The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
To configure a WLAN interface or an interface group, use the client vlan command. To disable the WLAN interface, use the no form of this command.
client vlan interface-id-name-or-group-name
no client vlan
interface-id-name-or-group-name |
Interface ID, name, or VLAN group name. The interface ID can also be in digits too. |
The default interface is configured.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable a client VLAN on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# client vlan client-vlan1 Switch(config-wlan)# end
This example shows how to disable a client VLAN on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no client vlan Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To enable debugging of the Ethernet management port, use the debug fastethernet command in EXEC mode. To disable debugging, use the no form of this command.
debug fastethernet { af | events | packets }
no debug fastethernet { af | events | packets }
af |
Displays Ethernet management port software-address-filter debug messages. |
events |
Displays Ethernet management port event debug messages. |
packets |
Displays Ethernet management port packet debug messages. |
Debugging is disabled.
User EXEC
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The undebug fastethernet { af | events | packets} command is the same as the no debug fastethernet{af| events | packets} command.
When you enable debugging on a switch stack, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number EXEC command. Then enter the debug command at the command-line prompt of the stack member. You also can use the remote command stack-member-number LINE EXEC command on the stack master switch to enable debugging on a member switch without first starting a session.
Command |
Description |
---|---|
show debugging |
Displays information about the types of debugging that are enabled. |
To enable debugging of the power controller and Power over Ethernet (PoE) system, use the debug ilpower command in privileged EXEC mode. To disable debugging, use the no form of this command.
debug ilpower { cdp | controller | event | ha | ipc | police | port | powerman | registries | scp | sense }
no debug ilpower { cdp | controller | event | ha | ipc | police | port | powerman | registries | scp | sense }
cdp |
Displays PoE Cisco Discovery Protocol (CDP) debug messages. |
controller |
Displays PoE controller debug messages. |
event |
Displays PoE event debug messages. |
ha |
Displays PoE high-availability messages. |
ipc |
Displays PoE Inter-Process Communication (IPC) debug messages. |
police |
Displays PoE police debug messages. |
port |
Displays PoE port manager debug messages. |
powerman |
Displays PoE power management debug messages. |
registries |
Displays PoE registries debug messages. |
scp |
Displays PoE SCP debug messages. |
sense |
Displays PoE sense debug messages. |
Debugging is disabled.
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This command is supported only on PoE-capable switches.
When you enable debugging on a switch stack, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number EXEC command. Then enter the debug command at the command-line prompt of the stack member. You also can use the remote command stack-member-number LINE EXEC command on the stack master switch to enable debugging on a member switch without first starting a session.
To enable debugging of interface-related activities, use the debug interface command in privileged EXEC mode. To disable debugging, use the no form of this command.
debug interface { interface-id | counters { exceptions | protocol memory } | null interface-number | port-channel port-channel-number | states| vlan vlan-id }
no debug interface { interface-id | counters { exceptions | protocol memory } | null interface-number | port-channel port-channel-number | states| vlan vlan-id }
interface-id |
ID of the physical interface. Displays debug messages for the specified physical port, identified by type switch number/module number/port, for example, gigabitethernet 1/0/2. |
null interface-number |
Displays debug messages for null interfaces. The interface number is always 0. |
port-channel port-channel-number |
Displays debug messages for the specified EtherChannel port-channel interface. The port-channel-number range is 1 to 48. |
vlan vlan-id |
Displays debug messages for the specified VLAN. The vlan range is 1 to 4094. |
counters |
Displays counters debugging information. |
exceptions |
Displays debug messages when a recoverable exceptional condition occurs during the computation of the interface packet and data rate statistics. |
protocol memory |
Displays debug messages for memory operations of protocol counters. |
states |
Displays intermediary debug messages when an interface's state transitions. |
Debugging is disabled.
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
If you do not specify a keyword, all debug messages appear.
The undebug interface command is the same as the no debug interface command.
When you enable debugging on a switch stack, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number EXEC command. Then enter the debug command at the command-line prompt of the stack member. You also can use the remote command stack-member-number LINE EXEC command on the stack master switch to enable debugging on a member switch without first starting a session.
To enable debugging of Link Layer Discovery Protocol (LLDP) packets, use the debug lldp packets command in privileged EXEC mode. To disable debugging, use the no form of this command.
debug lldp packets
no debug lldp packets
This command has no arguments or keywords.
Debugging is disabled.
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The undebug lldp packets command is the same as the no debug lldp packets command.
When you enable debugging on a switch stack, it is enabled only on the active switch. To enable debugging on a stack member, you can start a session from the active switch by using the session switch-number EXEC command.
To enable debugging of the Network Mobility Services Protocol (NMSP) on the switch, use the debug nmsp command in privileged EXEC mode. To disable debugging, use the no form of this command.
all |
Displays all NMSP debug messages. |
connection |
Displays debug messages for NMSP connection events. |
error |
Displays debugging information for NMSP error messages. |
event |
Displays debug messages for NMSP events. |
rx |
Displays debugging information for NMSP receive messages. |
tx |
Displays debugging information for NMSP transmit messages. |
packet |
Displays debug messages for NMSP packet events. |
Debugging is disabled.
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The undebug nmsp command is the same as the no debug nmsp command.
When you enable debugging on a switch stack, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number EXEC command. Then enter the debug command at the command-line prompt of the stack member. You also can use the remote command stack-member-number LINE EXEC command on the stack master switch to enable debugging on a member switch without first starting a session.
To enable debugging of the platform-dependent fallback bridging manager, use the debug platform fallback-bridging command in EXEC mode. To disable debugging, use the no form of this command.
debug platform fallback-bridging [ error | retry | rpc { events | messages } ]
no debug platform fallback-bridging [ error | retry | rpc { events | messages } ]
error |
(Optional) Displays fallback bridging manager error condition messages. |
retry |
(Optional) Displays fallback bridging manager retry messages. |
rpc {events | messages} |
(Optional) Displays fallback bridging debugging information. The keywords have these meanings: |
Debugging is disabled.
User EXEC
Privileged EXEC
If you do not specify a keyword, all fallback bridging manager debug messages appear.
The undebug platform fallback-bridging command is the same as the no debug platform fallback-bridging command.
When you enable debugging on a switch stack, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number EXEC command. Then enter the debug command at the command-line prompt of the stack member. You also can use the remote command stack-member-number LINE EXEC command on the stack master switch to enable debugging on a member switch without first starting a session.
Command |
Description |
---|---|
show debugging |
Displays information about the types of debugging that are enabled. |
To enable debugging of a Power over Ethernet (PoE) port, use the debug platform poe command in privileged EXEC mode. To disable debugging, use the no form of this command.
debug platform poe [ error | info ] [ switch switch-number ]
no debug platform poe [ error | info ] [ switch switch-number ]
error |
(Optional) Displays PoE-related error debug messages. |
info |
(Optional) Displays PoE-related information debug messages. |
switch switch-number |
(Optional) Specifies the stack member. This keyword is supported only on stacking-capable switches. |
Debugging is disabled.
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The undebug platform poe command is the same as the no debug platform poe command.
To enable debugging of platform-dependent port-security information, use the debug platform port-security command in EXEC mode. To disable debugging, use the no form of this command.
debug platform port-security { add | aging | all | delete | errors | rpc | warnings }
no debug platform port-security { add | aging | all | delete | errors | rpc | warnings }
add |
Displays secure address addition debug messages. |
aging |
Displays secure address aging debug messages. |
all |
Displays all port-security debug messages. |
delete |
Displays secure address deletion debug messages. |
errors |
Displays port-security error debug messages. |
rpc |
Displays remote procedure call (RPC) debug messages. |
warnings |
Displays warning debug messages. |
Debugging is disabled.
User EXEC
Privileged EXEC
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The undebug platform port-security command is the same as the no debug platform port-security command.
When you enable debugging on a switch stack, it is enabled only on the active switch. To enable debugging on a stack member, you can start a session from the active switch by using the session switch-number EXEC command.
To specify the duplex mode of operation for a port, use the duplex command in interface configuration mode. To return to the default value, use the no form of this command.
duplex { auto | full | half }
no duplex { auto | full | half }
auto |
Enables automatic duplex configuration. The port automatically detects whether it should run in full- or half-duplex mode, depending on the attached device mode. |
full |
Enables full-duplex mode. |
half |
Enables half-duplex mode (only for interfaces operating at 10 or 100 Mb/s). You cannot configure half-duplex mode for interfaces operating at 1000 or 10,000 Mb/s. |
The default is auto for Gigabit Ethernet ports.
You cannot configure the duplex mode on 10-Gigabit Ethernet ports; it is always full.
Duplex options are not supported on the 1000BASE-x or 10GBASE-x (where -x is -BX, -CWDM, -LX, -SX, or -ZX) small form-factor pluggable (SFP) modules.
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
For Gigabit Ethernet ports, setting the port to auto has the same effect as specifying full if the attached device does not autonegotiate the duplex parameter.
![]() Note | Half-duplex mode is supported on Gigabit Ethernet interfaces if the duplex mode is auto and the connected device is operating at half duplex. However, you cannot configure these interfaces to operate in half-duplex mode. |
Certain ports can be configured to be either full duplex or half duplex. How this command is applied depends on the device to which the switch is attached.
If both ends of the line support autonegotiation, we highly recommend using the default autonegotiation settings. If one interface supports autonegotiation and the other end does not, configure duplex and speed on both interfaces, and use the auto setting on the supported side.
If the speed is set to auto, the switch negotiates with the device at the other end of the link for the speed setting and then forces the speed setting to the negotiated value. The duplex setting remains as configured on each end of the link, which could result in a duplex setting mismatch.
You can configure the duplex setting when the speed is set to auto.
![]() Caution | Changing the interface speed and duplex mode configuration might shut down and reenable the interface during the reconfiguration. |
You can verify your setting by entering the show interfaces privileged EXEC command.
This example shows how to configure an interface for full-duplex operation:
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# duplex full
To enable error-disable detection for a specific cause or for all causes, use the errdisable detect cause command in global configuration mode. To disable the error-disable detection feature, use the no form of this command.
errdisable detect cause { all | arp-inspection | bpduguard shutdown vlan | dhcp-rate-limit | dtp-flap | gbic-invalid | inline-power | link-flap | loopback | pagp-flap | pppoe-ia-rate-limit | psp shutdown vlan | security-violation shutdown vlan | sfp-config-mismatch }
no errdisable detect cause { all | arp-inspection | bpduguard shutdown vlan | dhcp-rate-limit | dtp-flap | gbic-invalid | inline-power | link-flap | loopback | pagp-flap | pppoe-ia-rate-limit | psp shutdown vlan | security-violation shutdown vlan | sfp-config-mismatch }
all |
Enables error detection for all error-disabled causes. |
||
arp-inspection |
Enables error detection for dynamic Address Resolution Protocol (ARP) inspection. |
||
bpduguard shutdown vlan |
Enables per-VLAN error-disable for BPDU guard. |
||
dhcp-rate-limit |
Enables error detection for DHCP snooping. |
||
dtp-flap |
Enables error detection for the Dynamic Trunking Protocol (DTP) flapping. |
||
gbic-invalid |
Enables error detection for an invalid Gigabit Interface Converter (GBIC) module.
|
||
inline-power |
Enables error detection for the Power over Ethernet (PoE) error-disabled cause.
|
||
link-flap |
Enables error detection for link-state flapping. |
||
loopback |
Enables error detection for detected loopbacks. |
||
pagp-flap |
Enables error detection for the Port Aggregation Protocol (PAgP) flap error-disabled cause. |
||
pppoe-ia-rate-limit |
Enables error detection for the PPPoE Intermediate Agent rate-limit error-disabled cause. |
||
psp shutdown vlan |
Enables error detection for protocol storm protection (PSP). |
||
security-violation shutdown vlan |
Enables voice aware 802.1x security. |
||
sfp-config-mismatch |
Enables error detection on an SFP configuration mismatch. |
Detection is enabled for all causes. All causes, except per-VLAN error disabling, are configured to shut down the entire port.
Global configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
A cause (such as a link-flap or dhcp-rate-limit) is the reason for the error-disabled state. When a cause is detected on an interface, the interface is placed in an error-disabled state, an operational state that is similar to a link-down state.
When a port is error-disabled, it is effectively shut down, and no traffic is sent or received on the port. For the bridge protocol data unit (BPDU) guard, voice-aware 802.1x security, and port-security features, you can configure the switch to shut down only the offending VLAN on the port when a violation occurs, instead of shutting down the entire port.
If you set a recovery mechanism for the cause by entering the errdisable recovery global configuration command, the interface is brought out of the error-disabled state and allowed to retry the operation when all causes have timed out. If you do not set a recovery mechanism, you must enter the shutdown and then the no shutdown commands to manually recover an interface from the error-disabled state.
For protocol storm protection, excess packets are dropped for a maximum of two virtual ports. Virtual port error disabling using the psp keyword is not supported for EtherChannel and Flexlink interfaces.
To verify your settings, enter the show errdisable detect privileged EXEC command.
This example shows how to enable error-disabled detection for the link-flap error-disabled cause:
Switch(config)# errdisable detect cause link-flap
This command shows how to globally configure BPDU guard for a per-VLAN error-disabled state:
Switch(config)# errdisable detect cause bpduguard shutdown vlan
This command shows how to globally configure voice-aware 802.1x security for a per-VLAN error-disabled state:
Switch(config)# errdisable detect cause security-violation shutdown vlan
You can verify your setting by entering the
show
errdisable
detect privileged EXEC command.
To allow any switch port to be error disabled if incoming VLAN-tagged packets are small frames (67 bytes or less) and arrive at the minimum configured rate (the threshold), use the errdisable detect cause small-frame global configuration command on the switch stack or on a standalone switch. Use the no form of this command to return to the default setting.
errdisable detect cause small-frame
no errdisable detect cause small-frame
This command has no arguments or keywords.
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This command globally enables the small-frame arrival feature. Use the small violation-rate interface configuration command to set the threshold for each port.
You can configure the port to be automatically re-enabled by using the errdisable recovery cause small-frame global configuration command. You configure the recovery time by using the errdisable recovery interval interval global configuration command.
This example shows how to enable the switch ports to be put into the error-disabled mode if incoming small frames arrive at the configured threshold:
Switch(config)# errdisable detect cause small-frame
You can verify your setting by entering the show interfaces privileged EXEC command.
To enable the error-disabled mechanism to recover from a specific cause, use the errdisable recovery cause command in global configuration mode. To return to the default setting, use the no form of this command.
errdisable recovery cause { all | arp-inspection | bpduguard | channel-misconfig | dhcp-rate-limit | dtp-flap | gbic-invalid | inline-power | link-flap | loopback | mac-limit | pagp-flap | port-mode-failure | pppoe-ia-rate-limit | psecure-violation | psp | security-violation | sfp-config-mismatch | storm-control | udld | vmps }
no errdisable recovery cause { all | arp-inspection | bpduguard | channel-misconfig | dhcp-rate-limit | dtp-flap | gbic-invalid | inline-power | link-flap | loopback | mac-limit | pagp-flap | port-mode-failure | pppoe-ia-rate-limit | psecure-violation | psp | security-violation | sfp-config-mismatch | storm-control | udld | vmps }
all |
Enables the timer to recover from all error-disabled causes. |
||
arp-inspection |
Enables the timer to recover from the Address Resolution Protocol (ARP) inspection error-disabled state. |
||
bpduguard |
Enables the timer to recover from the bridge protocol data unit (BPDU) guard error-disabled state. |
||
channel-misconfig |
Enables the timer to recover from the EtherChannel misconfiguration error-disabled state. |
||
dhcp-rate-limit |
Enables the timer to recover from the DHCP snooping error-disabled state. |
||
dtp-flap |
Enables the timer to recover from the Dynamic Trunking Protocol (DTP) flap error-disabled state. |
||
gbic-invalid |
Enables the timer to recover from an invalid Gigabit Interface Converter (GBIC) module error-disabled state.
|
||
inline-power |
Enables the timer to recover from the Power over Ethernet (PoE) error-disabled state. This keyword is supported only on switches with PoE ports. |
||
link-flap |
Enables the timer to recover from the link-flap error-disabled state. |
||
loopback |
Enables the timer to recover from a loopback error-disabled state. |
||
mac-limit |
Enables the timer to recover from the mac limit error-disabled state. |
||
pagp-flap |
Enables the timer to recover from the Port Aggregation Protocol (PAgP)-flap error-disabled state. |
||
port-mode-failure |
Enables the timer to recover from the port mode change failure error-disabled state. |
||
pppoe-ia-rate-limit |
Enables the timer to recover from the PPPoE IA rate limit error-disabled state. |
||
psecure-violation |
Enables the timer to recover from a port security violation disable state. |
||
psp |
Enables the timer to recover from the protocol storm protection (PSP) error-disabled state. |
||
security-violation |
Enables the timer to recover from an IEEE 802.1x-violation disabled state. |
||
sfp-config-mismatch |
Enables error detection on an SFP configuration mismatch. |
||
storm-control |
Enables the timer to recover from a storm control error. |
||
udld |
Enables the timer to recover from the UniDirectional Link Detection (UDLD) error-disabled state. |
||
vmps |
Enables the timer to recover from the VLAN Membership Policy Server (VMPS) error-disabled state. |
Recovery is disabled for all causes.
Global configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
A cause (such as all or BDPU guard) is defined as the reason that the error-disabled state occurred. When a cause is detected on an interface, the interface is placed in the error-disabled state, an operational state similar to link-down state.
When a port is error-disabled, it is effectively shut down, and no traffic is sent or received on the port. For the BPDU guard and port-security features, you can configure the switch to shut down only the offending VLAN on the port when a violation occurs, instead of shutting down the entire port.
If you do not enable the recovery for the cause, the interface stays in the error-disabled state until you enter the shutdown and the no shutdown interface configuration commands. If you enable the recovery for a cause, the interface is brought out of the error-disabled state and allowed to retry the operation again when all the causes have timed out.
Otherwise, you must enter the shutdown and then the no shutdown commands to manually recover an interface from the error-disabled state.
You can verify your settings by entering the show errdisable recovery privileged EXEC command.
This example shows how to enable the recovery timer for the BPDU guard error-disabled cause:
Switch(config)# errdisable recovery cause bpduguard
Use the errdisable recovery cause small-frame global configuration command on the switch to enable the recovery timer for ports to be automatically re-enabled after they are error disabled by the arrival of small frames. Use the no form of this command to return to the default setting.
errdisable recovery cause small-frame
no errdisable recovery cause small-frame
This command has no arguments or keywords.
This feature is disabled.
Global configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This command enables the recovery timer for error-disabled ports. You configure the recovery time by using the errdisable recovery interval interface configuration command.
This example shows how to set the recovery timer:
Switch(config)# errdisable recovery cause small-frame
To specify the time to recover from an error-disabled state, use the errdisable recovery interval command in global configuration mode. To return to the default setting, use the no form of this command.
errdisable recovery interval timer-interval
no errdisable recovery interval timer-interval
timer-interval |
Time to recover from the error-disabled state. The range is 30 to 86400 seconds. The same interval is applied to all causes. The default interval is 300 seconds. |
The default recovery interval is 300 seconds.
Global configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The error-disabled recovery timer is initialized at a random differential from the configured interval value. The difference between the actual timeout value and the configured value can be up to 15 percent of the configured interval.
You can verify your settings by entering the show errdisable recovery privileged EXEC command.
This example shows how to set the timer to 500 seconds:
Switch(config)# errdisable recovery interval 500
To configure an interface, use the interface command.
interface { Auto-Template Auto-Template interface-number | Capwap Capwap interface-number | Gigabit Ethernet Gigabit Ethernet interface number | Group VI Group VI interface number Internal Interface Internal Interface number Loopback Loopback interface number Null Null interface Port-channel interface number Port-channel interface number TenGigabit Ethernet interface number Tunnel interface number Vlan interface number }
Auto-Template Auto-template interface-number |
Enables you to configure auto-template interface. Values range from 1 to 999. |
Capwap Capwap interface number |
Enables you to configure CAPWAP tunnel interface. Values range from 0 to 2147483647. |
GigabitEthernet Gigabit Ethernet interface number | Enables you to configure Gigabit Ethernet IEEE 802.3z interface. Values range from 0 to 9. |
Group VI Group VI interface number | Enables you to configure the internal interface. Values range from 0 to 9. |
Internal Interface Internal Interface | Enables you to configure internal interface. |
Loopback Loopback Interface number | Enables you to configure loopback interface. Values range from 0 to 2147483647. |
Null Null interface number | Enables you to configure null interface. Value is 0. |
Port-channel interface number | Enables you to configure Ethernet channel interfaces. Values range from 1 to 128. |
TenGigabitEthernet interface number | Enables you to configure a 10-Gigabit Ethernet interface. Values range from 0 to 9. |
Tunnel interface number | Enables you to configure the tunnel interface. Values range from 0 to 2147483647. |
Vlan interface number | Enables you to configure switch VLAN interfaces. Values range from 0 to 4098. |
None
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
You can not use the "no" form of this command.
This example shows how you can configure interface:
Switch# interface Tunnel 15
To configure an interface range, use the interface range command.
interface range { Gigabit Ethernet interface-number | | Loopback interface-number | Port Channel interface-number | TenGigabit Ethernet interface-number Tunnel interface-number Vlan interface-number Macro WORD }
GigabitEthernet interface-number |
Configures the Gigabit Ethernet IEEE 802.3z interface. Values range from 1 to 9. |
Loopback interface-number |
Configures the loopback interface. Values range from 0 to 2147483647. |
Port-Channel interface-number |
Configures 10-Gigabit Ethernet channel of interfaces. Values range from 1 to 128. |
TenGigabit Ethernet interface-number |
Configures 10-Gigabit Ethernet interfaces. Values range from 0 to 9. |
Tunnel interface-number |
Configures the tunnel interface. Values range from 0 to 2147483647. |
VLAN interface-number |
Configures the switch VLAN interfaces. Values range from 1 to 4095. |
Macro WORD |
Configures the keywords to interfaces. Support up to 32 characters. |
None
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how you can configure interface range:
Switch(config)# interface range vlan 1
To set the IP maximum transmission unit (MTU) size of routed packets on all routed ports of the switch or switch stack, use the ip mtu command in interface configuration mode. To restore the default IP MTU size, use the no form of this command.
ip mtu bytes
no ip mtu bytes
bytes |
MTU size, in bytes. The range is from 68 up to the system MTU value (in bytes). |
The default IP MTU size for frames received and sent on all switch interfaces is 1500 bytes.
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The upper limit of the IP value is based on the switch or switch stack configuration and refers to the currently applied system MTU value. For more information about setting the MTU sizes, see the system mtu global configuration command.
To return to the default IP MTU setting, you can apply the default ip mtu command or the no ip mtu command on the interface.
You can verify your setting by entering the show ip interface interface-id or show interfaces interface-id privileged EXEC command.
The following example sets the maximum IP packet size for VLAN 200 to 1000 bytes:
Switch(config)# interface vlan 200 Switch(config-if)# ip mtu 1000
The following example sets the maximum IP packet size for VLAN 200 to the default setting of 1500 bytes:
Switch(config)# interface vlan 200 Switch(config-if)# default ip mtu
This is an example of partial output from the show ip interface interface-id command. It displays the current IP MTU setting for the interface.
Switch# show ip interface gigabitethernet4/0/1
GigabitEthernet4/0/1 is up, line protocol is up
Internet address is 18.0.0.1/24
Broadcast address is 255.255.255.255
Address determined by setup command
MTU is 1500 bytes
Helper address is not set
<output truncated>
To set the IPv6 maximum transmission unit (MTU) size of routed packets on all routed ports of the switch or switch stack, use the ipv6 mtu command in interface configuration mode. To restore the default IPv6 MTU size, use the no form of this command.
ipv6 mtu bytes
no ipv6 mtu bytes
bytes |
MTU size, in bytes. The range is from 1280 up to the system MTU value (in bytes). |
The default IPv6 MTU size for frames received and sent on all switch interfaces is 1500 bytes.
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The upper limit of the IPv6 MTU value is based on the switch or switch stack configuration and refers to the currently applied system MTU value. For more information about setting the MTU sizes, see the system mtu global configuration command.
To return to the default IPv6 MTU setting, you can apply the default ipv6 mtu command or the no ipv6 mtu command on the interface.
You can verify your setting by entering the show ipv6 interface interface-id or show interface interface-id privileged EXEC command.
The following example sets the maximum IPv6 packet size for an interface to 2000 bytes:
Switch(config)# interface gigabitethernet4/0/1 Switch(config-if)# ipv6 mtu 2000
The following example sets the maximum IPv6 packet size for an interface to the default setting of 1500 bytes:
Switch(config)# interface gigabitethernet4/0/1 Switch(config-if)# default ipv6 mtu
This is an example of partial output from the show ipv6 interface interface-id command. It displays the current IPv6 MTU setting for the interface.
Switch# show ipv6 interface gigabitethernet4/0/1
GigabitEthernet4/0/1 is up, line protocol is up
Internet address is 18.0.0.1/24
Broadcast address is 255.255.255.255
Address determined by setup command
MTU is 1500 bytes
Helper address is not set
<output truncated>
To enable point-to-point tunneling on an access port, an IEEE 802.1Q tunnel port, or a port channel for Port Aggregation Protocol (PAgP), Link Aggregation Control Protocol (LACP), or UniDirectional Link Detection (UDLD) packets, use the l2protocol-tunnel point-to-point interface configuration command on the switch stack or on a standalone switch. To disable tunneling on the interface, use the no form of this command.
l2protocol-tunnel point-to-point [ pagp | lacp | udld]
no l2protocol-tunnel point-to-point [ pagp | lacp | udld]
The default is that no Layer 2 protocol packets are tunneled.
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must enter this command, with or without protocol types, to tunnel Layer 2 packets.
If you enter this command for a port channel, all ports in the channel must have the same configuration.
Layer 2 protocol tunneling across a service-provider network ensures that Layer 2 information is propagated across the network to all customer locations. When protocol tunneling is enabled, protocol packets are encapsulated with a well-known Cisco multicast address for transmission across the network. When the packets reach their destination, the well-known MAC address is replaced by the Layer 2 protocol MAC address.
In a service-provider network, you can use Layer 2 protocol tunneling to enhance the creation of EtherChannels by emulating a point-to-point network topology. When protocol tunneling is enabled on the service-provider switch for PAgP or LACP, remote customer switches receive the protocol data units (PDUs) and can negotiate automatic creation of EtherChannels.
To enable tunneling of PAgP, LACP, and UDLD packets, you must have a point-to-point network topology. To decrease the link-down detection time, you should also enable UDLD on the interface when you enable tunneling of PAgP or LACP packets.
You can enable point-to-point protocol tunneling for PAgP, LACP, and UDLD individually or for all three protocols.
Caution PAgP, LACP, and UDLD tunneling is only intended to emulate a point-to-point topology. An erroneous configuration that sends tunneled packets to many ports could lead to a network failure.
The configuration is saved in NVRAM.
For more information about Layer 2 protocol tunneling, see the software configuration guide for this release.
This example shows how to enable point-to-point protocol tunneling for PAgP and UDLD packets and to configure the PAgP drop threshold as 1000 packets per second:
Switch(config-if)# l2protocol-tunnel point-to-point pagp Switch(config-if)# l2protocol-tunnel point-to-point udld Switch(config-if)# l2protocol-tunnel drop-threshold point-to-point pagp 1000
To configure the maximum number of point-to-point tunneled packets that can be processed for the specified protocol before packets are dropped, use the l2protocol-tunnel drop-threshold point-to-point interface configuration command on the switch stack or on a standalone switch. To disable the drop threshold, use the no form of this command.
l2protocol-tunnel drop-threshold point-to-point [ pagp | lacp | udld] packets
no l2protocol-tunnel drop-threshold point-to-point [ pagp | lacp | udld] packets
The default is no drop threshold for the number of Layer 2 protocol packets.
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
Specify the drop-threshold to control the number of protocol packets per second that are received on an interface before it drops packets. When no protocol option is specified with a keyword, the threshold is applied to each of the tunneled Layer 2 protocol types. If you also set a shutdown threshold on the interface, the drop-threshold value must be less than or equal to the shutdown-threshold value.
When the drop threshold is reached, the interface drops Layer 2 protocol packets until the rate at which they are received is below the drop threshold.
The configuration is saved in NVRAM.
For more information about Layer 2 protocol tunneling, see the software configuration guide for this release.
This example shows how to enable point-to-point protocol tunneling for PAgP and UDLD packets and to configure the PAgP drop threshold as 1000 packets per second:
Switch(config-if)# l2protocol-tunnel point-to-point pagp Switch(config-if)# l2protocol-tunnel point-to-point udld Switch(config-if)# l2protocol-tunnel drop-threshold point-to-point pagp 1000
To configure the maximum number of point-to-point tunneled packets that can be received per second for the specified protocol before the interface shuts down, use the l2protocol-tunnel shutdown-threshold point-to-point interface configuration command on the switch stack or on a standalone switch. Use the no form of this command to disable the shutdown threshold.
l2protocol-tunnel shutdown-threshold point-to-point [ pagp | lacp | udld] packets
no l2protocol-tunnel shutdown-threshold point-to-point [ pagp | lacp | udld] packets
The default is no shutdown threshold for the number of Layer 2 protocol packets.
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
Enter the shutdown-threshold keyword to control the number of protocol packets per second that are received on an interface before it shuts down. When no protocol option is specified with the keyword, the threshold is applied to each of the tunneled Layer 2 protocol types. If you also set a drop threshold on the interface, the shutdown-threshold value must be greater than or equal to the drop-threshold value.
When the shutdown threshold is reached, the interface is error-disabled. If you enable error recovery by entering the errdisable recovery cause l2ptguard global configuration command, the interface is brought out of the error-disabled state and allowed to retry the operation again when all the causes have timed out. If the error recovery mechanism is not enabled for l2ptguard, the interface stays in the error-disabled state until you enter the shutdown and no shutdown interface configuration commands.
The configuration is saved in NVRAM.
For more information about Layer 2 protocol tunneling, see the software configuration guide for this release.
This example shows how to enable point-to-point protocol tunneling for PAgP and UDLD packets and to configure the PAgP shutdown threshold as 1000 packets per second:
Switch(config-if)# l2protocol-tunnel point-to-point pagp Switch(config-if)# l2protocol-tunnel point-to-point udld Switch(config-if)# l2protocol-tunnel shutdown-threshold point-to-point pagp 1000
To enable Link Layer Discovery Protocol (LLDP) on an interface, use the lldp command in interface configuration mode. To disable LLDP on an interface, use the no form of this command.
med-tlv-select |
Selects an LLDP Media Endpoint Discovery (MED) time-length-value (TLV) element to send. |
tlv |
String that identifies the TLV element. Valid values are the following: |
receive |
Enables the interface to receive LLDP transmissions. |
tlv-select |
Selects the LLDP TLVs to send. |
power-management |
Sends the LLDP Power Management TLV. |
transmit |
Enables LLDP transmission on the interface. |
LLDP is enabled on supported interfaces.
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This command is supported on 802.1 media types.
If the interface is configured as a tunnel port, LLDP is automatically disabled.
The following example shows how to disable LLDP transmission on an interface:
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# no lldp transmit
The following example shows how to enable LLDP transmission on an interface:
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# lldp transmit
To enable the logging of Power over Ethernet (PoE) events, use the logging event power-inline-status command in interface configuration mode. To disable the logging of PoE status events, use the no form of this command.
logging event power-inline-status
no logging event power-inline-status
This command has no arguments or keywords.
Logging of PoE events is enabled.
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The no form of this command does not disable PoE error events.
This example shows how to enable logging of PoE events on a port:
Switch(config-if)# interface gigabitethernet1/0/1 Switch(config-if)# logging event power-inline-status Switch(config-if)#
To enable the automatic medium-dependent interface crossover (auto-MDIX) feature on the interface, use the mdix auto command in interface configuration mode. To disable auto-MDIX, use the no form of this command.
mdix auto
no mdix auto
This command has no arguments or keywords.
Auto-MDIX is enabled.
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
When auto-MDIX is enabled, the interface automatically detects the required cable connection type (straight-through or crossover) and configures the connection appropriately.
When you enable auto-MDIX on an interface, you must also set the interface speed and duplex to auto so that the feature operates correctly.
When auto-MDIX (and autonegotiation of speed and duplex) is enabled on one or both of the connected interfaces, link up occurs, even if the cable type (straight-through or crossover) is incorrect.
Auto-MDIX is supported on all 10/100 and 10/100/1000 Mb/s interfaces and on 10/100/1000BASE-TX small form-factor pluggable (SFP) module interfaces. It is not supported on 1000BASE-SX or -LX SFP module interfaces.
You can verify the operational state of auto-MDIX on the interface by entering the show controllers ethernet-controller interface-id phy privileged EXEC command.
This example shows how to enable auto-MDIX on a port:
Switch# configure terminal Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# speed auto Switch(config-if)# duplex auto Switch(config-if)# mdix auto Switch(config-if)# end
To configure power stack mode for the power stack, use the mode command in power-stack configuration mode. To return to the default settings, use the no form of the command.
mode { power-shared | redundant } [strict]
no mode
power-shared |
Sets the power stack to operate in power-shared mode. This is the default. |
redundant |
Sets the power stack to operate in redundant mode. The largest power supply is removed from the power pool to be used as backup power in case one of the other power supplies fails. |
strict |
(Optional) Configures the power stack mode to run a strict power budget. The stack power needs cannot exceed the available power. |
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This command is available only on switch stacks running the IP Base or IP Services feature set.
To access power-stack configuration mode, enter the stack-power stack power stack name global configuration command.
Entering the no mode command sets the switch to the defaults of power-shared and non-strict mode.
In power-shared mode, all of the input power can be used for loads, and the total available power appears as one large power supply. The power budget includes all power from all supplies. No power is set aside for power supply failures. If a power supply fails, load shedding (shutting down of powered devices or switches) might occur.
In redundant mode, the largest power supply is removed from the power pool to use as backup power in case one of the other power supplies fails. The available power budget is the total power minus the largest power supply. This reduces the available power in the pool for switches and powered devices, but in case of a failure or an extreme power load, there is less chance of having to shut down switches or powered devices.
In strict mode, when a power supply fails and the available power drops below the budgeted power, the system balances the budget through load shedding of powered devices, even if the actual power is less than the available power. In nonstrict mode, the power stack can run in an over-allocated state and is stable as long as the actual power does not exceed the available power. In this mode, a powered device drawing more than normal power could cause the power stack to start shedding loads. This is normally not a problem because most devices do not run at full power. The chances of multiple powered devices in the stack requiring maximum power at the same time is small.
In both strict and nonstrict modes, power is denied when there is no power available in the power budget.
This is an example of setting the power stack mode for the stack named power1 to power-shared with strict power budgeting. All power in the stack is shared, but when the total available power is allotted, no more devices are allowed power.
Switch(config)# stack-power stack power1 Switch(config-stackpower)# mode power-shared strict Switch(config-stackpower)# exit
This is an example of setting the power stack mode for the stack named power2 to redundant. The largest power supply in the stack is removed from the power pool to provide redundancy in case one of the other supplies fails.
Switch(config)# stack-power stack power2 Switch(config-stackpower)# mode redundant Switch(config-stackpower)# exit
To apply a network-policy profile to an interface, use the network-policy command in interface configuration mode. To remove the policy, use the no form of this command.
network-policy profile-number
no network-policy
profile-number |
The network-policy profile number to apply to the interface. |
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
Use the network-policy profile number interface configuration command to apply a profile to an interface.
You cannot apply the switchport voice vlan command on an interface if you first configure a network-policy profile on it. However, if switchport voice vlan vlan-id is already configured on the interface, you can apply a network-policy profile on the interface. The interface then has the voice or voice-signaling VLAN network-policy profile applied.
This example shows how to apply network-policy profile 60 to an interface:
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# network-policy 60
To create a network-policy profile and to enter network-policy configuration mode, use the network-policy profile command in global configuration mode. To delete the policy and to return to global configuration mode, use the no form of this command.
network-policy profile profile-number
no network-policy profile profile-number
profile-number |
Network-policy profile number. The range is 1 to 4294967295. |
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
Use the network-policy profile global configuration command to create a profile and to enter network-policy profile configuration mode.
To return to privileged EXEC mode from the network-policy profile configuration mode, enter the exit command.
When you are in network-policy profile configuration mode, you can create the profile for voice and voice signaling by specifying the values for VLAN, class of service (CoS), differentiated services code point (DSCP), and tagging mode.
These profile attributes are contained in the Link Layer Discovery Protocol for Media Endpoint Devices (LLDP-MED) network-policy time-length-value (TLV).
This example shows how to create network-policy profile 60:
Switch(config)# network-policy profile 60 Switch(config-network-policy)#
To configure the network-policy profile created by using the network-policy profile global configuration command, use the network-policy profile configuration mode command. To delete a profile, use the no form of this command without additional parameters. To change its configured attributes, use the no form with parameters.
network-policy profile profile-number { voice | | voice-signaling } vlan [ vlan-id { cos cvalue | dscp dvalue } ] [ [ dot1p { cos cvalue | | dscp dvalue } ] | | none | | untagged ]
no network-policy profile profile-number { voice | | voice-signaling } vlan [ vlan-id { cos cvalue | dscp dvalue } ] [ [ dot1p { cos cvalue | | dscp dvalue } ] | | none | | untagged ]
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
Use the network-policy profile command to configure the attributes of a network-policy profile.
The voice application type is for dedicated IP phones and similar devices that support interactive voice services. These devices are typically deployed on a separate VLAN for ease of deployment and enhanced security through isolation from data applications.
The voice-signaling application type is for network topologies that require a different policy for voice signaling than for voice media. This application type should not be advertised if all of the same network policies apply as those advertised in the voice policy TLV.
This example shows how to configure the voice application type for VLAN 100 with a priority 4 CoS:
Switch(config)# network-policy profile 1 Switch(config-network-policy)# voice vlan 100 cos 4
This example shows how to configure the voice application type for VLAN 100 with a DSCP value of 34:
Switch(config)# network-policy profile 1 Switch(config-network-policy)# voice vlan 100 dscp 34
This example shows how to configure the voice application type for the native VLAN with priority tagging:
Switch(config-network-policy)# voice vlan dot1p cos 4
To suppress the reporting of attachment information from a specified interface, use the nmsp attachment suppress command in interface configuration mode. To return to the default setting, use the no form of this command.
nmsp attachment suppress
no nmsp attachment suppress
This command has no arguments or keywords.
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
Use the nmsp attachment suppress interface configuration command to configure an interface to not send location and attachment notifications to a Cisco Mobility Services Engine (MSE).
This example shows how to configure an interface to not send attachment information to the MSE:
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# nmsp attachment suppress
To configure Cisco StackPower power-priority values for a switch in a power stack and for its high-priority and low-priority PoE ports, use the power-priority command in switch stack-power configuration mode. To return to the default setting, use the no form of the command.
power-priority { high value | low value | switch value }
no power-priority { high | low | switch }
high value |
Sets the power priority for the ports configured as high-priority ports. The range is 1 to 27, with 1 as the highest priority. The high value must be lower than the value set for the low-priority ports and higher than the value set for the switch. |
low value |
Sets the power priority for the ports configured as low-priority ports. The range is 1 to 27. The low value must be higher than the value set for the high-priority ports and the value set for the switch. |
switch value |
Sets the power priority for the switch. The range is 1 to 27. The switch value must be lower than the values set for the low and high-priority ports. |
If no values are configured, the power stack randomly determines a default priority.
The default ranges are 1 to 9 for switches, 10 to 18 for high-priority ports, 19 to 27 for low-priority ports.
On non-PoE switches, the high and low values (for port priority) have no effect.
Switch stack-power configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
To access switch stack-power configuration mode, enter the stack-power switch switch-number global configuration command.
Cisco StackPower power-priority values determine the order for shutting down switches and ports when power is lost and load shedding must occur. Priority values are from 1 to 27; the highest numbers are shut down first.
We recommend that you configure different priority values for each switch and for its high priority ports and low priority ports to limit the number of devices shut down at one time during a loss of power. If you try to configure the same priority value on different switches in a power stack, the configuration is allowed, but you receive a warning message.
![]() Note | This command is available only on switch stacks running the IP Base or IP Services feature set. |
This is an example of setting the power priority for switch 1 in power stack a to 7, for the high-priority ports to 11, and for the low-priority ports to 20.
Switch(config)# stack-power switch 1 Switch(config-switch-stackpower)# stack-id power_stack_a Switch(config-switch-stackpower)# power-priority high 11 Switch(config-switch-stackpower)# power-priority low 20 Switch(config-switch-stackpower)# power-priority switch 7 Switch(config-switch-stackpower)# exit
To configure the power management mode on Power over Ethernet (PoE) ports, use the power inline command in interface configuration mode. To return to the default settings, use the no form of this command.
power inline { auto [ max max-wattage ] | never | port priority { high | low } | static [ max max-wattage ] }
no power inline { auto | never | port priority { high | low } | static [ max max-wattage ] }
auto |
Enables powered-device detection. If enough power is available, automatically allocates power to the PoE port after device detection. Allocation is first-come, first-serve. |
max max-wattage |
(Optional) Limits the power allowed on the port. The range is 4000 to 30000 mW. If no value is specified, the maximum is allowed. |
never |
Disables device detection, and disables power to the port. |
port |
Configures the power priority of the port. The default priority is low. |
priority {high|low} |
Sets the power priority of the port. In case of a power supply failure, ports configured as low priority are turned off first and ports configured as high priority are turned off last. The default priority is low. |
static |
Enables powered-device detection. Pre-allocates (reserves) power for a port before the switch discovers the powered device. This action guarantees that the device connected to the interface receives enough power. |
The default is auto (enabled).
The maximum wattage is 30,000 mW.
The default port priority is low.
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This command is supported only on PoE-capable ports. If you enter this command on a port that does not support PoE, this error message appears:
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# power inline auto ^ % Invalid input detected at '^' marker.
In a switch stack, this command is supported on all ports in the stack that support PoE.
Use the max max-wattage option to disallow higher-power powered devices. With this configuration, when the powered device sends Cisco Discovery Protocol (CDP) messages requesting more power than the maximum wattage, the switch removes power from the port. If the powered-device IEEE class maximum is greater than the maximum wattage, the switch does not power the device. The power is reclaimed into the global power budget.
![]() Note | The switch never powers any class 0 or class 3 device if the power inline max max-wattage command is configured for less than 30 W. |
If the switch denies power to a powered device (the powered device requests more power through CDP messages or if the IEEE class maximum is greater than the maximum wattage), the PoE port is in a power-deny state. The switch generates a system message, and the Oper column in the show power inline privileged EXEC command output shows power-deny.
Use the power inline static max max-wattage command to give a port high priority. The switch allocates PoE to a port configured in static mode before allocating power to a port configured in auto mode. The switch reserves power for the static port when it is configured rather than upon device discovery. The switch reserves the power on a static port even when there is no connected device and whether or not the port is in a shutdown or in a no shutdown state. The switch allocates the configured maximum wattage to the port, and the amount is never adjusted through the IEEE class or by CDP messages from the powered device. Because power is pre-allocated, any powered device that uses less than or equal to the maximum wattage is guaranteed power when it is connected to a static port. However, if the powered device IEEE class is greater than the maximum wattage, the switch does not supply power to it. If the switch learns through CDP messages that the powered device needs more than the maximum wattage, the powered device is shut down.
If the switch cannot pre-allocate power when a port is in static mode (for example, because the entire power budget is already allocated to other auto or static ports), this message appears: Command rejected: power inline static: pwr not available. The port configuration remains unchanged.
When you configure a port by using the power inline auto or the power inline static interface configuration command, the port autonegotiates by using the configured speed and duplex settings. This is necessary to determine the power requirements of the connected device (whether or not it is a powered device). After the power requirements have been determined, the switch hardcodes the interface by using the configured speed and duplex settings without resetting the interface.
When you configure a port by using the power inline never command, the port reverts to the configured speed and duplex settings.
If a port has a Cisco powered device connected to it, you should not use the power inline never command to configure the port. A false link-up can occur, placing the port in an error-disabled state.
Use the power inline port priority {high | low} command to configure the power priority of a PoE port. Powered devices connected to ports with low port priority are shut down first in case of a power shortage.
You can verify your settings by entering the show power inline EXEC command.
This example shows how to enable detection of a powered device and to automatically power a PoE port on a switch:
Switch(config)# interface gigabitethernet1/0/2 Switch(config-if)# power inline auto
This example shows how to configure a PoE port on a switch to allow a class 1 or a class 2 powered device:
Switch(config)# interface gigabitethernet1/0/2 Switch(config-if)# power inline auto max 7000
This example shows how to disable powered-device detection and to not power a PoE port on a switch:
Switch(config)# interface gigabitethernet1/0/2 Switch(config-if)# power inline never
This example shows how to set the priority of a port to high, so that it would be one of the last ports to be shut down in case of power supply failure:
Switch(config)# interface gigabitethernet1/0/2 Switch(config-if)# power inline port priority high
To override the amount of power specified by the IEEE classification for a powered device, use the power inline consumption command in global or interface configuration to specify the wattage used by each device. To return to the default power setting, use the no form of this command.
power inline consumption [default] wattage
no power inline consumption [default]
default |
The default keyword appears only in the global configuration. The command has the same effect with or without the keyword. |
wattage |
Specifies the power that the switch budgets for the port. The range is 4000 to 15400 mW. |
The default power on each Power over Ethernet (PoE) port is15400 mW.
Global configuration
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This command is supported only on the LAN Base image.
When Cisco powered devices are connected to PoE ports, the switch uses Cisco Discovery Protocol (CDP) to determine the CDP-specific power consumption of the devices, which is the amount of power to allocate based on the CDP messages. The switch adjusts the power budget accordingly. This does not apply to IEEE third-party powered devices. For these devices, when the switch grants a power request, the switch adjusts the power budget according to the powered-device IEEE classification. If the powered device is a class 0 (class status unknown) or a class 3, the switch budgets 15400 mW for the device, regardless of the CDP-specific amount of power needed.
If the powered device reports a higher class than its CDP-specific consumption or does not support power classification (defaults to class 0), the switch can power fewer devices because it uses the IEEE class information to track the global power budget.
With PoE+, powered devices use IEEE 802.3at and LLDP power with media dependent interface (MDI) type, length, and value descriptions (TLVs), Power-via-MDA TLVs, for negotiating power up to 30 W. Cisco pre-standard devices and Cisco IEEE powered devices can use CDP or the IEEE 802.3at power-via-MDI power negotiation mechanism to request power levels up to 30 W.
![]() Note | The initial allocation for Class 0, Class 3, and Class 4 powered devices is 15.4 W. When a device starts up and uses CDP or LLDP to send a request for more than 15.4 W, it can be allocated up to the maximum of 30 W. |
By using the power inline consumption wattage configuration command, you can override the default power requirement of the IEEE classification. The difference between what is mandated by the IEEE classification and what is actually needed by the device is reclaimed into the global power budget for use by additional devices. You can then extend the switch power budget and use it more effectively.
Before entering the power inline consumption wattage configuration command, we recommend that you enable policing of the real-time power consumption by using the power inline police [action log] interface configuration command.
![]() Caution | You should carefully plan your switch power budget and make certain not to oversubscribe the power supply. |
When you enter the power inline consumption default wattage or the no power inline consumption default global configuration command, or the power inline consumption wattage or the no power inline consumption interface configuration command, this caution message appears.
%CAUTION: Interface Gi1/0/1: Misconfiguring the 'power inline consumption/allocation' command may cause damage to the switch and void your warranty. Take precaution not to oversubscribe the power supply. It is recommended to enable power policing if the switch supports it. Refer to documentation.
![]() Note | When you manually configure the power budget, you must also consider the power loss over the cable between the switch and the powered device. |
For more information about the IEEE power classifications, see the “Configuring Interface Characteristics” chapter in the software configuration guide for this release.
This command is supported only on PoE-capable ports. If you enter this command on a switch or port that does not support PoE, an error message appears.
In a switch stack, this command is supported on all switches or ports in the stack that support PoE.
You can verify your settings by entering the show power inline consumption privileged EXEC command.
This example shows how to use the command in global configuration mode to configure the switch to budget 5000 mW to each PoE port:
Switch(config)# power inline consumption default 5000
%CAUTION: Interface Gi1/0/1: Misconfiguring the 'power inline consumption/allocation' command may cause damage to the switch and void your warranty. Take precaution not to oversubscribe the power supply.
It is recommended to enable power policing if the switch supports it.
Refer to documentation.
This example shows how to use the command in interface configuration mode to configure the switch to budget 12000 mW to the powered device connected to a specific PoE port:
Switch(config)# interface gigabitethernet1/0/2 Switch(config-if)# power inline consumption 12000 %CAUTION: Interface Gi1/0/2: Misconfiguring the 'power inline consumption/allocation' command may cause damage to the switch and void your warranty. Take precaution not to oversubscribe the power supply. It is recommended to enable power policing if the switch supports it. Refer to documentation.
To enable policing of real-time power consumption on a powered device, use the power inline police command in interface configuration mode. To disable this feature, use the no form of this command
power inline police [ action { errdisable | log } ]
no power inline police
action errdisable |
(Optional) Configures the switch to turn off power to the port if the real-time power consumption exceeds the maximum power allocation on the port. This is the default action. |
action log |
(Optional) Configures the switch to generate a syslog message while still providing power to a connected device if the real-time power consumption exceeds the maximum power allocation on the port. |
Policing of the real-time power consumption of the powered device is disabled.
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This command is supported only on the LAN Base image.
This command is supported only on Power over Ethernet (PoE)-capable ports. If you enter this command on a switch or port that does not support PoE, an error message appears.
In a switch stack, this command is supported on all switches or ports in the stack that support PoE and real-time power-consumption monitoring.
When policing of the real-time power consumption is enabled, the switch takes action when a powered device consumes more power than the allocated maximum amount.
When PoE is enabled, the switch senses the real-time power consumption of the powered device. This feature is called power monitoring or power sensing. The switch also polices the power usage with the power policing feature.
When power policing is enabled, the switch uses one of the these values as the cutoff power on the PoE port in this order:
The switch automatically sets the power usage of the device by using CDP power negotiation or by the IEEE classification and LLPD power negotiation.
If you do not manually configure the cutoff-power value, the switch automatically determines it by using CDP power negotiation or the device IEEE classification and LLDP power negotiation. If CDP or LLDP are not enabled, the default value of 30 W is applied. However without CDP or LLDP, the switch does not allow devices to consume more than 15.4 W of power because values from 15400 to 30000 mW are only allocated based on CDP or LLDP requests. If a powered device consumes more than 15.4 W without CDP or LLDP negotiation, the device might be in violation of the maximum current Imax limitation and might experience an Icut fault for drawing more current than the maximum. The port remains in the fault state for a time before attempting to power on again. If the port continuously draws more than 15.4 W, the cycle repeats.
When a powered device connected to a PoE+ port restarts and sends a CDP or LLDP packet with a power TLV, the switch locks to the power-negotiation protocol of that first packet and does not respond to power requests from the other protocol. For example, if the switch is locked to CDP, it does not provide power to devices that send LLDP requests. If CDP is disabled after the switch has locked on it, the switch does not respond to LLDP power requests and can no longer power on any accessories. In this case, you should restart the powered device.
If power policing is enabled, the switch polices power usage by comparing the real-time power consumption to the maximum power allocated on the PoE port. If the device uses more than the maximum power allocation (or cutoff power) on the port, the switch either turns power off to the port, or the switch generates a syslog message and updates the LEDs (the port LEDs are blinking amber) while still providing power to the device.
To configure the switch to turn off power to the port and put the port in the error-disabled state, use the power inline police interface configuration command.
To configure the switch to generate a syslog message while still providing power to the device, use the power inline police action log command.
If you do not enter the action log keywords, the default action is to shut down the port, turn off power to it, and put the port in the PoE error-disabled state. To configure the PoE port to automatically recover from the error-disabled state, use the errdisable detect cause inline-power global configuration command to enable error-disabled detection for the PoE cause and the errdisable recovery cause inline-power interval interval global configuration command to enable the recovery timer for the PoE error-disabled cause.
![]() Caution | If policing is disabled, no action occurs when the powered device consumes more than the maximum power allocation on the port, which could adversely affect the switch. |
You can verify your settings by entering the show power inline police privileged EXEC command.
This example shows how to enable policing of the power consumption and configuring the switch to generate a syslog message on the PoE port on a switch:
Switch(config)# interface gigabitethernet1/0/2 Switch(config-if)# power inline police action log
To configure and manage the internal power supplies on a switch, use the power supply command in privileged EXEC mode.
power supply stack-member-number slot { A | B } { off | on }
stack-member-number |
Stack member number for which to configure the internal power supplies. The range is 1 to 9, depending on the number of switches in the stack. This parameter is available only on stacking-capable switches. |
||
slot |
Selects the switch power supply to set. |
||
A |
Selects the power supply in slot A. |
||
B |
Selects the power supply in slot B.
|
||
off |
Sets the switch power supply to off. |
||
on |
Sets the switch power supply to on. |
The switch power supply is on.
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The power supply command applies to a switch or to a switch stack where all switches are the same platform.
In a switch stack with the same platform switches, you must specify the stack member before entering the slot {A | B} off or on keywords.
To return to the default setting, use the power supply stack-member-number on command.
You can verify your settings by entering the show env power privileged EXEC command.
This example shows how to set the power supply in slot A to off:
Switch> power supply 2 slot A off Disabling Power supply A may result in a power loss to PoE devices and/or switches ... Continue? (yes/[no]): yes Switch Jun 10 04:52:54.389: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 1 powered off Jun 10 04:52:56.717: %PLATFORM_ENV-1-FAN_NOT_PRESENT: Fan is not present
This example shows how to set the power supply in slot A to on:
Switch> power supply 1 slot B on
Jun 10 04:54:39.600: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 1 powered on
This example shows the output of the show env power command:
Switch> show env power
SW PID Serial# Status Sys Pwr PoE Pwr Watts
-- ------------------ ---------- --------------- ------- ------- -----
1A PWR-1RUC2-640WAC DCB1705B05B OK Good Good 250/390
1B Not Present
To control the rate at which protocol packets are sent to the switch, use the psp global configuration command to specify the upper threshold for the packet flow rate. The supported protocols are Address Resolution Protocol (ARP), ARP snooping, Dynamic Host Configuration Protocol (DHCP) v4, DHCP snooping, Internet Group Management Protocol (IGMP), and IGMP snooping. Use the no form of this command to disable protocol storm protection.
psp { arp | dhcp | igmp} pps value
no psp { arp | dhcp | igmp}
Specifies the threshold value for the number of packets per second. If the traffic exceeds this value, protocol storm protection is enforced. The range is from 5 to 50 packets per second. |
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
To set error-disable detection protocol storm protection, use the errdisable detect cause psp global configuration command.
When protocol storm protection is configured, a counter records the number of dropped packets. To see the number of dropped packets for a specific protocol, use the show psp statistics {arp | dhcp | igmp} privileged EXEC command. To see the number of dropped packets for all protocols, use the show psp statistics all command. To clear the counter for a protocol, use the clear psp counter [arp | dhcp | igmp] command.
To display all the CAPWAP tunnels established by the controller to access points and other mobility controllers use the show CAPWAP summary command.
show CAPWAP summary
This command has no arguments or keywords.
None
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to display CAPWAP tunnels established by the controllers to the access points and other controllers.
Switch# show capwap summary
CAPWAP Tunnels General Statistics:
Number of Capwap Data Tunnels = 8
Number of Capwap Mobility Tunnels = 0
Number of Capwap Multicast Tunnels = 0
Name APName Type PhyPortIf Mode McastIf
------ -------------------------------- ---- --------- ---------
-------
Ca4 AP-Behind-Router data - unicast -
Ca0 AP1142-kat data - unicast -
Ca5 APRFCHAMBER2-EDISON data - unicast -
Ca6 KATANA_2_RF data - unicast -
Ca1 AP-1040-RF data - unicast -
Ca7 KATANA_1_RF data - unicast -
Ca2 AP3500-2027 data - unicast -
Ca3 AP-1040-out data - unicast -
To display the state of the CPU network interface ASIC and the send and receive statistics for packets reaching the CPU, use the show controllers cpu-interface command in privileged EXEC mode.
show controllers cpu-interface [ switch stack-member-number ]
switch stack-member-number |
(Optional) Specifies the stack member number. |
None
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This display provides information that might be useful for Cisco technical support representatives troubleshooting the switch.
This is a partial output example from the show controllers cpu-interface command:
Switch# show controllers cpu-interface switch 1
cpu-queue-frames retrieved dropped invalid hol-block
---------------- --------- ------- ------- ---------
Routing Protocol 0 0 0 0
L2 Protocol 241567 0 0 0
sw forwarding 0 0 0 0
broadcast 68355 0 0 0
icmp 0 0 0 0
icmp redirect 0 0 0 0
logging 0 0 0 0
rpf-fail 0 0 0 0
DOT1X authentication 328174 0 0 0
Forus Traffic 0 0 0 0
Forus Resolution 0 0 0 0
Wireless q5 0 0 0 0
Wireless q1 0 0 0 0
Wireless q2 0 0 0 0
Wireless q3 0 0 0 0
Wireless q4 0 0 0 0
Learning cache 0 0 0 0
Topology control 820408 0 0 0
Proto snooping 0 0 0 0
BFD Low latency 0 0 0 0
Transit Traffic 0 0 0 0
Multi End station 0 0 0 0
Health Check 0 0 0 0
Crypto control 0 0 0 0
Exception 0 0 0 0
General Punt 0 0 0 0
NFL sampled data 0 0 0 0
STG cache 0 0 0 0
EGR exception 0 0 0 0
show forward 0 0 0 0
Multicast data 0 0 0 0
Gold packet 0 0 0 0
To display the internal Media Access Control Security (MACsec) counters or registers on the device, use the show controllers ethernet phy macsec command in privileged EXEC mode.
show controllers ethernet [ interface-id] phy macsec { counters | registers}
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
The displayed information is useful for Cisco technical support representatives troubleshooting the switch.
This is an example output from the show controllers ethernet phy macsec counters command:
Switch# show controllers ethernet gigabitethernet1/0/1 phy macsec counters GigabitEthernet1/0/1 (gpn: 1, port-number: 1) ----------------------------------------------------------- ========== Active RX SA ========== ILU Entry : 1 SCI : 0x1B2140EC4C0000 AN : 0x0000 NextPN : 0x0013 Decrypt Key : 0x1E902BE3AF08549BAC995474C5F55526 ========== RX SA Stats ========== IGR_HIT : 0xE IGR_OK : 0xE IGR_UNCHK : 0x0 IGR_DELAY : 0x0 IGR_LATE : 0x0 IGR_INVLD : 0x0 IGR_NOTVLD : 0x0 ========== Active TX SA ========== ELU Entry : 2 SCI : 0x22BDCF9A010002 AN : 0x0000 NextPN : 0x0022 Encrypt Key : 0x1E902BE3AF08549BAC995474C5F55526 ========== TX SA Stats ========== EGR_HIT : 0x682 EGR_PKT_PROT : 0x0 EGR_PKT_ENC : 0x682 ========== Port Stats ========== IGR_UNTAG : 0x0 IGR_NOTAG : 0x57B IGR_BADTAG : 0x0 IGR_UNKSCI : 0x0 IGR_MISS : 0x52B 00-10-18, 03-06, 01-02
This is an example output from the show controllers ethernet phy macsec registers command:
Switch# show controllers ethernet gigabitethernet1/0/1 phy macsec registers GigabitEthernet1/0/1 (gpn: 1, port-number: 1) ----------------------------------------------------------- Macsec Registers ----------------------------------------------------------- 0000: 88E58100 Ethertypes Register 0001: 00400030 Sizes Register 0002: 00000010 Cfg Default Vlan 0003: 00000000 Reset Control Register 0007: 00000001 Port Number Register 0009: 0000100C EGR Gen Register 000B: 2FB40000 IGR Gen Register 000E: 00000000 Replay Window Register 0010: 00000047 ISC Gen Register 001C: 00000000 LC Interrupt Register 001D: 0000003A LC Interrupt Mask Register 001E: 00000000 FIPS Control Register 001F: 00000F0F ET Match Control Register 0030: 888E8808 ET Match 0 Register 0031: 88CC8809 ET Match 1 Register 0032: 00000000 ET Match 2 Register 0033: 00000000 ET Match 3 Register 0040: 00019C49 Wire Mac Control 0 Register 0041: 000200C1 Wire Mac Control 1 Register 0042: 00000008 Wire Mac Control 2 Register 0043: 00000020 Wire Mac Autneg Control Regist 0047: 0007FE43 Wire Mac Hidden0 Register 0050: 00009FC9 Sys Mac Control 0 Register 0051: 000100B1 Sys Mac Control 1 Register 0052: 00000000 Sys Mac Control 2 Register 0053: 00000030 Sys Mac Autneg Control Registe 0057: 0007FE43 Sys Mac Hidden0 Register 0070: 00000040 SLC Cfg Gen Register 0074: 00000004 Pause Control Register 0076: 00002006 SLC Ram Control Register 0060: 00000004 CiscoIP Enable Register 00-10-18, 03-06, 01-02
To display per-interface send and receive statistics read from the hardware with keywords, use the show controllers ethernet-controller command in EXEC mode.
show controllers ethernet-controller [ interface-id ] [ down-when-looped | phy [ detail ] ] [ port-asic statistics { exceptions | interface interface-id { l2 | l3 } | l3-ifid if-id | port-ifid if-id | vlan-ifid if-id } [ switch stack-member-number ] [ asic asic-number ] ]
interface-id |
(Optional) ID of the physical interface. |
down-when-looped |
(Optional) Displays states related to down-when-looped detection. |
phy |
(Optional) Displays the status of the internal registers on the switch physical layer device (PHY) for the device or the interface. This display includes the operational state of the automatic medium-dependent interface crossover (auto-MDIX) feature on an interface. |
detail |
(Optional) Displays details about the PHY internal registers. |
port-asic |
(Optional) Displays information about the port ASIC internal registers. |
statistics |
Displays port ASIC statistics, including the Rx/Sup Queue and miscellaneous statistics. |
exceptions |
Displays port ASIC exception statistics. |
interface interface-id |
Specifies the interface for which to display port ASIC statistics. |
l2 |
Displays statistics for the Layer 2 interface. |
l3 |
Displays statistics for the Layer 3 interface. |
l3-ifid if-id |
Specifies the Layer 3 IF interface ID for which to display port ASIC statistics. |
port-ifid if-id |
Specifies the PortIF interface ID for which to display port ASIC statistics. |
vlan-ifid if-id |
Specifies the VLANIF interface ID for which to display port ASIC statistics. |
switch stack-member-number |
(Optional) Specifies the stack member number for which to display send and receive statistics. |
asic asic-number |
(Optional) Specifies the ASIC number. |
User EXEC (only supported with the interface-id keywords in user EXEC mode)
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
Without keywords, this command provides the RMON statistics for all interfaces or for the specified interface.
To display the interface internal registers, use the phy keyword. To display information about the port ASIC, use the port-asic keyword.
When you enter the phy or port-asic keywords, the displayed information is useful primarily for Cisco technical support representatives troubleshooting the switch.
This is an example of output from the show controllers ethernet-controller command for an interface:
Switch# show controllers ethernet-controller gigabitethernet6/0/1
Transmit GigabitEthernet6/0/1 Receive
0 Bytes 0 Bytes
0 Unicast frames 0 Unicast frames
0 Multicast frames 0 Multicast frames
0 Broadcast frames 0 Broadcast frames
0 Too old frames 0 Unicast bytes
0 Deferred frames 0 Multicast bytes
0 MTU exceeded frames 0 Broadcast bytes
0 1 collision frames 0 Alignment errors
0 2 collision frames 0 FCS errors
0 3 collision frames 0 Oversize frames
0 4 collision frames 0 Undersize frames
0 5 collision frames 0 Collision fragments
0 6 collision frames
0 7 collision frames 0 Minimum size frames
0 8 collision frames 0 65 to 127 byte frames
0 9 collision frames 0 128 to 255 byte frames
0 10 collision frames 0 256 to 511 byte frames
0 11 collision frames 0 512 to 1023 byte frames
0 12 collision frames 0 1024 to 1518 byte frames
0 13 collision frames 0 Overrun frames
0 14 collision frames 0 Pause frames
0 15 collision frames 0 Symbol error frames
0 Excessive collisions
0 Late collisions 0 Invalid frames, too large
0 VLAN discard frames 0 Valid frames, too large
0 Excess defer frames 0 Invalid frames, too small
0 64 byte frames 0 Valid frames, too small
0 127 byte frames
0 255 byte frames 0 Too old frames
0 511 byte frames 0 Valid oversize frames
0 1023 byte frames 0 System FCS error frames
0 1518 byte frames 0 RxPortFifoFull drop frame
0 Too large frames
0 Good (1 coll) frames
Field |
Description |
---|---|
Bytes |
The total number of bytes sent on an interface. |
Unicast Frames |
The total number of frames sent to unicast addresses. |
Multicast frames |
The total number of frames sent to multicast addresses. |
Broadcast frames |
The total number of frames sent to broadcast addresses. |
Too old frames |
The number of frames dropped on the egress port because the packet aged out. |
Deferred frames |
The number of frames that are not sent after the time exceeds 2*maximum-packet time. |
MTU exceeded frames |
The number of frames that are larger than the maximum allowed frame size. |
1 collision frames |
The number of frames that are successfully sent on an interface after one collision occurs. |
2 collision frames |
The number of frames that are successfully sent on an interface after two collisions occur. |
3 collision frames |
The number of frames that are successfully sent on an interface after three collisions occur. |
4 collision frames |
The number of frames that are successfully sent on an interface after four collisions occur. |
5 collision frames |
The number of frames that are successfully sent on an interface after five collisions occur. |
6 collision frames |
The number of frames that are successfully sent on an interface after six collisions occur. |
7 collision frames |
The number of frames that are successfully sent on an interface after seven collisions occur. |
8 collision frames |
The number of frames that are successfully sent on an interface after eight collisions occur. |
9 collision frames |
The number of frames that are successfully sent on an interface after nine collisions occur. |
10 collision frames |
The number of frames that are successfully sent on an interface after ten collisions occur. |
11 collision frames |
The number of frames that are successfully sent on an interface after 11 collisions occur. |
12 collision frames |
The number of frames that are successfully sent on an interface after 12 collisions occur. |
13 collision frames |
The number of frames that are successfully sent on an interface after 13 collisions occur. |
14 collision frames |
The number of frames that are successfully sent on an interface after 14 collisions occur. |
15 collision frames |
The number of frames that are successfully sent on an interface after 15 collisions occur. |
Excessive collisions |
The number of frames that could not be sent on an interface after 16 collisions occur. |
Late collisions |
After a frame is sent, the number of frames dropped because late collisions were detected while the frame was sent. |
VLAN discard frames |
The number of frames dropped on an interface because the CFI1 bit is set. |
Excess defer frames |
The number of frames that are not sent after the time exceeds the maximum-packet time. |
64 byte frames |
The total number of frames sent on an interface that are 64 bytes. |
127 byte frames |
The total number of frames sent on an interface that are from 65 to 127 bytes. |
255 byte frames |
The total number of frames sent on an interface that are from 128 to 255 bytes. |
511 byte frames |
The total number of frames sent on an interface that are from 256 to 511 bytes. |
1023 byte frames |
The total number of frames sent on an interface that are from 512 to 1023 bytes. |
1518 byte frames |
The total number of frames sent on an interface that are from 1024 to 1518 bytes. |
Too large frames |
The number of frames sent on an interface that are larger than the maximum allowed frame size. |
Good (1 coll) frames |
The number of frames that are successfully sent on an interface after one collision occurs. This value does not include the number of frames that are not successfully sent after one collision occurs. |
Field |
Description |
---|---|
Bytes |
The total amount of memory (in bytes) used by frames received on an interface, including the FCS2 value and the incorrectly formed frames. This value excludes the frame header bits. |
Unicast frames |
The total number of frames successfully received on the interface that are directed to unicast addresses. |
Multicast frames |
The total number of frames successfully received on the interface that are directed to multicast addresses. |
Broadcast frames |
The total number of frames successfully received on an interface that are directed to broadcast addresses. |
Unicast bytes |
The total amount of memory (in bytes) used by unicast frames received on an interface, including the FCS value and the incorrectly formed frames. This value excludes the frame header bits. |
Multicast bytes |
The total amount of memory (in bytes) used by multicast frames received on an interface, including the FCS value and the incorrectly formed frames. This value excludes the frame header bits. |
Broadcast bytes |
The total amount of memory (in bytes) used by broadcast frames received on an interface, including the FCS value and the incorrectly formed frames. This value excludes the frame header bits. |
Alignment errors |
The total number of frames received on an interface that have alignment errors. |
FCS errors |
The total number of frames received on an interface that have a valid length (in bytes) but do not have the correct FCS values. |
Oversize frames |
The number of frames received on an interface that are larger than the maximum allowed frame size. |
Undersize frames |
The number of frames received on an interface that are smaller than 64 bytes. |
Collision fragments |
The number of collision fragments received on an interface. |
Minimum size frames |
The total number of frames that are the minimum frame size. |
65 to 127 byte frames |
The total number of frames that are from 65 to 127 bytes. |
128 to 255 byte frames |
The total number of frames that are from 128 to 255 bytes. |
256 to 511 byte frames |
The total number of frames that are from 256 to 511 bytes. |
512 to 1023 byte frames |
The total number of frames that are from 512 to 1023 bytes. |
1024 to 1518 byte frames |
The total number of frames that are from 1024 to 1518 bytes. |
Overrun frames |
The total number of overrun frames received on an interface. |
Pause frames |
The number of pause frames received on an interface. |
Symbol error frames |
The number of frames received on an interface that have symbol errors. |
Invalid frames, too large |
The number of frames received that were larger than maximum allowed MTU3 size (including the FCS bits and excluding the frame header) and that have either an FCS error or an alignment error. |
Valid frames, too large |
The number of frames received on an interface that are larger than the maximum allowed frame size. |
Invalid frames, too small |
The number of frames received that are smaller than 64 bytes (including the FCS bits and excluding the frame header) and that have either an FCS error or an alignment error. |
Valid frames, too small |
The number of frames received on an interface that are smaller than 64 bytes (or 68 bytes for VLAN-tagged frames) and that have valid FCS values. The frame size includes the FCS bits but excludes the frame header bits. |
Too old frames |
The number of frames dropped on the ingress port because the packet aged out. |
Valid oversize frames |
The number of frames received on an interface that are larger than the maximum allowed frame size and have valid FCS values. The frame size includes the FCS value but does not include the VLAN tag. |
System FCS error frames |
The total number of frames received on an interface that have a valid length (in bytes) but that do not have the correct FCS values. |
RxPortFifoFull drop frames |
The total number of frames received on an interface that are dropped because the ingress queue is full. |
This is an example of output from the show controllers ethernet-controller phy command for a specific interface:
Switch# show controllers ethernet-controller gigabitethernet1/0/2 phy
Control Register : 0001 0001 0100 0000
Control STATUS : 0111 1001 0100 1001
Phy ID 1 : 0000 0001 0100 0001
Phy ID 2 : 0000 1100 0010 0100
Auto-Negotiation Advertisement : 0000 0011 1110 0001
Auto-Negotiation Link Partner : 0000 0000 0000 0000
Auto-Negotiation Expansion Reg : 0000 0000 0000 0100
Next Page Transmit Register : 0010 0000 0000 0001
Link Partner Next page Registe : 0000 0000 0000 0000
1000BASE-T Control Register : 0000 1111 0000 0000
1000BASE-T Status Register : 0100 0000 0000 0000
Extended Status Register : 0011 0000 0000 0000
PHY Specific Control Register : 0000 0000 0111 1000
PHY Specific Status Register : 1000 0001 0100 0000
Interrupt Enable : 0000 0000 0000 0000
Interrupt Status : 0000 0000 0100 0000
Extended PHY Specific Control : 0000 1100 0110 1000
Receive Error Counter : 0000 0000 0000 0000
Reserved Register 1 : 0000 0000 0000 0000
Global Status : 0000 0000 0000 0000
LED Control : 0100 0001 0000 0000
Manual LED Override : 0000 1000 0010 1010
Extended PHY Specific Control : 0000 0000 0001 1010
Disable Receiver 1 : 0000 0000 0000 1011
Disable Receiver 2 : 1000 0000 0000 0100
Extended PHY Specific Status : 1000 0100 1000 0000
Auto-MDIX : On [AdminState=1 Flags=0x00052248]
This is an example of output from the show controllers ethernet-controller tengigabitethernet1/0/1 phy command:
Switch# show controllers ethernet-controller tengigabitethernet1/0/1 phy
TenGigabitEthernet1/0/1 (gpn: 29, port-number: 1)
-----------------------------------------------------------
X2 Serial EEPROM Contents:
Non-Volatile Register (NVR) Fields
X2 MSA Version supported :0x1E
NVR Size in bytes :0x100
Number of bytes used :0x100
Basic Field Address :0xB
Customer Field Address :0x77
Vendor Field Address :0xA7
Extended Vendor Field Address :0x100
Reserved :0x0
Transceiver type :0x2 =X2
Optical connector type :0x1 =SC
Bit encoding:0x1 =NRZ
Normal BitRate in multiple of 1M b/s :0x2848
Protocol Type:0x1 =10GgE
Standards Compliance Codes :
10GbE Code Byte 0 :0x4 =10GBASE-ER
10GbE Code Byte 1 :0x0
SONET/SDH Code Byte 0:0x0
SONET/SDH Code Byte 1:0x0
SONET/SDH Code Byte 2:0x0
SONET/SDH Code Byte 3:0x0
10GFC Code Byte 0 :0x0
10GFC Code Byte 1 :0x0
10GFC Code Byte 2 :0x0
10GFC Code Byte 3 :0x0
Transmission range in10m :0xFA0
Fibre Type :
Fibre Type Byte 0 :0x20 =SM, Generic
Fibre Type Byte 1 :0x0 =Unspecified
<output truncated>
This is an example of output from the show controllers ethernet-controller port-asic configuration command:
Switch# show controllers ethernet-controller port-asic configuration
========================================================================
Switch 1, PortASIC 0 Registers
------------------------------------------------------------------------
DeviceType : 000101BC
Reset : 00000000
PmadMicConfig : 00000001
PmadMicDiag : 00000003
SupervisorReceiveFifoSramInfo : 000007D0 000007D0 40000000
SupervisorTransmitFifoSramInfo : 000001D0 000001D0 40000000
GlobalStatus : 00000800
IndicationStatus : 00000000
IndicationStatusMask : FFFFFFFF
InterruptStatus : 00000000
InterruptStatusMask : 01FFE800
SupervisorDiag : 00000000
SupervisorFrameSizeLimit : 000007C8
SupervisorBroadcast : 000A0F01
GeneralIO : 000003F9 00000000 00000004
StackPcsInfo : FFFF1000 860329BD 5555FFFF FFFFFFFF
FF0FFF00 86020000 5555FFFF 00000000
StackRacInfo : 73001630 00000003 7F001644 00000003
24140003 FD632B00 18E418E0 FFFFFFFF
StackControlStatus : 18E418E0
stackControlStatusMask : FFFFFFFF
TransmitBufferFreeListInfo : 00000854 00000800 00000FF8 00000000
0000088A 0000085D 00000FF8 00000000
TransmitRingFifoInfo : 00000016 00000016 40000000 00000000
0000000C 0000000C 40000000 00000000
TransmitBufferInfo : 00012000 00000FFF 00000000 00000030
TransmitBufferCommonCount : 00000F7A
TransmitBufferCommonCountPeak : 0000001E
TransmitBufferCommonCommonEmpty : 000000FF
NetworkActivity : 00000000 00000000 00000000 02400000
DroppedStatistics : 00000000
FrameLengthDeltaSelect : 00000001
SneakPortFifoInfo : 00000000
MacInfo : 0EC0801C 00000001 0EC0801B 00000001
00C0001D 00000001 00C0001E 00000001
<output truncated>
This is an example of output from the show controllers ethernet-controller port-asic statistics command:
Switch# show controllers ethernet-controller port-asic statistics
===========================================================================
Switch 1, PortASIC 0 Statistics
---------------------------------------------------------------------------
0 RxQ-0, wt-0 enqueue frames 0 RxQ-0, wt-0 drop frames
4118966 RxQ-0, wt-1 enqueue frames 0 RxQ-0, wt-1 drop frames
0 RxQ-0, wt-2 enqueue frames 0 RxQ-0, wt-2 drop frames
0 RxQ-1, wt-0 enqueue frames 0 RxQ-1, wt-0 drop frames
296 RxQ-1, wt-1 enqueue frames 0 RxQ-1, wt-1 drop frames
2836036 RxQ-1, wt-2 enqueue frames 0 RxQ-1, wt-2 drop frames
0 RxQ-2, wt-0 enqueue frames 0 RxQ-2, wt-0 drop frames
0 RxQ-2, wt-1 enqueue frames 0 RxQ-2, wt-1 drop frames
158377 RxQ-2, wt-2 enqueue frames 0 RxQ-2, wt-2 drop frames
0 RxQ-3, wt-0 enqueue frames 0 RxQ-3, wt-0 drop frames
0 RxQ-3, wt-1 enqueue frames 0 RxQ-3, wt-1 drop frames
0 RxQ-3, wt-2 enqueue frames 0 RxQ-3, wt-2 drop frames
15 TxBufferFull Drop Count 0 Rx Fcs Error Frames
0 TxBufferFrameDesc BadCrc16 0 Rx Invalid Oversize Frames
0 TxBuffer Bandwidth Drop Cou 0 Rx Invalid Too Large Frames
0 TxQueue Bandwidth Drop Coun 0 Rx Invalid Too Large Frames
0 TxQueue Missed Drop Statist 0 Rx Invalid Too Small Frames
74 RxBuffer Drop DestIndex Cou 0 Rx Too Old Frames
0 SneakQueue Drop Count 0 Tx Too Old Frames
0 Learning Queue Overflow Fra 0 System Fcs Error Frames
0 Learning Cam Skip Count
15 Sup Queue 0 Drop Frames 0 Sup Queue 8 Drop Frames
0 Sup Queue 1 Drop Frames 0 Sup Queue 9 Drop Frames
0 Sup Queue 2 Drop Frames 0 Sup Queue 10 Drop Frames
0 Sup Queue 3 Drop Frames 0 Sup Queue 11 Drop Frames
0 Sup Queue 4 Drop Frames 0 Sup Queue 12 Drop Frames
0 Sup Queue 5 Drop Frames 0 Sup Queue 13 Drop Frames
0 Sup Queue 6 Drop Frames 0 Sup Queue 14 Drop Frames
0 Sup Queue 7 Drop Frames 0 Sup Queue 15 Drop Frames
===========================================================================
Switch 1, PortASIC 1 Statistics
---------------------------------------------------------------------------
0 RxQ-0, wt-0 enqueue frames 0 RxQ-0, wt-0 drop frames
52 RxQ-0, wt-1 enqueue frames 0 RxQ-0, wt-1 drop frames
0 RxQ-0, wt-2 enqueue frames 0 RxQ-0, wt-2 drop frames
<output truncated>
To display the values in the registers of the specified Power over Ethernet (PoE) controller, use the show controllers power inline EXEC command.
show controllers power inline [instance] [ module switch-number ]
instance |
(Optional) Power controller instance, where each instance corresponds to four ports. The possible range is 0 to 11, depending on the number of ports. |
module switch number |
(Optional) Limits the display to ports on the specified stack member. The switch number is 1 to 9. This keyword is available only on stacking-capable switches. |
Privileged EXEC
User EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
Though visible on all switches, this command is valid only for PoE switches. It provides no information for switches that do not support PoE.
The output provides information that might be useful for Cisco technical support representatives troubleshooting the switch.
To display the state of the registers for all hardware memory in the system and for all hardware interface ASICs that are content-addressable memory-controllers, use the show controllers tcam privileged EXEC command.
show controllers tcam [asic [number]] [detail]
asic |
(Optional) Displays port ASIC hardware information. |
number |
(Optional) Displays information for the specified port ASIC number. The range is from 0 to 15. |
detail |
(Optional) Displays detailed hardware register information. |
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This display provides information that might be useful for Cisco technical support representatives troubleshooting the switch.
This is an example of output from the show controllers tcam command:
Switch# show controllers tcam
------------------------------------------------------------------------
TCAM-0 Registers
------------------------------------------------------------------------
REV: 00B30103
SIZE: 00080040
ID: 00000000
CCR: 00000000_F0000020
RPID0: 00000000_00000000
RPID1: 00000000_00000000
RPID2: 00000000_00000000
RPID3: 00000000_00000000
HRR0: 00000000_E000CAFC
HRR1: 00000000_00000000
HRR2: 00000000_00000000
HRR3: 00000000_00000000
HRR4: 00000000_00000000
HRR5: 00000000_00000000
HRR6: 00000000_00000000
HRR7: 00000000_00000000
<output truncated>
GMR31: FF_FFFFFFFF_FFFFFFFF
GMR32: FF_FFFFFFFF_FFFFFFFF
GMR33: FF_FFFFFFFF_FFFFFFFF
=============================================================================
TCAM related PortASIC 1 registers
=============================================================================
LookupType: 89A1C67D_24E35F00
LastCamIndex: 0000FFE0
LocalNoMatch: 000069E0
ForwardingRamBaseAddress:
00022A00 0002FE00 00040600 0002FE00 0000D400
00000000 003FBA00 00009000 00009000 00040600
00000000 00012800 00012900
To display bandwidth utilization, use the show controllers utilization command in EXEC mode.
show controllers [ interface-id ] utilization
None
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This is an example of output from the show controllers utilization command:
Switch> show controllers utilization Port Receive Utilization Transmit Utilization Gi1/0/1 0 0 Gi1/0/2 0 0 Gi1/0/3 0 0 Gi1/0/4 0 0 Gi1/0/5 0 0 Gi1/0/6 0 0 Gi1/0/7 0 0 <output truncated> Gi2/0/1 0 0 Gi2/0/2 0 0 <output truncated> Switch Receive Bandwidth Percentage Utilization : 0 Switch Transmit Bandwidth Percentage Utilization : 0 Switch Fabric Percentage Utilization : 0
This is an example of output from the show controllers utilization command on a specific port:
Switch> show controllers gigabitethernet1/0/1 utilization Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0
To display fan, temperature, and power information, use the show env command in EXEC mode.
show env { all | fan | power [ all | switch [ stack-member-number ] ] | stack [ stack-member-number ] | temperature [ status ] }
all |
Displays the fan and temperature environmental status and the status of the internal power supplies. |
fan |
Displays the switch fan status. |
power |
Displays the internal power status of the active switch. |
all |
(Optional) Displays the status of all the internal power supplies in a standalone switch when the command is entered on the switch, or in all the stack members when the command is entered on the active switch. |
switch |
(Optional) Displays the status of the internal power supplies for each switch in the stack or for the specified switch. This keyword is available only on stacking-capable switches. |
stack-member-number |
(Optional) Number of the stack member for which to display the status of the internal power supplies or the environmental status. The range is 1 to 9. |
stack |
Displays all environmental status for each switch in the stack or for the specified switch. This keyword is available only on stacking-capable switches. |
temperature |
Displays the switch temperature status. |
status |
(Optional) Displays the switch internal temperature (not the external temperature) and the threshold values. |
None
User EXEC
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
Use the show env EXEC command to display the information for the switch being accessed—a standalone switch or the active switch. Use this command with the stack and switch keywords to display all information for the stack or for the specified stack member.
If you enter the show env temperature status command, the command output shows the switch temperature state and the threshold level.
You can also use the show env temperature command to display the switch temperature status. The command output shows the green and yellow states as OK and the red state as FAULTY. If you enter the show env all command, the command output is the same as the show env temperature status command output.
This is an example of output from the show env all command:
Switch>show env all
Switch 1 FAN 1 is OK
Switch 1 FAN 2 is OK
Switch 1 FAN 3 is OK
FAN PS-1 is OK
FAN PS-2 is NOT PRESENT
Switch 1: SYSTEM TEMPERATURE is OK
SW PID Serial# Status Sys Pwr PoE Pwr Watts
-- ------------------ ---------- --------------- ------- ------- -----
1A PWR-C2-250WAC LIT16372A1M OK Good Good 250
1B Not Present
This is an example of output from the show env fan command:
Switch>show env fan
Switch 1 FAN 1 is OK
Switch 1 FAN 2 is OK
Switch 1 FAN 3 is OK
FAN PS-1 is NOT PRESENT
FAN PS-2 is OK
This is an example of output from the show env power all command on the active switch:
Switch# show env power all
SW PID Serial# Status Sys Pwr PoE Pwr Watts
-- ------------------ ---------- --------------- ------- ------- -----
1A PWR-C2-250WAC LIT16372A1M OK Good Good 250
1B Not Present
This is an example of output from the show env stack command on the active switch:
Switch> show env stack
SWITCH: 1
Switch 1 FAN 1 is OK
Switch 1 FAN 2 is OK
Switch 1 FAN 3 is OK
FAN PS-1 is NOT PRESENT
FAN PS-2 is OK
Switch 1: SYSTEM TEMPERATURE is OK
Temperature Value: 28 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 41 Degree Celsius
Red Threshold : 56 Degree Celsius
This example shows how to display the temperature value, state, and the threshold values on a standalone switch. The table describes the temperature states in the command output.
Switch> show env temperature status
Temperature Value: 33 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 65 Degree Celsius
Red Threshold : 75 Degree Celsius
State |
Description |
---|---|
Green |
The switch temperature is in the normal operating range. |
Yellow |
The temperature is in the warning range. You should check the external temperature around the switch. |
Red |
The temperature is in the critical range. The switch might not run properly if the temperature is in this range. |
To display error-disabled detection status, use the show errdisable detect command in EXEC mode.
show errdisable detect
None
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
A gbic-invalid error reason refers to an invalid small form-factor pluggable (SFP) module.
The error-disable reasons in the command output are listed in alphabetical order. The mode column shows how error-disable is configured for each feature.
This is an example of output from the show errdisable detect command:
To display the error-disabled recovery timer information, use the show errdisable recovery command in EXEC mode.
show errdisable recovery
None
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
A gbic-invalid error-disable reason refers to an invalid small form-factor pluggable (SFP) module interface.
![]() Note | Though visible in the output, the unicast-flood field is not valid. |
This is an example of output from the show errdisable recovery command:
To display the administrative and operational status of all interfaces or for a specified interface, use the show interfaces command in privileged EXEC mode.
show interfaces [ interface-id | vlan vlan-id ] [ accounting | capabilities [ module number ] | debounce | description | etherchannel | flowcontrol | private-vlan mapping | pruning | stats | status [ err-disabled ] | trunk ]
interface-id |
(Optional) ID of the interface. Valid interfaces include physical ports (including type, stack member for stacking-capable switches, module, and port number) and port channels. The port channel range is 1 to 48. |
||
vlan vlan-id |
(Optional) VLAN identification. The range is 1 to 4094. |
||
accounting |
(Optional) Displays accounting information on the interface, including active protocols and input and output packets and octets.
|
||
capabilities |
(Optional) Displays the capabilities of all interfaces or the specified interface, including the features and options that you can configure on the interface. Though visible in the command line help, this option is not available for VLAN IDs. |
||
module number |
(Optional) Displays capabilities of all interfaces on the switch or specified stack member. This option is not available if you entered a specific interface ID. |
||
description |
(Optional) Displays the administrative status and description set for an interface. |
||
etherchannel |
(Optional) Displays interface EtherChannel information. |
||
flowcontrol |
(Optional) Displays interface flow control information. |
||
private-vlan mapping |
(Optional) Displays private-VLAN mapping information for the VLAN switch virtual interfaces (SVIs). This keyword is not available if the switch is running the LAN base feature set. |
||
pruning |
(Optional) Displays trunk VTP pruning information for the interface. |
||
stats |
(Optional) Displays the input and output packets by switching the path for the interface. |
||
status |
(Optional) Displays the status of the interface. A status of unsupported in the Type field means that a non-Cisco small form-factor pluggable (SFP) module is inserted in the module slot. |
||
err-disabled |
(Optional) Displays interfaces in an error-disabled state. |
||
trunk |
(Optional) Displays interface trunk information. If you do not specify an interface, only information for active trunking ports appears. |
![]() Note | Though visible in the command-line help strings, the crb, fair-queue, irb, mac-accounting, precedence, random-detect, rate-limit, and shape keywords are not supported. |
None
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
Use the show interface capabilities module number command to display the capabilities of all interfaces on that switch in the stack. If there is no switch with that module number in the stack, there is no output.
Use the show interfaces interface-id capabilities to display the capabilities of the specified interface.
Use the show interfaces capabilities (with no module number or interface ID) to display the capabilities of all interfaces in the stack.
This is an example of output from the show interfaces command for an interface on stack member 3:
Switch# show interfaces gigabitethernet3/0/2
GigabitEthernet3/0/2 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 2037.064d.4381 (bia 2037.064d.4381)
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
This is an example of output from the show interfaces accounting command:
This is an example of output from the show interfaces capabilities command for an interface:
This is an example of output from the show interfaces interface description command when the interface has been described as Connects to Marketing by using the description interface configuration command:
Switch# show interfaces gigabitethernet1/0/2 description
Interface Status Protocol Description
Gi1/0/2 up down Connects to Marketing
This is an example of output from the show interfaces etherchannel command when port channels are configured on the switch:
Switch# show interfaces etherchannel
----
Port-channel34:
Age of the Port-channel = 28d:18h:51m:46s
Logical slot/port = 12/34 Number of ports = 0
GC = 0x00000000 HotStandBy port = null
Passive port list =
Port state = Port-channel L3-Ag Ag-Not-Inuse
Protocol = -
Port security = Disabled
This is an example of output from the show interfaces interface-id pruning command when pruning is enabled in the VTP domain:
Switch# show interfaces gigabitethernet1/0/2 pruning
Port Vlans pruned for lack of request by neighbor
Gi1/0/2 3,4
Port Vlans traffic requested of neighbor
Gi1/0/2 1-3
This is an example of output from the show interfaces stats command for a specified VLAN interface:
Switch# show interfaces vlan 1 stats
Switching path Pkts In Chars In Pkts Out Chars Out
Processor 1165354 136205310 570800 91731594
Route cache 0 0 0 0
Total 1165354 136205310 570800 91731594
This is an example of partial output from the show interfaces status command. It displays the status of all interfaces:
These are examples of output from the show interfaces status command for a specific interface when private VLANs are configured. Port 22 is configured as a private-VLAN host port. It is associated with primary VLAN 20 and secondary VLAN 25:
Switch# show interfaces gigabitethernet1/0/22 status
Port Name Status Vlan Duplex Speed Type
Gi1/0/22 connected 20,25 a-full a-100 10/100BaseTX
In this example, port 20 is configured as a private-VLAN promiscuous port. The display shows only the primary VLAN 20:
Switch# show interfaces gigabitethernet1/0/20 status
Port Name Status Vlan Duplex Speed Type
Gi1/0/20 connected 20 a-full a-100 10/100BaseTX
This is an example of output from the show interfaces status err-disabled command. It displays the status of interfaces in the error-disabled state:
Switch# show interfaces status err-disabled
Port Name Status Reason
Gi1/0/2 err-disabled gbic-invalid
Gi2/0/3 err-disabled dtp-flap
This is an example of output from the show interfaces interface-id pruning command:
Switch# show interfaces gigabitethernet1/0/2 pruning
Port Vlans pruned for lack of request by neighbor
This is an example of output from the show interfaces interface-id trunk command. It displays trunking information for the port.
Switch# show interfaces gigabitethernet1/0/1 trunk
Port Mode Encapsulation Status Native vlan
Gi1/0/1 on 802.1q other 10
Port Vlans allowed on trunk
Gi1/0/1 none
Port Vlans allowed and active in management domain
Gi1/0/1 none
Port Vlans in spanning tree forwarding state and not pruned
Gi1/0/1 none
To display various counters for the switch or for a specific interface, use the show interfaces counters command in privileged EXEC mode.
show interfaces [ interface-id ] counters [ errors | etherchannel | module stack-member-number | protocol status | trunk ]
interface-id |
(Optional) ID of the physical interface, including type, stack member (stacking-capable switches only) module, and port number. |
||
errors |
(Optional) Displays error counters. |
||
etherchannel |
(Optional) Displays EtherChannel counters, including octets, broadcast packets, multicast packets, and unicast packets received and sent. |
||
module stack-member-number |
(Optional) Displays counters for the specified stack member.
|
||
protocol status |
(Optional) Displays the status of protocols enabled on interfaces. |
||
trunk |
(Optional) Displays trunk counters. |
![]() Note | Though visible in the command-line help string, the vlan vlan-id keyword is not supported. |
None
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
If you do not enter any keywords, all counters for all interfaces are included.
This is an example of partial output from the show interfaces counters command. It displays all counters for the switch.
Switch# show interfaces counters
Port InOctets InUcastPkts InMcastPkts InBcastPkts
Gi1/0/1 0 0 0 0
Gi1/0/2 0 0 0 0
Gi1/0/3 95285341 43115 1178430 1950
Gi1/0/4 0 0 0 0
<output truncated>
This is an example of partial output from the show interfaces counters module command for stack member 2. It displays all counters for the specified switch in the stack.
Switch# show interfaces counters module 2
Port InOctets InUcastPkts InMcastPkts InBcastPkts
Gi1/0/1 520 2 0 0
Gi1/0/2 520 2 0 0
Gi1/0/3 520 2 0 0
Gi1/0/4 520 2 0 0
<output truncated>
This is an example of partial output from the show interfaces counters protocol status command for all interfaces:
Switch# show interfaces counters protocol status
Protocols allocated:
Vlan1: Other, IP
Vlan20: Other, IP, ARP
Vlan30: Other, IP, ARP
Vlan40: Other, IP, ARP
Vlan50: Other, IP, ARP
Vlan60: Other, IP, ARP
Vlan70: Other, IP, ARP
Vlan80: Other, IP, ARP
Vlan90: Other, IP, ARP
Vlan900: Other, IP, ARP
Vlan3000: Other, IP
Vlan3500: Other, IP
GigabitEthernet1/0/1: Other, IP, ARP, CDP
GigabitEthernet1/0/2: Other, IP
GigabitEthernet1/0/3: Other, IP
GigabitEthernet1/0/4: Other, IP
GigabitEthernet1/0/5: Other, IP
GigabitEthernet1/0/6: Other, IP
GigabitEthernet1/0/7: Other, IP
GigabitEthernet1/0/8: Other, IP
GigabitEthernet1/0/9: Other, IP
GigabitEthernet1/0/10: Other, IP, CDP
<output truncated>
This is an example of output from the show interfaces counters trunk command. It displays trunk counters for all interfaces.
Switch# show interfaces counters trunk
Port TrunkFramesTx TrunkFramesRx WrongEncap
Gi1/0/1 0 0 0
Gi1/0/2 0 0 0
Gi1/0/3 80678 0 0
Gi1/0/4 82320 0 0
Gi1/0/5 0 0 0
<output truncated>
To display the administrative and operational status of a switching (nonrouting) port, including port blocking and port protection settings, use the show interfaces switchport command in privileged EXEC mode.
show interfaces [ interface-id ] switchport [ backup [ detail ] | module number ]
interface-id |
(Optional) ID of the interface. Valid interfaces include physical ports (including type, stack member for stacking-capable switches, module, and port number) and port channels. The port channel range is 1 to 48. |
backup |
(Optional) Displays Flex Link backup interface configuration for the specified interface or all interfaces. |
detail |
(Optional) Displays detailed backup information for the specified interface or all interfaces on the switch or the stack. |
module number |
(Optional) Displays switchport configuration of all interfaces on the switch or specified stack member. This option is not available if you entered a specific interface ID. |
None
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
Use the show interface switchport module number command to display the switch port characteristics of all interfaces on that switch in the stack. If there is no switch with that module number in the stack, there is no output.
![]() Note | Private VLANs are not supported in this release, so those fields are not applicable. |
Switch# show interfaces gigabitethernet1/0/1 switchport
Name: Gi1/0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: down
Administrative Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 10 (VLAN0010)
Administrative Native VLAN tagging: enabled
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk associations: none
Administrative private-vlan trunk mappings: none
Operational private-vlan: none
Trunking VLANs Enabled: 11-20
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none
Field |
Description |
---|---|
Name |
Displays the port name. |
Switchport |
Displays the administrative and operational status of the port. In this display, the port is in switchport mode. |
Administrative Mode Operational Mode |
Displays the administrative and operational modes. |
Administrative Trunking Encapsulation Operational Trunking Encapsulation Negotiation of Trunking |
Displays the administrative and operational encapsulation method and whether trunking negotiation is enabled. |
Access Mode VLAN |
Displays the VLAN ID to which the port is configured. |
Trunking Native Mode VLAN Trunking VLANs Enabled Trunking VLANs Active |
Lists the VLAN ID of the trunk that is in native mode. Lists the allowed VLANs on the trunk. Lists the active VLANs on the trunk. |
Pruning VLANs Enabled |
Lists the VLANs that are pruning-eligible. |
Protected |
Displays whether or not protected port is enabled (True) or disabled (False) on the interface. |
Unknown unicast blocked Unknown multicast blocked |
Displays whether or not unknown multicast and unknown unicast traffic is blocked on the interface. |
Voice VLAN |
Displays the VLAN ID on which voice VLAN is enabled. |
Appliance trust |
Displays the class of service (CoS) setting of the data packets of the IP phone. |
This is an example of output from the show interfaces switchport backup command:
Switch# show interfaces switchport backup Switch Backup Interface Pairs: Active Interface Backup Interface State -------------------------------------------------------------- Gi1/0/1 Gi1/0/2 Active Up/Backup Standby Gi3/0/3 Gi4/0/5 Active Down/Backup Up Po1 Po2 Active Standby/Backup Up
In this example of output from the show interfaces switchport backup command, VLANs 1 to 50, 60, and 100 to 120 are configured on the switch:
Switch(config)# interface gigabitethernet 2/0/6 Switch(config-if)# switchport backup interface gigabitethernet 2/0/8 prefer vlan 60,100-120
When both interfaces are up, Gi2/0/8 forwards traffic for VLANs 60, 100 to 120, and Gi2/0/6 will forward traffic for VLANs 1 to 50.
Switch# show interfaces switchport backup Switch Backup Interface Pairs: Active Interface Backup Interface State ------------------------------------------------------------------------ GigabitEthernet2/0/6 GigabitEthernet2/0/8 Active Up/Backup Up Vlans on Interface Gi 2/0/6: 1-50 Vlans on Interface Gi 2/0/8: 60, 100-120
When a Flex Link interface goes down (LINK_DOWN), VLANs preferred on this interface are moved to the peer interface of the Flex Link pair. In this example, if interface Gi2/0/6 goes down, Gi2/0/8 carries all VLANs of the Flex Link pair.
Switch# show interfaces switchport backup Switch Backup Interface Pairs: Active Interface Backup Interface State ------------------------------------------------------------------------ GigabitEthernet2/0/6 GigabitEthernet2/0/8 Active Down/Backup Up Vlans on Interface Gi 2/0/6: Vlans on Interface Gi 2/0/8: 1-50, 60, 100-120
When a Flex Link interface comes up, VLANs preferred on this interface are blocked on the peer interface and moved to the forwarding state on the interface that has just come up. In this example, if interface Gi2/0/6 comes up, then VLANs preferred on this interface are blocked on the peer interface Gi2/0/8 and forwarded on Gi2/0/6.
Switch# show interfaces switchport backup Switch Backup Interface Pairs: Active Interface Backup Interface State ------------------------------------------------------------------------ GigabitEthernet2/0/6 GigabitEthernet2/0/8 Active Up/Backup Up Vlans on Interface Gi 2/0/6: 1-50 Vlans on Interface Gi 2/0/8: 60, 100-120
To display the physical properties of a small form-factor pluggable (SFP) module interface, use the show interfaces transceiver command in EXEC mode.
show interfaces [ interface-id ] transceiver [ detail | module number | properties | supported-list | threshold-table ]
interface-id |
(Optional) ID of the physical interface, including type, stack member (stacking-capable switches only) module, and port number. |
detail |
(Optional) Displays calibration properties, including high and low numbers and any alarm information for any Digital Optical Monitoring (DoM)-capable transceiver if one is installed in the switch. |
module number |
(Optional) Limits display to interfaces on module on the switch. The range is 1 to 9. This option is not available if you entered a specific interface ID. |
properties |
(Optional) Displays speed, duplex, and inline power settings on an interface. |
supported-list |
(Optional) Lists all supported transceivers. |
threshold-table |
(Optional) Displays alarm and warning threshold table. |
User EXEC
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This is an example of output from the show interfaces interface-id transceiver properties command:
This is an example of output from the show interfaces interface-id transceiver detail command:
Switch# show interfaces gigabitethernet1/1/1 transceiver detail
ITU Channel not available (Wavelength not available),
Transceiver is internally calibrated.
mA:milliamperes, dBm:decibels (milliwatts), N/A:not applicable.
++:high alarm, +:high warning, -:low warning, -- :low alarm.
A2D readouts (if they differ), are reported in parentheses.
The threshold values are uncalibrated.
High Alarm High Warn Low Warn Low Alarm
Temperature Threshold Threshold Threshold Threshold
Port (Celsius) (Celsius) (Celsius) (Celsius) (Celsius)
------- ----------------- ---------- --------- --------- ---------
Gi1/1/1 29.9 74.0 70.0 0.0 -4.0
High Alarm High Warn Low Warn Low Alarm
Voltage Threshold Threshold Threshold Threshold
Port (Volts) (Volts) (Volts) (Volts) (Volts)
------- --------------- ---------- --------- --------- ---------
Gi1/1/1 3.28 3.60 3.50 3.10 3.00
Optical High Alarm High Warn Low Warn Low Alarm
Transmit Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
------- ----------------- ---------- --------- --------- ---------
Gi1/1/1 1.8 7.9 3.9 0.0 -4.0
Optical High Alarm High Warn Low Warn Low Alarm
Receive Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
------- ----------------- ---------- --------- --------- ---------
Gi1/1/1 -23.5 -5.0 -9.0 -28.2 -32.2
This is an example of output from the show interfaces transceiver threshold-table command:
Switch# show interfaces transceiver threshold-table
Optical Tx Optical Rx Temp Laser Bias Voltage
current
------------- ------------- ------ ------------ ---------
DWDM GBIC
Min1 -4.00 -32.00 -4 N/A 4.65
Min2 0.00 -28.00 0 N/A 4.75
Max2 4.00 -9.00 70 N/A 5.25
Max1 7.00 -5.00 74 N/A 5.40
DWDM SFP
Min1 -4.00 -32.00 -4 N/A 3.00
Min2 0.00 -28.00 0 N/A 3.10
Max2 4.00 -9.00 70 N/A 3.50
Max1 8.00 -5.00 74 N/A 3.60
RX only WDM GBIC
Min1 N/A -32.00 -4 N/A 4.65
Min2 N/A -28.30 0 N/A 4.75
Max2 N/A -9.00 70 N/A 5.25
Max1 N/A -5.00 74 N/A 5.40
DWDM XENPAK
Min1 -5.00 -28.00 -4 N/A N/A
Min2 -1.00 -24.00 0 N/A N/A
Max2 3.00 -7.00 70 N/A N/A
Max1 7.00 -3.00 74 N/A N/A
DWDM X2
Min1 -5.00 -28.00 -4 N/A N/A
Min2 -1.00 -24.00 0 N/A N/A
Max2 3.00 -7.00 70 N/A N/A
Max1 7.00 -3.00 74 N/A N/A
DWDM XFP
Min1 -5.00 -28.00 -4 N/A N/A
Min2 -1.00 -24.00 0 N/A N/A
Max2 3.00 -7.00 70 N/A N/A
Max1 7.00 -3.00 74 N/A N/A
CWDM X2
Min1 N/A N/A 0 N/A N/A
Min2 N/A N/A 0 N/A N/A
Max2 N/A N/A 0 N/A N/A
Max1 N/A N/A 0 N/A N/A
<output truncated>
To display inline power messages within a trace buffer, use the show mgmt-infra trace messages ilpower command in privileged EXEC mode.
show mgmt-infra trace messages ilpower [ switch stack-member-number ]
switch stack-member-number |
(Optional) Specifies the stack member number for which to display inline power messages within a trace buffer. |
None
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This is an output example from the show mgmt-infra trace messages ilpower command:
Switch# show mgmt-infra trace messages ilpower
[10/23/12 14:05:10.984 UTC 1 3] Initialized inline power system configuration fo
r slot 1.
[10/23/12 14:05:10.984 UTC 2 3] Initialized inline power system configuration fo
r slot 2.
[10/23/12 14:05:10.984 UTC 3 3] Initialized inline power system configuration fo
r slot 3.
[10/23/12 14:05:10.984 UTC 4 3] Initialized inline power system configuration fo
r slot 4.
[10/23/12 14:05:10.984 UTC 5 3] Initialized inline power system configuration fo
r slot 5.
[10/23/12 14:05:10.984 UTC 6 3] Initialized inline power system configuration fo
r slot 6.
[10/23/12 14:05:10.984 UTC 7 3] Initialized inline power system configuration fo
r slot 7.
[10/23/12 14:05:10.984 UTC 8 3] Initialized inline power system configuration fo
r slot 8.
[10/23/12 14:05:10.984 UTC 9 3] Initialized inline power system configuration fo
r slot 9.
[10/23/12 14:05:10.984 UTC a 3] Inline power subsystem initialized.
[10/23/12 14:05:18.908 UTC b 264] Create new power pool for slot 1
[10/23/12 14:05:18.909 UTC c 264] Set total inline power to 450 for slot 1
[10/23/12 14:05:20.273 UTC d 3] PoE is not supported on .
[10/23/12 14:05:20.288 UTC e 3] PoE is not supported on .
[10/23/12 14:05:20.299 UTC f 3] PoE is not supported on .
[10/23/12 14:05:20.311 UTC 10 3] PoE is not supported on .
[10/23/12 14:05:20.373 UTC 11 98] Inline power process post for switch 1
[10/23/12 14:05:20.373 UTC 12 98] PoE post passed on switch 1
[10/23/12 14:05:20.379 UTC 13 3] Slot #1: PoE initialization for board id 16387
[10/23/12 14:05:20.379 UTC 14 3] Set total inline power to 450 for slot 1
[10/23/12 14:05:20.379 UTC 15 3] Gi1/0/1 port config Initialized
[10/23/12 14:05:20.379 UTC 16 3] Interface Gi1/0/1 initialization done.
[10/23/12 14:05:20.380 UTC 17 3] Gi1/0/24 port config Initialized
[10/23/12 14:05:20.380 UTC 18 3] Interface Gi1/0/24 initialization done.
[10/23/12 14:05:20.380 UTC 19 3] Slot #1: initialization done.
[10/23/12 14:05:50.440 UTC 1a 3] Slot #1: PoE initialization for board id 16387
[10/23/12 14:05:50.440 UTC 1b 3] Duplicate init event
To display inline power high availability messages within a trace buffer, use the show mgmt-infra trace messages ilpower-ha command in privileged EXEC mode.
show mgmt-infra trace messages ilpower-ha [ switch stack-member-number ]
switch stack-member-number |
(Optional) Specifies the stack member number for which to display inline power messages within a trace buffer. |
None
Privileged EXEC
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This is an output example from the show mgmt-infra trace messages ilpower-ha command:
Switch# show mgmt-infra trace messages ilpower-ha
[10/23/12 14:04:48.087 UTC 1 3] NG3K_ILPOWER_HA: Created NGWC ILP CF client succ
essfully.
To display platform manager Power over Ethernet (PoE) messages within a trace buffer, use the show mgmt-infra trace messages platform-mgr-poe privileged EXEC command.
show mgmt-infra trace messages platform-mgr-poe [ switch stack-member-number ]
switch stack-member-number |
(Optional) Specifies the stack member number for which to display messages within a trace buffer. |
None
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This is an example of partial output from the show mgmt-infra trace messages platform-mgr-poe command:
Switch# show mgmt-infra trace messages platform-mgr-poe
[10/23/12 14:04:06.431 UTC 1 5495] PoE Info: get power controller param sent:
[10/23/12 14:04:06.431 UTC 2 5495] PoE Info: POE_SHUT sent for port 1 (0:0)
[10/23/12 14:04:06.431 UTC 3 5495] PoE Info: POE_SHUT sent for port 2 (0:1)
[10/23/12 14:04:06.431 UTC 4 5495] PoE Info: POE_SHUT sent for port 3 (0:2)
[10/23/12 14:04:06.431 UTC 5 5495] PoE Info: POE_SHUT sent for port 4 (0:3)
[10/23/12 14:04:06.431 UTC 6 5495] PoE Info: POE_SHUT sent for port 5 (0:4)
[10/23/12 14:04:06.431 UTC 7 5495] PoE Info: POE_SHUT sent for port 6 (0:5)
[10/23/12 14:04:06.431 UTC 8 5495] PoE Info: POE_SHUT sent for port 7 (0:6)
[10/23/12 14:04:06.431 UTC 9 5495] PoE Info: POE_SHUT sent for port 8 (0:7)
[10/23/12 14:04:06.431 UTC a 5495] PoE Info: POE_SHUT sent for port 9 (0:8)
[10/23/12 14:04:06.431 UTC b 5495] PoE Info: POE_SHUT sent for port 10 (0:9)
[10/23/12 14:04:06.431 UTC c 5495] PoE Info: POE_SHUT sent for port 11 (0:10)
[10/23/12 14:04:06.431 UTC d 5495] PoE Info: POE_SHUT sent for port 12 (0:11)
[10/23/12 14:04:06.431 UTC e 5495] PoE Info: POE_SHUT sent for port 13 (e:0)
[10/23/12 14:04:06.431 UTC f 5495] PoE Info: POE_SHUT sent for port 14 (e:1)
[10/23/12 14:04:06.431 UTC 10 5495] PoE Info: POE_SHUT sent for port 15 (e:2)
[10/23/12 14:04:06.431 UTC 11 5495] PoE Info: POE_SHUT sent for port 16 (e:3)
[10/23/12 14:04:06.431 UTC 12 5495] PoE Info: POE_SHUT sent for port 17 (e:4)
[10/23/12 14:04:06.431 UTC 13 5495] PoE Info: POE_SHUT sent for port 18 (e:5)
[10/23/12 14:04:06.431 UTC 14 5495] PoE Info: POE_SHUT sent for port 19 (e:6)
[10/23/12 14:04:06.431 UTC 15 5495] PoE Info: POE_SHUT sent for port 20 (e:7)
[10/23/12 14:04:06.431 UTC 16 5495] PoE Info: POE_SHUT sent for port 21 (e:8)
[10/23/12 14:04:06.431 UTC 17 5495] PoE Info: POE_SHUT sent for port 22 (e:9)
[10/23/12 14:04:06.431 UTC 18 5495] PoE Info: POE_SHUT sent for port 23 (e:10)
To display the network-policy profiles, use the show network policy profile command in privileged EXEC mode.
show network-policy profile [ profile-number ] [ detail ]
profile-number |
(Optional) Displays the network-policy profile number. If no profile is entered, all network-policy profiles appear. |
detail |
(Optional) Displays detailed status and statistics information. |
None
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This is an example of output from the show network-policy profile command:
Switch# show network-policy profile
Network Policy Profile 10
voice vlan 17 cos 4
Interface:
none
Network Policy Profile 30
voice vlan 30 cos 5
Interface:
none
Network Policy Profile 36
voice vlan 4 cos 3
Interface:
Interface_id
To display the tunnel identifier and the type all the CAPWAP tunnels established by the controller to the access points and other mobility controllers, use the show platform CAPWAP summary command.
show platform CAPWAP summary
This command has no arguments or keywords.
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This example displays the tunnel identifier and details:
Switch# show platform capwap summary
Tunnel ID | Type | Src IP | Dst IP | SPrt | DPrt | S | A
-------------------------------------------------------------------------------
0x0088498000000983 data 9.6.44.61 9.12.138.101 5247 41894 1 1
0x00966dc000000010 data 9.6.44.61 9.6.47.101 5247 62526 1 2
0x00938e800000095b data 9.6.44.61 9.12.138.100 5247 45697 1 1
0x00ab1a8000000bd1 data 9.6.44.61 9.12.139.101 5247 38906 1 0
0x00896e40000000bd data 9.6.44.61 9.12.136.100 5247 1836 1 1
To display the Power over Ethernet (PoE) status for the specified PoE port, the specified stack member, or for all PoE ports in the switch stack, use the show power inline command in EXEC mode.
show power inline [ police | priority ] [ interface-id | module stack-member-number ] [detail]
police |
(Optional) Displays the power policing information about real-time power consumption. |
priority |
(Optional) Displays the power inline port priority for each port. |
interface-id |
(Optional) ID of the physical interface. |
module stack-member-number |
(Optional) Limits the display to ports on the specified stack member. This keyword is supported only on stacking-capable switches. |
detail |
(Optional) Displays detailed output of the interface or module. |
User EXEC
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This is an example of output from the show power inline command. The table that follows describes the output fields.
Switch> show power inline
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 n/a n/a n/a
2 n/a n/a n/a
3 1440.0 15.4 1424.6
4 720.0 6.3 713.7
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi3/0/1 auto off 0.0 n/a n/a 30.0
Gi3/0/2 auto off 0.0 n/a n/a 30.0
Gi3/0/3 auto off 0.0 n/a n/a 30.0
Gi3/0/4 auto off 0.0 n/a n/a 30.0
Gi3/0/5 auto off 0.0 n/a n/a 30.0
Gi3/0/6 auto off 0.0 n/a n/a 30.0
Gi3/0/7 auto off 0.0 n/a n/a 30.0
Gi3/0/8 auto off 0.0 n/a n/a 30.0
Gi3/0/9 auto off 0.0 n/a n/a 30.0
Gi3/0/10 auto off 0.0 n/a n/a 30.0
Gi3/0/11 auto off 0.0 n/a n/a 30.0
Gi3/0/12 auto off 0.0 n/a n/a 30.0
<output truncated>
This is an example of output from the show power inline interface-id command on a switch port:
Switch> show power inline gigabitethernet1/0/1
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi1/0/1 auto off 0.0 n/a n/a 30.0
This is an example of output from the show power inline module switch-number command on stack member 3. The table that follows describes the output fields.
Switch> show power inline module 3
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
3 865.0 864.0 1.0
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi3/0/1 auto power-deny 4.0 n/a n/a 15.4
Gi3/0/2 auto off 0.0 n/a n/a 15.4
Gi3/0/3 auto off 0.0 n/a n/a 15.4
Gi3/0/4 auto off 0.0 n/a n/a 15.4
Gi3/0/5 auto off 0.0 n/a n/a 15.4
Gi3/0/6 auto off 0.0 n/a n/a 15.4
Gi3/0/7 auto off 0.0 n/a n/a 15.4
Gi3/0/8 auto off 0.0 n/a n/a 15.4
Gi3/0/9 auto off 0.0 n/a n/a 15.4
Gi3/0/10 auto off 0.0 n/a n/a 15.4
<output truncated>
Field |
Description |
---|---|
Available |
The total amount of configured power4 on the PoE switch in watts (W). |
Used |
The amount of configured power that is allocated to PoE ports in watts. |
Remaining |
The amount of configured power in watts that is not allocated to ports in the system. (Available – Used = Remaining) |
Admin |
Administration mode: auto, off, static. |
Oper |
Operating mode: |
Power |
The maximum amount of power that is allocated to the powered device in watts. This value is the same as the value in the Cutoff Power field in the show power inline police command output. |
Device |
The device type detected: n/a, unknown, Cisco powered-device, IEEE powered-device, or the name from CDP. |
Class |
The IEEE classification: n/a or a value from 0 to 4. |
Max |
The maximum amount of power allocated to the powered device in watts. |
AdminPowerMax |
The maximum amount power allocated to the powered device in watts when the switch polices the real-time power consumption. This value is the same as the Max field value. |
AdminConsumption |
The power consumption of the powered device in watts when the switch polices the real-time power consumption. If policing is disabled, this value is the same as the AdminPowerMax field value. |
This is an example of output from the show power inline police command on a stacking-capable switch:
Switch> show power inline police
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 370.0 0.0 370.0
3 865.0 864.0 1.0
Admin Oper Admin Oper Cutoff Oper
Interface State State Police Police Power Power
--------- ------ ----------- ---------- ---------- ------ ------
Gi1/0/1 auto off none n/a n/a 0.0
Gi1/0/2 auto off log n/a 5.4 0.0
Gi1/0/3 auto off errdisable n/a 5.4 0.0
Gi1/0/4 off off none n/a n/a 0.0
Gi1/0/5 off off log n/a 5.4 0.0
Gi1/0/6 off off errdisable n/a 5.4 0.0
Gi1/0/7 auto off none n/a n/a 0.0
Gi1/0/8 auto off log n/a 5.4 0.0
Gi1/0/9 auto on none n/a n/a 5.1
Gi1/0/10 auto on log ok 5.4 4.2
Gi1/0/11 auto on log log 5.4 5.9
Gi1/0/12 auto on errdisable ok 5.4 4.2
Gi1/0/13 auto errdisable errdisable n/a 5.4 0.0
<output truncated>
In the previous example:
This is an example of output from the show power inline police interface-id command on a standalone switch. The table that follows describes the output fields.
Switch> show power inline police gigabitethernet1/0/1
Interface Admin Oper Admin Oper Cutoff Oper
State State Police Police Power Power
--------- ------ ---------- ---------- ---------- ------ -----
Gi1/0/1 auto off none n/a n/a 0.0
Field |
Description |
||
---|---|---|---|
Available |
The total amount of configured power5 on the switch in watts (W). |
||
Used |
The amount of configured power allocated to PoE ports in watts. |
||
Remaining |
The amount of configured power in watts that is not allocated to ports in the system. (Available – Used = Remaining) |
||
Admin State |
Administration mode: auto, off, static. |
||
Oper State |
Operating mode:
|
||
Admin Police |
Status of the real-time power-consumption policing feature:
|
||
Oper Police |
Policing status:
|
||
Cutoff Power |
The maximum power allocated on the port. When the real-time power consumption is greater than this value, the switch takes the configured policing action. |
||
Oper Power |
The real-time power consumption of the powered device. |
To display the global maximum transmission unit (MTU) or maximum packet size set for the switch, use the show system mtu command in privileged EXEC mode.
show system mtu
This command has no arguments or keywords.
None
Privileged EXEC
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
For information about the MTU values and the stack configurations that affect the MTU values, see the system mtu command.
This is an example of output from the show system mtu command:
Switch# show system mtu
Global Ethernet MTU is 1500 bytes.
To display the wireless interface status and configuration, use the show wireless interface summary privileged EXEC command.
show wireless interface summary
None
Privileged EXEC
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to display the summary of wireless interfaces:
Switch# show wireless interface summary
To configure the rate (threshold) for an interface to be error-disabled when it receives VLAN-tagged packets that are small frames (67 bytes or less), use the small-frame violation rate interface configuration command. Use the no form of this command to return to the default setting.
small-frame violation rate pps
no small-frame violation rate pps
Specifies the threshold at which an interface receiving small frames will be error-disabled. The range is 1 to 10,000 packets per second (pps). |
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This command enables the rate (threshold) for a port to be error-disabled when it receives small frames. Small frames are considered packets that are 67 frames or less.
Use the errdisable detect cause small-frame global configuration command to globally enable the small-frames threshold for each port.
You can configure the port to be automatically reenabled by using the errdisable recovery cause small-frame global configuration command. You configure the recovery time by using the errdisable recovery interval interval global configuration command.
This example shows how to enable the small-frame arrival rate feature so that the port is error-disabled if incoming small frames arrived at 10,000 pps:
Switch(config)# interface gigabitethernet2/0/1 Switch(config-if)# small-frame violation rate 10000
To specify the speed of a 10/100/1000/2500/5000 Mb/s port, use the speed command in interface configuration mode. To return to the default value, use the no form of this command.
speed { 10 | 100 | 1000 | 2500 | 5000 | auto [ 10 | 100 | 1000 | 2500 | 5000 ] | nonegotiate }
no speed
10 |
Specifies that the port runs at 10 Mb/s. |
100 |
Specifies that the port runs at 100 Mb/s. |
1000 |
Specifies that the port runs at 1000 Mb/s. This option is valid and visible only on 10/100/1000 Mb/s ports. |
2500 |
Specifies that the port runs at 2500 Mb/s. This option is valid and visible only on mGig supported Ethernet ports. |
5000 |
Specifies that the port runs at 5000 Mb/s. This option is valid and visible only on mGig supported Ethernet ports. |
auto |
Automatically detects the speed the port should run at based on the port at the other end of the link. If you use the 10, 100, 1000, 1000, 2500, 5000 keywords with the auto keyword, the port only autonegotiates at the specified speeds. |
nonegotiate |
Disables autonegotiation, and the port runs at 1000 Mb/s. |
The default is auto.
Interface configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
Cisco IOS XE Denali 16.3.1 |
This command was modified. The following keywords were added: 2500, and 5000. These keywords are visible only on mGig supporting devices. |
You cannot configure speed on the 10-Gigabit Ethernet ports.
Except for the 1000BASE-T small form-factor pluggable (SFP) modules, you can configure the speed to not negotiate (nonegotiate) when an SFP module port is connected to a device that does not support autonegotiation.
The new keywords: 2500, and 5000 are visible only on mGig supporting devices.
If the speed is set to auto, the switch negotiates with the device at the other end of the link for the speed setting and then forces the speed setting to the negotiated value. The duplex setting remains as configured on each end of the link, which could result in a duplex setting mismatch.
If both ends of the line support autonegotiation, we highly recommend the default autonegotiation settings. If one interface supports autonegotiation and the other end does not, do use the auto setting on the supported side, but set the duplex and speed on the other side.
![]() Caution | Changing the interface speed and duplex mode configuration might shut down and reenable the interface during the reconfiguration. |
For guidelines on setting the switch speed and duplex parameters, see the “Configuring Interface Characteristics” chapter in the software configuration guide for this release.
You can verify your settings by entering the show interfaces privileged EXEC command.
This example shows how to set speed on a port to 100 Mb/s:
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# speed 100
This example shows how to set a port to autonegotiate at only 10 Mb/s:
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# speed auto 10
This example shows how to set a port to autonegotiate at only 10 or 100 Mb/s:
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# speed auto 10 100
To configure StackPower parameters for the power stack or for a switch in the power stack, use the stack power command in global configuration mode. To return to the default setting, use the no form of the command,
stack-power { stack power-stack-name | switch stack-member-number }
no stack-power { stack power-stack-name | switch stack-member-number }
stack power-stack-name |
Specifies the name of the power stack. The name can be up to 31 characters. Entering these keywords followed by a carriage return enters power stack configuration mode. |
switch stack-member-number |
Specifies the switch number in the stack (1 to 4) to enter switch stack-power configuration mode for the switch. |
There is no default.
Global configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
When you enter the stack-power stack power stack name command, you enter power stack configuration mode, and these commands are available:
If you enter the stack-power switch switch-number command with a switch number that is not participating in StackPower, you receive an error message.
When you enter the stack-power switch switch-number command with the number of a switch participating in StackPower, you enter switch stack power configuration mode, and these commands are available:
This example removes switch 2, which is connected to the power stack, from the power pool and shutting down both power ports:
Switch(config)# stack-power switch 2 Switch(config-switch-stackpower)# standalone Switch(config-switch-stackpower)# exit
To configure Flex Links, use the switchport backup interface command in interface configuration mode on a Layer 2 interface on the switch stack or on a standalone switch. To remove the Flex Links configuration, use the no form of this command.
switchport backup interface interface-id [ mmu primary vlan vlan-id | multicast fast-convergence | preemption { delay seconds | mode { bandwidth | forced | off } } | prefer vlan vlan-id ]
no switchport backup interface interface-id [ mmu primary vlan | multicast fast-convergence | preemption { delay | mode } | prefer vlan ]
interface-id |
ID of the physical interface. |
mmu |
(Optional) Configures the MAC move update (MMU) for a backup interface pair. |
primary vlan vlan-id |
(Optional) VLAN ID of the primary VLAN. The range is 1 to 4094. |
multicast fast-convergence |
(Optional) Configures multicast fast convergence on the backup interface. |
preemption |
(Optional) Configures a preemption scheme for a backup interface pair. |
delay seconds |
Specifies a preemption delay. The range is 1 to 300 seconds. The default is 35 seconds. |
mode |
Specifies the preemption mode. |
bandwidth |
Specifies that a higher bandwidth interface is preferred. |
forced |
Specifies that an active interface is preferred. |
off |
Specifies that no preemption occurs from backup to active. |
prefer vlan vlan-id |
(Optional) Specifies that VLANs are carried on the backup interfaces of a Flex Link pair. VLAN ID range is 1 to 4094. |
The default is to have no Flex Links defined. The preemption mode is off. No preemption occurs. Preemption delay is set to 35 seconds.
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
Flex Links are a pair of interfaces that provide backup to each other. With Flex Links configured, one link acts as the primary interface and forwards traffic, while the other interface is in standby mode, ready to begin forwarding traffic if the primary link shuts down. The interface being configured is referred to as the active link; the specified interface is identified as the backup link. The feature provides an alternative to the Spanning Tree Protocol (STP), allowing users to turn off STP and still retain basic link redundancy.
This command is available only for Layer 2 interfaces.
You can configure only one Flex Link backup link for any active link, and it must be a different interface from the active interface.
An interface can belong to only one Flex Link pair. An interface can be a backup link for only one active link. An active link cannot belong to another Flex Link pair.
A backup link does not have to be the same type (Fast Ethernet or Gigabit Ethernet, for instance) as the active link. However, you should configure both Flex Links with similar characteristics so that there are no loops or changes in behavior if the standby link begins to forward traffic.
Neither of the links can be a port that belongs to an EtherChannel. However, you can configure two port channels (EtherChannel logical interfaces) as Flex Links, and you can configure a port channel and a physical interface as Flex Links, with either the port channel or the physical interface as the active link.
If STP is configured on the switch, Flex Links do not participate in STP in all valid VLANs. If STP is not running, be sure that there are no loops in the configured topology.
This example shows how to configure two interfaces as Flex Links:
Switch# configure terminal Switch(conf)# interface gigabitethernet1/0/1 Switch(conf-if)# switchport backup interface gigabitethernet1/0/2 Switch(conf-if)# end
This example shows how to configure the Gigabit Ethernet interface to always preempt the backup:
Switch# configure terminal Switch(conf)# interface gigabitethernet1/0/1 Switch(conf-if)# switchport backup interface gigabitethernet1/0/2 preemption forced Switch(conf-if)# end
This example shows how to configure the Gigabit Ethernet interface preemption delay time:
Switch# configure terminal Switch(conf)# interface gigabitethernet1/0/1 Switch(conf-if)# switchport backup interface gigabitethernet1/0/2 preemption delay 150 Switch(conf-if)# end
This example shows how to configure the Gigabit Ethernet interface as the MMU primary VLAN:
Switch# configure terminal Switch(conf)# interface gigabitethernet1/0/1 Switch(conf-if)# switchport backup interface gigabitethernet1/0/2 mmu primary vlan 1021 Switch(conf-if)# end
You can verify your setting by entering the show interfaces switchport backup privileged EXEC command.
To prevent unknown multicast or unicast packets from being forwarded, use the switchport block command in interface configuration mode. To allow forwarding unknown multicast or unicast packets, use the no form of this command.
switchport block { multicast | unicast }
no switchport block { multicast | unicast }
multicast |
Specifies that unknown multicast traffic should be blocked.
|
||
unicast |
Specifies that unknown unicast traffic should be blocked. |
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
By default, all traffic with unknown MAC addresses is sent to all ports. You can block unknown multicast or unicast traffic on protected or nonprotected ports. If unknown multicast or unicast traffic is not blocked on a protected port, there could be security issues.
With multicast traffic, the port blocking feature blocks only pure Layer 2 packets. Multicast packets that contain IPv4 or IPv6 information in the header are not blocked.
Blocking unknown multicast or unicast traffic is not automatically enabled on protected ports; you must explicitly configure it.
For more information about blocking packets, see the software configuration guide for this release.
This example shows how to block unknown unicast traffic on an interface:
Switch(config-if)# switchport block unicast
You can verify your setting by entering the show interfaces interface-id switchport privileged EXEC command.
To set the global maximum packet size or MTU size for switched packets on Gigabit Ethernet and 10-Gigabit Ethernet ports, use the system mtu command in global configuration mode. To restore the global MTU value to its default value use the no form of this command.
system mtu bytes
no system mtu
bytes |
The global MTU size in bytes. The range is 1500 to 9198 bytes; the default is 1500 bytes. |
The default MTU size for all ports is 1500 bytes.
Global configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
You can verify your setting by entering the show system mtu privileged EXEC command.
The switch does not support the MTU on a per-interface basis.
If you enter a value that is outside the allowed range for the specific type of interface, the value is not accepted.
This example shows how to set the global system MTU size to 6000 bytes:
Switch(config)# system mtu 6000
Global Ethernet MTU is set to 6000 bytes.
Note: this is the Ethernet payload size, not the total
Ethernet frame size, which includes the Ethernet
header/trailer and possibly other tags, such as ISL or
802.1q tags.
To create a network-policy profile for the voice-signaling application type, use the voice-signaling vlan command in network-policy configuration mode. To delete the policy, use the no form of this command.
voice-signaling vlan { vlan-id [ cos cos-value | dscp dscp-value ] | dot1p [ cos l2-priority | dscp dscp ] | none | untagged }
vlan-id |
(Optional) The VLAN for voice traffic. The range is 1 to 4094. |
cos cos-value |
(Optional) Specifies the Layer 2 priority class of service (CoS) for the configured VLAN. The range is 0 to 7; the default is 5. |
dscp dscp-value |
(Optional) Specifies the differentiated services code point (DSCP) value for the configured VLAN. The range is 0 to 63; the default is 46. |
dot1p |
(Optional) Configures the phone to use IEEE 802.1p priority tagging and to use VLAN 0 (the native VLAN). |
none |
(Optional) Does not instruct the Cisco IP phone about the voice VLAN. The phone uses the configuration from the phone key pad. |
untagged |
(Optional) Configures the phone to send untagged voice traffic. This is the default for the phone. |
No network-policy profiles for the voice-signaling application type are defined.
The default CoS value is 5.
The default DSCP value is 46.
The default tagging mode is untagged.
Network-policy profile configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
Use the network-policy profile global configuration command to create a profile and to enter network-policy profile configuration mode.
The voice-signaling application type is for network topologies that require a different policy for voice signaling than for voice media. This application type should not be advertised if all of the same network policies apply as those advertised in the voice policy TLV.
When you are in network-policy profile configuration mode, you can create the profile for voice-signaling by specifying the values for VLAN, class of service (CoS), differentiated services code point (DSCP), and tagging mode.
These profile attributes are contained in the Link Layer Discovery Protocol for Media Endpoint Devices (LLDP-MED) network-policy time-length-value (TLV).
To return to privileged EXEC mode from the network-policy profile configuration mode, enter the exit command.
This example shows how to configure voice-signaling for VLAN 200 with a priority 2 CoS:
Switch(config)# network-policy profile 1 Switch(config-network-policy)# voice-signaling vlan 200 cos 2
This example shows how to configure voice-signaling for VLAN 400 with a DSCP value of 45:
Switch(config)# network-policy profile 1 Switch(config-network-policy)# voice-signaling vlan 400 dscp 45
This example shows how to configure voice-signaling for the native VLAN with priority tagging:
Switch(config-network-policy)# voice-signaling vlan dot1p cos 4
To create a network-policy profile for the voice application type, use the voice vlan command in network-policy configuration mode. To delete the policy, use the no form of this command.
voice vlan { vlan-id [ cos cos-value | dscp dscp-value ] | dot1p [ cos l2-priority | dscp dscp ] | none | untagged }
vlan-id |
(Optional) The VLAN for voice traffic. The range is 1 to 4094. |
cos cos-value |
(Optional) Specifies the Layer 2 priority class of service (CoS) for the configured VLAN. The range is 0 to 7; the default is 5. |
dscp dscp-value |
(Optional) Specifies the differentiated services code point (DSCP) value for the configured VLAN. The range is 0 to 63; the default is 46. |
dot1p |
(Optional) Configures the phone to use IEEE 802.1p priority tagging and to use VLAN 0 (the native VLAN). |
none |
(Optional) Does not instruct the Cisco IP phone about the voice VLAN. The phone uses the configuration from the phone key pad. |
untagged |
(Optional) Configures the phone to send untagged voice traffic. This is the default for the phone. |
No network-policy profiles for the voice application type are defined.
The default CoS value is 5.
The default DSCP value is 46.
The default tagging mode is untagged.
Network-policy profile configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
Use the network-policy profile global configuration command to create a profile and to enter network-policy profile configuration mode.
The voice application type is for dedicated IP telephones and similar devices that support interactive voice services. These devices are typically deployed on a separate VLAN for ease of deployment and enhanced security through isolation from data applications.
When you are in network-policy profile configuration mode, you can create the profile for voice by specifying the values for VLAN, class of service (CoS), differentiated services code point (DSCP), and tagging mode.
These profile attributes are contained in the Link Layer Discovery Protocol for Media Endpoint Devices (LLDP-MED) network-policy time-length-value (TLV).
To return to privileged EXEC mode from the network-policy profile configuration mode, enter the exit command.
This example shows how to configure the voice application type for VLAN 100 with a priority 4 CoS:
Switch(config)# network-policy profile 1 Switch(config-network-policy)# voice vlan 100 cos 4
This example shows how to configure the voice application type for VLAN 100 with a DSCP value of 34:
Switch(config)# network-policy profile 1 Switch(config-network-policy)# voice vlan 100 dscp 34
This example shows how to configure the voice application type for the native VLAN with priority tagging:
Switch(config-network-policy)# voice vlan dot1p cos 4
To configure the wireless AP-manager interface, use the wireless ap-manager interface command.
wireless ap-managerinterface { TenGigabitEthernet interface-number | Vlan interface-number }
TenGigabitEthernet interface-name |
Configures 10-Gigabit Ethernet interface. Values range from 0 to 9. |
Vlan interface-name |
Configures VLANs. Values range from 1 to 4095. |
None
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to configure the wireless AP-manager:
Switch# wireless ap-manager interface vlan
<1-4095> Vlan interface number
This example shows how to configure the wireless AP-manager:
Switch# #wireless ap-manager interface vlan 10
To manage exclusion list entries, use the wireless exclusionlist global configuration command. To remove the exclusion list entries, use the no form of the command.
wireless exclusionlist mac-addr description description
no wireless exclusionlist mac-addr
mac-addr |
The MAC address of the local excluded entry. |
description description |
Specifies the description for an exclusion-list entry. |
None
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to create a local exclusion list entry for the MAC address xxx.xxx.xxx:
Switch# wireless exclusionlist xxx.xxx.xxx
This example shows how to create a description for the local exclusion list entry for the MAC address xxx.xxx.xxx:
Switch# wireless exclusionlist xxx.xxx.xxx description sample
To configure linktest frame size and number of frames to send, use the wireless linktest command.
wireless linktest { frame-size size | number-of-frames value }
frame-size size |
Specifies the link test frame size for each packet. The values range from 1 to 1400. |
number-of-frames value |
Specifies the number of frames to be sent for the link test. The values range from 1 to 100. |
None
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to configure the link test frame size of each frame as 10:
Switch# wireless linktest frame-size 10
To configure wireless management parameters on an interface, use the wireless management interface global configuration command. To remove a wireless management parameters on an interface, use the no form of the command.
wireless management interface interface-name { TenGigabitEthernet interface-name | Vlan interface-name }
no wireless management interface
interface-name | The interface number. |
TenGigabitEthernet interface-name |
The 10-Gigabit Ethernet interface number. The values range from 0 to 9. |
Vlan interface-name | The VLAN interface number. The values range from 1 to 4095. |
None
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to configure VLAN 10 on the wireless interface:
Switch# wireless management interface Vlan 10
To configure peer-to-peer blocking for forward upstream, use the wireless peer-blocking forward-upstream command. To remove a peer-to-peer blocking, use the no form of the command.
wireless peer-blocking forward-upstream interface { GigabitEthernet interface-number TenGigabitEthernet interface-number }
no wireless peer-blocking forward-upstream { GigabitEthernet interface-number TenGigabitEthernet interface-number }
GigabitEthernet interface |
The Gigabit Ethernet interface number. Values range from 0 to 9. |
TenGigabitEthernet interface |
The 10-Gigabit Ethernet interface number. Values range from 0 to 9. |
None
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to configure peer-to-peer blocking for interface 10-gigabit ethernet interface:
Switch(config)# wireless peer-blocking forward-upstream TenGigabitEthernet 1/1/4