- Preface
- Optics Command Reference
- Ethernet Controller Command Reference
- Controllers OCn Command Reference
- Controllers STSn Command Reference
- Controllers STMn Command Reference
- Controllers VCn Command Reference
- ODU Controller Command Reference
- OTU Controller Command Reference
- Fabric Management Commands
- Interface GCC Command Reference
- Protection Command Reference
- Cross Connect Command Reference
- GMPLS Command Reference
- PRBS Command Reference
- Controllers Breakout Command Reference
- Patch Cord Command Reference
- Frequency Synchronization Commands
- IPv4/OSPF Commands
- IS-IS Command Reference
- L2Xconnect/VLAN/EVC Command Reference
- CFM-EOAM Command Reference
- VPWS Command Reference
- BGP Route Reflector Commands
- MPLS Traffic Engineering Commands
- Bidirectional Forwarding Commands
- Ethernet Local Management Interface Commands
- Inter-Rack Pairing Command Reference
- Smart Licensing Command Reference
- Call Home Command Reference
- System Upgrade Command Reference
- Priority Shutdown Commands
- ACL Commands
- PTP Commands
- Zero Touch Provisioning (ZTP) Commands
- Authentication, Authorization, and Accounting Commands
- Link Layer Discovery Protocol (LLDP) Command Reference
- Daisy Chain Network Command Reference
- Index
Controllers Breakout Command Reference
controller breakout (otn mode)
To configure breakout controller in otn mode, use the controller optics breakout-mode otn command in the config mode.
controller optics R/S/I/P { breakout-mode lane id} { otn } { framing framing type}
Syntax Description
controller optics |
Name of the controller |
R/S/I/P |
Displays the Rack/Slot/Instance/Port of the controller. |
breakout-mode |
Breakout mode. |
otn |
Type of the controller. |
framing |
Framing for the breakout-mode. |
Command Default
None
Command Modes
Config modeCommand History
Release | Modification |
---|---|
Release 5.2.4 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command contact your AAA administrator for assistance.
Task ID
Task ID | Operation |
---|---|
Breakout |
write |
Examples
The following example shows how to configure a breakout controller:
RP/0/RP0:hostname(config)# controller optics 0/15/0/0 breakout-mode 3 otn framing opu2
RP/0/RP0:hostname(config-optics)# commit
controller breakout (ethernet mode)
To configure breakout controller in ethernet mode, use the controller optics breakout-mode ethernet command in the config mode.
controller optics R/S/I/P { breakout-mode lane id} { ethernet } { framing framing type mapping mapping t ype}
Syntax Description
controller optics |
Name of the controller |
R/S/I/P |
Displays the Rack/Slot/Instance/Port of the controller. |
breakout-mode |
Breakout mode. |
ethernet |
Type of the controller. |
framing |
Framing for the breakout-mode. |
mapping |
Mapping for the breakout-mode. |
Command Default
None
Command Modes
Config modeCommand History
Release | Modification |
---|---|
Release 5.2.4 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command contact your AAA administrator for assistance.
Task ID
Task ID | Operation |
---|---|
Breakout |
write |
Examples
The following example shows how to configure a breakout controller:
RP/0/RP0:hostname(config)# controller optics 0/15/0/0 breakout-mode 3 ethernet framing odu2 mapping gfpf
RP/0/RP0:hostname(config-optics)# commit
controller breakout (sonet mode)
To configure breakout controller in sonet mode, use the controller optics breakout-mode sonet command in the config mode.
controller optics R/S/I/P { breakout-mode lane id} { sonet } { framing framing type mapping mapping type}
Syntax Description
controller optics |
Name of the controller |
R/S/I/P |
Displays the Rack/Slot/Instance/Port of the controller. |
breakout-mode |
Breakout mode. |
sonet |
Type of the controller. |
framing |
Framing for the breakout-mode. |
mapping |
Mapping for the breakout-mode. |
Command Default
None
Command Modes
Config modeCommand History
Release | Modification |
---|---|
Release 6.1.2.2 |
This command was introduced. |
Task ID
Task ID | Operation |
---|---|
Breakout |
write |
Examples
The following example shows how to configure a breakout controller:
RP/0/RP0:hostname(config)# controller optics 0/11/0/3 breakout-mode 1 sonet framing opu2 mapping bmp
RP/0/RP0:hostname(config-optics)# commit
controller breakout (sdh mode)
To configure breakout controller in sdh mode, use the controller optics breakout-mode sdh command in the config mode.
controller optics R/S/I/P { breakout-mode lane id} { sdh } { framing framing type mapping mapping type}
Syntax Description
controller optics |
Name of the controller |
R/S/I/P |
Displays the Rack/Slot/Instance/Port of the controller. |
breakout-mode |
Breakout mode. |
sdh |
Type of the controller. |
framing |
Framing for the breakout-mode. |
mapping |
Mapping for the breakout-mode. |
Command Default
None
Command Modes
Config modeCommand History
Release | Modification |
---|---|
Release 6.1.2.2 |
This command was introduced. |
Task ID
Task ID | Operation |
---|---|
Breakout |
write |
Examples
The following example shows how to configure a breakout controller:
RP/0/RP0:hostname(config)# controller optics 0/11/0/3 breakout-mode 1 sdh framing opu2 mapping bmp
RP/0/RP0:hostname(config-optics)# commit
controller breakout (LAN PHY mode)
To configure breakout controller in LAN PHY mode, use the controller optics breakout-mode ethernet framing packet command in the config mode.
controller optics R/S/I/P breakout-mode lane id ethernet framing packet
Syntax Description
controller optics |
Name of the controller |
R/S/I/P |
Enter the Rack/Slot/Instance/Port of the breakout controller. |
breakout-mode |
Breakout mode. |
ethernet |
Type of the controller. |
framing packet |
Set framing type as packet. |
Command Default
None
Command Modes
Config modeCommand History
Release | Modification |
---|---|
Release 6.1.36 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command contact your AAA administrator for assistance.
Task ID
Task ID | Operation |
---|---|
Breakout |
write |
Examples
The following example shows how to configure a HundredGigE 0/15/0/0/3 breakout controller in LAN PHY mode:
RP/0/RP0:hostname(config)# controller optics 0/15/0/0 breakout-mode 3 ethernet framing packet
RP/0/RP0:hostname(config-optics)# commit
show breakout-mode
show controller optics R/S/I/P { breakout-mode lane lane number} { capability}
Syntax Description
optics |
Name of the port. |
lane number |
Displays the Rack/Slot/Instance/Port of the controller. |
breakout-mode |
Breakout mode. |
lane |
Displays the lane number. |
Command Default
None
Command Modes
Exec modeCommand History
Release | Modification |
---|---|
Release 5.2.4.6 |
This command was introduced. |
Usage Guidelines
To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command contact your AAA administrator for assistance.
Task ID
Task ID | Operation |
---|---|
Breakout |
write |
Examples
The following example shows how to configure a breakout controller.
RP/0/RP0:hostname# show controller optics 0/0/0/1 breakout-mode lane 1 capabilities
BreakOut Information -------------------------------------------------- Port_no Breakout Type Framing Mapping PT type Rate 0 Ethernet OPU2 framing type GFP-F mapping type 05 (GFP mapping) None 0 Ethernet OPU2 framing type GFP-F-Extended mapping type 09 (GFP mapping into OPU2) None 0 Ethernet OPU Flex framing type GFP-F mapping type 09 (GFP mapping into OPU2) 10GE 0 Ethernet OPU Flex framing type GFP-F mapping type 09 (GFP mapping into OPU2) None 0 OTN OPU2 framing type None mapping type Traffic Dependent None 0 OTN OPU2e framing type None mapping type Traffic Dependent None 0 OTN OPU1f framing type None mapping type Traffic Dependent None 0 OTN OPU2f framing type None mapping type Traffic Dependent None 0 Ethernet Packet framing type None mapping type NA 10GE RP/0/RP0:SIT06#
RP/0/RP0:hostname# show controller optics 0/0/0/1 breakout-mode lane 1 configured
BreakOut Information -------------------------------------------------- Breakout type Lane Framing Mapping PT type Rate Ethernet 1 OPU2 framing type GFP-F mapping type 05 (GFP mapping) None RP/0/RP0:SIT06#