The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
To configure mobility sticky anchoring, use the mobility anchor sticky command. To disable the sticky anchoring, use the no form of the command.
To configure guest anchoring, use the mobility anchor ip-address command.
To delete the guest anchor, use the no form of the command.
To configure the device as an auto-anchor, use the mobility anchor command.
mobility anchor { ip-address | sticky }
no mobility anchor { ip-address | sticky }
sticky |
|
||
ip-address |
Configures the IP address for the guest anchor switch to this WLAN. |
Sticky configuration is enabled by default.
WLAN Configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE Cisco IOS XE 3.3SE |
This command was introduced. |
The wlan_id or guest_lan_id must exist and be disabled.
Auto-anchor mobility is enabled for the WLAN or wired guest LAN when you configure the first mobility anchor.
Deleting the last anchor disables the auto-anchor mobility feature and resumes normal mobility for new associations.
Mobility uses the following ports, that are allowed through the firewall:
Switch(config-wlan)# mobility anchor sticky
Switch(config-wlan)# mobility anchor 209.165.200.224
Switch(config-wlan)# mobility anchor
To configure the interswitch mobility manager, use the wireless mobility command.
wireless mobility { dscp value }
dscp value |
Configures the Mobility interswitch DSCP value. |
The default DSCP value is 48.
Global Configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE Cisco IOS XE 3.3SE |
This command was introduced. |
This example shoes how to configure mobility interswitch DSCP with an value of 20:
Switch(config)# wireless mobility dscp 20
To configure mobility peer groups, use the wireless mobility controller peer-group command, to remove the configuration, use the no form of this command.
wireless mobility controller peer-group peer-group member IP ip-addressmode centralized
peer group |
Name of the peer group. |
member IP |
Adds a peer group member. |
ip-address |
IP address of the peer group member to be added. |
mode centralized |
Configures the management mode of the peer group member as centrally managed. |
The centralized mode is off.
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.7.0 E |
This command was introduced. |
Switch enable Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wireless mobility controller peer-group peer1 member ip 10.0.0.1 mode centralized
To configure the mobility group parameter and keep alive its ping parameters, use the wireless mobility group keepalive command. To remove a mobility group parameter, use the no form of the command.
wireless mobility group keepalive { count number | interval interval }
no wireless mobility group keepalive { count numbe r | interval interval }
count number |
Number of times that a ping request is sent to a mobility group member before the member is considered unreachable. The range is from 3 to 20. The default is 3. |
interval interval |
Interval of time between each ping request sent to a mobility group member. The range is from 1 to 30 seconds. The default value is 10 seconds. |
3 seconds for count and 10 seconds for interval.
Global Configuration.
Release | Modification |
---|---|
Cisco IOS XE 3.3SE Cisco IOS XE 3.3SE |
This command was introduced. |
The default values for interval is ten seconds and the default for retries is set to three.
This example shows how to specify the amount of time between each ping request sent to a mobility group member to 10 seconds:
Switch(config)# wireless mobility group keepalive count 10
To add or delete users from mobility group member list, use the wireless mobility group member ip command. To remove a member from the mobility group, use the no form of the command.
wireless mobility group member ip ip-address [ public-ip public-ip-address ] [ group group-name ]
no wireless mobility group member ip ip-address
ip-address |
The IP address of the member controller. |
||
public-ip public-ip-address |
|
||
group group-name |
|
None.
Global Configuration.
Release | Modification |
---|---|
Cisco IOS XE 3.3SE Cisco IOS XE 3.3SE |
This command was introduced. |
The mobility group is used when there is more than one Mobility Controller (MC) in a given deployment. The mobility group can be assigned with a name or it can use the default group name. The mobility group members need to be configured on all the members of the group to roam within the group.
This example shows how to add a member in a mobility group:
Switch(config)# mobility group member ip 10.104.171.101 group TestDocGroup
To configure hte mobility domain name, use the wireless mobility group name command. To remove the mobility domain name, use the no form of the command.
![]() Note | If you are configuring the mobility group in a network where network address translation (NAT) is enabled, enter the IP address that is sent to the controller from the NAT device rather than the controller’s management interface IP address. Otherwise, mobility will fail among controllers in the mobility group. |
wireless mobility group name domain-name
no wireless mobility group name
domain-name |
Creates a mobility group by entering this command. The domain name can be up to 31 case-sensitive characters. |
Default.
Global Configuration.
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to configure a mobility domain name lab1:
Switch(config)# mobility group domain lab1
This command is used to load-balance the mobile clients on a mobility anchor (MA) from a switch peer group (SPG) that is least loaded and is chosen to act as the point of presence for the mobile client.
To configure the mobility load-balance status, use the wireless mobility load-balance command.
To disable the mobility load-balance, use the no wirelessmobility load-balanceform of the command.
To configure the client load on the switch where mobility load-balance is turned on, use the no wirelessmobility load-balance threshold form of the command.
wireless mobility load-balance [ threshold threshold ]
[ no ] wireless mobility load-balance [threshold]
[ no ] wireless mobility load-balance
threshold threshold |
Configures the threshold for the number of clients that can be anchored locally. |
Load balance enabled and set at a value of 1000.
Global Configuration.
Release | Modification |
---|---|
Cisco IOS XE 3.3SE Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to configure the mobility load-balance status with a threshold set at 150.
Switch(config)# wireless mobility load-balance threshold 150
To view the wireless mobility summary, use the show wireless mobility command.
show wireless mobility { load-balance summary agent mobility-agent-ip client summary | ap-list ip-address ip-address| controller client summary| dtls connections| statistics summary}
load-balance summary |
Shows the mobility load-balance properties. |
agent mobility-agent-ip client summary |
Shows the active clients on a mobility agent. |
ap-list ip-address ip-address |
Shows the list of Cisco APs known to the mobility group. |
controller client summary |
Shows the active clients in the subdomain. |
dtls connections |
Shows the DTLS server status. |
statistics |
Shows the statistics for the Mobility manager. |
summary |
Shows the summary of the mobility manager. |
None
Global Configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to display a summary of the mobility manager:
Switch (config)# show wireless mobility ap-list
AP name AP radio MAC Controller IP Learnt from
------------------------------------------------------------------------------------------------------
TSIM_AP-101 0000.2000.6600 9.9.9.2 Self
TSIM_AP-102 0000.2000.6700 9.9.9.2 Self
TSIM_AP-103 0000.2000.6800 9.9.9.2 Self
TSIM_AP-400 0000.2001.9100 9.9.9.2 Self
TSIM_AP-402 0000.2001.9300 9.9.9.2 Self
TSIM_AP-403 0000.2001.9400 9.9.9.2 Self
TSIM_AP-406 0000.2001.9700 9.9.9.2 Self
TSIM_AP-407 0000.2001.9800 9.9.9.2 Self
TSIM_AP-409 0000.2001.9a00 9.9.9.2 Self
To clear wireless statistics, use the clear wireless mobility statistics command.
clear wireless mobility statistics
None
Privileged EXEC
Release | Modification |
---|---|
Cisco IOS XE 3.3SE Cisco IOS XE 3.3SE |
This command was introduced. |
You can clear all the information by using the clear wireless mobility statistics command.
This example shows how to clear wireless mobility statistics:
Switch (config)# clear wireless mobility statistics