Configuring Channelized SONET/SDH

This module describes the configuration of Channelized SONET/SDH.

Feature History for Configuring Channelized SONET/SDH

Release

Modification

Release 3.9.0

Support for the following SPA was introduced on the Cisco ASR 9000 Series Router:

  • Cisco 2-Port Channelized OC-12/DS0 SPA

Release 4.0.0

Support for the following SPA was introduced on the Cisco ASR 9000 Series Router:

  • Cisco 1-Port Channelized OC-48/STM-16 SPA

Support for SDH, E3, E1, and POS channelization was added for the Cisco 2-Port Channelized OC-12/DS0 and Cisco 1-Port Channelized OC-48/STM-16 SPAs.

Release 4.0.1

Support for the following SPA was introduced on the Cisco ASR 9000 Series Router:

  • Cisco 1-Port Channelized OC-3/STM-1 SPA

Configuring Channelized SONET/SDH

This module describes the configuration of Channelized SONET/SDH.

Feature History for Configuring Channelized SONET/SDH

Release

Modification

Release 3.9.0

Support for the following SPA was introduced on the Cisco ASR 9000 Series Router:

  • Cisco 2-Port Channelized OC-12/DS0 SPA

Release 4.0.0

Support for the following SPA was introduced on the Cisco ASR 9000 Series Router:

  • Cisco 1-Port Channelized OC-48/STM-16 SPA

Support for SDH, E3, E1, and POS channelization was added for the Cisco 2-Port Channelized OC-12/DS0 and Cisco 1-Port Channelized OC-48/STM-16 SPAs.

Release 4.0.1

Support for the following SPA was introduced on the Cisco ASR 9000 Series Router:

  • Cisco 1-Port Channelized OC-3/STM-1 SPA

Prerequisites for Configuring Channelized SONET/SDH

You must be in a user group associated with a task group that includes the proper task IDs. The command reference guides include the task IDs required for each command. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Before configuring Channelized SONET/SDH, be sure that the following tasks and conditions are met:

  • You have at least one of the following SPAs installed in your chassis:

    • Cisco 1-Port Channelized OC-3/STM-1 SPA

    • Cisco 2-Port Channelized OC-12c/DS0 SPA

    • Cisco 1-Port Channelized OC-48/STM-16 SPA

  • You should know how to apply and specify the SONET controller name and interface-path-id with the generalized notation rack/slot/module/port. The SONET controller name and interface-path-id are required with the controller sonet command.

Information About Configuring Channelized SONET/SDH

To configure Channelized SONET/SDH, you must understand these concepts:

Channelized SONET Overview

Synchronous Optical Network (SONET) is an American National Standards Institute (ANSI) specification format used in transporting digital telecommunications services over optical fiber.

Synchronous Digital Hierarchy (SDH) is the international equivalent of SONET.

Channelized SONET provides the ability to transport SONET frames across multiplexed T3/E3 and virtual tributary group (VTG) channels.

Channelized SONET is supported on the following SPAs:

  • Cisco 1-Port Channelized OC-48/STM-16 SPA

  • Cisco 1-Port Channelized OC-3/STM-1 SPA

  • Cisco 2-Port Channelized OC-12c/DS0 SPA

Channelized SDH is supported on the following SPAs:

  • Cisco 1-Port Channelized OC-48/STM-16 SPA

  • Cisco 1-Port Channelized OC-3/STM-1 SPA

  • Cisco 2-Port Channelized OC-12c/DS0 SPA

SONET uses Synchronous Transport Signal (STS) framing. An STS is the electrical equivalent to an optical carrier 1 (OC-1).

SDH uses Synchronous Transport Mode (STM) framing. An STM-1 is the electrical equivalent to 3 optical carrier 1s (OC-1s).

A channelized SONET interface is a composite of STS streams, which are maintained as independent frames with unique payload pointers. The frames are multiplexed before transmission.

When a line is channelized, it is logically divided into smaller bandwidth channels called paths. These paths carry the SONET payload. The sum of the bandwidth on all paths cannot exceed the line bandwidth.

When a line is not channelized, it is called clear channel, and the full bandwidth of the line is dedicated to a single channel that carries broadband services.

An STS stream can be channelized into the following types of channels:

  • T3/E3

  • VT1.5 mapped T1

  • Packet over SONET/SDH (POS) (OC12 and OC48 only)

The T3/E3 channels can be channelized further into T1s, and the T1s can be channelized into time slots (DS0s), except on the 1-Port Channelized OC-48/STM-16 SPA, which does not support T1 or DS0s.

Channelizing a SONET line consists of two primary processes:

  • Configuring the controller

  • Configuring the interface into channelized paths

You configure the controller first by setting the mode of the STS path. The mode can be set to T3, or VT1.5-mapped T1, or POS, depending on your hardware support.


Note

POS is supported only on the STS-3c and STS-12c paths on the Cisco 1-Port Channelized OC-12/DS0 SPA and on the STS-3c, STS-12c, and STS-48c paths on the Cisco 1-Port Channelized OC-48/STM-16 SPA.

When the mode is specified, the respective controller is created, and the remainder of the configuration is applied on that controller. For example, mode T3 creates a T3 controller. The T3 controller can then be configured to a serial channel, or it can be further channelized to carry T1s, and those T1s can be configured to serial interfaces.

Depending on the support for your installed SPA, each STS path can be independently configured into T3s, E3s, or VTGs, and so on.

This figure shows an example of three STS paths for a SONET controller. However, the 2-Port Channelized OC-12/DS0 SPA supports up to 12 STS paths, and the 1-Port Channelized OC-48/STM-16 SPA supports up to 48 STS paths, but the 1-Port Channelized OC-48/STM-16 SPA does not support VTGs.

Figure 1. SONET Controller STS Paths

This figure shows an example of some SONET controller configuration combinations.


Note

The 1-Port Channelized OC-48/STM-16 SPA on the Cisco ASR 9000 Series Router does not support VTGs.

Figure 1. SONET Controller Configuration Combinations

This figure shows the T3 paths that can be configured.


Note

Channelized T3 paths are only supported on the 1-Port Channelized OC-3/STM-1 SPA and 2-Port Channelized OC-12c/DS0 SPA.

Figure 2. SONET T3 Channelized Paths

This figure shows the VTG paths that can be configured.


Note

VTG paths are only supported on the Cisco 1-Port Channelized OC-3/STM-1 SPA and Cisco 2-Port Channelized OC-12c/DS0 SPA on the Cisco ASR 9000 Series Router.

Figure 3. SONET VTG Channelized Paths

Channelized SDH Overview

Synchronous Digital Hierarchy (SDH) is the international equivalent of SONET.

Channelized SDH is supported on the following SPAs:

  • Cisco 1-Port Channelized OC-48/STM-16 SPA

  • Cisco 1-Port Channelized OC-3/STM-1 SPA

  • Cisco 2-Port Channelized OC-12/DS0 SPA

A Synchronous Transport Module (STM) signal is the Synchronous Digital Hierarchy (SDH) equivalent of the SONET STS, but the numbers are different for each bandwidth. In this guide, the STM term refers to both path widths and optical line rates. The paths within an STM signals are called administrative units (AUs).

A summary of the basic terminology differences between SONET and SDH is as follows:

  • SONET STS is equivalent to SDH administrative unit (AU)

  • SONET VT is equivalent to SDH tributary unit (TU)

  • SDH basic building blocks are STM-1 (equivalent to STS-3) and STM-0 (equivalent to STS-1)

An administrative unit (AU) is the information structure that provides adaptation between the higher-order path layer and the multiplex section layer. It consists of an information payload (the higher-order virtual container) and an administrative unit pointer, which indicates the offset of the payload frame start relative to the multiplex section frame start.

An AU can be channelized into tributary units (TUs) and tributary unit groups (TUGs).

An administrative unit 4 (AU-4) consists of three STM-1s or an STM-3.

An administrative unit 3 (AU-3) consists of one STM-1.

An administrative unit group (AUG) consists of one or more administrative units occupying fixed, defined positions in an STM payload.

Table 1. SONET and SDH Terminology Equivalencies

SONET Term

SDH Term

SONET

SDH

STS-3c

AU-4

STS-1

AU-3

VT

TU

SPE

VC

Section

Regenerator Section

Line

Multiplex Section

Path

Path

On the Cisco ASR 9000 Series Router, the following levels of SDH channelization are supported:

  • 1-Port Channelized OC-3/STM-1 SPA

    • AU4 to TUG-3 to TUG-2 to VC-12 to E1 to NxDS0

    • AU4 to TUG-3 to VC-3 to DS3 (Clear Channel)

    • AU4 to TUG-3 to VC-3 to E3 (Clear Channel)

    • AU3 to TUG-2 to VC-11 to DS1 to NxDS0

  • 2-Port Channelized OC-12/DS0 SPA

    • AU-4-4c (VC-4-4c)

    • AU-4 (VC-4)

    • AU-4 to TUG-3 to VC-3 to DS3

    • AU-4 to TUG-3 to VC-3 to E3

    • AU-4 to TUG-3 to TUG-2 to VC-11 to T1 to NxDS0

    • AU-4 to TUG-3 to TUG-2 to VC-12 to E1to NxDS0

    • AU-3 to VC-3 to DS3

    • AU-3 to TUG-2 to VC-11 to T1 to NxDS0

    • AU-3 to TUG-2 to VC-12 to E1to NxDS0

    • AU-3 to VC-3 to E3

    • AU-3 to VC-3 to DS3 to T1 to NxDS0

    • AU-3 to VC-3 to DS3 to E1 to NxDS0

  • 1-Port Channelized OC-48/STM-16 SPA

    • DS3

    • E3

    • AU-3 (VC-3)

    • AU-4 (VC-4)

    • AU-4-4c (VC-4-4c)

    • AU-4-16c (VC-4-16c)

This figure shows an example of SDH AU-3 paths that can be configured on certain supported SPAs.


Note

The 1-Port Channelized OC-48/STM-16 SPA does not support further channelization of AU-3 paths into T1s.

Figure 5. SDH AU3 Paths

This figure shows the SDH AU4 paths that can be configured on supported SPAs.


Note

The 1-Port Channelized OC-48/STM-16 SPA only supports channelization to the T3 or E3 level. Further channelization of AU-4 paths is not supported.

Figure 6. SDH AU4 Paths

Default Configuration Values for Channelized SONET/SDH

This table describes the default configuration parameters that are present on the Channelized SONET/SDH.

Table 2. SONET/SDH Controller Default Cit onfiguration Values

Parameter

Default Value

Configuration File Entry

Clock source

line

clock source {internal | line}

SONET framing

sonet

framing {sdh | sonet}

How to Configure Channelized SONET/SDH

This section contains the following procedures:

Configuring SONET T3 and VT1.5-Mapped T1 Channels

This task explains how to configure a SONET line into T3 and VT-mapped T1 Channels.

Before you begin

  • You should know how to configure the SONET controller as specified in the “How to Configure Clear Channel SONET Controllers” section of the Configuring Clear Channel SONET Controllers module.

  • STS paths can be channelized into T3s on the following SPAs:

    • Cisco 1-Port Channelized OC-48/STM-16 SPA

    • Cisco 1-Port Channelized OC-3/STM-1 SPA

    • Cisco 2-Port Channelized OC-12/DS0 SPA

  • STS paths can be channelized into VTG mapped T1s on the following SPA:

    • Cisco 1-Port Channelized OC-3/STM-1 SPA

    • Cisco 2-Port Channelized OC-12/DS0 SPA

  • T3 paths can be channelized into T1s or E1s on the following SPA:

    • Cisco 1-Port Channelized OC-3/STM-1 SPA

    • Cisco 2-Port Channelized OC-12/DS0 SPA

  • T1 paths can be channelized into NxDS0s on the Cisco 2-Port Channelized OC-12/DS0 SPA.

Restrictions

T1s and E1s are not supported on the Cisco 1-Port Channelized OC-48/STM-16 SPA.

SUMMARY STEPS

  1. configure
  2. controller sonet interface-path-id
  3. clock source {internal | line}
  4. framing sonet
  5. sts number
  6. mode mode
  7. width number
  8. root
  9. controller controllerName instance
  10. mode mode
  11. root
  12. controller t1 interface-path-id
  13. channel-group number
  14. timeslots num1:num2:num3:num4
  15. or
  16. timeslots range1-range2
  17. show configuration
  18. root
  19. interface serial interface-path-id
  20. encapsulation {frame-relay | hdlc | ppp}
  21. ipv4 ip-address mask
  22. no shutdown
  23. end or commit
  24. show controllers sonet interface-path-id

DETAILED STEPS

  Command or Action Purpose
Step 1

configure

Example:


RP/0/RSP0/CPU0:router# configure

Enters global configuration mode.

Step 2

controller sonet interface-path-id

Example:


RP/0/RSP0/CPU0:router(config)# controller sonet 0/1/1/0

Enters SONET controller configuration submode and specifies the SONET controller name and interface-path-id with the rack/slot/module/port notation.

Step 3

clock source {internal | line}

Example:


RP/0/RSP0/CPU0:router(config-sonet)# clock source internal

Configures the SONET port transmit clock source, where the internal keyword sets the internal clock and the line keyword sets the clock recovered from the line.

  • Use the line keyword whenever clocking is derived from the network. Use the internal keyword when two routers are connected back to back or over fiber for which no clocking is available.

  • line is the default keyword.

    Note 

    • Internal clocking is required for SRP interfaces.

Step 4

framing sonet

Example:


RP/0/RSP0/CPU0:router(config-sonet)# framing sonet

Configures the controller for SONET framing.

SONET framing (sonet ) is the default.

Step 5

sts number

Example:


RP/0/RSP0/CPU0:router(config-sonet)# sts 1

Configures the STS stream specified by number . The ranges are:

  • 1 to 48—1 Port Channelized OC-48/STM-16 SPA

  • 1 to 3—1-Port Channelized OC-3/STM-1 SPA

  • 1 to 12—2-Port Channelized OC-12/DS0 SPA

Step 6

mode mode

Example:


RP/0/RSP0/CPU0:router(config-stsPath)# mode t3

Sets the mode of interface at the STS level. The possible modes are:

  • t3—SONET path carrying T3

  • vt15-t1—SONET path carrying virtual tributary 1.5 T1s (VT15 T1) (1-Port Channelized OC-3/STM-1 SPA and 2-Port Channelized OC-12c/DS0 SPA only)

  • pos—Packet over SONET

Step 7

width number

Example:


RP/0/RSP0/CPU0:router(config-stsPath)# width 3

Configures the number of the STS streams that are concatenated. 
The possible values for number are:

  • 1—Indicating one STS stream

  • 3—Indicating three STS streams (STS-3c)

  • 12—Indicating concatenation of 12 STS streams (STS-12c)

  • 48—Indicating concatenation of 48 STS streams (STS-48c). This is the default on the 1-Port Channelized OC-48/STM-16 SPA.

Widths 3, and 12, and 48 are configured on STS paths at natural boundaries, which coincide with the following path numbers:

  • 1, 4, 7, 10, and so on, for STS-3c

  • 1, 13, 25, and 37 for STS-12c

  • 1 for STS-48c

Step 8

root

Example:


RP/0/RSP0/CPU0:router(config-stsPath)# root

Exits to global configuration mode.

Step 9

controller controllerName instance

Example:


RP/0/RSP0/CPU0:router(config)# controller t3 0/1/1/0/0

Enters controller configuration submode and specifies the controller name and instance identifier with the rack/slot/module/port/controllerName notation. The controller names are:

  • t3—SONET path carrying T3

  • vt15-t1—SONET path carrying virtual tributary 1.5 T1s (VT15 T1) (1-Port Channelized OC-3/STM-1 SPA and 2-Port Channelized OC-12c/DS0 SPA only)

Step 10

mode mode

Example:


RP/0/RSP0/CPU0:router(config-t3)# mode t1

Sets the mode of interface at this level. The possible modes are:

  • t1—Channelized into 28 T1s (1-Port Channelized OC-3/STM-1 SPA and 2-Port Channelized OC-12c/DS0 SPA only)

  • e1—Channelized into 21 E1s (1-Port Channelized OC-3/STM-1 SPA and 2-Port Channelized OC-12c/DS0 SPA only)

  • serial—Clear channel carrying an HDLC-like payload

Step 11

root

Example:


RP/0/RSP0/CPU0:router(config-t3)# root

Exits to global configuration mode.

Step 12

controller t1 interface-path-id

Example:


RP/0/RSP0/CPU0:router(config)# controller t1 0/1/1/0/0/0

Enters T1 controller configuration submode and specifies the T1 controller name and interface-path-id with the rack/slot/module/port/T3Num/T1num notation.

(1-Port Channelized OC-3/STM-1 SPA and 2-Port Channelized OC-12c/DS0 SPA only)

Step 13

channel-group number

Example:


RP/0/RSP0/CPU0:router(config-t1)# channel-group 1

Sets the channel group number to which time slots are assigned. The range is from 1 to 24.

Step 14

timeslots num1:num2:num3:num4

Step 15

or

Step 16

timeslots range1-range2

Example:


RP/0/0/CPU0:router(config-t1-channel_group)# timeslots 1:3:7:9
RP/0/0/CPU0:router(config-t1-channel_group)# timeslots 1-24

Specifies the time slots for the interface by number with the num1:num2:num3:num4 notation, or by range with the range1-range2 notation.

Step 17

show configuration

Example:


RP/0/RSP0/CPU0:router(config-t1-channel_group)# show configuration

Displays the contents of uncommitted configuration.

Step 18

root

Example:


RP/0/RSP0/CPU0:router(config-t3)# root

Exits to global configuration mode.

Step 19

interface serial interface-path-id

Example:


RP/0/RSP0/CPU0:router(config)# interface serial 0/1/1/0/0/0:0

Specifies the complete interface number with the rack/slot/module/port/T3Num/T1num:instance notation.

Step 20

encapsulation {frame-relay | hdlc | ppp}

Example:


RP/0/RSP0/CPU0:router(config-if)# encapsulation ppp

Specifies the encapsulation type with the one of the following keywords:

  • frame-relay —Frame Relay network protocol

  • hdlc —High-level Data Link Control (HDLC) synchronous protocol

  • ppp —Point-to-Point Protocol

Step 21

ipv4 ip-address mask

Example:


RP/0/RSP0/CPU0:router(config-if)# ip address 10.10.10.10 255.255.255.255

Assigns an IP address and subnet mask to the interface.

Step 22

no shutdown

Example:


RP/0/RSP0/CPU0:router(config-if)# no shutdown

Removes the shutdown configuration.

Note 

  • Removal of the shutdown configuration eliminates the forced administrative down on the interface, enabling it to move to an up or down state (assuming that the parent SONET layer is not configured administratively down).

Step 23

end or commit

Example:


RP/0/0RSP0/CPU0:router(config-sonet)# end

or 


RP/0/RSP0/CPU0:router(config-sonet)# commit

Saves configuration changes.

  • When you issue the end command, the system prompts you to commit changes: 

    
Uncommitted changes found, commit them before exiting(yes/no/cancel)?
[cancel]:

  • Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

  • Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

  • Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

  • Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Step 24

show controllers sonet interface-path-id

Example:


RP/0/RSP0/CPU0:router# show controllers sonet 0/1/1/0

Verifies the SONET controller configuration.

Configuring Packet over SONET Channels

This task explains how to configure Packet over SONET (POS) channels on SPAs supporting channelized SONET.

Before you begin

You have one of the following SPAs installed:

  • Cisco 1-Port Channelized OC-48/STM-16 SPA

  • Cisco 2-Port Channelized OC-12/DS0 SPA

SUMMARY STEPS

  1. configure
  2. controller sonet interface-path-id
  3. clock source {internal | line}
  4. framing {sdh | sonet}
  5. sts number
  6. width number
  7. mode mode scramble
  8. root
  9. interface pos interface-path-id
  10. encapsulation [hdlc | ppp | frame-relay [IETF]]
  11. pos crc {16 | 32}
  12. mtu value
  13. no shutdown
  14. end or commit
  15. show interfaces pos interface-path-id

DETAILED STEPS

  Command or Action Purpose
Step 1

configure

Example:


RP/0/RSP0/CPU0:router# configure

Enters global configuration mode.

Step 2

controller sonet interface-path-id

Example:


RP/0/RSP0/CPU0:router(config)# controller sonet 0/1/1/0

Enters SONET controller configuration submode and specifies the SONET controller name and interface-path-id with the rack/slot/module/port notation.

Step 3

clock source {internal | line}

Example:


RP/0/RSP0/CPU0:router(config-sonet)# clock source internal

Configures the SONET port transmit clock source, where the internal keyword sets the internal clock and the line keyword sets the clock recovered from the line.

  • Use the line keyword whenever clocking is derived from the network. Use the internal keyword when two routers are connected back to back or over fiber for which no clocking is available.

  • line is the default keyword.

    Note 

    • Internal clocking is required for SRP interfaces.

Step 4

framing {sdh | sonet}

Example:


RP/0/RSP0/CPU0:router(config-sonet)# framing sonet

(Optional) Configures the controller framing with either the sdh keyword for Synchronous Digital Hierarchy (SDH) framing or the sonet keyword for SONET framing.

SONET framing (sonet ) is the default.

Step 5

sts number

Example:


RP/0/RSP0/CPU0:router(config-sonet)# sts 1

Configures the STS stream specified by number . The ranges are:

  • 1 to 12 on the 2-Port Channelized OC12c/DS0 SPA

  • 1 to 48 on the 1 Port Channelized OC48/DS3 SPA

Step 6

width number

Example:


RP/0/RSP0/CPU0:router(config-stsPath)# width 3

Configures the number of the STS streams that are concatenated. 
The possible values for number are:

  • 3—Indicating three STS streams (STS-3c)

  • 12—Indicating concatenation of 12 STS streams (STS-12c)

  • 48—Indicating concatenation of 48 STS streams (STS-48c)

Widths 3, 12, and 48 are configured on STS paths at natural boundaries, which coincide with the following path numbers:

  • 1, 4, 7, 10, and so on, for STS-3c

  • 1, 13, 25, and 37 for STS-12c

  • 1 for STS-48c

    Note 

    • POS interfaces are not supported when width is 1.

Step 7

mode mode scramble

Example:


RP/0/RSP0/CPU0:router(config-stsPath)# mode pos scramble

Sets the mode of interface at the STS level. Set the mode to pos to create POS interface (OC12 and OC48 only).

Step 8

root

Example:


RP/0/RSP0/CPU0:router(config-stsPath)# root

Exits to global configuration mode.

Step 9

interface pos interface-path-id

Example:


RP/0/RSP0/CPU0:router(config)# interface POS 0/1/1/0

Specifies the POS interface name and notation rack/slot/module/port, and enters interface configuration mode.

Step 10

encapsulation [hdlc | ppp | frame-relay [IETF]]

Example:


RP/0/RSP0/CPU0:router(config-if)# encapsulation hdlc

(Optional) Configures the interface encapsulation parameters and details such as HDLC or PPP. The default is HDLC.

Step 11

pos crc {16 | 32}

Example:


RP/0/RSP0/CPU0:router(config-if)# pos crc 32

(Optional) Configures the CRC value for the interface. Enter the 16 keyword to specify 16-bit CRC mode, or enter the 32 keyword to specify 32-bit CRC mode.

The default CRC is 32.

Step 12

mtu value

Example:


RP/0/RSP0/CPU0:router(config-if)# mtu 4474

(Optional) Configures the POS MTU value.

The range is 64–65535.

Step 13

no shutdown

Example:


RP/0/RSP0/CPU0:router (config-if)# no shutdown

Removes the shutdown configuration.

Note 

  • Removal of the shutdown configuration eliminates the forced administrative down on the interface, enabling it to move to an up or down state (assuming that the parent SONET layer is not configured administratively down).

Step 14

end or commit

Example:


RP/0/RSP0/CPU0:router(config-sonet)# end

or 


RP/0/RSP0/CPU0:router(config-sonet)# commit

Saves configuration changes.

  • When you issue the end command, the system prompts you to commit changes: 

    
Uncommitted changes found, commit them before exiting(yes/no/cancel)?
[cancel]:

  • Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

  • Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

  • Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

  • Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Step 15

show interfaces pos interface-path-id

Example:


RP/0/0/CPU0:router# show interfaces pos 0/1/1/0

(Optional) Displays the interface configuration.

Configuring a Clear Channel SONET Controller for T3

This task explains how to configure a SONET line into a single T3 serial channel called clear channel. Clear channel is established by setting the T3 controller mode to serial.

Before you begin

SUMMARY STEPS

  1. configure
  2. controller sonet interface-path-id
  3. clock source {internal | line}
  4. framing sonet
  5. sts number
  6. mode t3
  7. root
  8. controller t3 interface-path-id
  9. mode serial
  10. root
  11. interface serial interface-path-id
  12. encapsulation {frame-relay | hdlc | ppp}
  13. ipv4 ip-address mask
  14. no shutdown
  15. end or commit
  16. show controllers sonet interface-path-id

DETAILED STEPS

  Command or Action Purpose
Step 1

configure

Example:


RP/0/RSP0/CPU0:router# configure

Enters global configuration mode.

Step 2

controller sonet interface-path-id

Example:


RP/0/RSP0/CPU0:router(config)# controller sonet 0/1/1/0

Enters SONET controller configuration submode and specifies the SONET controller name and interface-path-id with the rack/slot/module/port notation.

Step 3

clock source {internal | line}

Example:


RP/0/RSP0/CPU0:router(config-sonet)# clock source internal

Configures the SONET port transmit clock source, where the internal keyword sets the internal clock and the line keyword sets the clock recovered from the line.

  • Use the line keyword whenever clocking is derived from the network. Use the internal keyword when two routers are connected back to back or over fiber for which no clocking is available.

  • line is the default keyword.

    Note 

    • Internal clocking is required for SRP interfaces.

Step 4

framing sonet

Example:


RP/0/RSP0/CPU0:router(config-sonet)# framing sonet

Configures the controller for SONET framing. SONET framing (sonet ) is the default.

Step 5

sts number

Example:


RP/0/RSP0/CPU0:router(config-sonet)# sts 1

Configures the STS stream specified by number . The ranges are:

  • 1 to 48—1-Port Channelized OC-48/DS3 SPA

  • 1 to 3—1-Port Channelized OC-3/STM-1 SPA

  • 1 to 12—2-Port Channelized OC-12/DS0 SPA

Step 6

mode t3

Example:


RP/0/RSP0/CPU0:router(config-stsPath)# mode t3

Sets the mode of the interface at the STS level for T3.

Step 7

root

Example:


RP/0/RSP0/CPU0:router(config-stsPath)# root

Exits to global configuration mode.

Step 8

controller t3 interface-path-id

Example:


RP/0/RSP0/CPU0:router(config)# controller t3 0/1/1/0/0

Enters T3 controller configuration submode and specifies the T3 controller name and interface-path-id identifier with the rack/slot/module/port/T3Num notation.

Step 9

mode serial

Example:


RP/0/RSP0/CPU0:router(config-t3)# mode serial

Sets the mode of the interface to serial to establish a clear channel.

Step 10

root

Example:


RP/0/RSP0/CPU0:router(config-t3)# root

Exits to global configuration mode.

Step 11

interface serial interface-path-id

Example:


RP/0/RSP0/CPU0:router(config)# interface serial 0/1/1/0/0/0:0

Specifies the complete interface number with the rack/slot/module/port/T3Num/T1num:instance notation.

Step 12

encapsulation {frame-relay | hdlc | ppp}

Example:


RP/0/RSP0/CPU0:router(config-if)# encapsulation ppp

Specifies the encapsulation type with the one of the following keywords:

  • frame-relay —Frame Relay network protocol

  • hdlc —High-level Data Link Control (HDLC) synchronous protocol

  • ppp —Point-to-Point Protocol

Step 13

ipv4 ip-address mask

Example:


RP/0/RSP0/CPU0:router(config-if)# ip address 10.10.10.10 255.255.255.255

Assigns an IP address and subnet mask to the interface.

Step 14

no shutdown

Example:


RP/0/RSP0/CPU0:router(config-if)# no shutdown

Removes the shutdown configuration.

Note 

  • Removal of the shutdown configuration eliminates the forced administrative down on the interface, enabling it to move to an up or down state (assuming that the parent SONET layer is not configured administratively down).

Step 15

end or commit

Example:


RP/0/RSP0/CPU0:router(config-sonet)# end

or 


RP/0/RSP0/CPU0:router(config-sonet)# commit

Saves configuration changes.

  • When you issue the end command, the system prompts you to commit changes: 

    
Uncommitted changes found, commit them before exiting(yes/no/cancel)?
[cancel]:

  • Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

  • Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

  • Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

  • Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Step 16

show controllers sonet interface-path-id

Example:


RP/0//RSP0/CPU0:router# show controllers sonet 0/1/1/0

Verifies the SONET controller configuration.

Configuring Channelized SONET APS

This task explains how to configure APS for channelized SONET lines.

Before you begin

Restrictions

  • SONET APS is not supported on the 1-Port Channelized OC-48/STM-16 SPA.

  • The Cisco ASR 9000 Series Router supports multirouter APS only on the following SPAS:

    • 1-Port Channelized OC-3/STM-1 SPA

    • 2-Port Channelized OC-12c/DS0 SPA

SUMMARY STEPS

  1. aps group number
  2. channel 0 local sonet interface
  3. or
  4. channel 0 remote ip-address
  5. channel 1 local sonet interface
  6. or
  7. channel 1 remote ip-address
  8. signalling {sonet | sdh}
  9. end or commit
  10. show aps
  11. show aps group [number]

DETAILED STEPS

  Command or Action Purpose
Step 1

aps group number

Example:


RP/0/RSP0/CPU0:router(config)# aps group 1

Adds an APS group with a specified number and enters APS group configuration mode.

  • Use the aps group command in global configuration mode.

  • To remove a group, use the no form of this command, as in: no aps group number , where the value range is from 1 to 255.

    Note 

    • To use the aps group command, you must be a member of a user group associated with the proper task IDs for APS commands.

    • The aps group command is used even when a single protect group is configured.

Step 2

channel 0 local sonet interface

Step 3

or

Step 4

channel 0 remote ip-address

Example:


RP/0/RSP0/CPU0:router(config-aps)# channel 0 local SONET 0/0/0/1
or
RP/0/RSP0/CPU0:router(config-aps)# channel 0 remote 172.18.69.123

Creates a protect channel for the APS group, where 0 designates a protect channel.

Note 

  • The protect channel must be assigned before the active channel can be assigned.

  • To configure APS where both channels are on one router, use the channel local command for both the protect and active channels.
To configure APS using two different routers where the active channel is on one router and the protect channel is on another router, use the channel local command for either the protect or the active channel, but use the channel remote command for the other channel.

Step 5

channel 1 local sonet interface

Step 6

or

Step 7

channel 1 remote ip-address

Example:


RP/0/RSP0/CPU0:router(config-aps)# channel 1 local SONET 0/0/0/2
or
RP/0/0/CPU0:router(config-aps)# channel 1 remote 172.18.69.123

Creates an active channel for the APS group, where 1 designates an active channel.

Note 

  • The active channel must be assigned after the protect channel is assigned.

  • To configure APS where both channels are on one router, use the channel local command for both the protect and active channels.
To configure APS using two different routers where the active channel is on one router and the protect channel is on another router, use the channel local command for either the protect or the active channel, but use the channel remote command for the other channel.

Step 8

signalling {sonet | sdh}

Example:


RP/0/RSP0/CPU0:router(config-aps)# signalling sonet

Configures the K1K2 overhead byte used for automatic protection switching (APS). The keyword options are:

  • sonet —Sets signaling to SONET.

  • sdh —Sets signaling to Synchronous Digital Hierarchy (SDH).

Step 9

end or commit

Example:


RP/0/RSP0/CPU0:router(config-sonet)# end

or 


RP/0/RSP0/CPU0:router(config-sonet)# commit

Saves configuration changes.

  • When you issue the end command, the system prompts you to commit changes: 

    
Uncommitted changes found, commit them before exiting(yes/no/cancel)?
[cancel]:

  • Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

  • Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

  • Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

  • Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Step 10

show aps

Example:


RP/0/RSP0/CPU0:router# show aps

(Optional) Displays the operational status for all configured SONET APS groups.

Step 11

show aps group [number]

Example:


RP/0/RSP0/CPU0:router# show aps group 3

(Optional) Displays the operational status for configured SONET APS groups.

Note 

  • The show aps group command is more useful than the show aps command when multiple groups are defined.

Configuring SDH AU-3

This section includes the following tasks:

Configuring SDH AU-3 Mapped to C11-T1 or C12-E1

This task explains how to configure SDH AU-3 with c11-t1 or c12-e1 mapping.

Before you begin

Restrictions

Channelized SDH AU-3 with c11-t1 or c12-e1 mapping is supported on the following SPAs:

  • Cisco 1-Port Channelized OC-3/STM-1 SPA

  • Cisco 2-Port Channelized OC-12c/DS0 SPA

SUMMARY STEPS

  1. configure
  2. controller sonet interface-path-id
  3. clock source {internal | line}
  4. framing sdh
  5. au number
  6. mode mode
  7. root
  8. controller t1 interface-path-id
  9. channel-group number
  10. timeslots num1:num2:num3:num4
  11. or
  12. timeslots range1-range2
  13. show configuration
  14. root
  15. interface serial interface-path-id
  16. encapsulation {frame-relay | hdlc | ppp}
  17. ipv4 ip-address mask
  18. no shutdown
  19. end or commit
  20. show controllers sonet interface-path-id

DETAILED STEPS

  Command or Action Purpose
Step 1

configure

Example:

RP/0/RSP0/CPU0:router# configure

Enters global configuration mode.

Step 2

controller sonet interface-path-id

Example:

RP/0/RSP0/CPU0:router(config)# controller sonet 0/1/1/0

Enters SONET controller configuration submode and specifies the SONET controller name and interface-path-id identifier with the rack/slot/module/port notation.

Step 3

clock source {internal | line}

Example:

RP/0/RSP0/CPU0:router(config-sonet)# clock source internal

Configures the SONET port transmit clock source, where the internal keyword sets the internal clock and the line keyword sets the clock recovered from the line.

  • Use the line keyword whenever clocking is derived from the network. Use the internal keyword when two routers are connected back to back or over fiber for which no clocking is available.

  • line is the default keyword.

    Note 

    • Internal clocking is required for SRP interfaces.

Step 4

framing sdh

Example:

RP/0/RSP0/CPU0:router(config-sonet)# framing sdh

Configures the controller framing for Synchronous Digital Hierarchy (SDH) framing.

SONET framing (sonet ) is the default.

Step 5

au number

Example:

RP/0/RSP0/CPU0:router(config-sonet)# au 1

Specifies the administrative unit (AU) group and enters AU path configuration mode. For AU-3, the valid range is:

  • 1 to 3—1-Port Channelized OC-3/STM-1 SPA

  • 1 to 12—2-Port Channelized OC-12c/DS0 SPA

    Note 

    • The au command does not specify the AU type. It specifies the number of the AU group for the AU type that you want to configure. The range for the AU command varies based on whether you are configuring AU-3 or AU-4.

Step 6

mode mode

Example:

RP/0/RSP0/CPU0:router(config-auPath)# mode c11-t1

Sets the mode of interface at the AU level. AU-3 paths can be mapped to c11-t1 or c12-e1 on supported SPAs.

Step 7

root

Example:

RP/0/RSP0/CPU0:router(config-auPath)# root

Exits to global configuration mode.

Step 8

controller t1 interface-path-id

Example:

RP/0/RSP0/CPU0:router(config)# controller T1 0/1/1/0/0/0/0

Enters T1 controller configuration submode and specifies the T1 controller name and interface-path-id with the rack/slot/module/port/auNum/t1Num notation.

Step 9

channel-group number

Example:

RP/0/RSP0/CPU0:router(config-t1)# channel-group 0

Sets the channel-group number to which time slots are assigned. The range is from 1 to 28.

Step 10

timeslots num1:num2:num3:num4

Step 11

or

Step 12

timeslots range1-range2

Example:

RP/0/RSP0/CPU0:router(config-t1-channel_group)# timeslots 1:3:7:9
RP/0/RSP0/CPU0:router(config-t1-channel_group)# timeslots 1-12

Specifies time slots for the interface by number with the num1:num2:num3:num4 notation, or by range with the range1-range2 notation.

Step 13

show configuration

Example:

RP/0/RSP0/CPU0:router(config-t1-channel_group)# show configuration

Displays the contents of uncommitted configuration.

Step 14

root

Example:

RP/0/RSP0/CPU0:router(config-t3)# root

Exits to global configuration mode.

Step 15

interface serial interface-path-id

Example:

RP/0/RSP0/CPU0:router(config)# interface serial 0/1/1/0/0/0:0

Specifies the complete interface number with the rack/slot/module/port/T3Num/T1num:instance notation.

Step 16

encapsulation {frame-relay | hdlc | ppp}

Example:

RP/0/RSP0/CPU0:router(config-if)# encapsulation frame-relay

Specifies the encapsulation type with the one of the following keywords:

  • frame-relay —Frame Relay network protocol

  • hdlc —High-level Data Link Control (HDLC) synchronous protocol

  • ppp —Point-to-Point Protocol

Step 17

ipv4 ip-address mask

Example:

RP/0/RSP0/CPU0:router(config-if)# ip address 10.10.10.10 255.255.255.255

Assigns an IP address and subnet mask to the interface.

Step 18

no shutdown

Example:

RP/0/RSP0/CPU0:router(config-if)# no shutdown

Removes the shutdown configuration.

Note 

  • Removal of the shutdown configuration eliminates the forced administrative down on the interface, enabling it to move to an up or down state (assuming that the parent SONET layer is not configured administratively down).

Step 19

end or commit

Example:

RP/0/RSP0/CPU0:router(config-sonet)# end

or 


RP/0/RSP0/CPU0:router(config-sonet)# commit

Saves configuration changes.

  • When you issue the end command, the system prompts you to commit changes: 

    
Uncommitted changes found, commit them before exiting(yes/no/cancel)?
[cancel]:

  • Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

  • Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

  • Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

  • Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Step 20

show controllers sonet interface-path-id

Example:

RP/0/RSP0/CPU0:router# show controllers sonet 0/1/1/0

Verifies the SONET controller configuration.

Configuring SDH AU-3 Mapped to T3 or E3

This task explains how to configure SDH AU-3 mapped to T3 or E3.

Before you begin

Restrictions

Channelized SDH AU-3 with T3 or E3 mapping is supported on the following SPAs:

  • Cisco 1-Port Channelized OC-48/STM-16 SPA

  • Cisco 1-Port Channelized OC-3/STM-1 SPA

  • Cisco 2-Port Channelized OC-12c/DS0 SPA

SUMMARY STEPS

  1. configure
  2. controller sonet interface-path-id
  3. clock source {internal | line}
  4. framing sdh
  5. au number
  6. mode t3
  7. or
  8. mode e3
  9. root
  10. controller {t3 | e3} interface-path-id
  11. mode serial
  12. show configuration
  13. root
  14. interface serial interface-path-id
  15. encapsulation frame-relay | hdlc | ppp
  16. ipv4 ip-address mask
  17. no shutdown
  18. end or commit
  19. show controllers sonet interface-path-id

DETAILED STEPS

  Command or Action Purpose
Step 1

configure

Example:

RP/0/RSP0/CPU0:router# configure

Enters global configuration mode.

Step 2

controller sonet interface-path-id

Example:

RP/0/RSP0/CPU0:router(config)# controller sonet 0/1/1/0

Enters SONET controller configuration submode and specifies the SONET controller name and interface-path-id identifier with the rack/slot/module/port notation.

Step 3

clock source {internal | line}

Example:

RP/0/RSP0/CPU0:router(config-sonet)# clock source internal

Configures the SONET port transmit clock source, where the internal keyword sets the internal clock and the line keyword sets the clock recovered from the line.

  • Use the line keyword whenever clocking is derived from the network. Use the internal keyword when two routers are connected back to back or over fiber for which no clocking is available.

  • line is the default keyword.

    Note 

    • Internal clocking is required for SRP interfaces.

Step 4

framing sdh

Example:

RP/0/RSP0/CPU0:router(config-sonet)# framing sdh

Configures the controller framing for Synchronous Digital Hierarchy (SDH) framing.

SONET framing (sonet ) is the default.

Step 5

au number

Example:

RP/0/RSP0/CPU0:router(config-sonet)# au 1

Specifies the administrative unit (AU) group and enters AU path configuration mode. For AU-3, the valid range is:

  • 1 to 48—1-Port Channelized OC-48/DS3 SPA

  • 1 to 3—1-Port Channelized OC-3/STM-1 SPA

  • 1 to 12—2-Port Channelized OC-12c/DS0 SPA

    Note 

    • The au command does not specify the AU type. It specifies the number of the AU group for the AU type that you want to configure. The range for the AU command varies based on whether you are configuring AU-3 or AU-4.

Step 6

mode t3

Step 7

or

Step 8

mode e3

Example:

RP/0/RSP0/CPU0:router(config-auPath)# mode t3

Sets the mode of interface at the AU level to T3 or E3.

Step 9

root

Example:

RP/0/RSP0/CPU0:router(config-auPath)# root

Exits to global configuration mode.

Step 10

controller {t3 | e3} interface-path-id

Example:

RP/0/RSP0/CPU0:router(config)# controller T3 0/1/1/0/0

Enters T3 or E3 controller configuration submode and specifies the T3 or E3 controller name and interface-path-id with the rack/slot/module/port/auNum notation.

Step 11

mode serial

Example:

RP/0/RSP0/CPU0:router(config-t3)# mode serial

Configures the mode of the port to be clear channel serial.

Step 12

show configuration

Example:

RP/0/RSP0/CPU0:router(config-t3)# show configuration

Displays the contents of uncommitted configuration.

Step 13

root

Example:

RP/0/RSP0/CPU0:router(config-t3)# root

Exits to global configuration mode.

Step 14

interface serial interface-path-id

Example:

RP/0/RSP0/CPU0:router(config)# interface serial 0/1/1/0/0/0:0

Specifies the complete interface number with the rack/slot/module/port/T3Num/T1num:instance notation.

Step 15

encapsulation frame-relay | hdlc | ppp

Example:

RP/0/RSP0/CPU0:router(config-if)# encapsulation frame-relay | hdlc | ppp

Specifies the encapsulation type with the one of the following keywords:

  • frame-relay —Frame Relay network protocol

  • hdlc —High-level Data Link Control (HDLC) synchronous protocol

  • ppp —Point-to-Point Protocol

Step 16

ipv4 ip-address mask

Example:

RP/0/RSP0/CPU0:router(config-if)# ip address 10.10.10.10 255.255.255.255

Assigns an IP address and subnet mask to the interface.

Step 17

no shutdown

Example:

RP/0/RSP0/CPU0:router(config-if)# no shutdown

Removes the shutdown configuration.

Note 

  • Removal of the shutdown configuration eliminates the forced administrative down on the interface, enabling it to move to an up or down state (assuming that the parent SONET layer is not configured administratively down).

Step 18

end or commit

Example:

RP/0/RSP0/CPU0:router(config-sonet)# end

or 


RP/0/RSP0/CPU0:router(config-sonet)# commit

Saves configuration changes.

  • When you issue the end command, the system prompts you to commit changes: 

    
Uncommitted changes found, commit them before exiting(yes/no/cancel)?
[cancel]:

  • Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

  • Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

  • Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

  • Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Step 19

show controllers sonet interface-path-id

Example:

RP/0/RSP0/CPU0:router# show controllers sonet 0/1/1/0

Verifies the SONET controller configuration.

Configuring SDH AU-4

This task explains how to configure an SDH AU-4 stream into a TUG-3 channel mapped to E3s.

Before you begin

Restrictions

  • Channelized SDH is supported on the following SPAs:

    • Cisco 1-Port Channelized OC-48/STM-16 SPA

    • Cisco 1-Port Channelized OC-3/STM-1 SPA

    • Cisco 2-Port Channelized OC-12/DS0 SPA

  • In this release, AU-4 paths can only be channelized into TUG-3s.

  • The 1-Port Channelized OC-48/STM-16 SPA does not support T1 or E1 channelization.

SUMMARY STEPS

  1. configure
  2. controller sonet interface-path-id
  3. clock source {internal | line}
  4. framing sdh
  5. au number
  6. mode tug3
  7. width number
  8. tug3 number
  9. mode mode
  10. root
  11. controller name instance
  12. mode mode
  13. root
  14. controller name instance
  15. channel-group number
  16. timeslots num1:num2:num3:num4
  17. or
  18. timeslots range1-range2
  19. show configuration
  20. root
  21. interface serial interface-path-id
  22. encapsulation {frame-relay | hdlc | ppp}
  23. ipv4 ip-address mask
  24. no shutdown
  25. end or commit
  26. show controllers sonet interface-path-id

DETAILED STEPS

  Command or Action Purpose
Step 1

configure

Example:


RP/0/0/CPU0:router# configure

Enters global configuration mode.

Step 2

controller sonet interface-path-id

Example:


RP/0/0/CPU0:router(config)# controller sonet 0/1/1/0

Enters SONET controller configuration submode and specifies the SONET controller name and interface-path-id with the rack/slot/module/port notation.

Step 3

clock source {internal | line}

Example:


RP/0/0/CPU0:router(config-sonet)# clock source internal

Configures the SONET port transmit clock source, where the internal keyword sets the internal clock and the line keyword sets the clock recovered from the line.

  • Use the line keyword whenever clocking is derived from the network. Use the internal keyword when two routers are connected back to back or over fiber for which no clocking is available.

  • line is the default keyword.

    Note 

    • Internal clocking is required for SRP interfaces.

Step 4

framing sdh

Example:


RP/0/0/CPU0:router(config-sonet)# framing sdh

Configures the controller for Synchronous Digital Hierarchy (SDH) framing.

SONET framing (sonet ) is the default.

Step 5

au number

Example:


RP/0/RSP0/CPU0:router(config-sonet)# au 1

Specifies the administrative unit (AU) group and enters AU path configuration mode. For AU-4, the valid range is:

  • 1 to 16—1-Port Channelized OC-48/DS3 SPA

  • 1 to 3—1-Port Channelized OC-3/STM-1 SPA

  • 1 to 4—2-Port Channelized OC-12c/DS0 SPA

    Note 

    • The au command does not specify the AU type. It specifies the number of the AU group for the AU type that you want to configure. The range for the AU command varies based on whether you are configuring AU-3 or AU-4.

Step 6

mode tug3

Example:


RP/0/0/CPU0:router(config-auPath)# mode tug3

Sets the mode of interface at the AU level. Currently only TUG3 is supported.

Step 7

width number

Example:


RP/0/0/CPU0:router(config-auPath)# width 3

Configures the number of the AU streams.

Step 8

tug3 number

Example:


RP/0/0/CPU0:router(config-auPath)#tug3 1

Specifies the Tributary Unit Group (TUG) number and enters the config-tug3Path mode. The range is 1 to 3.

Step 9

mode mode

Example:


RP/0/0/CPU0:router(config-tug3Path)# mode e3

Sets the mode of interface at the tug3 level. The modes are:

  • c11 —TUG-3 path carrying TU-11

  • c11-t1 —TUG-3 path carrying TU-11 to T1

  • c12 —TUG-3 path carrying TU-12

  • c12-e1 —TUG-3 path carrying TU-12 to E1

  • e3 —TUG-3 path carrying E3

  • t3 —TUG-3 path carrying T3

    Note 

    • The 1-Port Channelized OC-48/STM-16 SPA only supports the e3 and t3 options.

Step 10

root

Example:


RP/0/0/CPU0:router(config-tug3Path)# root

Exits to global configuration mode.

Step 11

controller name instance

Example:


RP/0/0/CPU0:router(config)# controller e3 0/1/1/0/0/0

Enters controller configuration submode and specifies the controller name and instance identifier with the rack/slot/module/port/name/instance notation. The controller names are:

  • e3 —TUG3 path carrying E3

  • t3 —TUG3 path carrying T3

  • e1 —channelized E1 port

    Note 

    • In this step, you can create an E3 or T3 controller and add T1 channels under the T3 controller as shown inStep 14, or you can create a channelized E1 port at this point.

    • E1 is not supported on the 1-Port Channelized OC-48/STM-16 SPA.

Step 12

mode mode

Example:


RP/0/0/CPU0:router(config-e3)#mode e1

Sets the mode of interface. The modes are:

  • e1 —Channelized into 21 E1s

  • serial —Clear Channel carrying HDLC-like payload

  • t1 —Channelized into 28 T1s

    Note 

    • T1 and E1 are not supported on the 1-Port Channelized OC-48/STM-16 SPA.

Step 13

root

Example:


RP/0/0/CPU0:router(config-e3)# root

Exits to global configuration mode.

Step 14

controller name instance

Example:


RP/0/0/CPU0:router(config)# controller E1 0/1/1/0/0/0/0/0

Enters controller configuration submode and specifies the controller name and instance identifier with the rack/slot/module/port/name/instance1/instance2 notation. The controller names are:

  • serial—Clear Channel carrying HDLC-like payload.

  • t1—Channelized into 24 T1s.

Step 15

channel-group number

Example:


RP/0/0/CPU0:router(config-e1)# channel-group 0

Sets the channel-group number to which time slots are assigned.

  • For t1, the range is from 1 to 24.

  • For e1, the range is from 1 to 32.

Step 16

timeslots num1:num2:num3:num4

Step 17

or

Step 18

timeslots range1-range2

Example:


RP/0/0/CPU0:router(config-e1-channel_group)# timeslots 1:3:7:9
RP/0/0/CPU0:router(config-e1-channel_group)# timeslots 1-12

Specifies time slots for the interface by number with the num1:num2:num3:num4 notation, or by range with the range1-range2 notation.

Step 19

show configuration

Example:


RP/0/0/CPU0:router(config-e1-channel_group)# show configuration

Displays the contents of uncommitted configuration.

Step 20

root

Example:


RP/0/0/CPU0:router(config-e1-channel_group)# root

Exits to global configuration mode.

Step 21

interface serial interface-path-id

Example:


RP/0/0/CPU0:router(config)# interface serial 0/1/1/0/0/0:0

Specifies the complete interface number with the rack/slot/module/port/T3Num/T1num:instance notation.

Step 22

encapsulation {frame-relay | hdlc | ppp}

Example:


Router(config-if)# encapsulation frame-relay | hdlc | ppp

Specifies the encapsulation type with the one of the following keywords:

  • frame-relay —Frame Relay network protocol

  • hdlc —High-level Data Link Control (HDLC) synchronous protocol

  • ppp —Point-to-Point Protocol

Step 23

ipv4 ip-address mask

Example:


Router(config-if)# ip address 10.10.10.10 255.255.255.255

Assigns an IP address and subnet mask to the interface.

Step 24

no shutdown

Example:


RP/0/0/CPU0:router (config-if)# no shutdown

Removes the shutdown configuration.

Note 

  • Removal of the shutdown configuration eliminates the forced administrative down on the interface, enabling it to move to an up or down state (assuming that the parent SONET layer is not configured administratively down).

Step 25

end or commit

Example:


RP/0/0/CPU0:router(config-sonet)# end

or 


RP/0/0/CPU0:router(config-sonet)# commit

Saves configuration changes.

  • When you issue the end command, the system prompts you to commit changes: 

    
Uncommitted changes found, commit them before exiting(yes/no/cancel)?
[cancel]:

  • Entering yes saves configuration changes to the running configuration file, exits the configuration session, and returns the router to EXEC mode.

  • Entering no exits the configuration session and returns the router to EXEC mode without committing the configuration changes.

  • Entering cancel leaves the router in the current configuration session without exiting or committing the configuration changes.

  • Use the commit command to save the configuration changes to the running configuration file and remain within the configuration session.

Step 26

show controllers sonet interface-path-id

Example:


RP/0/0/CPU0:router# show controllers sonet 0/1/1/0

Verifies the SONET controller configuration.

Configuration Examples for Channelized SONET

This section contains the following examples:

Channelized SONET Examples

Channelized SONET T3 to T1 Configuration: Example

This example shows SONET T3 to T1 configuration. 


configure
controller sonet 0/1/1/0
  clock source internal
  framing sonet
  sts 1
  mode t3
  width 3
  root
 controller t3 0/1/1/0/0
  mode t1
framing auto-detect
  root
 controller t1 0/1/1/0/0/0
  framing esf
  channel-group 0
   timeslots 1:3:7:9
 show configuration
  root
 interface serial 0/1/1/0/0/0:0
 encapsulation hdlc
 ip address 10.10.10.10 255.255.255.255
 no shutdown
  commit
show controllers sonet 0/1/1/0

Channelized SONET in VT1.5 Mode and T1 Channelization to NxDS0


Note

This example is not supported on the 1-Port Channelized OC-48/STM-16 SPA.

This example shows how to configure SONET channelized to NxDS0s through SONET VT1.5 mode: 


configure
controller sonet 0/1/1/0
  clock source internal
  framing sonet
  sts 1
  mode vt15-t1
  root
controller t1 0/1/1/0/0/0
 channel-group 0 timeslots 1
  channel-group 1 timeslots 2-3
  commit

Channelized Packet over SONET Configuration: Example

This example shows Channelized Packet over SONET configuration. 


configure
 controller sonet 0/1/1/0
  clock source internal
  framing sonet
  sts 1
  mode pos scramble
  width 3
  root
 interface POS 0/1/1/0
  encapsulation hdlc
  pos crc 32
  mtu 4474
  no shutdown
 commit
show interfaces pos 0/1/1/0

SONET Clear Channel T3 Configuration: Example

This example shows SONET clear channel configuration for T3: 


configure
 controller sonet 0/1/1/0
  clock source internal
  framing sonet
  sts 1
  mode t3
  root
 controller t3 0/1/1/0/0
  mode serial
  root
 interface serial 0/1/1/0/0/0:0
 encapsulation ppp
 ip address 10.10.10.10 255.255.255.255
 no shutdown
  commit
show controllers sonet 0/1/1/0

Channelized SONET APS Multirouter Configuration: Example

This example shows SONET APS multirouter configuration. 


 aps group 1
  channel 0 local SONET 0/0/0/1
  channel 1 remote 172.18.69.123


  signalling sonet


  commit
show aps
show aps group 3

Channelized SDH Examples

Channelized SDH AU-3 Configuration: Examples

This section includes the following configuration examples

Channelized SDH AU-3 to VC-3 and Clear Channel T3/E3: Examples

This example shows how to configure SDH AU-3 to VC-3 and clear channel T3: 


configure
 controller sonet 0/1/1/0
  clock source internal
  framing sdh
  au 1
  width 1
  mode t3
  root
 controller t3 0/1/1/0/1
  mode serial
  commit

This example shows how to configure SDH AU-3 to VC-3 and clear channel E3: 


configure
 controller sonet 0/1/1/0
  clock source internal
  framing sdh
  au 1
  width 1
  mode e3
  root
 controller e3 0/1/1/0/1
  mode serial
  commit

Channelized SDH AU-3 to TUG-2, VC-11, T1 and NxDS0s: Example


Note

This example is not supported on the 1-Port Channelized OC-48/STM-16 SPA.

The following example shows how to configure SDH AU-3 to TUG-2, VC-11 and channelized T1 to NxDS0s: 


configure
 controller sonet 0/1/1/0
  clock source internal
  framing sdh
  au 1
  mode c11-t1
  width 1
  root
 controller T1 0/1/1/0/0/1/1
  channel-group 0
   timeslots 1-12
   show configuration
  root
 interface serial 0/1/1/0/1/1:0
 encapsulation ppp
 ip address 10.10.10.10 255.255.255.255
 no shutdown
 commit
show controllers sonet 0/1/1/0

Channelized SDH AU-3 to TUG-2, VC-12, E1 and NxDS0s: Example


Note

This example is not supported on the 1-Port Channelized OC-48/STM-16 SPA.

The following example shows how to configure SDH AU-3 to TUG-2, VC-12 and channelized E1 to NxDS0s: 


configure
 controller sonet 0/1/1/0
  clock source internal
  framing sdh
  au 1
  mode c12-e1
  width 1
  root
 controller e1 0/1/1/0/0/1/1
  channel-group 0
   timeslots 1-12
   show configuration
  root
 interface serial 0/1/1/0/1/1:0
 encapsulation ppp
 ip address 10.10.10.10 255.255.255.255
 no shutdown
 commit
show controllers sonet 0/1/1/0

Channelized SDH AU-4 Configuration: Examples

This section includes the following configuration examples

Channelized SDH AU-4 to TUG-3 and Clear Channel T3/E3: Examples

This example shows SDH AU-4 channelization to TUG-3 and clear channel T3: 


configure
 controller sonet 0/4/0/0
  framing sdh
  au 1
  width 3
  mode tug3
  tug3 1
   mode t3
   root
 controller t3 0/4/0/0/1/1
  mode serial
  commit

This example shows SDH AU-4 channelization to TUG-3 and clear channel E3: 


configure
 controller sonet 0/4/0/0
  framing sdh
  au 1
  width 3
  mode tug3
  tug3 1
   mode e3
   root
 controller e3 0/4/0/0/1/1
  mode serial
  commit

Channelized SDH AU-4 to TUG-3, TUG-2, and T1/E1 and NxDS0: Examples


Note

Channelization to T1/E1 and NxDS0s is not supported on the 1-Port Channelized OC-48/STM-16 SPA.

The following example shows SDH AU-4 configuration with unframed E1 controllers and serial interfaces: 


configure
 controller sonet 0/1/2/0
  framing sdh
  au 1
  width 3
  mode tug3
  tug3 1
   mode c12-e1
!
  tug3 2
   mode c12-e1
!
  tug3 3
   mode c12-e1
!
controller E1 0/1/2/0/1/1/1/1
framing unframed
!
controller E1 0/1/2/0/1/1/1/2
framing unframed
!
controller E1 0/1/2/0/1/1/1/3
framing unframed
!
interface Serial0/1/2/0/1/1/1/1:0
encapsulation ppp
multilink
  group 1
!
interface Serial0/1/2/0/1/1/1/2:0
encapsulation ppp
multilink
  group 1
!
!
interface Serial0/1/2/0/1/1/1/3:0
encapsulation ppp
multilink
  group 1
!

The following example shows SDH AU-4 configuration with E1 controller channel groups and serial interfaces: 


configure
 controller SONET0/3/2/0
   framing sdh
   au 1
   width 3
   mode tug3
   tug3 1
   mode c12-e1
!
   tug3 2
   mode c12-e1
!
   tug3 3
   mode c12-e1
!
controller E1 0/3/2/0/1/1/1/1
 framing crc4
 channel-group 0
  timeslots 1-4
!
controller E1 0/3/2/0/1/1/3/1
 framing crc4
 channel-group 0
  timeslots 1-31
!
controller E1 0/3/2/0/1/1/1/2
 framing crc4
 channel-group 0
  timeslots 1-31
!
controller E1 0/3/2/0/1/2/7/3
 framing crc4
 channel-group 0
  timeslots 1-5
!
 channel-group 1
  timeslots 6-31
!
interface Serial0/3/2/0/1/1/1/1:0
 encapsulation frame-relay IETF
 frame-relay lmi-type ansi
 frame-relay intf-type dce
!
interface Serial0/3/2/0/1/1/1/1:0.1 point-to-point
 ipv4 address 192.168.200.2 255.255.255.252
 ipv4 verify unicast source reachable-via rx
 pvc 100
  encap ietf
!
interface Serial0/3/2/0/1/1/3/1:0
 encapsulation ppp
 multilink
  group 1
!
interface Serial0/3/2/0/1/1/1/2:0
 encapsulation ppp
 multilink
  group 1