Firepower Management Center Configuration Guide, Version 6.0.1

Introduction to Reusable Objects

For increased flexibility and web interface ease-of-use, the Firepower System uses named objects, which are reusable configurations that associate a name with a value. When you want to use that value, use the named object instead. The system supports object use in various places in the web interface, including many policies and rules, event searches, reports, dashboards, and so on. The system provides many predefined objects that represent frequently used configurations.

Use the object manager to create and manage objects. Many configurations that use objects also allow you to create objects on the fly, as needed. You can also use the object manager to:

View the policies, settings, and other objects where a network, port, VLAN, or URL object is used; see Viewing Objects and Their Usage.
Group objects to reference multiple objects with a single configuration; see Object Groups.
Override object values for selected devices or, in a multidomain deployment, selected domains; see Object Overrides.

After you edit an object used in an active policy, you must redeploy the changed configuration for your changes to take effect. You cannot delete an object that is in use by an active policy.

Note

An object is configured on a managed device if, and only if, the object is used in a policy that is assigned to that device. If you remove an object from all policies assigned to a given device, the object is also removed from the device configuration on the next deployment, and subsequent changes to the object are not reflected in the device configuration.

Object Types

The following table lists the objects you can create in the Firepower System, and indicates whether each object type can be grouped or configured to allow overrides.


Object Type	Groupable?	Allows Overrides?
Network	yes	yes
Port	yes	yes
Security Zone	no	no
Application Filter	no	no
VLAN Tag	yes	yes
URL	yes	yes
Geolocation	no	no
Variable Set	no	no
Security Intelligence: Network, DNS, and URL lists and feeds	no	no
Sinkhole	no	no
File List	no	no
Cipher Suite List	no	no
Distinguished Name	yes	no
Public Key Infrastructure (PKI): Internal and Trusted CA Internal and External Certs	yes	no
SLA Monitor	no	no
Prefix List: IPv4 and IPv6	no	yes
Route Map	no	yes
Access List: Standard and Extended	no	yes
AS Path	no	yes
Community List	no	yes
Policy List	no	yes

Objects and Multitenancy

In a multidomain deployment, you can create objects in Global and descendant domains. The system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which you cannot edit, with the exception of security zones.

Note

Because security zones are tied to device interfaces, which you configure at the leaf level, administrators in descendant domains can view and edit security zones created in ancestor domains. Subdomain users can add and delete interfaces from ancestor zones, but cannot delete or rename the zones.

Object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.

For objects that support grouping, you can group objects in the current domain with objects inherited from ancestor domains.

Object overrides allow you to define device-specific or domain-specific values for certain types of object, including network, port, VLAN tag, and URL. In a multidomain deployment, you can define a default value for an object in an ancestor domain, but allow administrators in descendant domains to add override values for that object.

The Object Manager

You can use the object manager to create and manage objects and object groups.

The object manager displays 20 objects or groups per page. If you have more than 20 of any type of object or group, use the navigation links at the bottom of the page to view additional pages. You can also go to a specific page or click Refresh ( refresh icon ) to refresh your view.

By default, the page lists objects and groups alphabetically by name. You can filter the objects on the page by name or value.

Editing Objects

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose an object type from the list; see Introduction to Reusable Objects.
Step 3	Click Edit () next to the object you want to edit. If View () appears instead, the object belongs to an ancestor domain and has been configured not to allow overrides, or you do not have permission to modify the object.
Step 4	Modify the object settings as desired.
Step 5	If you are editing a variable set, manage the variables in the set; see Managing Variables.
Step 6	For objects that can be configured to allow overrides: If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides. You can change this setting only for objects that belong to the current domain. If you want to add override values to this object, expand the Override section and click Add; see Adding Object Overrides.
Step 7	Click Save.
Step 8	If you are editing a variable set, and that set is in use by an access control policy, click Yes to confirm that you want to save your changes.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Viewing Objects and Their Usage

You can view usage details of objects on the Object Management page. The network, port, VLAN, and URL object types are the only object types that provide this functionality.

Note

In a multidomain deployment, you can view objects from any other domain. However, to find usage of objects in a descendant domain, switch to that domain.

Procedure

Step 1

Choose Objects > Object Management.

Step 2

Choose one of the following object types:

Network
Port
VLAN Tag
URL

Step 3

Click Find Usage ( find usage icon ) next to the object.

The Object Usage window displays a list of all the policies, objects, and other settings where the object is in use. Click any of the listed items to know more about the object usage. For policies and some other settings where the object is used, you can click the corresponding links to visit the respective UI pages.

Filtering Objects or Object Groups

In a multidomain deployment, the system displays objects created in the current and ancestor domains, which you can filter.

Procedure

Step 1

Choose Objects > Object Management.

Step 2

Enter your filter criteria in the Filter field.

The page updates as you type to display matching items.

You can use the following wildcards:

The asterisk (*) matches zero or more occurrences of a character.
The caret (^) matches content at the beginning of a string.
The dollar sign ($) matches content at the end of a string.

Object Groups

Grouping objects allows you to reference multiple objects with a single configuration. The system allows you to use objects and object groups interchangeably in the web interface. For example, anywhere you would use a port object, you can also use a port object group.

You can group network, port, VLAN tag, URL, and PKI objects.

Objects and object groups of the same type cannot have the same name. In a multidomain deployment, the names of object groups must be unique within the domain hierarchy. Note that the system may identify a conflict with the name of an object group you cannot view in your current domain.

When you edit an object group used in a policy (for example, a network object group used in an access control policy), you must re-deploy the changed configuration for your changes to take effect.

Deleting a group does not delete the objects in the group, just their association with each other. Additionally, you cannot delete a group that is in use in an active policy. For example, you cannot delete a VLAN tag group that you are using in a VLAN condition in a saved access control policy.

Grouping Reusable Objects

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

You can group objects in the current domain with objects inherited from ancestor domains.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	If the object type you want to group is Network, Port, URL, or VLAN Tag: Choose the object type from the list of object types. Choose Add Group from the Add [Object Type] drop-down list.
Step 3	If the object type you want to group is Distinguished Name: Expand the Distinguished Name node. Choose Object Groups. Click Add Distinguished Name Group.
Step 4	If the object type you want to group is PKI: Expand the PKI node. Choose one of the following: Internal CA Groups Trusted CA Groups Internal Cert Groups External Cert Groups Click Add [Object Type] Group.
Step 5	Enter a unique Name.
Step 6	Choose one or more objects from the list, and click Add. You can also: Use the filter field Search () to search for existing objects to include, which updates as you type to display matching items. Click Reload () above the search field or click Clear () in the search field to clear the search string. Click Add () to create objects on the fly if no existing objects meet your needs.
Step 7	Optionally for Network, Port, URL, and VLAN Tag groups: Enter a Description. Check the Allow Overrides check box to allow overrides for this object group; see Allowing Object Overrides.
Step 8	Click Save.

What to do next

If an active policy references your object group, deploy configuration changes; see Deploy Configuration Changes.

Object Overrides

An object override allows you to define an alternate value for an object, which the system uses for the devices you specify.

You can create an object whose definition works for most devices, and then use overrides to specify modifications to the object for the few devices that need different definitions. You can also create an object that needs to be overridden for all devices, but its use allows you to create a single policy for all devices. Object overrides allow you to create a smaller set of shared policies for use across devices without giving up the ability to alter policies when needed for individual devices.

For example, you might want to deny ICMP traffic to the different departments in your company, each of which is connected to a different network. You can do this by defining an access control policy with a rule that includes a network object called Departmental Network. By allowing overrides for this object, you can then create overrides on each relevant device that specifies the actual network where that device is connected.

In a multidomain deployment, you can define a default value for an object in an ancestor domain and allow administrators in descendant domains to add override values for that object. For example, a managed security service provider (MSSP) might use a single Firepower Management Center to manage network security for multiple customers. Administrators at the MSSP can define an object in the Global domain for use in all customers' deployments. Administrators for each customer can log into descendant domains to override that object for their organizations. These local administrators cannot view or affect the override values of other customers of the MSSP.

You can target an object override to a specific domain. In this case, the system uses the object override value for all devices in the targeted domain unless you override it at the device level.

From the object manager, you can choose an object that can be overridden and define a list of device-level or domain-level overrides for that object.

You can use object overrides with the following object types only:

Network
Port
VLAN tag
URL
SLA Monitor
Prefix List
Route Map
Access List
AS Path
Community List
Policy List

If you can override an object, the Override column appears for the object type in the object manager. Possible values for this column include:

Green checkmark — indicates that you can create overrides for the object and no overrides have been added yet
Red X — indicates that you cannot create overrides for the object
Number — represents a count of the overrides that have been added to that object (for example, "2" indicates two overrides have been added)

Managing Object Overrides

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose from the list of object types; see Introduction to Reusable Objects.
Step 3	Click Edit () next to the object you want to edit. If View () appears instead, the object belongs to an ancestor domain and has been configured not to allow overrides, or you do not have permission to modify the object.
Step 4	Manage the object overrides: Add—Add object overrides; see Adding Object Overrides. Allow—Allow object overrides; see Allowing Object Overrides. Delete—In the object editor, click Delete () next to the override you want to remove. Edit—Edit object overrides; see Editing Object Overrides.

Allowing Object Overrides

Procedure

Step 1	In the object editor, check the Allow Overrides check box.
Step 2	Click Save.

What to do next

Add object override values; see Adding Object Overrides.

Adding Object Overrides

Before you begin

Allow object overrides; see Allowing Object Overrides.

Procedure

Step 1	In the object editor, expand the Override section.
Step 2	Click Add.
Step 3	On Targets, choose domains or devices in the Available Devices and Domains list and click Add.
Step 4	On the Override tab, enter a Name.
Step 5	Optionally, enter a Description.
Step 6	Enter an override value. Example: For a network object, enter a network value.
Step 7	Click Add.
Step 8	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Editing Object Overrides

You can modify the description and the value of an existing override, but you cannot modify the existing target list. Instead, you must add a new override with new targets, which replaces the existing override.

Procedure

Step 1	In the object editor, expand the Override section.
Step 2	Click Edit () next to the override you want to modify.
Step 3	Optionally, modify the Description.
Step 4	Modify the override value.
Step 5	Click Save to save the override.
Step 6	Click Save to save the object.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Network Objects

A network object represents one or more IP addresses that you can specify either individually or as address blocks. You can use network objects and groups in various places in the system’s web interface, including access control policies, network variables, identity rules, network discovery rules, event searches, reports, and so on.

Creating Network Objects

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose Network from the list of object types.
Step 3	Choose Add Object from the Add Network drop-down menu.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Optionally, enter a Description.
Step 6	In the Network field, enter an IP address or address block to add to the object.
Step 7	Manage overrides for the object: If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides. If you want to add override values to this object, expand the Override section and click Add; see Adding Object Overrides.
Step 8	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Port Objects

Port objects represent different protocols in slightly different ways:

TCP and UDP

A port object represents the transport layer protocol, with the protocol number in parentheses, plus an optional associated port or port range. For example: TCP(6)/22.

ICMP and ICMPv6 (IPv6-ICMP)

A port object represents the Internet layer protocol plus an optional type and code. For example: ICMP(1):3:3.

You can restrict an ICMP or IPV6-ICMP port object by type and, if applicable, code. For more information on ICMP types and codes, see:

Other

A port object can represent other protocols that do not use ports.

The Firepower System provides default port objects for well-known ports. You cannot modify or delete these default objects. You can create custom port objects in addition to the default objects.

You can use port objects and groups in various places in the system’s web interface, including access control policies, identity rules, network discovery rules, port variables, and event searches. For example, if your organization uses a custom client that uses a specific range of ports and causes the system to generate excessive and misleading events, you can configure your network discovery policy to exclude monitoring those ports.

When using port objects, observe the following guidelines:

You cannot add any protocol other than TCP or UDP for source port conditions in access control rules. Also, you cannot mix transport protocols when setting both source and destination port conditions in a rule.
If you add an unsupported protocol to a port object group used in a source port condition, the rule where it is used does not take affect on the managed device when the configuration is deployed.
If you create a port object containing both TCP and UDP ports, then add it as a source port condition in a rule, you cannot add a destination port, and vice versa.

Creating Port Objects

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose Port from the list of object types.
Step 3	Choose Add Object from the Add Port drop-down list.
Step 4	Enter a Name.
Step 5	Choose a Protocol.
Step 6	Depending on the protocol you chose, constrain by Port, or choose an ICMP Type and Code. You can enter ports from `1` to `65535`. Use a hyphen to specify a port range. You must constrain the object by port if you chose to match All protocols, using the Other drop-down list.
Step 7	Manage overrides for the object: If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides. If you want to add override values to this object, expand the Override section and click Add; see Adding Object Overrides.
Step 8	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Application Filters

System-provided application filters help you perform application control by organizing applications according to basic characteristics: type, risk, business relevance, category, and tags. In the object manager, you can create and manage reuseable user-defined application filters based on combinations of the system-provided filters, or on custom combinations of applications. For detailed information, see Application Conditions (Application Control).

VLAN Tag Objects

Each VLAN tag object you configure represents a VLAN tag or range of tags.

You can group VLAN tag objects. Groups represent multiple objects; using a range of VLAN tags in a single object is not considered a group in this sense.

You can use VLAN tag objects and groups in various places in the system’s web interface, including rules and event searches. For example, you could write an access control rule that applies only to a specific VLAN.

Creating VLAN Tag Objects

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose VLAN Tag from the list of object types.
Step 3	Choose Add Object from the Add VLAN Tag drop-down list.
Step 4	Enter a Name.
Step 5	Enter a Description.
Step 6	Enter a value in the VLAN Tag field. Use a hyphen to specify a range of VLAN tags.
Step 7	Manage overrides for the object: If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides. If you want to add override values to this object, expand the Override section and click Add; see Adding Object Overrides.
Step 8	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

URL Objects

Important

For best practices for using this and similar options in Security Intelligence configurations and for URL rules in access control policies, see Manual URL Filtering Options.

A URL object defines a single URL or IP address, whereas a URL group object can define more than one URL or address. You can use URL objects and groups in various places in the system’s web interface, including access control policies and event searches.

The system makes a simple substring match on any URL that you enter, which may not necessarily be what you expect. See matching example URLs at Manual URL Filtering Options.

When creating URL objects, especially if you do not configure SSL inspection to decrypt or block encrypted traffic, keep the following points in mind:

If you plan to use a URL object to match HTTPS traffic in an access control rule, create the object using the subject common name in the public key certificate used to encrypt the traffic. Also, the system disregards subdomains within the subject common name, so do not include subdomain information. For example, use example.com rather than www.example.com.
When matching web traffic using access control rules with URL conditions, the system disregards the encryption protocol (HTTP vs HTTPS). In other words, if you block a website, both HTTP and HTTPS traffic to that website is blocked, unless you use an application condition to refine the rule. When creating a URL object, you do not need to specify the protocol when creating an object. For example, use example.com rather than http://example.com/.

Creating URL Objects

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose URL from the list of object types.
Step 3	Choose Add Object from the Add URL drop-down list.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Optionally, enter a Description.
Step 6	Enter the URL or IP address.
Step 7	Manage overrides for the object: If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides. If you want to add override values to this object, expand the Override section and click Add; see Adding Object Overrides.
Step 8	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Geolocation Objects

Each geolocation object you configure represents one or more countries or continents that the system has identified as the source or destination of traffic on your monitored network. You can use geolocation objects in various places in the system’s web interface, including access control policies, SSL policies, and event searches. For example, you could write an access control rule that blocks traffic to or from certain countries.

To ensure that you are using up-to-date information to filter your network traffic, Cisco strongly recommends that you regularly update your Geolocation Database (GeoDB).

Creating Geolocation Objects

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose Geolocation from the list of object types.
Step 3	Click Add Geolocation.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Check the check boxes for the countries and continents you want to include in your geolocation object. Checking a continent chooses all countries within that continent, as well as any countries that GeoDB updates may add under that continent in the future. Unchecking any country under a continent unchecks the continent. You can choose any combination of countries and continents.
Step 6	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Security Zones

Security zones segment your network to help you manage and classify traffic flow. A security zone simply groups interfaces. These groups may span multiple devices; you can also configure multiple zones on a single device.

All interfaces in a security zone must be of the same type: all inline, passive, switched, routed, or ASA FirePOWER. After you create a security zone, you cannot change the type of interfaces it contains. An interface can belong to only one zone.

The Security Zones page of the object manager lists the zones configured on your managed devices. The page also displays the type of interfaces in each zone, and you can expand each zone to view which interfaces on which devices belong to each zone.

Note

Create inline sets before you add security zones for the interfaces in the inline set; otherwise security zones are removed and you must add them again.

Model-Specific Notes and Warnings

During initial configuration of a 7000 or 8000 Series device, the system creates security zones based on the detection mode you selected for the device. For example, the system creates a Passive zone in passive deployments, while in inline deployments the system creates External and Internal zones. When you register the device to the Firepower Management Center, those security zones are added to the FMC.

Zones and Multitenancy

In a multidomain deployment, you can create security zones at any level. A zone created in an ancestor domain can contain interfaces that reside on devices in different domains. In this situation, subdomain users viewing the ancestor zone configuration in the object manager can see only the interfaces in their domain.

Unless restricted by role, subdomain users can view and edit zones created in ancestor domains. Subdomain users can add and delete interfaces from these zones. They cannot, however, delete or rename the zones. You can neither view nor edit zones created in descendant domains.

Creating Security Zone Objects

Tip

You can create empty security zones and add interfaces to them later. To add an interface, the interface must have a name. You can also create security zones while configuring interfaces in Devices > Device Management.

Before you begin

Understand the usage requirements and restrictions for each type of security zone. See Security Zones.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose Security Zones from the list of object types.
Step 3	Click Add Security Zone.
Step 4	Enter a Name.
Step 5	Choose an Interface Type.
Step 6	From the Device > Interfaces drop-down list, choose a device that contains interfaces you want to add.
Step 7	Choose one or more interfaces.
Step 8	Click Add to add the interfaces you chose, grouped by device.
Step 9	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Variable Sets

Variables represent values commonly used in intrusion rules to identify source and destination IP addresses and ports. You can also use variables in intrusion policies to represent IP addresses in rule suppressions, adaptive profiles, and dynamic rule states.

Tip

Preprocessor rules can trigger events regardless of the hosts defined by network variables used in intrusion rules.

You use variable sets to manage, customize, and group your variables. You can use the default variable set provided by the system or create your own custom sets. Within any set you can modify predefined default variables and add and modify user-defined variables.

Most of the shared object rules and standard text rules that the Firepower System provides use predefined default variables to define networks and port numbers. For example, the majority of the rules use the variable $HOME_NET to specify the protected network and the variable $EXTERNAL_NET to specify the unprotected (or outside) network. In addition, specialized rules often use other predefined variables. For example, rules that detect exploits against web servers use the $HTTP_SERVERS and $HTTP_PORTS variables.

Rules are more effective when variables more accurately reflect your network environment. At a minimum, you should modify default variables in the default set. By ensuring that a variable such as $HOME_NET correctly defines your network and $HTTP_SERVERS includes all web servers on your network, processing is optimized and all relevant systems are monitored for suspicious activity.

To use your variables, you link variable sets to intrusion policies associated with access control rules or with the default action of an access control policy. By default, the default variable set is linked to all intrusion policies used by access control policies.

Adding a variable to any set adds it to all sets; that is, each variable set is a collection of all variables currently configured on your system. Within any variable set, you can add user-defined variables and customize the value of any variable.

Initially, the Firepower System provides a single, default variable set comprised of predefined default values. Each variable in the default set is initially set to its default value, which for a predefined variable is the value set by the Cisco Talos Intelligence Group (Talos) and provided in rule updates.

Although you can leave predefined default variables configured to their default values, Cisco recommends that you modify a subset of predefined variables.

You could work with variables only in the default set, but in many cases you can benefit most by adding one or more custom sets, configuring different variable values in different sets, and perhaps even adding new variables.

When using multiple sets, it is important to remember that the current value of any variable in the default set determines the default value of the variable in all other sets.

When you select Variable Sets on the Object Manager page, the object manager lists the default variable set and any custom sets you created.

On a freshly installed system, the default variable set is comprised only of the default variables predefined by Cisco.

Each variable set includes the default variables provided by the system and all custom variables you have added from any variable set. Note that you can edit the default set, but you cannot rename or delete the default set.

In a multidomain deployment, the system generates a default variable set for each subdomain.

Caution

Importing an access control or an intrusion policy overwrites existing default variables in the default variable set with the imported default variables. If your existing default variable set contains a custom variable not present in the imported default variable set, the unique variable is preserved.

Variable Sets in Intrusion Policies

By default, the Firepower System links the default variable set to all intrusion policies used in an access control policy. When you deploy an access control policy that uses an intrusion policy, intrusion rules that you have enabled in the intrusion policy use the variable values in the linked variable set.

When you modify a custom variable set used by an intrusion policy in an access control policy, the system reflects the status for that policy as out-of-date on the Access Control Policy page. You must re-deploy the access control policy to implement changes in your variable set. When you modify the default set, the system reflects the status of all access control policies that use intrusion policies as out-of-date, and you must re-deploy all access control policies to implement your changes.

Variables

Variables belong to one of the following categories:

Default Variables

Variables provided by the Firepower System. You cannot rename or delete a default variable, and you cannot change its default value. However, you can create a customized version of a default variable.

Customized Variables

Variables you create. These variables can include:

customized default variables

When you edit the value for a default variable, the system moves the variable from the Default Variables area to the Customized Variables area. Because variable values in the default set determine the default values of variables in custom sets, customizing a default variable in the default set modifies the default value of the variable in all other sets.
user-defined variables

You can add and delete your own variables, customize their values within different variable sets, and reset customized variables to their default values. When you reset a user-defined variable, it remains in the Customized Variables area.

User-defined variables can be one of the following types:
- network variables specify the IP addresses of hosts in your network traffic.
- port variables specify TCP or UDP ports in network traffic, including the value any for either type.

For example, if you create custom standard text rules, you might also want to add your own user-defined variables to more accurately reflect your traffic or as shortcuts to simplify the rule creation process. Alternatively, if you create a rule that you want to inspect traffic in the “demilitarized zone” (or DMZ) only, you can create a variable named $DMZ whose value lists the server IP addresses that are exposed. You can then use the $DMZ variable in any rule written for this zone.

Advanced Variables

Variables provided by the Firepower System under specific conditions. These variables have a very limited deployment.

Predefined Default Variables

By default, the Firepower System provides a single default variable set, which is comprised of predefined default variables. The Cisco Talos Intelligence Group (Talos) uses rule updates to provide new and updated intrusion rules and other intrusion policy elements, including default variables.

Because many intrusion rules provided by the system use predefined default variables, you should set appropriate values for these variables. Depending on how you use variable sets to identify traffic on your network, you can modify the values for these default variables in any or all variable sets.

Caution

Importing an access control or an intrusion policy overwrites existing default variables in the default variable set with the imported default variables. If your existing default variable set contains a custom variable not present in the imported default variable set, the unique variable is preserved.

The following table describes the variables provided by the system and indicates which variables you typically would modify. For assistance determining how to tailor variables to your network, contact Professional Services or Support.

Table 1. System-Provided Variables
Variable Name	Description	Modify?
`$AIM_SERVERS`	Defines known AOL Instant Messenger (AIM) servers, and is used in chat-based rules and rules that look for AIM exploits.	Not required.
`$DNS_SERVERS`	Defines Domain Name Service (DNS) servers. If you create a rule that affects DNS servers specifically, you can use the `$DNS_SERVERS` variable as a destination or source IP address.	Not required in current rule set.
`$EXTERNAL_NET`	Defines the network that the Firepower System views as the unprotected network, and is used in many rules to define the external network.	Yes, you should adequately define `$HOME_NET` and then exclude `$HOME_NET` as the value for `$EXTERNAL_NET.`
`$FILE_DATA_PORTS`	Defines non-encrypted ports used in intrusion rules that detect files in a network stream.	Not required.
`$FTP_PORTS`	Defines the ports of FTP servers on your network, and is used for FTP server exploit rules.	Yes, if your FTP servers use ports other than the default ports (you can view the default ports in the web interface).
`$GTP_PORTS`	Defines the data channel ports where the packet decoder extracts the payload inside a GTP (General Packet Radio Service [GPRS] Tunneling Protocol) PDU.	Not required.
`$HOME_NET`	Defines the network that the associated intrusion policy monitors, and is used in many rules to define the internal network.	Yes, to include the IP addresses for your internal network.
`$HTTP_PORTS`	Defines the ports of web servers on your network, and is used for web server exploit rules.	Yes, if your web servers use ports other than the default ports (you can view the default ports in the web interface).
`$HTTP_SERVERS`	Defines the web servers on your network. Used in web server exploit rules.	Yes, if you run HTTP servers.
`$ORACLE_PORTS`	Defines Oracle database server ports on your network, and is used in rules that scan for attacks on Oracle databases.	Yes, if you run Oracle servers.
`$SHELLCODE_PORTS`	Defines the ports you want the system to scan for shell code exploits, and is used in rules that detect exploits that use shell code.	Not required.
`$SIP_PORTS`	Defines the ports of SIP servers on your network, and is used for SIP exploit rules.	Not required.
`$SIP_SERVERS`	Defines SIP servers on your network, and is used in rules that address SIP-targeted exploits.	Yes, if you run SIP servers, you should adequately define `$HOME_NET` and then include `$HOME_NET` as the value for `$SIP_SERVERS.`
`$SMTP_SERVERS`	Defines SMTP servers on your network, and is used in rules that address exploits that target mail servers.	Yes, if you run SMTP servers.
`$SNMP_SERVERS`	Defines SNMP servers on your network, and is used in rules that scan for attacks on SNMP servers.	Yes, if you run SNMP servers.
`$SNORT_BPF`	Identifies a legacy advanced variable that appears only when it existed on your system in a Firepower System software release before Version 5.3.0 that you subsequently upgraded to Version 5.3.0 or greater.	No, you can only view or delete this variable. You cannot edit it or recover it after deleting it.
`$SQL_SERVERS`	Defines database servers on your network, and is used in rules that address database-targeted exploits.	Yes, if you run SQL servers.
`$SSH_PORTS`	Defines the ports of SSH servers on your network, and is used for SSH server exploit rules.	Yes, if your SSH servers use ports other than the default port (you can view the default ports in the web interface).
`$SSH_SERVERS`	Defines SSH servers on your network, and is used in rules that address SSH-targeted exploits.	Yes, if you run SSH servers, you should adequately define `$HOME_NET` and then include `$HOME_NET` as the value for `$SSH_SERVERS.`
`$TELNET_SERVERS`	Defines known Telnet servers on your network, and is used in rules that address Telnet server-targeted exploits.	Yes, if you run Telnet servers.
`$USER_CONF`	Provides a general tool that allows you to configure one or more features not otherwise available via the web interface. Conflicting or duplicate `$USER_CONF` configurations will halt the system.	No, only as instructed in a feature description or with the guidance of Support.

Network Variables

Network variables represent IP addresses you can use in intrusion rules that you enable in an intrusion policy and in intrusion policy rule suppressions, dynamic rule states, and adaptive profiles. Network variables differ from network objects and network object groups in that network variables are specific to intrusion policies and intrusion rules, whereas you can use network objects and groups to represent IP addresses in various places in the system’s web interface, including access control policies, network variables, intrusion rules, network discovery rules, event searches, reports, and so on.

You can use network variables in the following configurations to specify the IP addresses of hosts on your network:

intrusion rules—Intrusion rule Source IPs and Destination IPs header fields allow you to restrict packet inspection to the packets originating from or destined to specific IP addresses.
suppressions—The Network field in source or destination intrusion rule suppressions allows you to suppress intrusion event notifications when a specific IP address or range of IP addresses triggers an intrusion rule or preprocessor.
dynamic rule states—The Network field in source or destination dynamic rule states allows you to detect when too many matches for an intrusion rule or preprocessor rule occur in a given time period.
adaptive profiles—The adaptive profiles Networks field identifies hosts where you want to improve reassembly of packet fragments and TCP streams in passive deployments.

When you use variables in the fields identified in this section, the variable set you link to an intrusion policy determines the variable values in the network traffic handled by an access control policy that uses the intrusion policy.

You can add any combination of the following network configurations to a variable:

any combination of network variables, network objects, and network object groups that you select from the list of available networks
individual network objects that you add from the New Variable or Edit Variable page, and can then add to your variable and to other existing and future variables
literal, single IP addresses or address blocks

You can list multiple literal IP addresses and address blocks by adding each individually. You can list IPv4 and IPv6 addresses and address blocks alone or in any combination. When specifying IPv6 addresses, you can use any addressing convention defined in RFC 4291.

The default value for included networks in any variable you add is the word any, which indicates any IPv4 or IPv6 address. The default value for excluded networks is none, which indicates no network. You can also specify the address :: in a literal value to indicate any IPv6 address in the list of included networks, or no IPv6 addresses in the list of exclusions.

Adding networks to the excluded list negates the specified addresses and address blocks. That is, you can match any IP address with the exception of the excluded IP address or address blocks.

For example, excluding the literal address 192.168.1.1 specifies any IP address other than 192.168.1.1, and excluding 2001:db8:ca2e::fa4c specifies any IP address other than 2001:db8:ca2e::fa4c.

You can exclude any combination of networks using literal or available networks. For example, excluding the literal values 192.168.1.1and 192.168.1.5 includes any IP address other than 192.168.1.1 or 192.168.1.5. That is, the system interprets this as “not 192.168.1.1 and not 192.168.1.5,” which matches any IP address other than those listed between brackets.

Note the following points when adding or editing network variables:

You cannot logically exclude the value any which, if excluded, would indicate no address. For example, you cannot add a variable with the value any to the list of excluded networks.
Network variables identify traffic for the specified intrusion rule and intrusion policy features. Note that preprocessor rules can trigger events regardless of the hosts defined by network variables used in intrusion rules.
Excluded values must resolve to a subset of included values. For example, you cannot include the address block 192.168.5.0/24 and exclude 192.168.6.0/24.

Port Variables

Port variables represent TCP and UDP ports you can use in the Source Port and Destination Port header fields in intrusion rules that you enable in an intrusion policy. Port variables differ from port objects and port object groups in that port variables are specific to intrusion rules. You can create port objects for protocols other than TCP and UDP, and you can use port objects in various places in the system’s web interface, including port variables, access control policies, network discovery rules, and event searches.

You can use port variables in the intrusion rule Source Port and Destination Port header fields to restrict packet inspection to packets originating from or destined to specific TCP or UDP ports.

When you use variables in these fields, the variable set you link to the intrusion policy associated with an access control rule or policy determines the values for these variables in the network traffic where you deploy the access control policy.

You can add any combination of the following port configurations to a variable:

any combination of port variables and port objects that you select from the list of available ports

Note that the list of available ports does not display port object groups, and you cannot add these to variables.
individual port objects that you add from the New Variable or Edit Variable page, and can then add to your variable and to other existing and future variables

Only TCP and UDP ports, including the value any for either type, are valid variable values. If you use the new or edit variables page to add a valid port object that is not a valid variable value, the object is added to the system but is not displayed in the list of available objects. When you use the object manager to edit a port object that is used in a variable, you can only change its value to a valid variable value.
single, literal port values and port ranges

You must separate port ranges with a dash (-). Port ranges indicated with a colon (:) are supported for backward compatibility, but you cannot use a colon in port variables that you create.

You can list multiple literal port values and ranges by adding each individually in any combination.

Note the following points when adding or editing port variables:

The default value for included ports in any variable you add is the word any, which indicates any port or port range. The default value for excluded ports is none, which indicates no ports.

Tip

To create a variable with the value any, name and save the variable without adding a specific value.

You cannot logically exclude the value any which, if excluded, would indicate no ports. For example, you cannot save a variable set when you add a variable with the value any to the list of excluded ports.
Adding ports to the excluded list negates the specified ports and port ranges. That is, you can match any port with the exception of the excluded ports or port ranges.
Excluded values must resolve to a subset of included values. For example, you cannot include the port range 10-50 and exclude port 60.

Advanced Variables

Advanced variables allow you to configure features that you cannot otherwise configure via the web interface. The Firepower System currently provides only only one advanced variable, the USER_CONF variable.

USER_CONF

USER_CONF provides a general tool that allows you to configure one or more features not otherwise available via the web interface.

Caution

Do not use the advanced variable USER_CONF to configure an intrusion policy feature unless you are instructed to do so in the feature description or by Support. Conflicting or duplicate configurations will halt the system.

When editing USER_CONF, you can type up to 4096 total characters on a single line; the line wraps automatically. You can include any number of valid instructions or lines until you reach the 8192 maximum character length for a variable or a physical limit such as disk space. Use the backslash (\) line continuation character after any complete argument in a command directive.

Resetting USER_CONF empties it.

Variable Reset

You can reset a variable to its default value on the variable set new or edit variables page. The following table summarizes the basic principles of resetting variables.

Table 2. Variable Reset Values
Resetting this variable type...	In this set type...	Resets it to...
default	default	the rule update value
user-defined	default	`any`
default or user-defined	custom	the current default set value (modified or unmodified)

Resetting a variable in a custom set simply resets it to the current value for that variable in the default set.

Conversely, resetting or modifying the value of a variable in the default set always updates the default value of that variable in all custom sets. When the reset icon is grayed out, indicating that you cannot reset the variable, this means that the variable has no customized value in that set. Unless you have customized the value for a variable in a custom set, a change to the variable in the default set updates the value used in any intrusion policy where you have linked the variable set.

Note

It is good practice when you modify a variable in the default set to assess how the change affects any intrusion policy that uses the variable in a linked custom set, especially when you have not customized the variable value in the custom set.

You can hover your pointer over the Reset icon in a variable set to see the reset value. When the customized value and the reset value are the same, this indicates one of the following:

you are in the custom or default set where you added the variable with the value any
you are in the custom set where you added the variable with an explicit value and elected to use the configured value as the default value

Adding Variables to Sets

Adding a variable to a variable set adds it to all other sets. When you add a variable from a custom set, you must choose whether to use the configured value as the customized value in the default set:

If you use the configured value (for example, 192.168.0.0/16), the variable is added to the default set using the configured value as a customized value with a default value of any. Because the current value in the default set determines the default value in other sets, the initial, default value in other custom sets is the configured value (which in the example is 192.168.0.0/16).
If you do not use the configured value, the variable is added to the default set using only the default value any and, consequently, the initial, default value in other custom sets is any.

Example: Adding User-Defined Variables to Default Sets

The following diagram illustrates set interactions when you add the user-defined variable Var1 to the default set with the value 192.168.1.0/24.

You can customize the value of Var1 in any set. In Custom Set 2 where Var1 has not been customized, its value is 192.168.1.0/24. In Custom Set 1 the customized value 192.168.2.0/24 of Var1 overrides the default value. Resetting a user-defined variable in the default set resets its default value to any in all sets.

It is important to note in this example that, if you do not update Var1 in Custom Set 2, further customizing or resetting Var1 in the default set consequently updates the current, default value of Var1 in Custom Set 2, thereby affecting any intrusion policy linked to the variable set.

Although not shown in the example, note that interactions between sets are the same for user-defined variables and default variables except that resetting a default variable in the default set resets it to the value configured by Cisco in the current rule update.

Example: Adding User-Defined Variables to Custom Sets

The next two examples illustrate variable set interactions when you add a user-defined variable to a custom set. When you save the new variable, you are prompted whether to use the configured value as the default value for other sets. In the following example, you elect to use the configured value.

Note that, except for the origin of Var1 from Custom Set 1, this example is identical to the example above where you added Var1 to the default set. Adding the customized value 192.168.1.0/24 for Var1 to Custom Set 1 copies the value to the default set as a customized value with a default value of any. Thereafter, Var1 values and interactions are the same as if you had added Var1 to the default set. As with the previous example, keep in mind that further customizing or resetting Var1 in the default set consequently updates the current, default value of Var1 in Custom Set 2, thereby affecting any intrusion policy linked to the variable set.

In the next example, you add Var1 with the value 192.168.1.0/24 to Custom Set 1 as in the previous example, but you elect not to use the configured value of Var1 as the default value in other sets.

This approach adds Var1 to all sets with a default value of any. After adding Var1, you can customize its value in any set. An advantage of this approach is that, by not initially customizing Var1 in the default set, you decrease your risk of customizing the value in the default set and thus inadvertently changing the current value in a set such as Custom Set 2 where you have not customized Var1.

Nesting Variables

You can nest variables so long as the nesting is not circular. Nested, negated variables are not supported.

Valid Nested Variables

In this example, SMTP_SERVERS, HTTP_SERVERS, and OTHER_SERVERS are valid nested variables.


Variable	Type	Included Networks	Excluded Networks
SMTP_SERVERS	customized default	10.1.1.1	—
HTTP_SERVERS	customized default	10.1.1.2	—
OTHER_SERVERS	user-defined	10.2.2.0/24	—
HOME_NET	customized default	10.1.1.0/24 OTHER_SERVERS	SMTP_SERVERS HTTP_SERVERS

An Invalid Nested Variable

In this example, HOME_NET is an invalid nested variable because the nesting of HOME_NET is circular; that is, the definition of OTHER_SERVERS includes HOME_NET, so you would be nesting HOME_NET in itself.


Variable	Type	Included Networks	Excluded Networks
SMTP_SERVERS	customized default	10.1.1.1	—
HTTP_SERVERS	customized default	10.1.1.2	—
OTHER_SERVERS	user-defined	10.2.2.0/24 HOME_NET	—
HOME_NET	customized default	10.1.1.0/24 OTHER_SERVERS	SMTP_SERVERS HTTP_SERVERS

An Unsupported Nested, Negated Variable

Because nested, negated variables are not supported, you cannot use the variable NONCORE_NET as shown in this example to represent IP addresses that are outside of your protected networks.


Variable	Type	Included Networks	Excluded Networks
HOME_NET	customized default	10.1.0.0/16 10.2.0.0/16 10.3.0.0/16	—
EXTERNAL_NET	customized default	—	HOME_NET
DMZ_NET	user-defined	10.4.0.0/16	—
NOT_DMZ_NET	user-defined	—	DMZ_NET
NONCORE_NET	user-defined	EXTERNAL_NET NOT_DMZ_NET	—

Alternative to an Unsupported Nested, Negated Variable

As an alternative to the example above, you could represent IP addresses that are outside of your protected networks by creating the variable NONCORE_NET as shown in this example.


Variable	Type	Included Networks	Excluded Networks
HOME_NET	customized default	10.1.0.0/16 10.2.0.0/16 10.3.0.0/16	—
DMZ_NET	user-defined	10.4.0.0/16	—
NONCORE_NET	user-defined	—	HOME_NET DMZ_NET

Managing Variable Sets

To use variable sets, you must have the Threat license (for FTD devices) or the Protection license (all other device types).

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1

Choose Objects > Object Management.

Step 2

Choose Variable Set from the list of object types.

Step 3

Manage your variable sets:

Add — If you want to add a custom variable set, click Add Variable Set; see Creating Variable Sets.

Delete — If you want to delete a custom variable set, click Delete ( delete icon

) next to the variable set, then click Yes. You cannot delete the default variable set or variable sets belonging to ancestor domains.

Note

Variables created in a variable set you delete are not deleted or otherwise affected in other sets.

Edit — If you want to edit a variable set, click Edit () next to the variable set you want to modify; see Editing Objects.
Filter — If you want to filter variable sets by name, begin entering a name; as you type, the page refreshes to display matching names. If you want to clear name filtering, click Clear () in the filter field.
Manage Variables — To manage the variables included in variable sets, see Managing Variables.

Creating Variable Sets

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose Variable Set from the list of object types.
Step 3	Click Add Variable Set.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Optionally, enter a Description.
Step 6	Manage the variables in the set; see Managing Variables.
Step 7	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Managing Variables

You must have the Threat license (for FTD devices) or the Protection license (all other device types).

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1

Choose Objects > Object Management.

Step 2

Choose Variable Set from the list of object types.

Step 3

Click Edit ( edit icon ) next to the variable set you want to edit.

If View ( view button ) appears instead, the configuration belongs to an ancestor domain, or you do not have permission to modify the configuration.

Step 4

Manage your variables:

Display — If you want to display the complete value for a variable, hover your pointer over the value in the Value column next to the variable.
Add — If you want to add a variable, click Add; see Adding Variables.
Delete — Click Delete () next to the variable. If you have saved the variable set since adding the variable, click Yes to confirm that you want to delete the variable.
You cannot delete the following:
- default variables
- user-defined variables that are used by intrusion rules or other variables
- variables belonging to ancestor domains
Edit — Click Edit () next to the variable you want to edit; see Editing Variables.

Reset — If you want to reset a modified variable to its default value, click Reset next to a modified variable. If reset is dimmed, one of the following is true:

The current value is already the default value.
The configuration belongs to an ancestor domain.

Tip

Hover your pointer over an active reset to display the default value.

Step 5

Click Save to save the variable set. If the variable set is in use by an access control policy, click Yes to confirm that you want to save your changes.

Because the current value in the default set determines the default value in all other sets, modifying or resetting a variable in the default set changes the current value in other sets where you have not customized the default value.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Adding Variables

You must have the Threat license (for FTD devices) or the Protection license (all other device types).

Procedure

Step 1

In the variable set editor, click Add.

Step 2

Enter a unique variable Name.

Step 3

From the Type drop-down list, choose either Network or Port.

Step 4

Specify values for the variable:

If you want to move items from the list of available networks or ports to the list of included or excluded items, you can choose one or more items and then drag and drop, or click Include or Exclude.

Tip

If addresses or ports in the included and excluded lists for a network or port variable overlap, excluded addresses or ports take precedence.

Enter a single literal value, then click Add. For network variables, you can enter a single IP address or address block. For port variables you can add a single port or port range, separating the upper and lower values with a hyphen (-). Repeat this step as needed to enter multiple literal values.
If you want to remove an item from the included or excluded lists, click Delete () next to the item.

Note

The list of items to include or exclude can be comprised of any combination of literal strings and existing variables, objects, and network object groups in the case of network variables.

Step 5

Click Save to save the variable. If you are adding a new variable from a custom set, you have the following options:

Click Yes to add the variable using the configured value as the customized value in the default set and, consequently, the default value in other custom sets.
Click No to add the variable as the default value of any in the default set and, consequently, in other custom sets.

Step 6

Click Save to save the variable set. Your changes are saved, and any access control policy the variable set is linked to displays an out-of-date status.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Editing Variables

You must have the Threat license (for FTD devices) or the Protection license (all other device types).

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

You can edit both custom and default variables.

You cannot change the Name or Type values in an existing variable.

Procedure

Step 1

In the variable set editor, click Edit ( edit icon ) next to the variable you want to modify.

If View ( view button ) appears instead, the object belongs to an ancestor domain, or you do not have permission to modify the object.

Step 2

Modify the variable:

If you want to move items from the list of available networks or ports to the list of included or excluded items, you can select one or more items and then drag and drop, or click Include or Exclude.

Tip

If addresses or ports in the included and excluded lists for a network or port variable overlap, excluded addresses or ports take precedence.

Enter a single literal value, then click Add. For network variables, you can enter a single IP address or address block. For port variables you can add a single port or port range, separating the upper and lower values with a hyphen (-). Repeat this step as needed to enter multiple literal values.
If you want to remove an item from the included or excluded lists, click Delete () next to the item.

Note

The list of items to include or exclude can be comprised of any combination of literal strings and existing variables, objects, and network object groups in the case of network variables.

Step 3

Click Save to save the variable.

Step 4

Click Save to save the variable set. If the variable set is in use by an access control policy, click Yes to confirm that you want to save your changes. Your changes are saved, and any access control policy the variable set is linked to displays an out-of-date status.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Security Intelligence Lists and Feeds

Security Intelligence functionality requires the Threat license (for FTD devices) or the Protection license (all other device types).

Security Intelligence lists and feeds are collections of IP addresses, domain names, and URLs that you can use to quickly filter traffic that matches an entry on a list or feed.

A list is a static collection that you manage manually.
A feed is a dynamic collection that updates on an interval over HTTP or HTTPS.

Security Intelligence lists/feeds are grouped into:

DNS (Domain names )
Network (IP addresses)
URLs

System-Provided Feeds

Cisco provides the following feeds as Security Intelligence objects:

Security Intelligence feeds updated regularly with the latest threat intelligence from Talos:
- Cisco-DNS-and-URL-Intelligence-Feed (under DNS Lists and Feeds)
- Cisco-Intelligence-Feed (for IP addresses, under Network Lists and Feeds)
You cannot delete the system-provided feeds, but you can change the frequency of (or disable) their updates.

Predefined Lists: Global Block Lists and Global Do Not Block Lists

The system ships with predefined global Block lists and Do Not Block lists for domains (DNS), IP addresses (Networks), and URLs.

These lists are empty until you populate them. To build these lists, see Global and Domain Security Intelligence Lists.

By default, access control and DNS policies use these lists as part of Security Intelligence.

Custom Feeds

You can use third-party feeds, or use a custom internal feed to easily maintain an enterprise-wide Block list in a large deployment with multiple Firepower Management Center appliances.

See Custom Security Intelligence Feeds.

Custom Lists

Custom lists can augment and fine-tune feeds and the Global lists.

See Custom Security Intelligence Lists.

Where Security Intelligence Lists and Feeds Are Used

IP address and address blocks—Use Block and Do Not Block lists in access control policies, as part of Security Intelligence.
Domain Names—Use Block and Do Not Block lists in DNS policies, as part of Security Intelligence.
URLs—Use Block and Do Not Block lists in access control policies, as part of Security Intelligence. You can also use URL lists in access control rules, whose analysis and traffic handling phases occur after Security Intelligence.

How to Modify Security Intelligence Objects

To add or delete entries on a Block list, Do Not Block list, feed, or sinkhole object:


Object Type	Edit Capabilities	Requires Redeploy After Edit?
Custom Block and Do Not Block lists	Upload new and replacement lists using the object manager.	Yes
Default (but custom-populated) Block lists and Do Not Block lists: Global, descendant, and domain-specific	Add entries using the context menu or delete entries using the object manager.	No
System-provided Intelligence Feeds	Disable or change update frequency using the object manager.	No
Custom feeds	Fully modify using the object manager.	No
Sinkhole	Fully modify using the object manager.	Yes

Global and Domain Security Intelligence Lists

Firepower Management Center ships with empty Global Block and Do-Not-Block lists to which you can instantly add URLs, domains, and IP addresses from events on your network at any time. These lists allow you to use Security Intelligence to always block particular connections, or to exempt particular connections from blocking by Security Intelligence, allowing them to be evaluated by other threat detection processes that you have configured.

For example, if you notice a set of routable IP addresses in intrusion events associated with exploit attempts, you can immediately block those IP addresses. Although it may take a few minutes for your changes to propagate, you do not have to redeploy.

By default, Access control and DNS policies use these Global lists, which apply to all security zones. You can opt not to use these lists on a per-policy basis.

Note

These options apply to Security Intelligence only. Security Intelligence cannot block traffic that has already been fastpathed. Similarly, adding an item to a Security Intelligence Do Not Block list does not automatically trust or fastpath matching traffic. For more information, see About Security Intelligence.

In a multidomain deployment, you can choose the Firepower System domains where you want to enforce blocking, or exempting from Security Intelligence blocking, by adding items to Domain lists as well as the Global lists; see Security Intelligence Lists and Multitenancy.

Security Intelligence Lists and Multitenancy

In a multidomain deployment, the Global domain owns the Global Block lists and Do Not Block lists. Only Global administrators can add to or remove items from the Global lists. So that subdomain users can add networks, domain names, and URLs to Block and Do Not Block lists, multitenancy adds:

Domain lists—Block or Do Not Block lists whose contents apply to a particular subdomain only. The Global lists are Domain lists for the Global domain.
Descendant Domain lists—Block or Do Not Block lists that aggregate the Domain lists of the current domain’s descendants.

Domain Lists

In addition to being able to access (but not edit) the Global lists, each subdomain has its own named lists, the contents of which apply only to that subdomain. For example, a subdomain named Company A owns:

Domain Block list - Company A and Domain Do Not Block list - Company A
Domain Block list for DNS - Company A, Domain Do Not Block list for DNS - Company A
Domain Block list for URL - Company A, Domain Do Not Block list for URL - Company A

Any administrator at or above the current domain can populate these lists. You can use the context menu to add an item to the Block or Do Not Block list in the current and all descendant domains. However, only an administrator in the associated domain can remove an item from a Domain list.

For example, a Global administrator could choose to add the same IP address to the Block list in the Global domain and Company A’s domain, but not add it to the Block list in Company B’s domain. This action would add the same IP address to:

Global Block list (where it can be removed only by Global administrators)
Domain Block list - Company A (where it can be removed only by Company A administrators)

The system builds a separate network map for each leaf domain. In a multidomain deployment, using literal IP addresses to constrain this configuration can have unexpected results.

Descendant Domain Lists

A Descendant Domain list is a Do Not Block list or Block list that aggregates the Domain lists of the current domain’s descendants. Leaf domains do not have Descendant Domain lists.

Descendant Domain lists are useful because a higher-level domain administrator can enforce general Security Intelligence settings, while still allowing subdomain users to add items to a Block or Do Not Block list in their own deployment.

For example, the Global domain has the following Descendant Domain lists:

Descendant Block lists - Global, Descendant Do Not Block lists - Global
Descendant Block lists for DNS - Global, Descendant Do Not Block lists for DNS - Global
Descendant Block lists for URL - Global, Descendant Do Not Block lists for URL - Global

Note

Descendant Domain lists do not appear in the object manager because they are symbolic aggregations, not hand-populated lists. They appear where you can use them: in access control and DNS policies.

Add Entries to Global Security Intelligence Lists

When reviewing events and dashboards, you can instantly block future traffic involving IP addresses, domains, and URLs that appear in those events by adding them to a predefined Block list.

Similarly, if Security Intelligence is blocking traffic that you want evaluated by threat detection processes subsequent to Security Intelligence blocking, you can add IP addresses, domains, and URLs from events to a predefined Do Not Block list.

Traffic is evaluated against entries on these lists during the Security Intelligence phase of threat detection.

For more information about these lists, see Global and Domain Security Intelligence Lists.

Before you begin

Because adding an entry to a Security Intelligence list affects access control, you must have one of the following user roles:

Administrator
A combination of roles: Network Admin or Access Admin, plus Security Analyst and Security Approver
A custom role with both Modify Access Control Policy and Deploy Configuration to Devices permissions

If appropriate, verify that these lists are used in the policies in which you expect them to be used.

Procedure

Step 1

Navigate to an event that includes an IP address, domain, or URL that you want to always block using Security Intelligence, or exempt from Security Intelligence blocking.

Step 2

Right-click the IP address, domain, or URL and choose the appropriate option:


Target Item	Context Menu Option	Affected Global Lists
An IP address	Blacklist Now Whitelist Now	Global Block List Global Whitelist
A URL	Blacklist HTTP/S Connections to URL Now Whitelist HTTP/S Connections to URL Now	Global Block List for URL Global Whitelist for URL
An entire domain	Blacklist HTTP/S Connections to Domain Now Whitelist HTTP/S Connections to Domain Now	Global Block List for URL Global Whitelist for URL
DNS requests for an entire domain	Blacklist DNS Requests to Domain Now Whitelist DNS Requests to Domain Now	Global Block List for DNS Global Whitelist for DNS

What to do next

You do NOT need to redeploy for these changes to take effect.

If you want to delete an item from a list, see Delete Entries from Global Security Intelligence Lists.

Delete Entries from Global Security Intelligence Lists

Note

In multi-domain deployments, the names of these lists may not be "Global." For more information, see Security Intelligence Lists and Multitenancy.
To add entries to these lists, see Add Entries to Global Security Intelligence Lists.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Click Security Intelligence.
Step 3	Click the appropriate option: Network Lists and Feeds (for IP addresses) DNS Lists and Feeds (for domain names) URL Lists and Feeds
Step 4	Click the pencil beside the Global Block or Global Do-Not-Block list.
Step 5	Click the trash button beside the entry to delete.

List and Feed Updates for Security Intelligence

List and feed updates replace the existing list or feed file with the contents of the new file. Contents of existing and new files are not merged.

If the system downloads a corrupt feed or a feed with no recognizable entries, the system continues using the old feed data (unless it is the first download). However, if the system can recognize even one entry in the feed, it uses the entries it can recognize.

By default, each feed updates the Management Center every two hours; you can modify this frequency. Any updates the Management Center receives are passed immediately to managed devices. In addition, managed devices poll the FMC every 30 minutes for changes. You cannot modify this frequency.

In a multidomain deployment, the system-provided feeds belong to the Global domain and can be modified only by an administrator in that domain. You can modify the update frequency for custom feeds belonging to your domain.

To modify feed update intervals, see Changing the Update Frequency for Security Intelligence Feeds.

Changing the Update Frequency for Security Intelligence Feeds

You can specify the intervals at which the Firepower Management Center updates Security Intelligence Feeds.

For details about feed updates, see List and Feed Updates for Security Intelligence.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the Security Intelligence node, then choose the feed type whose frequency you want to change. The system-provided URL feed is combined with the domain feed under DNS Lists and Feeds.
Step 3	Next to the feed you want to update, click Edit (). If View () appears instead, the object belongs to an ancestor domain, or you do not have permission to modify the object.
Step 4	Edit the Update Frequency.
Step 5	Click Save.

Custom Security Intelligence Lists and Feeds

Custom Lists and Feeds: Requirements

List and Feed Formatting

Each list or feed must be a simple text file no larger than 500MB. List files must have the .txt extension. Include one entry or comment per line: one IP address, one URL, one domain name.

Tip

The number of entries you can include is limited by the maximum size of the file. For example, a URL list with no comments and an average URL length of 100 characters (including Punycode or percent Unicode representations and newlines) can contain more than 5.24 million entries.

In a DNS list entry, you can specify an asterisk (*) wildcard character for a domain label. All labels match the wildcard. For example, an entry of www.example.* matches both www.example.com and www.example.co.

If you add comment lines within the source file, they must start with the pound (#) character. If you upload a source file with comments, the system removes your comments during upload. Source files you download contain all your entries without your comments.

Feed Requirements

When you configure a feed, you specify its location using a URL; the URL cannot be Punycode-encoded.

If you use an MD5 checksum, the checksum must be stored in a simple text file with only the checksum. Comments are not supported.

URL Lists and Feeds: URL Syntax and Matching Criteria

Security Intelligence URL lists and feeds, including custom lists and feeds and entries in the global Block list and Do Not Block list, can include the following, which have the matching behavior as described:

Hostnames

For example, www.example.com.
URLs

example.com matches example.com and all subdomains, including www.example.com, eu.example.com, example.com/abc, and www.example.com/def -- but NOT example.co.uk or examplexyz.com or example.com.malicious-site.com

You can also include an entire URL path, such as https://www.cisco.com/c/en/us/products/security/firewalls/index.html
A slash at the end of a URL to specify an exact match

example.com/ matches ONLY example.com; it does NOT match www.example.com or any other URL.
A wildcard (*) to represent any domain in a URL

An asterisk can represent a complete domain string separated by dots, but not a partial domain string, and not any part of the URL following the first slash.

Valid examples:
- *.example.com
- www.*.com
- example.*
  
  (This will match example.com and example.org and example.de, for example, but NOT example.co.uk)
- *.example.*
- example.*/
Invalid examples:
- example*.com
- example.com/*
IP addresses (IPv4)

For IPv6 addresses, or to use ranges or CIDR notation, use the Security Intelligence Network object.

You can include one or more wildcards representing an octet, for example 10.10.10.* or 10.10.*.*.

Custom Security Intelligence Feeds

Custom or third-party Security Intelligence feeds allow you to augment the system-provided Intelligence Feeds with other regularly-updated reputable Block lists and Do Not Block lists on the Internet. You can also set up an internal feed, which is useful if you want to update multiple Firepower Management Center appliances in your deployment using one source list.

Note

You cannot add address blocks to Block or Do Not Block lists using a /0 netmask in a Security Intelligence feed. If you want to monitor or block all traffic targeted by a policy, use an access control rule with the Monitor or Block rule action, respectively, and a default value of any for the Source Networks and Destination Networks.

You also can configure the system to use an MD5 checksum to determine whether to download an updated feed. If the checksum has not changed since the last time the system downloaded the feed, the system does not need to re-download it. You may want to use MD5 checksums for internal feeds, especially if they are large.

Note

The system does not perform peer SSL certificate verification when downloading custom feeds, nor does the system support the use of certificate bundles or self-signed certificates to verify the remote peer.

If you want strict control over when the system updates a feed from the Internet, you can disable automatic updates for that feed. However, automatic updates ensure the most up-to-date, relevant data.

Manually updating Security Intelligence feeds updates all feeds, including the Intelligence Feeds.

See complete requirements at Custom Lists and Feeds: Requirements.

Creating Security Intelligence Feeds

You must have the Threat license (for FTD devices) or the Protection license (all other device types).

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the Security Intelligence node, then choose a feed type you want to add.
Step 3	Click the option appropriate to the feed type you chose above: Add Network Lists and Feeds (for IP addresses) Add DNS Lists and Feeds Add URL Lists and Feeds
Step 4	Enter a Name for the feed. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Choose Feed from the Type drop-down list.
Step 6	Enter a Feed URL.
Step 7	(Optional) Enter an MD5 URL. This is used to determine whether the feed contents have changed since the last update, so the system does not download unchanged feeds.
Step 8	Choose an Update Frequency.
Step 9	Click Save. Unless you disabled feed updates, the system attempts to download and verify the feed.

Manually Updating Security Intelligence Feeds

You must have the Threat license (for FTD devices) or the Protection license (all other device types).

Before you begin

At least one device must already be added to the management center.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the Security Intelligence node, then choose a feed type.
Step 3	Click Update Feeds, then confirm.
Step 4	Click OK.

After the Firepower Management Center downloads and verifies the feed updates, it communicates any changes to its managed devices. Your deployment begins filtering traffic using the updated feeds.

Custom Security Intelligence Lists

Security Intelligence lists are simple static lists of IP addresses and address blocks, URLs, or domain names that you manually upload to the system. Custom lists are useful if you want to augment and fine-tune feeds or one of the global lists, for a single Firepower Management Center’s managed devices.

For example, if a reputable feed improperly blocks your access to vital resources but is overall useful to your organization, you can create a custom Do Not Block list that contains only the improperly classified IP addresses, rather than removing the IP address feed object from the access control policy’s Block list.

Note

You cannot add address blocks to a Block or Do Not Block list using a /0 netmask in a Security Intelligence list. If you want to monitor or block all traffic targeted by a policy, use an access control rule with the Monitor or Block rule action, respectively, and a default value of any for the Source Networks and Destination Networks.

Regarding list entry formatting, note the following:

Netmasks for address blocks can be integers from 0 to 32 or 0 to 128, for IPv4 and IPv6, respectively.
Unicode in domain names must be encoded in Punycode format, and are case insensitive.
Characters in domain names are case-insensitive.
Unicode in URLs should be encoded in percent-encoding format.
Characters in URL subdirectories are case-sensitive.
List entries that start with the pound sign (#) are treated as comments.
See additional formatting requirements at Custom Lists and Feeds: Requirements.

Regarding matching list entries, note the following:

The system matches sub-level domains if a higher-level domain exists in a URL or DNS list. For example, if you add example.com to a DNS list, the system matches both www.example.com and test.example.com.
The system does not perform DNS lookups (forward or reverse) on DNS or URL list entries. For example, if you add http://192.168.0.2 to a URL list, and it resolves to http://www.example.com, the system only matches http://192.168.0.2, not http://www.example.com.

Uploading New Security Intelligence Lists to the Firepower Management Center

To modify a Security Intelligence list, you must make your changes to the source file and upload a new copy. You cannot modify the file’s contents using the web interface. If you do not have access to the source file, download a copy from the system.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the Security Intelligence node, then choose a list type.
Step 3	Click the option appropriate to the list you chose above: Add Network Lists and Feeds (for IP addresses) Add DNS Lists and Feeds Add URL Lists and Feeds
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	From the Type drop-down list, choose List.
Step 6	Click Browse to browse to the list `.txt` file, then click Upload.
Step 7	Click Save.

What to do next

If an active policy references your object, deploy configuration changes, see Deploy Configuration Changes

Updating Security Intelligence Lists

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the Security Intelligence node, then choose a list type.
Step 3	Next to the list you want to update, click Edit (). If View () appears instead, the configuration belongs to an ancestor domain, or you do not have permission to modify the configuration.
Step 4	If you need a copy of the list to edit, click Download, then follow your browser’s prompts to save the list as a text file.
Step 5	Make changes to the list as necessary.
Step 6	On the Security Intelligence pop-up window, click Browse to browse to the modified list, then click Upload.
Step 7	Click Save.

What to do next

If an active policy references your object, deploy configuration changes, see Deploy Configuration Changes.

Sinkhole Objects

A sinkhole object represents either a DNS server that gives non-routeable addresses for all domain names within the sinkhole, or an IP address that does not resolve to a server. You can reference the sinkhole object within a DNS policy rule to redirect matching traffic to the sinkhole. You must assign the object both an IPv4 address and an IPv6 address.

Creating Sinkhole Objects

You must have the Threat license (for FTD devices) or the Protection license (all other device types).

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose Sinkhole from the list of object types.
Step 3	Click Add Sinkhole.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Enter the IPv4 Address and IPv6 Address of your sinkhole.
Step 6	You have the following options: If you want to redirect traffic to a sinkhole server, choose Log Connections to Sinkhole. If you want to redirect traffic to a non-resolving IP address, choose Block and Log Connections to Sinkhole.
Step 7	If you want to assign an Indication of Compromise (IoC) type to your sinkhole, choose one from the Type drop-down.
Step 8	Click Save.

File Lists

If you use AMP for Networks, and the AMP cloud incorrectly identifies a file’s disposition, you can add the file to a file list to better detect the file in the future. These files are specified using SHA-256 hash values. Each file list can contain up to 10000 unique SHA-256 values.

There are two predefined categories of file lists:

Clean List: If you add a file to this list, the system treats it as if the AMP cloud assigned a clean disposition.
Custom Detection List: If you add a file to this list, the system treats it as if the AMP cloud assigned a malware disposition.

In a multidomain deployment, a clean list and custom detection list is present for each domain. In lower-level domains, you can view but not modify ancestor's lists.

Because you manually specify the blocking behavior for the files included in these lists, the system does not query the AMP cloud for these files’ dispositions. You must configure a rule in the file policy with either a Malware Cloud Lookup or Block Malware action and a matching file type to calculate a file’s SHA value.

Caution

Do not include malware on the clean list. The clean list overrides both the AMP cloud and the custom detection list.

Source Files for File Lists

You can add multiple SHA-256 values to a file list by uploading a comma-separated value (CSV) source file containing a list of SHA-256 values and descriptions. The Firepower Management Center validates the contents and populates the file list with valid SHA-256 values.

The source file must be a simple text file with a .csv file name extension. Any header must start with a pound sign (#); it is treated as a comment and not uploaded. Each entry should contain a single SHA-256 value followed by a description and end with either the LF or CR+LF Newline character. The system ignores any additional information in the entry.

Note the following:

Deleting a source file from the file list also removes all associated SHA-256 hashes from the file list.
You cannot upload multiple files to a file list if the successful source file upload results in the file list containing more than 10000 distinct SHA-256 values.
The system truncates descriptions exceeding 256 characters to the first 256 characters on upload. If the description contains commas, you must use an escape character (\,). If no description is included, the source file name is used instead.
All non-duplicate SHA-256 values are added to the file list. If a file list contains a SHA-256 value, and you upload a source file containing that value, the newly uploaded value does not modify the existing SHA-256 value. When viewing captured files, file events, or malware events related to the SHA-256 value, any threat name or description is derived from the individual SHA-256 value.
The system does not upload invalid SHA-256 values in a source file.
If multiple uploaded source files contain an entry for the same SHA-256 value, the system uses the most recent value.
If a source file contains multiple entries for the same SHA-256 value, the system uses the last one.
You cannot directly edit a source file within the object manager. To make changes, you must first modify your source file directly, delete the copy on the system, then upload the modified source file.
The number of entries associated with a source file refers to the number of distinct SHA-256 values. If you delete a source file from a file list, the total number of SHA-256 entries the file list contains decreases by the number of valid entries in the source file.

Adding Individual SHA-256 Values to File Lists

You must have the Malware license for this procedure.

You can submit a file’s SHA-256 value to add it to a file list. You cannot add duplicate SHA-256 values.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Before you begin

Right-click a file or malware event from the event view, choose Show Full Text in the context menu, and copy the full SHA-256 value for pasting into the file list.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose File List from the list of object types.
Step 3	Click Edit () next to the clean list or custom detection list where you want to add a file. If View () appears instead, the object belongs to an ancestor domain, or you do not have permission to modify the object.
Step 4	Choose `Enter SHA Value` from the Add by drop-down list.
Step 5	Enter a description of the source file in the Description field.
Step 6	Enter or paste the file’s entire value in the SHA-256 field. The system does not support matching partial values.
Step 7	Click Add.
Step 8	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Note

After configuration changes are deployed, the system no longer queries the AMP cloud for files on the list.

Uploading Individual Files to File Lists

You must have the Malware license for this procedure.

If you have a copy of the file you want to add to a file list, you can upload the file to the Firepower Management Center for analysis; the system calculates the file’s SHA-256 value and adds the file to the list. The system does not enforce a limit on the size of files for SHA-256 calculation.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose File List from the list of object types.
Step 3	Click Edit () next to the clean list or custom detection list where you want to add a file. If View () appears instead, the object belongs to an ancestor domain, or you do not have permission to modify the object.
Step 4	From the Add by drop-down list, choose Calculate SHA.
Step 5	Optionally, enter a description of the file in the Description field. If you do not enter a description, the file name is used for the description on upload.
Step 6	Click Browse, and choose a file to upload.
Step 7	Click Calculate and Add SHA.
Step 8	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Note

After you deploy configuration changes, the system no longer queries the AMP cloud for files on the list.

Uploading Source Files to File Lists

You must have the Malware license for this procedure.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Click File List.
Step 3	Click Edit () next to the file list where you want to add values from a source file. If View () appears instead, the object belongs to an ancestor domain, or you do not have permission to modify the object.
Step 4	In the Add by drop-down list, choose `List of SHAs`.
Step 5	Optionally, enter a description of the source file in the Description field. If you do not enter a description, the system uses the file name.
Step 6	Click Browse to browse to the source file, then click Upload and Add List.
Step 7	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Note

After you deploy the policies, the system no longer queries the AMP cloud for files on the list.

Editing SHA-256 Values in File Lists

You must have the Malware license for this procedure.

You can edit or delete individual SHA-256 values on a file list. Note that you cannot directly edit a source file within the object manager. To make changes, you must first modify your source file directly, delete the copy on the system, then upload the modified source file.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Click File List.
Step 3	Click Edit () next to the clean list or custom detection list where you want to modify a file. If View () appears instead, the object belongs to an ancestor domain, or you do not have permission to modify the object.
Step 4	You can: Click Edit () next to the SHA-256 value you want to change, and modify the SHA-256 or Description values as desired. Click Delete () next to the SHA-256 value you want to delete.
Step 5	Click Save to update the file entry in the list.
Step 6	Click Save to save the file list.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Note

After configuration changes are deployed, the system no longer queries the AMP cloud for files on the list.

Downloading Source Files from File Lists

You must have the Malware license for this procedure.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose File List from the list of object types.
Step 3	Click Edit () next to the clean list or custom detection list where you want to download a source file. If View () appears instead, the object belongs to an ancestor domain, or you do not have permission to modify the object.
Step 4	Next to the source file you want to download, click View ().
Step 5	Click Download SHA List and follow the prompts to save the source file.
Step 6	Click Close.

Cipher Suite Lists

A cipher suite list is an object comprised of several cipher suites. Each predefined cipher suite value represents a cipher suite used to negotiate an SSL- or TLS-encrypted session. You can use cipher suites and cipher suite lists in SSL rules to control encrypted traffic based on whether the client and server negotiated the SSL session using that cipher suite. If you add a cipher suite list to an SSL rule, SSL sessions negotiated with any of the cipher suites in the list match the rule.

Note

Although you can use cipher suites in the web interface in the same places as cipher suite lists, you cannot add, modify, or delete cipher suites.

Creating Cipher Suite Lists

You can use these objects with any device type except NGIPSv.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Choose Cipher Suite List from the list of object types.
Step 3	Click Add Cipher Suites.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Choose one or more cipher suites from the Available Ciphers list.
Step 6	Click Add.
Step 7	Optionally, click Delete () next to any cipher suites in the Selected Ciphers list that you want to remove.
Step 8	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Distinguished Name Objects

Each distinguished name object represents the distinguished name for a public key certificate’s subject or issuer. You can use distinguished name objects and groups in TLS/SSL rules to control encrypted traffic based on whether the client and server negotiated the TLS/SSL session using a server certificate with the distinguished name as subject or issuer.

(A distinguished name group is a named collection of existing distinguished name objects.)

The distinguished name can consist of country code, common name, organization, and organizational unit, but typically consists of a common name only. For example, the common name in the certificate for https://www.cisco.com is cisco.com. The certificate can contain multiple Subject Alternative Names (SANs) you can use as DNs in a rule condition. For detailed information about SANs, see RFC 528, section 4.2.1.6.

The format of a distginguished name object that references a common name is CN=name. If you add a DN rule condition without CN=, the system prepends CN= before saving the object.

The Firepower System uses Server Name Indication (SNI) to match the DN in the TLS/SSL rule whenever possible.

You can also add a distinguished name with one of each of the attributes listed in the following table, separated by commas.

Table 3. Distinguished name attributes
Attribute	Description	Allowed Values
C	Country Code	two alphabetic characters
CN	Common Name	up to 64 alphanumeric, backslash (/), hyphen (-), quotation ("), or asterisk (*) characters, or spaces
O	Organization	up to 64 alphanumeric, backslash (/), hyphen (-), quotation ("), or asterisk (*) characters, or spaces
OU	Organizational Unit	up to 64 alphanumeric, backslash (/), hyphen (-), quotation ("), or asterisk (*) characters, or spaces

Important notes about DN rule conditions

The first time the system detects an encrypted session to a new server, DN data is not available for ClientHello processing, which might result in an undecrypted first session.
You cannot configure a distinguished name condition if you also choose the Decrypt - Known Key action. Because that action requires you to choose a server certificate to decrypt traffic, the certificate already matches the traffic.

Wildcard examples

You can define one or more asterisks (*) as wildcards in an attribute. In a common name attribute, you can define one or more asterisks per domain name label. wildcards match only in that label, but you can define multiple labels with wildcards. See the following table for examples.

Table 4. Common Name attribute wildcard examples
Attribute	Matches	Does Not Match
CN=*ample.com	example.com	mail.example.com example.text.com ampleexam.com
CN=exam*.com	example.com	mail.example.com example.text.com ampleexam.com
CN=xamp.com	example.com	mail.example.com example.text.com ampleexam.com
CN=*.example.com	mail.example.com	www.myhost.example.com example.com example.text.com ampleexam.com

Note

The DN object CN=amp.cisco.com would not match a CN like CN=auth.amp.cisco.com, which is why we recommend wildcards in these cases.

Creating Distinguished Name Objects

You can use these objects with any device type except NGIPSv.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the Distinguished Name node, and choose Individual Objects.
Step 3	Click Add Distinguished Name.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	In the DN field, enter a value for the distinguished name or common name. You have the following options: If you add a distinguished name, you can include one of each attribute listed in Distinguished Name Objects separated by commas. If you add a common name, you can include multiple labels and wild cards.
Step 6	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

PKI Objects

PKI Objects for SSL Application

PKI objects represent the public key certificates and paired private keys required to support your deployment. Internal and trusted CA objects consist of certificate authority (CA) certificates; internal CA objects also contain the private key paired with the certificate. Internal and external certificate objects consist of server certificates; internal certificate objects also contain the private key paired with the certificate.

If you use trusted certificate authority objects and internal certificate objects to configure a connection to ISE, you can use ISE as an identity source.

If you use internal certificate objects to configure captive portal, the system can authenticate the identity of your captive portal device when connecting to users' web browsers.

If you use trusted certificate authority objects to configure realms, you can configure secure connections to LDAP or AD servers.

If you use PKI objects in SSL rules, you can match traffic encrypted with:

the certificate in an external certificate object
a certificate either signed by the CA in a trusted CA object, or within the CA’s chain of trust

If you use PKI objects in SSL rules, you can decrypt:

outgoing traffic by re-signing the server certificate with an internal CA object
incoming traffic using the known private key in an internal certificate object

You can manually input certificate and key information, upload a file containing that information, or in some cases, generate a new CA certificate and private key.

When you view a list of PKI objects in the object manager, the system displays the certificate’s Subject distinguished name as the object value. Hover your pointer over the value to view the full certificate Subject distinguished name. To view other certificate details, edit the PKI object.

Note

The Firepower Management Center and managed devices encrypt all private keys stored in internal CA objects and internal certificate objects with a randomly generated key before saving them. If you upload private keys that are password protected, the appliance decrypts the key using the user-supplied password, then reencrypts it with the randomly generated key before saving it.

Internal Certificate Authority Objects

Each internal certificate authority (CA) object you configure represents the CA public key certificate of a CA your organization controls. The object consists of the object name, CA certificate, and paired private key. You can use internal CA objects and groups in SSL rules to decrypt outgoing encrypted traffic by re-signing the server certificate with the internal CA.

Note

If you reference an internal CA object in a Decrypt - Resign SSL rule and the rule matches an encrypted session, the user’s browser may warn that the certificate is not trusted while negotiating the SSL handshake. To avoid this, add the internal CA object certificate to either the client or domain list of trusted root certificates.

You can create an internal CA object in the following ways:

import an existing RSA-based or elliptic curve-based CA certificate and private key
generate a new self-signed RSA-based CA certificate and private key
generate an unsigned RSA-based CA certificate and private key. You must submit a certificate signing request (CSR) to another CA to sign the certificate before using the internal CA object.

After you create an internal CA object containing a signed certificate, you can download the CA certificate and private key. The system encrypts downloaded certificates and private keys with a user-provided password.

Whether system-generated or user-created, you can modify the internal CA object name, but cannot modify other object properties.

You cannot delete an internal CA object that is in use. Additionally, after you edit an internal CA object used in an SSL policy, the associated access control policy goes out-of-date. You must re-deploy the access control policy for your changes to take effect.

CA Certificate and Private Key Import

You can configure an internal CA object by importing an X.509 v3 CA certificate and private key. You can upload files encoded in one of the following supported formats:

Distinguished Encoding Rules (DER)
Privacy-enhanced Electronic Mail (PEM)

If the private key file is password-protected, you can supply the decryption password. If the certificate and key are encoded in the PEM format, you can also copy and paste the information.

You can upload only files that contain proper certificate or key information, and that are paired with each other. The system validates the pair before saving the object.

Note

If you configure a rule with the Decrypt - Resign action, the rule matches traffic based on the referenced internal CA certificate’s encryption algorithm type, in addition to any configured rule conditions. You must upload an elliptic curve-based CA certificate to decrypt outgoing traffic encrypted with an elliptic curve-based algorithm, for example.

Importing a CA Certificate and Private Key

You can use these objects with any device type except NGIPSv.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the PKI node, and choose Internal CAs.
Step 3	Click Import CA.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Above the Certificate Data field, click Browse to upload a DER or PEM-encoded X.509 v3 CA certificate file.
Step 6	Above the Key field, click Browse to upload a DER or PEM-encoded paired private key file.
Step 7	If the uploaded file is password-protected, check the Encrypted, and the password is: check box, and enter the password.
Step 8	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Generating a New CA Certificate and Private Key

You can use these objects with any device type except NGIPSv.

You can configure an internal CA object by providing identification information to generate a self-signed RSA-based CA certificate and private key.

The generated CA certificate is valid for ten years. The Valid From date is a week before generation.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the PKI node, and choose Internal CAs.
Step 3	Click Generate CA.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Enter the identification attributes.
Step 6	Click Generate self-signed CA.

New Signed Certificates

You can configure an internal CA object by obtaining a signed certificate from a CA. This involves two steps:

Provide identification information to configure the internal CA object. This generates an unsigned certificate and paired private key, and creates a certificate signing request (CSR) to a CA you specify.
After the CA issues the signed certificate, upload it to the internal CA object, replacing the unsigned certificate.

You can only reference an internal CA object in an SSL rule if it contains a signed certificate.

Creating an Unsigned CA Certificate and CSR

You can use these objects with any device type except NGIPSv.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the PKI node, and choose Internal CAs.
Step 3	Click Generate CA.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Enter the identification attributes.
Step 6	Click Generate CSR.
Step 7	Copy the CSR to submit to a CA.
Step 8	Click OK.

What to do next

You must upload a signed certificate issued by a CA as described in Uploading a Signed Certificate Issued in Response to a CSR

Uploading a Signed Certificate Issued in Response to a CSR

You can use these objects with any device type except NGIPSv.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Once uploaded, the signed certificate can be referenced in SSL rules.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the PKI node, and choose Internal CAs.
Step 3	Click Edit () next to the CA object containing the unsigned certificate awaiting the CSR.
Step 4	Click Install Certificate.
Step 5	Click Browse to upload a DER or PEM-encoded X.509 v3 CA certificate file.
Step 6	If the uploaded file is password protected, check the Encrypted, and the password is: check box, and enter the password.
Step 7	Click Save to upload a signed certificate to the CA object.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

CA Certificate and Private Key Downloads

You can back up or transfer a CA certificate and paired private key by downloading a file containing the certificate and key information from an internal CA object.

Caution

Always store downloaded key information in a secure location.

The system encrypts the private key stored in an internal CA object with a randomly generated key before saving it to disk. If you download a certificate and private key from an internal CA object, the system first decrypts the information before creating a file containing the certificate and private key information. You must then provide a password the system uses to encrypt the downloaded file.

Caution

Private keys downloaded as part of a system backup are decrypted, then stored in the unencrypted backup file.

Downloading a CA Certificate and Private Key

You can use these objects with any device type except NGIPSv.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

You can download CA certificates for both the current domain and ancestor domains.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the PKI node, and choose Internal CAs.
Step 3	Next to the internal CA object whose certificate and private key you want to download, click Edit (). In a multidomain deployment, click View () to download the certificate and private key for an object in an ancestor domain.
Step 4	Click Download.
Step 5	Enter an encryption password in the Password and Confirm Password fields.
Step 6	Click OK.

Trusted Certificate Authority Objects

Each trusted certificate authority (CA) object you configure represents a CA public key certificate belonging to a trusted CA. The object consists of the object name and CA public key certificate. You can use external CA objects and groups in:

your SSL policy to control traffic encrypted with a certificate signed either by the trusted CA, or any CA within the chain of trust.
your realm configurations to establish secure connections to LDAP or AD servers.
your ISE connection. Select trusted certificate authority objects for the pxGrid Server CA and MNT Server CA fields.

After you create the trusted CA object, you can modify the name and add certificate revocation lists (CRL), but cannot modify other object properties. There is no limit on the number of CRLs you can add to an object. If you want to modify a CRL you have uploaded to an object, you must delete the object and recreate it.

Note

Adding a CRL to an object has no effect when the object is used in your ISE integration configuration.

You cannot delete a trusted CA object that is in use. Additionally, after you edit a trusted CA object that is in use, the associated access control policy goes out-of-date. You must re-deploy the access control policy for your changes to take effect.

Trusted CA Object

You can configure an external CA object by uploading an X.509 v3 CA certificate. You can upload a file encoded in one of the following supported formats:

Distinguished Encoding Rules (DER)
Privacy-enhanced Electronic Mail (PEM)

If the file is password-protected, you must supply the decryption password. If the certificate is encoded in the PEM format, you can also copy and paste the information.

You can upload a CA certificate only if the file contains proper certificate information; the system validates the certificate before saving the object.

Adding a Trusted CA Object

You can use these objects with any device type except NGIPSv.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the PKI node, and choose Trusted CAs.
Step 3	Click Add Trusted CAs.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Click Browse to upload a DER or PEM-encoded X.509 v3 CA certificate file.
Step 6	If the file is password-protected, check the Encrypted, and the password is: check box, and enter the password.
Step 7	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Certificate Revocation Lists in Trusted CA Objects

You can upload CRLs to a trusted CA object. If you reference that trusted CA object in an SSL policy, you can control encrypted traffic based on whether the CA that issued the session encryption certificate subsequently revoked the certificate. You can upload files encoded in one of the following supported formats:

Distinguished Encoding Rules (DER)
Privacy-enhanced Electronic Mail (PEM)

After you add the CRL, you can view the list of revoked certificates. If you want to modify a CRL you have uploaded to an object, you must delete the object and recreate it.

You can upload only files that contain a proper CRL. There is no limit to the number of CRLs you can add to a trusted CA object. However, you must save the object each time you upload a CRL, before adding another CRL.

Note

Adding a CRL to an object has no effect when the object is used in your ISE integration configuration.

Adding a Certificate Revocation List to a Trusted CA Object

You can use these objects with any device type except NGIPSv.

In a multidomain deployment, the system displays objects created in the current domain, which you can edit. It also displays objects created in ancestor domains, which in most cases you cannot edit. To view and edit objects in a descendant domain, switch to that domain.

Note

Adding a CRL to an object has no effect when the object is used in your ISE integration configuration.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the PKI node, and choose Trusted CAs.
Step 3	Click Edit () next to a trusted CA object. If View () appears instead, the configuration belongs to an ancestor domain, or you do not have permission to modify the configuration.
Step 4	Click Add CRL to upload a DER or PEM-encoded CRL file.
Step 5	Click OK.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

External Certificate Objects

Each external certificate object you configure represents a server public key certificate that does not belong to your organization. The object consists of the object name and certificate. You can use external certificate objects and groups in SSL rules to control traffic encrypted with the server certificate. For example, you can upload a self-signed server certificate that you trust, but cannot verify with a trusted CA certificate.

You can configure an external certificate object by uploading an X.509 v3 server certificate. You can upload a file in one of the following supported formats:

Distinguished Encoding Rules (DER)
Privacy-enhanced Electronic Mail (PEM)

You can upload only files that contains proper server certificate information; the system validates the file before saving the object. If the certificate is encoded in the PEM format, you can also copy and paste the information.

Adding External Certificate Objects

You can use these objects with any device type except NGIPSv.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the PKI node, and choose External Certs.
Step 3	Click Add External Cert.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Above the Certificate Data field, click Browse to upload a DER or PEM-encoded X.509 v3 server certificate file.
Step 6	Click Save.

What to do next

If an active policy references your object, deploy configuration changes; see Deploy Configuration Changes.

Internal Certificate Objects

Each internal certificate object you configure represents a server public key certificate belonging to your organization. The object consists of the object name, public key certificate, and paired private key. You can use internal certificate objects and groups in:

your SSL rules to decrypt traffic incoming to one of your organization’s servers using the known private key.
your ISE connection. Select an internal certificate object for the MC Server Certificate field.
your captive portal configuration to authenticate the identity of your captive portal device when connecting to users' web browsers. Select an internal certificate object for the Server Certificate field.

You can configure an internal certificate object by uploading an X.509 v3 RSA-based or elliptic curve-based server certificate and paired private key. You can upload a file in one of the following supported formats:

Distinguished Encoding Rules (DER)
Privacy-enhanced Electronic Mail (PEM)

If the file is password-protected, you must supply the decryption password. If the certificate and key are encoded in the PEM format, you can also copy and paste the information.

You can upload only files that contain proper certificate or key information, and that are paired with each other. The system validates the pair before saving the object.

After you create the internal certificate object, you can modify the name, but cannot modify other object properties.

You cannot delete an internal certificate object that is in use. Additionally, after you edit an internal certificate object that is in use, the associated access control policy goes out-of-date. You must re-deploy the access control policy for your changes to take effect.

Adding Internal Certificate Objects

You can use these objects with any device type except NGIPSv.

Procedure

Step 1	Choose Objects > Object Management.
Step 2	Expand the PKI node, and choose Internal Certs.
Step 3	Click Add Internal Cert.
Step 4	Enter a Name. In a multidomain deployment, object names must be unique within the domain hierarchy. The system may identify a conflict with the name of an object you cannot view in your current domain.
Step 5	Above the Certificate Data field, click Browse to upload a DER or PEM-encoded X.509 v3 server certificate file.
Step 6	Above the Key field, or click Browse to upload a DER or PEM-encoded paired private key file.
Step 7	If the uploaded private key file is password-protected, check the Encrypted, and the password is: check box, and enter the password.
Step 8	Click Save.

SLA Monitor Objects

Each Internet Protocol Service Level Agreement (SLA) monitor defines a connectivity policy to a monitored address and tracks the availability of a route to the address. The route is periodically checked for availability by sending ICMP echo requests and waiting for the response. If the requests time out, the route is removed from the routing table and replaced with a backup route. SLA monitoring jobs start immediately after deployment and continue to run unless you remove the SLA monitor from the device configuration (that is, they do not age out). The Internet Protocol Service Level Agreement (SLA) Monitor Object is used in the Route Tracking field of an IPv4 Static Route Policy. IPv6 routes do not have the option to use SLA monitor via route tracking.

You can use these objects with Firepower Threat Defense devices.

Procedure

Step 1

Select Objects > Object Management and choose SLA Monitor from the table of contents.

Step 2

Click Add SLA Monitor.

Step 3

Enter a name for the object in the Name field.

Step 4

(Optional) Enter a description for the object in the Description field.

Step 5

Enter the frequency of ICMP echo request transmissions, in seconds, in the Frequency field. Valid values range from 1 to 604800 seconds (7 days). The default is 60 seconds.

Note

The frequency cannot be less than the timeout value; you must convert frequency to milliseconds to compare the values.

Step 6

Enter the ID number of the SLA operation in the SLA Monitor ID field. Values range from 1 to 2147483647. You can create a maximum of 2000 SLA operations on a device. Each ID number must be unique to the policy and the device configuration.

Step 7

Enter the amount of time that must pass after an ICMP echo request before a rising threshold is declared, in milliseconds, in the Threshold field. Valid values range from 0 to 2147483647 milliseconds. The default is 5000 milliseconds. The threshold value is used only to indicate events that exceed the defined value. You can use these events to evaluate the proper timeout value. It is not a direct indicator of the reachability of the monitored address.

Note

The threshold value should not exceed the timeout value.

Step 8

Enter the amount of time that the SLA operation waits for a response to the ICMP echo requests, in milliseconds, in the Timeout field. Values range from 0 to 604800000 milliseconds (7 days). The default is 5000 milliseconds. If a response is not received from the monitored address within the amount of time defined in this field, the static route is removed from the routing table and replaced by the backup route.

Note

The timeout value cannot exceed the frequency value (adjust the frequency value to milliseconds to compare the numbers).

Step 9

Enter the size of the ICMP request packet payload, in bytes, in the Data Size field. Values range from 0 to 16384 bytes. The default is 28 bytes, which creates a total ICMP packet of 64 bytes. Do not set this value higher than the maximum allowed by the protocol or the Path Maximum Transmission Unit (PMTU). For purposes of reachability, you might need to increase the default data size to detect PMTU changes between the source and the target. A low PMTU can affect session performance and, if detected, might indicate that the secondary path should be used.

Step 10

Enter a value for type of service (ToS) defined in the IP header of the ICMP request packet in the ToS field. Values range from 0 to 255. The default is 0. This field contains information such as delay, precedence, reliability, and so on. It can be used by other devices on the network for policy routing and features such as committed access rate.

Step 11

Enter the number of packets that are sent in the Number of Packets field. Values range from 1 to 100. The default is 1 packet.

Note

Increase the default number of packets if you are concerned that packet loss might falsely cause the Firepower Threat Defense device to believe that the monitored address cannot be reached.

Step 12

Enter the IP address that is being monitored for availability by the SLA operation, in the Monitored Address field.

Step 13

The Available Zones list displays both zones and interface groups. In the Zones/Interfaces list, add the zones or interface groups that contain the interfaces through which the device communicates with the management station. To specify a single interface, you need to create a zone or the interface groups for the interface; see Creating Security Zone Objects. The host will be configured on a device only if the device includes the selected interfaces or zones.

Step 14

Click Save.

Prefix Lists

You can create prefix list objects for IPv4 and IPv6 to use when you are configuring route maps, policy maps, OSPF Filtering, or BGP Neighbor Filtering.

Configure IPv6 Prefix List

Use the Configure IPv6 Prefix list page to create, copy and edit prefix list objects. You can create prefix list objects to use when you are configuring route maps, policy maps, OSPF Filtering, or BGP Neighbor Filtering.

You can use this object with Firepower Threat Defense devices.

Procedure

Step 1	Select Objects > Object Management and choose Prefix Lists > IPv6 Prefix List from the table of contents.
Step 2	Click Add Prefix List.
Step 3	Enter a name for the prefix list object in the Name field on the New Prefix List Object window.
Step 4	Click Add on theNew Prefix List Object window.
Step 5	Select the appropriate action, Allow or Block from the Action drop-down list, to indicate the redistribution access.
Step 6	Enter a unique number that indicates the position a new prefix list entry will have in the list of prefix list entries already configured for this object, in the Sequence No. field. If left blank, the sequence number will default to five more than the largest sequence number currently in use.
Step 7	Specify the IPv6 address in the IP address/mask length format in the IP address field. The mask length must be a valid value between 1-128.
Step 8	Enter the minimum prefix length in the Minimum Prefix Length field. The value must be greater than the mask length and less than or equal to the Maximum Prefix Length, if specified.
Step 9	Enter the maximum prefix length in the Maximum Prefix Length field. The value must be greater than or equal to the Minimum Prefix Length, if present, or greater than the mask length if the Minimum Prefix Length is not specified.
Step 10	Click Add.
Step 11	If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides.
Step 12	Click Save.

Configure IPv4 Prefix List

Use the Configure IPv4 Prefix list page to create, copy and edit prefix list objects. You can create prefix list objects to use when you are configuring route maps, policy maps, OSPF Filtering, or BGP Neighbor Filtering.

You can use this object with Firepower Threat Defense devices.

Procedure

Step 1	Select Objects > Object Management and choose Prefix Lists > IPv4 Prefix List from the table of contents.
Step 2	Click Add Prefix List.
Step 3	Enter a name for the prefix list object in the Name field on the New Prefix List Object window.
Step 4	Click Add.
Step 5	Select the appropriate action, Allow or Block from the Action drop-down list, to indicate the redistribution access.
Step 6	Enter a unique number that indicates the position a new prefix list entry will have in the list of prefix list entries already configured for this object, in the Sequence No. field. If left blank, the sequence number will default to five more than the largest sequence number currently in use.
Step 7	Specify the IPv4 address in the IP address/mask length format in the IP address field. The mask length must be a valid value between 1- 32.
Step 8	Enter the minimum prefix length in the Minimum Prefix Length field. The value must be greater than the mask length and less than or equal to the Maximum Prefix Length, if specified.
Step 9	Enter the maximum prefix length in the Maximum Prefix Length field. The value must be greater than or equal to the Minimum Prefix Length, if present, or greater than the mask length if the Minimum Prefix Length is not specified.
Step 10	Click Add.
Step 11	If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides.
Step 12	Click Save.

Route Maps

Route maps are used when redistributing routes into any routing process. They are also used when generating a default route into a routing process. A route map defines which of the routes from the specified routing protocol are allowed to be redistributed into the target routing process. Configure a route map, to create a new route map entry for a Route Map object or to edit an existing one.

You can use this object with Firepower Threat Defense devices.

Before you begin

A Route Map may use one or mores of these objects; it is not mandatory to add all these objects. Create and use any of these objects as required, to configure your route map.

Add ACLs.
Add Prefix Lists.
Add AS Path.
Add Community Lists.
Add Policy Lists.

Procedure

Step 1

Select Objects > Object Management and choose Route Map from the table of contents.

Step 2

Click Add Route Map.

Step 3

Click Add on theNew Route Map Object window.

Step 4

In the Sequence No. field, enter a number, between 0 and 65535, that indicates the position a new route map entry will have in the list of route maps entries already configured for this route map object.

Note

We recommend that you number clauses in intervals of at least 10 to reserve numbering space in case you need to insert clauses in the future.

Step 5

Select the appropriate action, Allow or Block from the Redistribution drop-down list, to indicate the redistribution access.

Step 6

Click the Match Clauses tab to match (routes/traffic) based on the following criteria, which you select in the table of contents:

Security Zones — Match traffic based on the (ingress/egress) interfaces. You can select zones and add them, or type in interface names and add them.
IPv4 — Match IPv4 (routes/traffic) based on the following criteria; select the tab to define the criteria.
1. Click the Address tab to match routes based on the route address. For IPv4 addresses, choose whether to use an Access list or Prefix list for matching from the drop-down list and then enter or select the ACL objects or Prefix list objects you want to use for matching.
2. Click the Next Hop tab to match routes based on the next hop address of a route. For IPv4 addresses, choose whether to use an access list or Prefix list for matching from the drop-down list and then enter or select the ACL objects or Prefix list objects you want to use for matching.
3. Click the Route Source tab to match routes based on the advertising source address of the route. For IPv4 addresses, choose whether to use an access list or Prefix list for matching from the drop-down list and then enter or select the ACL objects or Prefix list objects you want to use for matching.
IPv6 — Match IPv6 (routes/traffic) based on the route address, next-hop address or advertising source address of route.
BGP — Match BGP (routes/traffic) based on the following criteria; select the tab to define the criteria.
1. Click the AS Path tab to enable matching the BGP autonomous system path access list with the specified path access list. If you specify more than one path access list, then the route can match either path access list.
2. Click the Community List tab to enable matching the BGP community with the specified community. If you specify more than one community, then the route can match either community. Any route that does not match at least one Match community will not be advertised for outbound route maps.
3. Click the Policy List tab to configure a route map to evaluate and process a BGP policy. When multiple policy lists perform matching within a route map entry, all policy lists match on the incoming attribute only.
Others — Match routes or traffic based on the following criteria.
1. Enter the metric values to use for matching in the Metric Route Value field, to enable matching the metric of a route. You can enter multiple values separated by commas. This setting allows you to match any routes that have a specified metric. The metric values can range from 0 to 4294967295.
2. Enter the tag values to use for matching in the Tag Values field. You can enter multiple values separated by commas. This setting allows you to match any routes that have a specified security group tag. The tag values can range from 0 to 4294967295.
3. Check the appropriate Route Type option to enable matching of the route type. Valid route types are External1, External2, Internal, Local, NSSA-External1, and NSSA-External2. You can choose more than one route type from the list.

Step 7

Click the Set Clauses tab to set routes/traffic based on the following criteria, which you select in the table of contents:

Metric Values — Set either Bandwidth, all of the values or none of the values.
1. Enter a metric value or bandwidth in Kbits per second in the Bandwidth field. Valid values are an integer value in the range from 0 to 4294967295.
2. Select to specify the type of metric for the destination routing protocol, from the Metric Type drop-down list. Valid values are : internal, type-1, or type-2.
BGP Clauses — Set BGP routes based on the following criteria; select the tab to define the criteria.
1. Click the AS Path tab to modify an autonomous system path for BGP routes.
  1. Enter an AS path number in the Prepend AS Path field to prepend an arbitrary autonomous system path string to BGP routes. Usually the local AS number is prepended multiple times, increasing the autonomous system path length. If you specify more than one AS path number then the route can prepend either AS number.
  2. Enter an AS path number in the Prepend Last AS to AS Path field to prepend the AS path with the last AS number. Enter a value for the AS number from 1 to 10.
  3. Check the Convert route tag into AS path check box to convert the tag of a route into an autonomous system path.
2. Click the Community List tab to set the community attributes.
  1. Click the None radio button, to remove the community attribute from the prefixes that pass the route map.
  2. Click the Specific Community radio button, to enter a community number, if applicable. Valid values are from 1 to 4294967295.
  3. Check the Add to existing communities check box, to add the community to the already existing communities.
  4. Select the Internet, No-Advertise, or No-Export check-boxes to use one of the well-known communities.
3. Click the Others tab to set additional attributes.
  1. Check the Set Automatic Tag check-box to automatically compute the tag value.
  2. Enter a preference value for the autonomous system path in the Set Local Preference field. Enter a value between 0 and 4294967295.
  3. Enter a BGP weight for the routing table in the Set Weight field. Enter a value between 0 and 65535.
  4. Select to specify the BGP origin code. Valid values are Local IGP Local IGP and Incomplete.
  5. In the IPv4 Settings section, specify a next hop IPv4 address of the next hop to which packets are output. It need not be an adjacent router. If you specify more than one IPv4 address then the packets can output at either IP address.
    
    Select to specify an IPv4 prefix list in the Prefix List drop-down list.
  6. In the IPv6 Settings section, specify a next hop IPv6 address of the next hop to which packets are output. It need not be an adjacent router. If you specify more than one IPv6 address then the packets can output at either IP address.
    
    Select to specify an IPv6 prefix in the Prefix List drop-down list.

Step 8

Click Add.

Step 9

If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides.

Step 10

Click Save.

Access List

An access list object, also known as an access control list (ACL), selects the traffic to which a service will apply. You use these objects when configuring particular features, such as route maps, for Firepower Threat Defense devices. Traffic identified as allowed by the ACL is provided the service, whereas “blocked” traffic is excluded from the service. Excluding traffic from a service does not necessarily mean that it is dropped altogether.

You can configure the following types of ACL:

Extended—Identifies traffic based on source and destination address and ports. Supports IPv4 and IPv6 addresses, which you can mix in a given rule.
Standard—Identifies traffic based on destination address only. Supports IPv4 only.

An ACL is composed of one or more access control entry (ACE), or rule. The order of ACEs is important. When the ACL is evaluated to determine if a packet matches an “allowed” ACE, the packet is tested against each ACE in the order in which the entries are listed. After a match is found, no more ACEs are checked. For example, if you want to “allow” 10.100.10.1, but “block” the rest of 10.100.10.0/24, the allow entry must come before the block entry. In general, place more specific rules at the top of an ACL.

Packets that do not match an “allow” entry are considered to be blocked.

The following topics explain how to configure ACL objects.

Configure Extended ACL Objects

Use extended ACL objects when you want to match traffic based on source and destination addresses, protocol and port, or if the traffic is IPv6.

Procedure

Step 1

Select Objects > Object Management and choose Access Control Lists > Extended from the table of contents.

Step 2

Do one of the following:

Click Add Extended ACL to create a new object.
Click Edit () to edit an existing object.

Step 3

In the Extended ACL Object dialog box, enter a name for the object (no spaces allowed), and configure the access control entries:

Do one of the following:
- Click Add to create a new entry.
- Click Edit () to edit an existing entry.
The right-click menu also includes options to cut, copy, and paste entries, or to delete them.

Select the Action, whether to Allow (match) or Block (not match) the traffic criteria.

Note

The Logging, Log Level, and Log Interval options are used for access rules only (ACLs attached to interfaces or applied globally). Because ACL objects are not used for access rules, leave these values at their defaults.

Configure the source and destination addresses on the Network tab using any of the following techniques:
- Select the desired network objects or groups from the Available list and click Add to Source or Add to Destination. You can create new objects by clicking the + button above the list. You can mix IPv4 and IPv6 addresses.
- Type an address in the edit box below the source or destination list and click Add. You can specify a single host address (such as 10.100.10.5 or 2001:DB8::0DB8:800:200C:417A), or a subnet (in 10.100.10.0/24 or 10.100.10.0 255.255.255.0 format, or for IPv6, 2001:DB8:0:CD30::/60).

Click the Port tab and configure the service using any of the following techniques.

Select the desired port objects from the Available list and click Add to Source or Add to Destination. You can create new objects by clicking the + button above the list. The object can specify TCP/UDP ports, ICMP/ICMPv6 message types, or other protocols (including “any”). However, the source port, which you typically would leave empty, accepts TCP/UDP only. You cannot select port groups.
Type or select a port or protocol in the edit box below the source or destination list and click Add.

Note

To get an entry that applies to all IP traffic, select a destination port object that specifies “all” protocols.

Click Add to add the entry to the object.
If necessary, click and drag the entry to move it up or down in the rule order to the desired location.

Repeat the process to create or edit additional entries in the object.

Step 4

If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides.

Step 5

Click Save.

Configure Standard ACL Objects

Use standard ACL objects when you want to match traffic based on destination IPv4 address only. Otherwise, use extended ACLs.

Procedure

Step 1	Select Objects > Object Management and choose Access Control Lists > Standard from the table of contents.
Step 2	Do one of the following: Click Add Standard ACL to create a new object. Click Edit () to edit an existing object.
Step 3	In the Standard ACL Object dialog box, enter a name for the object (no spaces allowed), and configure the access control entries: Do one of the following: Click Add to create a new entry. Click Edit () to edit an existing entry. The right-click menu also includes options to cut, copy, and paste entries, or to delete them. For each access control entry, configure the following properties: Action—Whether to Allow (match) or Block (not match) the traffic criteria. Network—Add the IPv4 network objects or groups that identify the destination of the traffic. Click Add to add the entry to the object. If necessary, click and drag the entry to move it up or down in the rule order to the desired location. Repeat the process to create or edit additional entries in the object.
Step 4	If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides.
Step 5	Click Save.

AS Path Objects

An AS Path is a mandatory attribute to set up BGP. It is a sequence of AS numbers through which a network can be accessed. An AS-PATH is a sequence of intermediate AS numbers between source and destination routers that form a directed route for packets to travel. Neighboring autonomous systems (ASes ) use BGP to exchange and update messages about how to reach different AS prefixes. After each router makes a new local decision on the best route to a destination, it will send that route, or path information, along with the accompanying distance metrics and path attributes, to each of its peers. As this information travels through the network, each router along the path prepends its unique AS number to a list of ASes in the BGP message. This list is the route's AS-PATH. An AS-PATH along with an AS prefix, provides a specific handle for a one-way transit route through the network. Use the Configure AS Path page to create, copy and edit autonomous system (AS) path policy objects. You can create AS path objects to use when you are configuring route maps, policy maps, or BGP Neighbor Filtering. An AS path filter allows you to filter the routing update message by using regular expressions.

You can use this object with Firepower Threat Defense devices.

Procedure

Step 1	Select Objects > Object Management and choose AS Path from the table of contents.
Step 2	Click Add AS Path.
Step 3	Enter a name for the AS Path object in the Name field. Valid values are between 1 and 500.
Step 4	Click Add on the New AS Path Object window. Select the Allow or Block options from the Action drop-down list to indicate redistribution access. Specify the regular expression that defines the AS path filter in the Regular Expression field. Click Add.
Step 5	If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides.
Step 6	Click Save.

Community Lists

A Community is an optional transitive BGP attribute. A community is a group of destinations that share some common attribute. It is used for route tagging. The BGP community attribute is a numerical value that can be assigned to a specific prefix and advertised to other neighbors. Communities can be used to mark a set of prefixes that share a common attribute. Upstream providers can use these markers to apply a common routing policy such as filtering or assigning a specific local preference or modifying other attributes. Use the Configure Community Lists page to create, copy and edit community list policy objects. You can create community list objects to use when you are configuring route maps or policy maps. You can use community lists to create groups of communities to use in a match clause of a route map. The community list is an ordered list of matching statements. Destinations are matched against the rules until a match is found.

You can use this object with Firepower Threat Defense devices.

Procedure

Step 1

Select Objects > Object Management and choose Community List from the table of contents.

Step 2

Click Add Community List.

Step 3

In the Name field, specify a name for the community list object.

Step 4

Click Add on the New Community List Object window.

Step 5

Select the Standard radio button to indicate the community rule type.

Standard community lists are used to specify well-known communities and community numbers.

Note

You cannot have entries using Standard and entries using Expanded community rule types in the same Community List object.

Select the Allow or Block options from the Action drop-down list to indicate redistribution access.
In the Communities field, specify a community number. Valid values can be from 1 to 4294967295 or from 0:1 to 65534:65535.
Select the appropriate Route Type.
- Internet — Select to specify the Internet well-known community. Routes with this community are advertised to all peers (internal and external).
- No Advertise — Select to specify the no-advertise well-known community. Routes with this community are not advertised to any peer (internal or external).
- No Export — Select to specify the no-export well-known community. Routes with this community are advertised to only peers in the same autonomous system or to only other sub-autonomous systems within a confederation. These routes are not advertised to external peers.

Step 6

Select the Expanded radio button to indicate the community rule type.

Expanded community lists are used to filter communities using a regular expression. Regular expressions are used to specify patterns to match COMMUNITIES attributes.

Select the Allow or Block options from the Action drop-down list to indicate redistribution access.
Specify the regular expression in the Expressions field.

Step 7

Click Add.

Step 8

If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides.

Step 9

Click Save.

Policy Lists

Use the Configure Policy List page to create, copy, and edit policy list policy objects. You can create policy list objects to use when you are configuring route maps. When a policy list is referenced within a route map, all of the match statements within the policy list are evaluated and processed. Two or more policy lists can be configured with a route map. A policy list can also coexist with any other preexisting match and set statements that are configured within the same route map but outside of the policy list. When multiple policy lists perform matching within a route map entry, all policy lists match on the incoming attribute only.

You can use this object with Firepower Threat Defense devices.

Procedure

Step 1	Select Objects > Object Management and choose Policy List from the table of contents.
Step 2	Click Add Policy List.
Step 3	Enter a name for the policy list object in the Name field. Object names are not case-sensitive.
Step 4	Select whether to allow or block access for matching conditions from the Action drop-down list.
Step 5	Click the Interface tab to distribute routes that have their next hop out of one of the interfaces specified. In the Zones/Interfaces list, add the zones that contain the interfaces through which the device communicates with the management station. For interfaces not in a zone, you can type the interface name into the field below the Selected Zone/Interface list and click Add. The host will be configured on a device only if the device includes the selected interfaces or zones.
Step 6	Click the Address tab to redistribute any routes that have a destination address that is permitted by a standard access list or prefix list. Choose whether to use an Access List or Prefix List for matching and then enter or select the Standard Access List Objects or Prefix list objects you want to use for matching.
Step 7	Click the Next Hop tab to redistribute any routes that have a next hop router address passed by one of the access lists or prefix lists specified. Choose whether to use an Access List or Prefix List for matching and then enter or select the Standard Access List Objects or Prefix list objects you want to use for matching.
Step 8	Click the Route Source tab to redistribute routes that have been advertised by routers and access servers at the address specified by the access lists or prefix list. Choose whether to use an Access List or Prefix List for matching and then enter or select the Standard Access List Objects or Prefix list objects you want to use for matching.
Step 9	Click the AS Path tab to match a BGP autonomous system path. If you specify more than one AS path, then the route can match either AS path.
Step 10	Click the Community Rule tab to enable matching the BGP community with the specified community. If you specify more than one community, then the route can match either community. To enable matching the BGP community exactly with the specified community, check the Match the specified community exactly check box.
Step 11	Click the Metric & tag tab to match the metric and security group tag of a route. Enter the metric values to use for matching in the Metric field. You can enter multiple values separated by commas. This setting allows you to match any routes that have a specified metric. The metric values can range from 0 to 4294967295. Enter the tag values to use for matching in the Tag field. You can enter multiple values separated by commas. This setting allows you to match any routes that have a specified security group tag. The tag values can range from 0 to 4294967295.
Step 12	If you want to allow overrides for this object, check the Allow Overrides check box; see Allowing Object Overrides.
Step 13	Click Save.

Bias-Free Language

Results

Chapter: Reusable Objects

Reusable Objects

Introduction to Reusable Objects

Object Types

Objects and Multitenancy

The Object Manager

Editing Objects

Procedure

What to do next

Viewing Objects and Their Usage

Procedure

Filtering Objects or Object Groups

Procedure

Object Groups

Grouping Reusable Objects

Procedure

What to do next

Object Overrides

Managing Object Overrides

Procedure

Allowing Object Overrides

Procedure

What to do next

Adding Object Overrides

Before you begin

Procedure

Example:

What to do next

Editing Object Overrides

Procedure

What to do next

Network Objects

Creating Network Objects

Procedure

What to do next

Port Objects

Creating Port Objects

Procedure

What to do next

Application Filters

VLAN Tag Objects

Creating VLAN Tag Objects

Procedure

What to do next

URL Objects

Creating URL Objects

Procedure

What to do next

Geolocation Objects

Creating Geolocation Objects

Procedure

What to do next

Security Zones

Model-Specific Notes and Warnings

Zones and Multitenancy

Creating Security Zone Objects

Before you begin

Procedure

What to do next

Variable Sets

Variable Sets in Intrusion Policies

Variables

Predefined Default Variables

Network Variables

Port Variables

Advanced Variables

USER_CONF

Variable Reset

Adding Variables to Sets

Example: Adding User-Defined Variables to Default Sets

Example: Adding User-Defined Variables to Custom Sets

Nesting Variables

Valid Nested Variables

An Invalid Nested Variable

An Unsupported Nested, Negated Variable

Alternative to an Unsupported Nested, Negated Variable

Managing Variable Sets