needed.

Step 9 Click the Admin State table cell for the add port carrying the tested wavelength, then choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list. For example, if the tested wavelength is 1530.33 nm (shown as 1530.3), you would click the Port 1 (CHAN-RX) Admin State field and choose OOS,MT or Locked,maintenance from the drop-down list.

Step 10 Change the administrative state of the pass-through port corresponding to the port in Step 9 to OOS,MT (ANSI) or Locked,maintenance (ETSI). For example, if the tested wavelength is 1530.33 nm (shown as 1530.3), you would click the Port 33 (PASS-THROUGH) Admin State field and choose OOS,MT or Locked,maintenance from the drop-down list. Refer to Table 4-1, if needed.

Step 11 Click Apply, then click Yes to confirm.

Step 12 Repeat Steps 8 through 11 for all wavelengths that you will test.

Step 13 Display the west 32WSS in card view.

Step 14 Repeat Steps 8 through 12 for the west 32WSS card.

Step 15 Display the east 32DMX card in card view and complete the following steps:

a. Choose the Provisioning > Optical Line > Parameters tabs.

b. For Port 33 (COM-RX), click the Admin State table cell and choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list.

c. Click Apply, then click Yes to confirm.

Step 16 Repeat Step 15 for the west 32DMX card.

Step 17 Complete the "DLP-G310 Verify ROADM Node C-Band Pass-Through Channels" task.

Step 18 Complete the following tasks for channels that will be added or dropped on the node.

•G311 Verify the East ROADM C-Band Add/Drop Channels

•G312 Verify the West ROADM C-Band Add/Drop Channels

Step 19 If MMU cards are installed, complete the following steps. If not, continue with Step 20.

a. Display the east MMU in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Click Admin State for the COM RX, COM TX, EXP RX, and EXP TX ports and choose IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) from the drop-down list.

d. Click Apply, then click Yes to confirm.

e. Display the west MMU in card view.

f. Click the Provisioning > Optical Line > Parameters tabs.

g. Click Admin State for the COM RX, COM TX, EXP RX, and EXP TX ports and choose IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) from the drop-down list.

Step 20 Display the east 32WSS in card view.

Step 21 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the optical connector number that carries the wavelengths you tested.

Step 22 Click the Admin State table cell then choose IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) from the drop-down list for all ports that were changed to OOS,MT or Locked,Maintenance in Steps 9 and 10.

Step 23 Click Apply.

Step 24 Repeat Steps 21 through 23 for all the ports that are in OOS,MT or Locked,maintenance state on the east 32WSS card.

Step 25 Display the west 32WSS in card view.

Step 26 Repeat Steps 21 through 24 for all ports on the west 32WSS card.

Step 27 Display the east 32DMX in card view.

Step 28 Choose the Provisioning > Optical Line > Parameters tabs.

Step 29 For Port 33, click the Admin State table cell and choose IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) from the drop-down list.

Step 30 Click Apply.

Step 31 Display the west 32DMX card in card view.

Step 32 Repeat Steps 28 through 30 for the west 32DMX card.

Step 33 Delete both OSC channels using the "DLP-G186 Delete an OSC Termination" task.

Step 34 Complete the "NTP-G37 Run Automatic Node Setup" procedure.

Step 35 Create the two OSC channels using the "NTP-G38 Provision OSC Terminations" procedure.

Step 36 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

b. Verify that no equipment failure alarms appear on the node. If alarms appear, investigate and resolve them before continuing. Refer to the Cisco ONS 15454 DWDM Troubleshooting Guide for procedures.

Stop. You have completed this procedure.

DLP-G310 Verify ROADM Node C-Band Pass-Through Channels


Purpose	This task verifies the signal flow through a ROADM node for C-band pass-through channels. Pass-through channels pass through both 32WSS cards. The channels pass through the first 32WSS from the COM-RX port to the EXP-TX port. In the second 32WSS, the channel goes from the EXP-RX port to the COM-TX port. The channel is not terminated inside the node. If MMU cards are installed, the channel passes through the MMU COM-RX and EXP-TX ports to the 32WSS COM-RX and EXP-TX ports on one side. On the other side, the channel goes from the 32WSS EXP-RX and COM-TX ports to the MMU EXP-RX and COM-TX ports.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_C An optical power meter or optical spectrum analyzer 2 bulk attenuators (10 dB) with LC connectors
Prerequisite Procedures	"DLP-G46 Log into CTC" task
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note Throughout this task, west refers to Slots 1 through 8, and east refers to Slots 10 through 17.

Note This task assumes OSC terminations were created. If not, complete the"NTP-G38 Provision OSC Terminations" procedure before continuing.

Step 1 Create a physical loopback on the west OPT-BST, OPT-BST-E, or OSC-CSM card by connecting the LINE TX port to its LINE RX port. For OPT-BST or OPT-BST-E cards, connect a 10-dB bulk attenuator to the fiber. (OSC-CSM cards do not require attenuation.)

Caution

Failure to use proper attenuation might damage equipment.

Step 2 If an OPT-PRE amplifier is installed on the west side (where the physical loopback was created), perform the following steps. If not, continue with Step 3.

a. Display the OPT-PRE card in card view, then click the Provisioning > Optical Line > Optics Thresholds tabs.

b. Under Types, click Alarm, then click Refresh. The alarm thresholds for the OPT-PRE card will appear.

c. Double-click the Power Failure Low table cell for Port 1 (COM-RX) and delete the current value.

d. Type a new value of -30.0 and press Enter on your computer.

e. On the CTC window, click Apply, then click Yes on the confirmation dialog box.

Step 3 If an OPT-PRE card is installed on the east side, complete the following steps. If an OPT-PRE card is not installed on the east side, continue with Step 4.

a. Display the east OPT-PRE card in card view, then click the Provisioning > Optical Line > Optics Thresholds tabs.

b. Under Types, click Alarm, then click Refresh. The alarm thresholds for the OPT-PRE card will appear.

c. Double-click the Power Failure Low table cell for Port 1 (COM-RX) and delete the current value.

d. Type a new value of -30.0 and press Enter on your computer.

e. On the CTC window, click Apply, then click Yes on the confirmation dialog box.

Step 4 Wait 2 to 3 minutes, then in node view (single-shelf mode) or multishelf view (multishelf mode) click the Alarms tab. Verify that the LOS alarms on the west OSCM or OSC-CSM card and the OPT-BST or OPT-BST-E card have cleared. The clearing of the LOS alarms indicates that the OSC link is active on the west side. If the alarms do not clear, contact your next level of support.

Note A SDCC Termination Failure alarm will continue to appear due to the OSC signal loopback.

Step 5 Display the west 32WSS card in card view.

Step 6 Click the Maintenance tab.

Step 7 Click the Operating Mode table cell for the wavelength under test and choose Pass Through from the drop-down list.

Step 8 Click Apply, then click Yes to confirm.

Step 9 Display the east 32WSS card in card view.

Step 10 Repeat Steps 6 through 8 for the east 32WSS card.

Step 11 If you are using a tunable laser, follow the manufacturer's instructions to complete the following steps. If you are using a TXP_MR_10E_C card, continue with Step 12.

a. Set the output power to a nominal value, such as -3 dBm.

b. Set the tuner to the wavelength you will test, then continue with Step 13.

Step 12 If you are using a TXP_MR_10E_C card, complete the "DLP-G268 Provision TXP_MR_10E_C Cards for Acceptance Testing" task for the TXP containing the wavelength you will test.

Step 13 Connect the tunable laser transmitter or the TXP_MR_10E_C card DWDM TX port to the east OPT-BST, OPT-BST-E, or OSC-CSM LINE RX port. If an east OPT-PRE is installed, insert a 10-dB attenuator on the fiber coming from the TXP_MR_10E_C card.

Caution

Failure to use proper attenuation might damage equipment.

Step 14 If an OPT-PRE card is installed on the east side, complete the following steps. If not, continue with Step 15.

a. Display the east OPT-PRE in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power parameter for Port 1 (COM-RX). Record the value.

d. Display the east OPT-BST, OPT-BST-E, or OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Locate the Power value for Port 2 (COM-TX) (OPT-BST or OPT-BST-E) or Port 3 (COM-TX) (OSC-CSM). Verify that the value matches the power recorded in Step c, +/- 2.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-PRE card and the OPT-BST, OPT-BST-E, or OSC-CSM card. Check the values again. If they still do not match, contact your next level of support.

g. For the east OPT-PRE card, complete the "DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task.

Step 15 If an MMU card is installed on the east side, complete the following steps, then continue with Step 17. If an MMU card is not installed, continue with Step 16.

a. Display the east MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 3 (COM-RX) power parameter. Record the value.

d. If an east OPT-PRE card is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the OPT-PRE Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an east OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

i. Verify that value in the Step e, g, or h matches the power recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the MMU card and the OPT-BST, OPT-BST-E, OPT-PRE, or OSC-CSM cards. Check the values again. If they still do not match, contact your next level of support.

j. Display the east MMU card in card view.

k. Click the Provisioning > Optical Line > Parameters tabs.

l. Record the value in the Power table cell for Port 2(EXP-TX) of the east MMU card.

m. Display the east 32WSS card in card view.

n. Click the Provisioning > Optical Line > Parameters tabs.

o. Verify that the value in the Power table cell for Port 68 (COM-RX) is equal to the value recorded in Step l, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS and MMU cards. Check the values again. If they still do not match, contact your next level of support.

p. Continue with Step 17.

Step 16 Verify the east 32WSS to OPT-BST, OPT-PRE, or OSC-CSM cable connection:

a. Display the east 32WSS in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If an east OPT-PRE card is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an OPT-BST or OPT-BST-E card is installed on the east side, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

i. Verify that the value in Step e, g, or h matches the power recorded in Step c, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS card and the OPT-PRE, OPT-BST, OPT-BST-E, or OSC-CSM card. Check the values again. If they still do not match, contact your next level of support.

Step 17 Verify the EXPRESS cable connection between the two 32WSS cards:

a. Display the east 32WSS in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 65 (EXP-TX) Power parameter. Record the value.

a. Display the west 32WSS in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power value for EXPRESS Port 66 (EXP-RX). Verify that the value matches the power recorded in Step c, +/-1 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS cards. Check the values again. If they still do not match, contact your next level of support.

Step 18 Display the west 32WSS card in card view.

Step 19 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the connector number containing the wavelength you are testing. Refer to Table 4-1, if needed.

Step 20 Wait 60 to 70 seconds (or click Reset), then locate the Power and VOA Power Ref parameters for the tested PASS-THROUGH port. Verify that the Power value is equal to the VOA Power Ref value, +/- 1.5 dBm. If the Power value is not equal to the VOA Power Ref value +/-1.5 dBm, contact your next level of support.

Step 21 If an MMU card is installed on the west side, complete the following steps. If an MMU card is not installed on the west side, continue with Step 22.

a. Display the west 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67(COM-TX).

d. Display the west MMU card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port 1(EXP-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS and MMU cards. Check the values again. If they still do not match, contact your next level of support.

g. Record the value in the Power table cell for Port 4 (COM-TX).

h. If a west OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step i. If not, continue with Step j.

i. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step k.

j. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step k.

k. Verify that the value in Step i or j matches the power recorded in Step g, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST, OPT-BST-E, or OSC-CSM and MMU cards. Check the values again. If they still do not match, contact your next level of support.

l. Continue with Step 23.

Step 22 If an OPT-BST, OPT-BST-E, or OSC-CSM card is installed on the west side, complete the following steps. If not, continue with Step 23.

a. Display the west OPT-BST, OPT-BST-E, or OSC-CSM in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 1 (COM-RX) Power parameter (OPT-BST or OPT-BST-E cards) or the Port 2 (COM-RX) Power parameter (OSC-CSM cards). Record the value.

d. Display the west 32WSS in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Locate the Power value for Port 67 (COM-TX). Verify that the value matches the power recorded in Step c, +/-1 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST, OPT-BST-E, or OSC-CSM card and the 32WSS card. Check the values again. If they still do not match, contact your next level of support.

g. For the west OPT-BST or OPT-BST-E card, complete the "DLP-G79 Verify the OPT-BST, OPT-BST-E, or OPT-BST-L Amplifier Laser and Power" task.

Step 23 If a OPT-PRE card is installed on the west side, complete the following steps. If not, continue with Step 24.

a. Display the west OPT-PRE in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 1 (COM-RX) Power parameter. Record the value.

d. Display the west OPT-BST, OPT-BST-E, or OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

g. For the west OPT-PRE, complete the "DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task.

Step 24 If an MMU card is installed on the west side, complete the following steps, then continue with Step 26. If an MMU card is not installed on the west side, continue with Step 25.

a. Display the west MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 3 (COM-RX) power parameter. Record the value.

d. If an west OPT-PRE card is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the OPT-PRE Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an west OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

j. Display the east MMU card in card view.

k. Click the Provisioning > Optical Line > Parameters tabs.

l. Record the value in the Power table cell for Port 2(EXP-TX) of the west MMU card.

m. Display the west 32WSS card in card view.

n. Click the Provisioning > Optical Line > Parameters tabs.

o. Verify that the value in the Power table cell for Port 68 (COM-RX) is equal to the value recorded in Step l, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS and cards and the MMU cards. Check the values again. If they still do not match, contact your next level of support.

p. Continue with Step 26.

Step 25 Verify the west 32WSS card to OPT-BST, OPT-BST-E, OPT-PRE, or OSC-CSM card cable connection:

a. Display the west 32WSS in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If a west OPT-PRE card is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an west OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

Step 26 Verify the EXPRESS cable connection between the two 32WSS cards:

a. Display the west 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 65 (EXP-TX) Power parameter. Record the value.

a. Display the east 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power value for Port 66 (EXP-RX). Verify that the value matches the power recorded in Step c, +/- 1 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS cards. Check the values again. If they still do not match, contact your next level of support.

Step 27 Display the east 32WSS card in card view.

Step 28 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the connector number containing the wavelength you are testing. Refer to Table 4-1, if needed.

Step 29 Wait 60 to 70 seconds (or click Reset), then locate the Power and VOA Power Ref parameters for the tested PASS-THROUGH port. Verify that the Power value is equal to the VOA Power Ref value, +/- 1.5 dBm. If the Power value is not equal to the VOA Power Ref value +/- 1.5 dBm, consult your next level of support.

Step 30 If an MMU card is installed on the east side, complete the following steps. If an MMU card is not installed on the east side, continue with Step 31.

a. Display the east 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67(COM-TX).

d. Display the east MMU card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

g. Record the value in the Power table cell for Port 4 (COM-TX).

h. If a east OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step i. If not, continue with Step j.

i. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step k.

j. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step k.

l. Continue with Step 32.

Step 31 If an OPT-BST, OPT-BST-E, or OSC-CSM card is installed on the east side, complete the following steps. If not, continue with Step 32.

a. Display the east OPT-BST, OPT-BST-E, or OSC-CSM card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 1 (COM-RX) Power parameter (OPT-BST or OPT-BST-E cards) or the Port 2 (COM-RX) Power parameter (OSC-CSM cards). Record the value.

d. Display the east 32WSS card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Locate the Power value for Port 67 (COM-TX). Verify that the value matches the power recorded in Step c, +/-1 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST, OPT-BST-E, or OSC-CSM and 32WSS cards. Check the values again. If they still do not match, contact your next level of support.

g. For the east OPT-BST or OPT-BST-E card, complete the "DLP-G79 Verify the OPT-BST, OPT-BST-E, or OPT-BST-L Amplifier Laser and Power" task.

Step 32 Complete Steps 18, 19, 27, and 28 for the additional wavelengths that you want to test. If you have tested all the wavelengths, continue with Step 33.

Step 33 Display the east 32WSS card in card view.

Step 34 Click the Maintenance tab.

Step 35 Under Operating Mode, click the table cell and choose Not Assigned from the drop-down list for all wavelengths.

Step 36 Click Apply, then click Yes to confirm.

Step 37 Display the west 32WSS card in card view.

Step 38 Repeat Steps 34 through 36 for the west 32WSS card.

Step 39 Disconnect the TXP or tunable laser from the east OPT-BST, OPT-BST-E, or OSC-CSM line side RX ports.

Step 40 Remove the loopback fiber from the line RX and TX in the west OPT-BST, OPT-BST-E, or OSC-CSM card.

Step 41 Return to your originating procedure (NTP).

DLP-G311 Verify the East ROADM C-Band Add/Drop Channels


Purpose	This procedure verifies the signal flow through the east side of a ROADM node for C-band add/drop channels.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_C An optical power meter or optical spectrum analyzer 2 bulk attenuators (10 dB) with LC connectors
Prerequisite Procedures	G46 Log into CTC
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note Throughout this task, west refers to Slots 1 through 8, and east refers to Slots 10 through 17.

Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), display the Alarms tab.

Step 2 Create a physical loopback on the east OPT-BST, OPT-BST-E, or OSC-CSM card by connecting the LINE TX port to its LINE RX port. For OPT-BST or OPT-BST-E cards, connect a 10-dB bulk attenuator to the fiber. (OSC-CSM cards do not require attenuation.)

Caution

Failure to use proper attenuation might damage equipment.

Step 3 Wait 2 to 3 minutes, then click the Alarms tab. Verify that the LOS alarms on the east OSCM or OSC-CSM card and the OPT-BST or OPT-BST-E card have cleared. The clearing of the LOS alarms indicates that the OSC link is active on the east side.

Note A SDCC Termination Failure alarm will continue to appear due to the OSC signal loopback.

Step 4 If you are using a tunable laser, follow the manufacturer's instructions to complete the following steps. If you are using a TXP_MR_10E_C card, continue with Step 5.

a. Set the output power to a nominal value, such as -3 dBm.

b. Set the tuner to the wavelength you are testing, then continue with Step 7.

Step 5 If you are using a TXP_MR_10E_C card, complete the "DLP-G268 Provision TXP_MR_10E_C Cards for Acceptance Testing" task for the TXP containing the wavelength you will test. Refer to Table 4-1, if needed.

Step 6 If you are using a TXP_MR_10E_C card, complete the following steps. If you are using a tunable laser continue with Step 7.

a. Display the TXP_MR_10E_C in card view.

b. Click the Performance > Optics PM > Current Values tabs.

c. Locate the Port 2 (Trunk) table cell for the TX Optical Pwr parameter. Record the value.

Step 7 Connect the tunable laser transmitter or the TXP_MR_10E_C card DWDM TX port to the east side fiber patch panel MUX port that is connected to the east 32WSS card CHAN RX port carrying the tested wavelength. (If the TXP_MR_10E_C card was installed during Chapter 3 "Turn Up a Node," simply verify the cable connection.)

Step 8 Connect the TXP_MR_10E_C DWDM RX port or the power meter RX port to the east side fiber patch panel DMX port that is connected with the east 32DMX card CHAN-TX port carrying the tested wavelength. (If the TXP_MR_10E_C card was installed during Chapter 3 "Turn Up a Node," simply verify the cable connection.)

Step 9 Display the 32WSS card in card view.

Step 10 Click the Maintenance tab.

Step 11 For each wavelength that you will test, click the table cell under Operating Mode and choose Add Drop from the drop-down list.

Step 12 Click Apply and then Yes, to confirm.

Step 13 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the optical connector number that carries the wavelengths you will test. Refer to Table 4-1, if needed.

Step 14 Find the tested wavelength CHAN RX port, then scroll to the right until you see the Power Add parameter. Verify that the Power Add value for the tested port CHAN RX is equal to the output power level of the tunable laser or the TXP_MR_10E_C card measured in Step 6 +/- 1 dBm.

Step 15 Click the Provisioning > Optical Line > Parameters tabs and record the value in the Power table cell for Port 67 (COM-TX) for the wavelength under test.

Step 16 Verify that the power value from Step 15 reaches the EastSide.Tx.Power.Add&Drop - Output Power set +/- 1 dBm. To view this setpoint:

a. In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Provisioning tabs.

b. In the Selector window on the left, expand the East Side parameters tree view.

c. Expand the TX category.

d. Expand the Power category, then highlight Add&Drop - Output Power.

e. View the EastSide.TxPower.Add&Drop - Output Power parameter on the right pane.

f. If the power value does not match the value recorded in Step 15, +/- 2dBm, contact your next level of support.

Step 17 If an MMU card is installed on the east side, complete the following steps. If an MMU card is not installed on the east side, continue with Step 18.

a. Display the east 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. Display the east MMU card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port 1(EXP-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure on page 13-25 to clean the fiber connection between the 32WSS and MMU cards. Check the values again. If they still do not match, contact your next level of support.

g. Record the value in the Power table cell for Port 4 (COM-TX).

h. If a east OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step i. If not, continue with Step j.

i. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step k.

j. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step k.

l. Continue with Step 19.

Step 18 Verify the connection between the 32WSS and OPT-BST, OPT-BST-E or OSC_CSM cards:

a. Display the east 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. If a OPT-BST or OPT-BST-E card is installed on the east side, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step g.

f. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step g.

g. Verify that the value in Step e or f matches the power recorded in Step c, +/- 1.0 dB. If so, continue with Step 19. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST, OPT-BST-E, or OSC-CSM and 32WSS cards. Check the values again. If they still do not match, contact your next level of support.

Step 19 If an OPT-PRE card is installed on the east side, complete the following steps. If not, continue with Step 20.

a. Display the east OPT-PRE in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power parameter for Port 1 (COM-RX). Record the value.

d. Display the east OPT-BST, OPT-BST-E, or OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Locate the Port 2 (COM-TX) Power value (for OPT-BST or OPT-BST-E cards) or Port 3 (COM-TX) Power value (for OSC-CSM card). Verify that the value matches the power recorded in Step c, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-PRE card and the OPT-BST, OPT-BST-E, or OSC-CSM card. Check the values again. If they still do not match, contact your next level of support.

g. For the east OPT-PRE card, complete the "DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task.

Step 20 If an MMU card is installed on the east side, complete the following steps. If an MMU card is not installed on the east side, continue with Step 21.

a. Display the east MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If an OPT-PRE card is installed on the east side, display it in card view and complete Step e. If not, continue with Step f.

e. Click the OPT-PRE Provisioning > Opt.Ampli.Line > Parameters tabs. Record the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an east OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

i. Verify that value in the Step e, g, or h matches the power recorded in Step e, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the MMU card and the OPT-BST, OPT-BST-E, or OSC-CSM cards. Check the values again. If they still do not match, contact your next level of support.

j. Display the east MMU card in card view.

k. Click the Provisioning > Optical Line > Parameters tabs.

l. Record the value in the Power table cell for Port 2 (EXP-TX).

m. Display the east 32WSS card in card view.

n. Click the Provisioning > Optical Line > Parameters tabs.

p. Continue with Step 22.

Step 21 Verify the connection between the east 32WSS card and the OPT-BST, OPT-BST-E, OPT-PRE, or OSC-CSM card:

a. Display the east 32WSS in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If an east OPT-PRE card is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an east OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the east OSC-CSM card in card view. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

Step 22 Verify the east 32WSS and 32DMX connection:

a. Display the east 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs, and record the value in the Power table cell for Port 69 (DROP-TX).

c. Display the east 32DMX card in card view.

d. Click the Provisioning > Optical Line > Parameters tabs. Record the value in the Port 33 (COM-RX) table cell. Verify that the value is equal to the value recorded in b., +/- 1 dBm. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS and 32DMX cards. Check the values again. If they still do not match, contact your next level of support.

Step 23 Display the east 32DMX card in card view.

Step 24 Click the Provisioning > Optical Chn > Parameters tab. Record the CHAN-TX port value under the Power parameter for the wavelength under test.

Step 25 Verify that the power value from Step 24 reaches the EastSide.Rx.Power.Add&Drop - Drop Power setpoint +/- 2 dBm. To view this setpoint:

a. Go to node view (single-shelf mode) or multishelf view (multishelf mode) and click the Provisioning > WDM-ANS > Provisioning tabs.

b. In the Selector window on the left, expand the East Side parameters tree view.

c. Expand the RX category.

d. Expand the Power category, then highlight Add&Drop - Drop Power.

e. View the EastSide.Rx.Power.Add&Drop - Drop Power parameter on the right pane.

f. If the power value does not match the value recorded in Step 24 (+/- 2 dBm), contact your next level of support.

Step 26 If you are using a TXP_MR_10E_C card, display it in card view. If not, read the values called for in Step 28 on the optical test set or tunable laser you are using.

Step 27 Click the Performance > Optics PM > Current Values tabs.

Step 28 In the Port 2 (Trunk) column, locate the RX Optical Power value. Verify that the value matches the power in Step 24, +/- 2 dBm. If the power values do not match (+/- 2 dBm), complete the following steps:

a. Remove, clean, and replace the cable connecting the TXP_MR_10E_C RX port to the east fiber patch panel DMX port for the tested wavelength. See the "NTP-G115 Clean Fiber Connectors" procedure.

b. Repeat this step. If the power values still do not match (+/- 2 dBm) contact your next level of support.

Step 29 Repeat Steps 4 through 28 for the remaining wavelengths.

Step 30 Display the east 32WSS card in card view.

Step 31 Click the Maintenance tab.

Step 32 Click the table cell under Operating Mode and choose Not Assigned from the drop-down list for all wavelengths.

Step 33 Click Apply, then click Yes to confirm.

Step 34 Disconnect the TXP or tunable laser from the east side patch panel.

Step 35 Unplug the physical loopback fiber from the line TX and RX in the OPT-BST, OPT-BST-E, or OSC-CSM card.

Step 36 Return to your originating procedure (NTP).

DLP-G312 Verify the West ROADM C-Band Add/Drop Channels


Purpose	This procedure verifies the signal flow through the west side of an ROADM node for C-band add/drop channels.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_C An optical power meter or optical spectrum analyzer 2 bulk attenuators (10 dB) with LC connectors
Prerequisite Procedures	"DLP-G46 Log into CTC" task
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note Throughout this task, west refers to Slots 1 through 8, and east refers to Slots 10 through 17.

Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), display the Alarms tab.

Step 2 Create a physical loopback on the west OPT-BST, OPT-BST-E, or OSC-CSM card by connecting the LINE TX port to its LINE RX port. For OPT-BST or OPT-BST-E cards, connect a 10-dB bulk attenuator to the fiber. (OSC-CSM cards do not require attenuation.)

Caution

Failure to use proper attenuation might damage equipment.

Step 3 Wait 2 to 3 minutes, then click the Alarms tab. Verify that the LOS alarms on the west OSCM or OSC-CSM card and the OPT-BST or OPT-BST-E card have cleared. The clearing of the LOS alarms indicates that the OSC link is active on the west side.

Note A SDCC Termination Failure alarm will continue to appear due to the OSC signal loopback.

Step 4 If you are using a tunable laser, follow the manufacturer's instructions to complete the following steps. If you are using a TXP_MR_10E_C card, continue with Step 5.

a. Set the output power to a nominal value, such as -3 dBm.

b. Set the tuner to the wavelength you are testing, then continue with Step 7.

Step 6 If you are using a TXP_MR_10E_C card, complete the following steps. If you are using a tunable laser continue with Step 7.

a. Display the TXP_MR_10E_C in card view.

b. Click the Performance > Optics PM > Current Values tabs.

c. Locate the Port 2 (Trunk) table cell for the TX Optical Pwr parameter. Record the value.

Step 7 Connect the tunable laser transmitter or the TXP_MR_10E_C card DWDM TX port to the west side fiber patch panel MUX port that is connected to the west 32WSS card CHAN RX port carrying the tested wavelength. (If the TXP_MR_10E_C card was installed during Chapter 3 "Turn Up a Node," simply verify the cable connection.)

Step 8 Connect the TXP_MR_10E_C DWDM RX port or the power meter RX port to the west side fiber patch panel DMX port that is connected with the west 32DMX card CHAN-TX port carrying the tested wavelength. (If the TXP_MR_10E_C card was installed during Chapter 3 "Turn Up a Node," simply verify the cable connection.)

Step 9 Display the 32WSS card in card view.

Step 10 Click the Maintenance tab.

Step 11 For each wavelength that you will test, click the table cell under Operating Mode and choose Add Drop from the drop-down list.

Step 12 Click Apply and then Yes, to confirm.

Step 15 Click the Provisioning > Optical Line > Parameters tabs and record the value in the Power table cell for Port 67 (COM-TX) for the wavelength under test.

Step 16 Verify that the power value from Step 15 reaches the WestSide.Tx.Power.Add&Drop - Output Power set +/- 1 dBm. To view this setpoint:

a. In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Provisioning tabs.

b. In the Selector window on the left, expand the West Side parameters tree view.

c. Expand the TX category.

d. Expand the Power category, then highlight Add&Drop - Output Power.

e. View the WestSide.TxPower.Add&Drop - Output Power parameter on the right pane.

f. If the power value does not match the value recorded in Step 15, +/- 2dBm, contact your next level of support.

Step 17 If an MMU card is installed on the west side, complete the following steps. If an MMU card is not installed on the west side, continue with Step 18.

a. Display the west 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. Display the west MMU card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

g. Record the value in the Power table cell for Port 4 (COM-TX).

h. If a west OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step i. If not, continue with Step j.

i. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step k.

j. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step k.

l. Continue with Step 19.

Step 18 Verify the connection between the 32WSS and OPT-BST, OPT-BST-E or OSC_CSM cards:

a. Display the west 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. If a OPT-BST or OPT-BST-E card is installed on the west side, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step g.

f. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step g.

Step 19 If an OPT-PRE card is installed on the west side, complete the following steps. If not, continue with Step 20.

a. Display the west OPT-PRE in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power parameter for Port 1 (COM-RX). Record the value.

d. Display the west OPT-BST, OPT-BST-E, or OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

g. For the west OPT-PRE card, complete the "DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task.

Step 20 If an MMU card is installed on the west side, complete the following steps. If an MMU card is not installed on the west side, continue with Step 21.

a. Display the west MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If an OPT-PRE card is installed on the west side, display it in card view and complete Step e. If not, continue with Step f.

e. Click the OPT-PRE Provisioning > Opt.Ampli.Line > Parameters tabs. Record the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an west OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

j. Display the west MMU card in card view.

k. Click the Provisioning > Optical Line > Parameters tabs.

l. Record the value in the Power table cell for Port 2 (EXP-TX).

m. Display the west 32WSS card in card view.

n. Click the Provisioning > Optical Line > Parameters tabs.

p. Continue with Step 22.

Step 21 Verify the connection between the west 32WSS card and the OPT-BST, OPT-BST-E, OPT-PRE, or OSC-CSM card:

a. Display the west 32WSS in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If a west OPT-PRE card is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an west OPT-BST or OPT-BST-E card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the west OSC-CSM card in card view. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

Step 22 Verify the west 32WSS and 32DMX connection:

a. Display the west 32WSS card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs, and record the value in the Power table cell for Port 69 (DROP-TX).

c. Display the west 32DMX card in card view.

d. Click the Provisioning > Optical Line > Parameters tabs. Record the value in the Port 2 (COM-RX) table cell. Verify that the value is equal to the value recorded in b, +/- 1 dBm. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS and 32DMX cards. Check the values again. If they still do not match, contact your next level of support.

Step 23 Display the west 32DMX card in card view.

Step 24 Click the Provisioning > Optical Chn > Parameters tab. Record the CHAN-TX port value under the Power parameter for the wavelength under test.

Step 25 Verify that the power value from Step 24 reaches the WestSide.Rx.Power.Add&Drop - Drop Power setpoint +/- 2 dBm. To view this setpoint:

a. Go to node view (single-shelf mode) or multishelf view (multishelf mode) and click the Provisioning > WDM-ANS > Provisioning tabs.

b. In the Selector window on the left, expand the West Side parameters tree view.

c. Expand the RX category.

d. Expand the Power category, then highlight Add&Drop - Drop Power.

e. View the WestSide.Rx.Power.Add&Drop - Drop Power parameter on the right pane.

f. If the power value does not match the value recorded in Step 24 (+/- 2 dBm), contact your next level of support.

Step 26 Display the TXP_MR_10E_C card in card view.

Step 27 Click the Performance > Optics PM > Current Values tabs.

a. Remove, clean, and replace the cable connecting the TXP_MR_10E_C RX port to the west fiber patch panel DMX port for the tested wavelength. See the "NTP-G115 Clean Fiber Connectors" procedure.

b. Repeat this step. If the power values still do not match (+/- 2 dBm) contact your next level of support.

Step 29 Repeat Steps 4 through 28 for the remaining wavelengths.

Step 30 Display the west 32WSS card in card view.

Step 31 Click the Maintenance tab.

Step 32 Click the table cell under Operating Mode and choose Not Assigned from the drop-down list for all wavelengths.

Step 33 Click Apply, then click Yes to confirm.

Step 34 Disconnect the TXP or tunable laser from the west side patch panel.

Step 35 Unplug the physical loopback fiber from the line TX and RX in the OPT-BST, OPT-BST-E, or OSC-CSM card.

Step 36 Return to your originating procedure.

NTP-G154 Perform the ROADM Node with 32WSS-L and 32DMX-L Cards Acceptance Test


Purpose	This acceptance test verifies that a ROADM node provisioned for L-band wavelengths is operating properly before you connect it to the network. The test verifies that each add/drop and pass-through port on the 32WSS-L and 32DMX-L card operates properly and verifies the operation of the amplifiers. The test also checks the power levels at each transmit and receive port to ensure that power loss in the cabling is within tolerance. If MMU cards are installed, the test verifies that the MMU insertion loss doesn't impact add, drop, or pass through traffic.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_L An optical power meter or optical spectrum analyzer 2 bulk attenuators (10 dB) with LC connectors
Prerequisite Procedures	Chapter 3 "Turn Up a Node"
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note Because the node is isolated and no line-side fibers are connected during the test, the power levels going into the line-side components will not be the same as they would be in a real network setup. Therefore, if the ROADM shelf does not contain OPT-BST-L and OPT-AMP-L (provisioned in OPT-PRE mode) amplifiers on both the east and west sides, you must lower the OPT-AMP-L power thresholds so that it turns on properly. At the end of the test, you will run ANS to configure the node with the correct parameters for the network acceptance test.

Step 1 Make a copy of Table 4-2 and place it in a convenient location for reference throughout this procedure. The table shows the 32WSS-L ports and the wavelengths assigned to them. The 32 wavelengths are divided among four physical multi-fiber push on (MPO) connectors on the 32WSS-L card. Each MPO connector is assigned eight wavelengths. In CTC, the MPO connector appears in the card view Provisioning > Optical Connector tab. Each Optical Connector subtab represents an MPO connector. Ports 1 through 32 are the channel RX (add) ports; Ports 33 through 64 are the Pass-Through ports.

Table 4-2 32WSS-L Ports and Wavelengths Test Checklist
32WSS-L Provisioning Subtab	Port #	Wavelength
Optical Chn: Optical Connector 1	RX 1, PT 33	1577.86
	RX 2, PT 34	1578.69
	RX 3, PT 35	1579.52
	RX 4, PT 36	1580.35
	RX 5, PT 37	1581.18
	RX 6, PT 38	1582.02
	RX 7, PT 39	1582.85
	RX 8, PT 40	1583.69
Optical Chn: Optical Connector 2	RX 9, PT 41	1584.53
	RX 10, PT 42	1585.36
	RX 11, PT 43	1586.20
	RX 12, PT 44	1587.04
	RX 13, PT 45	1587.88
	RX 14, PT 46	1588.73
	RX 15, PT 47	1589.57
	RX 16, PT 48	1590.41
Optical Chn: Optical Connector 3	RX 17, PT 49	1591.26
	RX 18, PT 50	1592.10
	RX 19, PT 51	1592.95
	RX 20, PT 52	1593.79
	RX 21, PT 53	1594.64
	RX 22, PT 54	1595.49
	RX 23, PT 55	1596.34
	RX 24, PT 56	1597.19
Optical Chn: Optical Connector 4	RX 25, PT 57	1598.04
	RX 26, PT 58	1598.89
	RX 27, PT 59	1599.75
	RX 28, PT 60	1600.60
	RX 29, PT 61	1601.46
	RX 30, PT 62	1602.31
	RX 31, PT 63	1603.17
	RX 32, PT 64	1604.03

Step 2 Complete the "DLP-G46 Log into CTC" task at the ROADM node that you want to test. If you are already logged in, continue with Step 3.

Step 3 Display the ROADM node in node view (single-shelf mode) or multishelf view (multishelf mode).

Step 4 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

Note The OSC terminations created during node turn-up will generate two alarms for each side of the shelf, one for an LOS on the OPT-BST-L card, and the other for an LOS on the OSC-CSM or OSCM card. If OSCM cards are installed, SDCC termination failure (EOC) alarms will appear.

Step 5 In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Port Status tabs. Verify that all statuses under Link Status are listed as Success - Changed, Success - Unchanged, or Not Applicable. If any are not, complete the following steps:

a. Delete the two OSC channels using the "DLP-G186 Delete an OSC Termination" task.

b. Complete the "NTP-G37 Run Automatic Node Setup" procedure.

c. Create the OSC channels using the "NTP-G38 Provision OSC Terminations" procedure.

Step 6 If MMU cards are installed, complete the following steps. If not, continue with Step 7.

a. Display the east MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Click the Admin State table cell for the COM RX, COM TX, EXP RX, and EXP TX ports and choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list.

d. Click Apply, then click Yes to confirm.

e. Display the west MMU card in card view.

f. Click the Provisioning > Optical Line > Parameters tabs.

g. Click the Admin State table cell for the COM RX, COM TX, EXP RX, and EXP TX ports and choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list.

Step 7 Display the east 32WSS-L in card view.

Step 10 Change the administrative state of the pass-through port corresponding to the port in Step 9 to OOS,MT (ANSI) or Locked,maintenance (ETSI). For example, if the tested wavelength is 1577.86 nm (shown as 1577.8), you would click the Port 33 (PASS-THROUGH) Admin State field and choose OOS,MT or Locked,maintenance from the drop-down list. Refer to Table 4-2, if needed.

Step 11 Click Apply, then click Yes to confirm.

Step 12 Repeat Steps 8 through 11 for all wavelengths that you will test.

Step 13 Display the west 32WSS-L in card view.

Step 14 Repeat Steps 8 through 12 for the west 32WSS-L card.

Step 15 Display the east 32DMX-L in card view and complete the following steps:

a. Choose the Provisioning > Optical Line > Parameters tabs.

b. For Port 33 (COM-RX), click the Admin State table cell and choose OOS,MT (ANSI) or Locked,maintenance (ETSI) from the drop-down list.

c. Click Apply, then click Yes to confirm.

Step 16 Repeat Step 15 for the west 32DMX-L card.

Step 17 Complete the "DLP-G362 Verify ROADM Node L-Band Pass-Through Channels" task.

Step 18 Complete the following tasks for channels that will be added or dropped on the node.

•G363 Verify the East ROADM L-Band Add/Drop Channels

•G364 Verify the West ROADM L-Band Add/Drop Channels

Step 19 If MMU cards are installed, complete the following steps. If not, continue with Step 20.

a. Display the east MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Click the Admin State table cell for the COM RX, COM TX, EXP RX, and EXP TX ports and choose IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) from the drop-down list.

d. Click Apply, then click Yes to confirm.

e. Display the west MMU card in card view.

f. Click the Provisioning > Optical Line > Parameters tabs.

g. Click the Admin State table cell for the COM RX, COM TX, EXP RX, and EXP TX ports and choose IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) from the drop-down list.

Step 20 Display the east 32WSS-L in card view.

Step 21 Click the Provisioning > Optical Chn Optical Connectorn > Parameters tabs, where n = the optical connector number that carries the wavelengths you tested.

Step 23 Click Apply.

Step 24 Repeat Steps 21 through 23 for all the ports that are OOS,MT or Locked,maintenance on the east 32WSS-L card.

Step 25 Display the west 32WSS-L in card view.

Step 26 Repeat Steps 21 through 24 for all ports on the west 32WSS-L card.

Step 27 Display the east 32DMX-L in card view.

Step 28 Choose the Provisioning > Optical Line > Parameters tabs.

Step 29 For Port 33, click the Admin State table cell and choose IS,AINS (ANSI) or Unlocked,automaticInService (ETSI) from the drop-down list.

Step 30 Click Apply.

Step 31 Display the west 32DMX-L card in card view.

Step 32 Repeat Steps 28 through 30 for the west 32DMX-L card.

Step 33 Delete both OSC channels using the "DLP-G186 Delete an OSC Termination" task.

Step 34 Complete the "NTP-G37 Run Automatic Node Setup" procedure.

Step 35 Create the two OSC channels using the "NTP-G38 Provision OSC Terminations" procedure.

Step 36 Click the Alarms tab.

a. Verify that the alarm filter is not on. See the "DLP-G128 Disable Alarm Filtering" task as necessary.

Stop. You have completed this procedure.

DLP-G362 Verify ROADM Node L-Band Pass-Through Channels


Purpose	This task verifies the signal flow through a ROADM node for L-band pass-through channels. Configuring a channel pass-through mode means that the channel passes through both 32WSS-L cards. The channel passes through the first 32WSS-L from the COM RX port to the EXP TX port. In the second 32WSS-L, the channel goes from the EXP RX port to the COM TX port. The channel is not terminated inside the node. If MMU cards are installed, the channel passes through the MMU COM RX and EXP TX ports to the 32WSS-L COM RX and EXP TX ports on one side. On the other side, the channel goes from the 32WSS-L EXP RX and 32WSS-L COM TX ports to the MMU EXP RX and COM TX.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_L An optical power meter or optical spectrum analyzer 2 bulk attenuators (10 dB) with LC connectors
Prerequisite Procedures	"DLP-G46 Log into CTC" task
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note Throughout this task, west refers to Slots 1 through 8, and east refers to Slots 10 through 17.

Step 1 Create a physical loopback on the west OPT-BST-L or OSC-CSM card by connecting the LINE TX port to its LINE RX port. For OPT-BST-L cards, connect a 10-dB bulk attenuator to the fiber. (OSC-CSM cards do not require attenuation.)

Caution

Failure to use proper attenuation might damage equipment.

Step 2 If an OPT-AMP-L (provisioned in OPT-PRE mode) amplifier is installed on the west side (where the physical loopback was created), perform the following steps. If not, continue with Step 3.

a. Display the OPT-AMP-L card in card view, then click the Provisioning > Optical Line > Optics Thresholds tabs.

b. Under Types, click Alarm, then click Refresh. The alarm thresholds for the OPT-AMP-L will appear.

c. Double-click the Power Failure Low table cell for Port 1 (1-Line-2-1 RX) and delete the current value.

d. Type a new value of -30. Press Enter on your computer,

e. On the CTC window, click Apply, then click Yes on the confirmation dialog box.

Step 3 If an OPT-AMP-L (provisioned in OPT-PRE mode) amplifier is installed on the east side (where the physical loopback was created), perform the following steps. If not, continue with Step 4.

a. Display the OPT-AMP-L card in card view, then click the Provisioning > Optical Line > Optics Thresholds tabs.

b. Under Types, click Alarm, then click Refresh. The alarm thresholds for the OPT-AMP-L will appear.

c. Double-click the Power Failure Low table cell for Port 1 (1-Line-2-1 RX) and delete the current value.

d. Type a new value of -30. Press Enter on your computer,

e. On the CTC window, click Apply, then click Yes on the confirmation dialog box.

Step 4 Wait 2 to 3 minutes, then in node view (single-shelf mode) or multishelf view (multishelf mode) click the Alarms tab. Verify that the LOS alarms on the west OSCM or OSC-CSM card and the OPT-BST-L card have cleared. The clearing of the LOS alarms indicates that the OSC link is active on the west side. If the alarms do not clear, contact your next level of support.

Note A SDCC Termination Failure alarm will continue to appear due to the OSC signal loopback.

Step 5 Display the west 32WSS-L card in card view.

Step 6 Click the Maintenance tab.

Step 7 Click the Operating Mode table cell and choose Pass Through from the drop-down list.

Step 8 Click Apply, then click Yes to confirm.

Step 9 Display the east 32WSS-L card in card view.

Step 10 Repeat Steps 6 through 8 for the east 32WSS-L card.

Step 11 If you are using a tunable laser, follow the manufacturer's instructions to complete the following steps. If you are using a TXP_MR_10E_L card, continue with Step 12.

a. Set the output power to a nominal value, such as -3 dBm.

b. Set the tuner to the wavelength you will test, then continue with Step 13.

Step 12 If you are using a TXP_MR_10E_L card, complete the "DLP-G358 Provision TXP_MR_10E_L Card for Acceptance Testing" task for the TXP containing the wavelength you will test.

Step 13 Connect the tunable laser transmitter or the TXP_MR_10E_L card DWDM TX port to the east OPT-BST-L or OSC-CSM LINE RX port. If an east OPT-AMP-L card is installed, insert a 10-dB attenuator on the fiber coming from the TXP_MR_10E_L card.

Caution

Failure to use proper attenuation might damage equipment.

Step 14 If an OPT-AMP-L card configured as an OPT-PRE is installed on the east side, complete the following steps. If not, continue with Step 15.

a. Display the east OPT-AMP-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power parameter for Port 1. Record the value.

d. Display the east OPT-BST-L or OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Locate the Power value for Port 2 (if an OPT-BST-L card) or Port 3 (if an OSC-CSM card). Verify that the value matches the power recorded in Step c, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-AMP-L card and the OPT-BST-L or OSC-CSM card. Check the values again. If they still do not match, contact your next level of support.

g. Complete the "DLP-G360 Verify the OPT-AMP-L (OPT-PRE Mode) Amplifier Laser and Power" task.

Step 15 If MMU cards are installed complete the following steps. If an MMU cards are not installed, continue with Step 16.

a. Display the east MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 3 (COM-RX) power parameter. Record the value.

d. If an east OPT-AMP-L card provisioned as an OPT-PRE is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the OPT-AMP-L Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an east OPT-BST-L card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

i. Verify that value in Step e, g, or h matches the power recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the MMU card and the OPT-BST-L, OPT-AMP-L, or OSC-CSM cards. Check the values again. If they still do not match, contact your next level of support.

j. Display the east MMU card in card view.

k. Click the Provisioning > Optical Line > Parameters tabs.

l. Record the value in the Power table cell for Port 2(EXP-TX) of the east MMU card.

m. Display the east 32WSS-L card in card view.

n. Click the Provisioning > Optical Line > Parameters tabs.

p. Continue with Step 17.

Step 16 Verify the east 32WSS-L to OPT-BST-L, OPT-AMP-L, or OSC-CSM card cable connection:

a. Display the east 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 Power parameter. Record the value.

d. If an east OPT-AMP-L card provisioned as an OPT-PRE is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2, then continue with Step i.

f. If an east OPT-BST-L card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Power value for Port 3, then continue with Step i.

h. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2, then continue with Step i.

i. Verify that the value in Step e, g, or h matches the power recorded in Step c, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L card and the OPT-AMP-L, OPT-BST-L, or OSC-CSM card. Check the values again. If they still do not match, contact your next level of support.

Step 17 Verify the EXPRESS cable connection between the two 32WSS-L cards:

a. Display the east 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 65 (EXP-TX) Power parameter. Record the value.

a. Display the west 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power value for Port 66 (EXP-RX). Verify that the value matches the power recorded in Step c, +/-1 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L cards. Check the values again. If they still do not match, contact your next level of support.

Step 18 Display the west 32WSS-L card in card view.

Step 20 Wait 60 to 70 seconds, then locate the Power and VOA Power Ref parameters for the tested PASS-THROUGH port. Verify that the Power value is equal to the VOA Power Ref value, +/- 1.5 dBm. If the Power value is not equal to the VOA Power Ref value, +/- 1.5 dBm, contact your next level of support.

Step 21 If an MMU card is installed on the west side, complete the following steps. If an MMU card is not installed on the west side, continue with Step 22.

a. Display the west 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67(COM-TX).

d. Display the west MMU card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

g. Record the value in the Power table cell for Port 4 (COM-TX).

h. If an OPT-BST-L card is installed on the west side, display it in card view and complete Step i. If not, continue with Step j.

i. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step k.

j. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step k.

k. Verify that the value in Step i or j matches the power recorded in Step g, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST-L, or OSC-CSM and MMU cards. Check the values again. If they still do not match, contact your next level of support.

l. Continue with Step 23.

Step 22 If an OPT-BST-L card is installed on the east side, complete the following steps. If not, continue with Step 23.

a. Display the east OPT-BST-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 1 Power parameter. Record the value.

d. Display the east 32WSS-L card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Locate the Power value for Port 67. Verify that the value matches the power recorded in Step c, +/-1 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST-L and 32WSS-L cards. Check the values again. If they still do not match, contact your next level of support.

g. Complete the "DLP-G79 Verify the OPT-BST, OPT-BST-E, or OPT-BST-L Amplifier Laser and Power" task.

Step 23 If a west OPT-AMP-L card provisioned as an OPT-PRE is installed, complete the following steps. If not, continue with Step 24.

a. Display the west OPT-AMP-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power parameter for Port 1 (COM-RX). Record the value.

d. Display the west OPT-BST-L or OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Locate the Power value for Port 2 (COM-TX) (OPT-BST-L) or Port 3 (COM-TX) (OSC-CSM). Verify that the value matches the power recorded in Step c, +/- 2.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-AMP-L card and the OPT-BST-L or OSC-CSM card. Check the values again. If they still do not match, contact your next level of support.

g. For the west OPT-AMP-L card provisioned as an OPT-PRE, complete the "DLP-G360 Verify the OPT-AMP-L (OPT-PRE Mode) Amplifier Laser and Power" task.

Step 24 If an MMU card is installed on the west side, complete the following steps, then continue with Step 26. If an MMU card is not installed on the west side, continue with Step 25.

a. Display the west MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 3 (COM-RX) power parameter. Record the value.

d. If an west OPT-AMP-L card provisioned in OPT-PRE mode is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the OPT-AMP-L Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an OPT-BST-L card is installed on the west side, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

i. Verify that value in the Step e, g, or h matches the power recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the MMU card and the OPT-BST-L, OPT-AMP-L, or OSC-CSM cards. Check the values again. If they still do not match, contact your next level of support.

j. Display the east MMU card in card view.

k. Click the Provisioning > Optical Line > Parameters tabs.

l. Record the value in the Power table cell for Port 2(EXP-TX) of the west MMU card.

m. Display the west 32WSS-L card in card view.

n. Click the Provisioning > Optical Line > Parameters tabs.

o. Verify that the value in the Power table cell for Port 68 (COM-RX) is equal to the value recorded in Step l, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS and cards and the MMU cards. Check the values again. If they still do not match, contact your next level of support.

p. Continue with Step 26.

Step 25 Verify the west 32WSS-L card to OPT-BST-L, OPT-AMP-L, or OSC-CSM card cable connection:

a. Display the west 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If a west OPT-AMP-L card is installed, display it in card view, and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If a west OPT-BST-L card is installed, display it in card view, and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the west OSC-CSM card in card view, click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

i. Verify that the value in Step e, g, or h matches the power recorded in Step c, +/-1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L card and the OPT-AMP-L, OPT-BST-L, or OSC-CSM card. Check the values again. If they still do not match, contact your next level of support.

Step 26 Verify the EXPRESS cable connection between the two 32WSS-L cards:

a. Display the west 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 65 (EXP-TX) Power parameter. Record the value.

a. Display the east 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power value for Port 66 (EXP-RX). Verify that the value matches the power recorded in Step c, +/- 1 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L cards. Check the values again. If they still do not match, contact your next level of support.

Step 27 Display the east 32WSS-L card in card view.

Step 29 Wait 60 to 70 seconds (or click Reset), then locate the Power and VOA Power Ref parameters for the tested PASS-THROUGH port. Verify that the Power value is equal to the VOA Power Ref value, +/-1.5 dBm. If the Power value is not equal to the VOA Power Ref value +/-1.5 dBm, consult your next level of support.

Step 30 If an MMU card is installed on the east side, complete the following steps. If an MMU card is not installed on the east side, continue with Step 31.

a. Display the east 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67(COM-TX).

d. Display the east MMU card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port 1(EXP-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L and MMU cards. Check the values again. If they still do not match, contact your next level of support.

g. Record the value in the Power table cell for Port 4 (COM-TX).

h. If a east OPT-BST-L card is installed, display it in card view and complete Step i. If not, continue with Step j.

i. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step k.

j. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step k.

k. Verify that the value in Step i or j matches the power recorded in Step g, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST-L, or OSC-CSM and MMU cards. Check the values again. If they still do not match, contact your next level of support.

l. Continue with Step 32.

Step 31 If an OPT-BST-L or OSC-CSM card is installed on the east side, complete the following steps. If not, continue with Step 32.

a. Display the east OPT-BST-L or OSC-CSM card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 1 (COM-RX) Power parameter (OPT-BST-L card) or the Port 2 (COM-RX) Power parameter (OSC-CSM card). Record the value.

d. Display the east 32WSS-L card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Locate the Power value for Port 67 (COM-TX). Verify that the value matches the power recorded in Step c, +/-1 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST-L and OSC-CSM or 32WSS-L cards. Check the values again. If they still do not match, contact your next level of support.

g. Complete the "DLP-G79 Verify the OPT-BST, OPT-BST-E, or OPT-BST-L Amplifier Laser and Power" task.

Step 32 Repeat Steps 18, 19, 27 and 28 for the remaining wavelengths to be tested. If you have tested all the wavelengths, continue with Step 33.

Step 33 Display the east 32WSS-L card in card view.

Step 34 Click the Maintenance tab.

Step 35 Under Operating Mode, click the table cell and choose Not Assigned from the drop-down list for all wavelengths.

Step 36 Click Apply, then click Yes to confirm.

Step 37 Display the west 32WSS-L in card view.

Step 38 Repeat Steps 34 through 36 for the west 32WSS-L card.

Step 39 Remove the TXP or tunable laser from the east OPT-BST-L or OSC-CSM line side TX and RX ports.

Step 40 Remove the loopback fiber from the line RX and TX in the west OPT-BST-L or OSC-CSM card.

Step 41 Return to your originating procedure (NTP).

DLP-G363 Verify the East ROADM L-Band Add/Drop Channels


Purpose	This procedure verifies the signal flow through the east side of a ROADM node for L-band add/drop channels.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_L An optical power meter or optical spectrum analyzer 2 bulk attenuators (10 dB) with LC connectors
Prerequisite Procedures	"DLP-G46 Log into CTC" task
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note Throughout this task, west refers to Slots 1 through 8, and east refers to Slots 10 through 17.

Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), display the Alarms tab.

Step 2 Create a physical loopback on the east OPT-BST-L or OSC-CSM card by connecting the LINE TX port to its LINE RX port. For OPT-BST-L cards, connect a 10-dB bulk attenuator to the fiber. (OSC-CSM cards do not require attenuation.)

Caution

Failure to use proper attenuation might damage equipment.

Step 3 Wait 2 to 3 minutes, then click the Alarms tab. Verify that the LOS alarms on the east OSCM or OSC-CSM card and the OPT-BST-L card have cleared. The clearing of the LOS alarms indicates that the OSC link is active on the east side.

Note An SDCC Termination Failure alarm will continue to appear due to the OSC signal loopback.

Step 4 If you are using a tunable laser, follow the manufacturer's instructions to complete the following steps. If you are using a TXP_MR_10E_L card, continue with Step 5.

a. Set the output power to a nominal value, such as -3 dBm.

b. Set the tuner to the wavelength you are testing, then continue with Step 7.

Step 5 If you are using a TXP_MR_10E_L card, complete the "DLP-G358 Provision TXP_MR_10E_L Card for Acceptance Testing" task for the TXP containing the wavelength you will test. Refer to "Table 4-232WSS-L Ports and Wavelengths Test Checklist" task, if needed.

Step 6 If you are using a TXP_MR_10E_L card, complete the following steps. If you are using a tunable laser, continue with Step 7.

a. Display the TXP_MR_10E_L in card view.

b. Click the Performance > Optics PM > Current Values tabs.

c. Locate the Port 2 (Trunk) table cell for the TX Optical Pwr parameter. Record the value.

Step 7 Connect the tunable laser transmitter or the TXP_MR_10E_L card DWDM TX port to the east side fiber patch panel MUX port that corresponds to the east 32WSS-L card port carrying the tested wavelength.

Step 8 Connect the TXP_MR_10E_L DWDM RX port or the power meter RX port to the east side fiber patch panel DMX port that is connected with the east 32DMX-L card CHAN-TX port carrying the tested wavelength. (If the TXP_MR_10E_L card was installed during Chapter 3 "Turn Up a Node," simply verify the cable connection.)

Step 9 Display the 32WSS-L card in card view.

Step 10 Click the Maintenance tab.

Step 11 For each wavelength that you will test, click the table cell under Operating Mode and choose Add Drop from the drop-down list.

Step 12 Click Apply and then Yes, to confirm.

Step 15 Click the Provisioning > Optical Line > Parameters tabs and record the value in the Power table cell for Port 67 (COM-TX) for the wavelength under test.

Step 16 Verify that the power value from Step 15 reaches the EastSide.Tx.Power.Add&Drop - Output Power set +/- 1 dBm. To view this setpoint:

a. In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Provisioning tabs.

b. In the Selector window on the left, expand the East Side parameters tree view.

c. Expand the TX category.

d. Expand the Power category, then highlight Add&Drop - Output Power.

e. View the EastSide.TxPower.Add&Drop - Output Power parameter on the right pane.

f. If the power value does not match the value recorded in Step 15, +/- 2dBm, contact your next level of support.

Step 17 If an MMU card is installed on the east side, complete the following steps. If an MMU card is not installed on the east side, continue with Step 18.

a. Display the east 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. Display the east MMU card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port 1(EXP-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L and MMU cards. Check the values again. If they still do not match, contact your next level of support.

g. Record the value in the Power table cell for Port 4 (COM-TX).

h. If a east OPT-BST-L card is installed, display it in card view and complete Step i. If not, continue with Step j.

i. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step k.

j. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step k.

k. Verify that the value in Step i or j matches the power recorded in Step g, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST-L or OSC-CSM and MMU cards. Check the values again. If they still do not match, contact your next level of support.

l. Continue with Step 19.

Step 18 Verify the connection between the 32WSS-L and OPT-BST-L or OSC_CSM cards:

a. Display the east 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. If a OPT-BST-L card is installed on the east side, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step g.

f. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step g.

g. Verify that the value in Step e or f matches the power recorded in Step c, +/- 1.0 dB. If so, continue with Step 19. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST-L or OSC-CSM and 32WSS-L cards. Check the values again. If they still do not match, contact your next level of support.

Step 19 If an OPT-AMP-L card provisioned in OPT-PRE mode is installed on the east side, complete the following steps. If not, continue with Step 20.

a. Display the east OPT-AMP-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power parameter for Port 1 (COM-RX). Record the value.

d. Display the east OPT-BST-L or OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Locate the Port 2 (COM-TX) Power value (for OPT-BST-L cards) or Port 3 (COM-TX) Power value (for OSC-CSM card). Verify that the value matches the power recorded in Step c, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-AMP-L card and the OPT-BST-L or OSC-CSM card. Check the values again. If they still do not match, contact your next level of support.

g. For the east OPT-AMP-L card, complete the "DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task.

Step 20 If an MMU card is installed on the east side, complete the following steps. If an MMU card is not installed on the east side, continue with Step 21.

a. Display the east MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If an OPT-AMP-L card provisioned in OPT-PRE mode is installed on the east side, display it in card view and complete Step e. If not, continue with Step f.

e. Click the OPT-PRE Provisioning > Opt.Ampli.Line > Parameters tabs. Record the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an east OPT-BST-L card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the east OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

i. Verify that value in the Step e, g, or h matches the power recorded in Step e, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the MMU card and the OPT-BST-L or OSC-CSM cards. Check the values again. If they still do not match, contact your next level of support.

j. Display the east MMU card in card view.

k. Click the Provisioning > Optical Line > Parameters tabs.

l. Record the value in the Power table cell for Port 2 (EXP-TX).

m. Display the east 32WSS-L card in card view.

n. Click the Provisioning > Optical Line > Parameters tabs.

o. Verify that the value in the Power table cell for Port 68 (COM-RX) is equal to the value recorded in Step l, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L and MMU cards. Check the values again. If they still do not match, contact your next level of support.

p. Continue with Step 22.

Step 21 Verify the connection between the east 32WSS-L card and the OPT-BST-L, OPT-AMP-L (in OPT-PRE mode), or OSC-CSM card:

a. Display the east 32WSS-L in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If an east OPT-AMP-L card provisioned in OPT-PRE mode is installed, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Opt.Ampli.Line > Parameters tabs and read the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an east OPT-BST-L card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the east OSC-CSM card in card view. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

i. Verify that the value in Step e, g, or h matches the power recorded in Step c, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L card and the OPT-AMP-L, OPT-BST-L, or OSC-CSM card.

Step 22 Verify the east 32WSS-L and 32DMX-L connection:

a. Display the east 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs, and record the value in the Power table cell for Port 69 (DROP-TX).

c. Display the east 32DMX-L card in card view.

d. Click the Provisioning > Optical Line > Parameters tabs. Record the value in the Port 2 (COM-RX) table cell. Verify that the value is equal to the value recorded in b., +/- 1 dBm. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L and 32DMX-L cards. Check the values again. If they still do not match, contact your next level of support.

Step 23 Display the east 32DMX-L card in card view.

Step 24 Click the Provisioning > Optical Chn > Parameters tab. Record the CHAN-TX port value under the Power parameter for the wavelength under test.

Step 25 Verify that the power value from Step 24 reaches the EastSide.Rx.Power.Add&Drop - Drop Power setpoint +/- 2 dBm. To view this setpoint:

a. Go to node view (single-shelf mode) or multishelf view (multishelf mode) and click the Provisioning > WDM-ANS > Provisioning tabs.

b. In the Selector window on the left, expand the East Side parameters tree view.

c. Expand the RX category.

d. Expand the Power category, then highlight Add&Drop - Drop Power.

e. View the EastSide.Rx.Power.Add&Drop - Drop Power parameter on the right pane.

f. If the power value does not match the value recorded in Step 24 (+/- 2 dBm), contact your next level of support.

Step 26 Display the TXP_MR_10E_L card in card view.

Step 27 Click the Performance > Optics PM > Current Values tabs.

a. Remove, clean, and replace the cable connecting the TXP_MR_10E_C RX port to the east fiber patch panel DMX port for the tested wavelength. See the "NTP-G115 Clean Fiber Connectors" procedure.

b. Repeat this step. If the power values still do not match (+/- 2 dBm) contact your next level of support.

Step 29 Repeat Steps 4 through 28 for the remaining wavelengths.

Step 30 Display the east 32WSS-L card in card view.

Step 31 Click the Maintenance tab.

Step 32 Click the table cell under Operating Mode and choose Not Assigned from the drop-down list for all wavelengths.

Step 33 Click Apply, then click Yes to confirm.

Step 34 Disconnect the TXP or tunable laser from the east side patch panel.

Step 35 Unplug the physical loopback fiber from the line TX and RX in the OPT-BST-L or OSC-CSM card.

Step 36 Return to your originating procedure (NTP).

DLP-G364 Verify the West ROADM L-Band Add/Drop Channels


Purpose	This procedure verifies the signal flow through the west side of a ROADM node for L-band add/drop channels.
Tools/Equipment	One of the following: •A tunable laser •TXP_MR_10E_L An optical power meter or optical spectrum analyzer 2 bulk attenuators (10 dB) with LC connectors
Prerequisite Procedures	"DLP-G46 Log into CTC" task
Required/As Needed	Required
Onsite/Remote	Onsite
Security Level	Superuser

Note Throughout this task, west refers to Slots 1 through 8, and east refers to Slots 10 through 17.

Step 1 In node view (single-shelf mode) or multishelf view (multishelf mode), display the Alarms tab.

Step 2 Create a physical loopback on the west OPT-BST-L or OSC-CSM card by connecting the LINE TX port to its LINE RX port. For OPT-BST-L cards, connect a 10-dB bulk attenuator to the fiber. (OSC-CSM cards do not require attenuation.)

Caution

Failure to use proper attenuation might damage equipment.

Step 3 Wait 2 to 3 minutes, then click the Alarms tab. Verify that the LOS alarms on the west OSCM or OSC-CSM card and the OPT-BST-L card have cleared. The clearing of the LOS alarms indicates that the OSC link is active on the west side.

Note An SDCC Termination Failure alarm will continue to appear due to the OSC signal loopback.

Step 4 If you are using a tunable laser, follow the manufacturer's instructions to complete the following steps. If you are using a TXP_MR_10E_L card, continue with Step 5.

a. Set the output power to a nominal value, such as -3 dBm.

b. Set the tuner to the wavelength you are testing, then continue with Step 7.

Step 6 If you are using a TXP_MR_10E_L card, complete the following steps. If you are using a tunable laser, continue with Step 7.

a. Display the TXP_MR_10E_L in card view.

b. Click the Performance > Optics PM > Current Values tabs.

c. Locate the Port 2 (Trunk) table cell for the TX Optical Pwr parameter. Record the value.

Step 7 Connect the tunable laser transmitter or the TXP_MR_10E_L card DWDM TX port to the west side fiber patch panel MUX port that corresponds to the west 32WSS-L card port carrying the tested wavelength.

Step 8 Connect the TXP_MR_10E_L DWDM RX port or the power meter RX port to the west side fiber patch panel DMX port that is connected with the west 32DMX-L card CHAN-TX port carrying the tested wavelength. (If the TXP_MR_10E_L card was installed during Chapter 3 "Turn Up a Node," simply verify the cable connection.)

Step 9 Display the 32WSS-L card in card view.

Step 10 Click the Maintenance tab.

Step 11 For each wavelength that you will test, click the table cell under Operating Mode and choose Add Drop from the drop-down list.

Step 12 Click Apply and then Yes, to confirm.

Step 15 Click the Provisioning > Optical Line > Parameters tabs and record the value in the Power table cell for Port 67 (COM-TX) for the wavelength under test.

Step 16 Verify that the power value from Step 15 reaches the WestSide.Tx.Power.Add&Drop - Output Power set +/- 1 dBm. To view this setpoint:

a. In node view (single-shelf mode) or multishelf view (multishelf mode), click the Provisioning > WDM-ANS > Provisioning tabs.

b. In the Selector window on the left, expand the West Side parameters tree view.

c. Expand the TX category.

d. Expand the Power category, then highlight Add&Drop - Output Power.

e. View the WestSide.TxPower.Add&Drop - Output Power parameter on the right pane.

f. If the power value does not match the value recorded in Step 15, +/- 2dBm, contact your next level of support.

Step 17 If an MMU card is installed on the west side, complete the following steps. If an MMU card is not installed on the west side, continue with Step 18.

a. Display the west 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. Display the west MMU card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

f. Verify that the value in the Power table cell for Port 1(EXP-RX) is equal to the value recorded in Step c, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L and MMU cards. Check the values again. If they still do not match, contact your next level of support.

g. Record the value in the Power table cell for Port 4 (COM-TX).

h. If a west OPT-BST-L card is installed, display it in card view and complete Step i. If not, continue with Step j.

i. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step k.

j. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step k.

k. Verify that the value in Step i or j matches the power recorded in Step g, +/- 1.5 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST-L or OSC-CSM and MMU cards. Check the values again. If they still do not match, contact your next level of support.

l. Continue with Step 19.

Step 18 Verify the connection between the 32WSS-L and OPT-BST-L or OSC_CSM cards:

a. Display the west 32WSS-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Record the value in the Power table cell for Port 67 (COM-TX).

d. If a OPT-BST-L card is installed on the west side, display it in card view and complete Step e. If not, continue with Step f.

e. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 1 (COM-RX), then continue with Step g.

f. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-RX), then continue with Step g.

g. Verify that the value in Step e or f matches the power recorded in Step c, +/- 1.0 dB. If so, continue with Step 19. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the OPT-BST-L or OSC-CSM and 32WSS-L cards. Check the values again. If they still do not match, contact your next level of support.

Step 19 If an OPT-AMP-L card provisioned in OPT-PRE mode is installed on the west side, complete the following steps. If not, continue with Step 20.

a. Display the west OPT-AMP-L card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Power parameter for Port 1 (COM-RX). Record the value.

d. Display the west OPT-BST-L or OSC-CSM card in card view.

e. Click the Provisioning > Optical Line > Parameters tabs.

g. For the west OPT-AMP-L card, complete the "DLP-G80 Verify the OPT-PRE Amplifier Laser and Power" task.

Step 20 If an MMU card is installed on the west side, complete the following steps. If an MMU card is not installed on the west side, continue with Step 21.

a. Display the west MMU card in card view.

b. Click the Provisioning > Optical Line > Parameters tabs.

c. Locate the Port 68 (COM-RX) Power parameter. Record the value.

d. If an OPT-AMP-L card provisioned in OPT-PRE mode is installed on the west side, display it in card view and complete Step e. If not, continue with Step f.

e. Click the OPT-PRE Provisioning > Opt.Ampli.Line > Parameters tabs. Record the Total Output Power value for Port 2 (COM-TX), then continue with Step i.

f. If an west OPT-BST-L card is installed, display it in card view and complete Step g. If not, continue with Step h.

g. Click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 2 (COM-TX), then continue with Step i.

h. Display the west OSC-CSM card in card view, click the Provisioning > Optical Line > Parameters tabs and read the Power value for Port 3 (COM-TX), then continue with Step i.

i. Verify that value in the Step e, g, or h matches the power recorded in Step e, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the MMU card and the OPT-BST-L or OSC-CSM cards. Check the values again. If they still do not match, contact your next level of support.

j. Display the west MMU card in card view.

k. Click the Provisioning > Optical Line > Parameters tabs.

l. Record the value in the Power table cell for Port 2 (EXP-TX).

m. Display the west 32WSS-L card in card view.

n. Click the Provisioning > Optical Line > Parameters tabs.

o. Verify that the value in the Power table cell for Port 68 (COM-RX) is equal to the value recorded in Step l, +/- 1.0 dB. If not, use the "NTP-G115 Clean Fiber Connectors" procedure to clean the fiber connection between the 32WSS-L and MMU cards. Check the values again. If they still do not match, contact your next level of support.

p. Continue with Step 22.

Step 21 Verify the connection between the west 32WSS-L card and the OPT-BST-L, OPT-AMP-L (in OPT-PRE mode), or OSC-CSM card:

a. Display the west 32WSS-L in card view.