The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
To enable AAA override on the WLAN, use the aaa-override command. To disable AAA override, use the no form of this command.
aaa-override
no aaa-override
This command has no keywords or arguments.
AAA is disabled by default.
WLAN configuration
Release |
Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable AAA on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# shutdown Switch(config-wlan)# aaa-override Switch(config-wlan)# no shutdown Switch(config-wlan)# end
This example shows how to disable AAA on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# shutdown Switch(config-wlan)# no aaa-override Switch(config-wlan)# no shutdown Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To configure RADIUS accounting servers on a WLAN, use the accounting-list command. To disable RADIUS server accounting, use the no form of this command.
accounting-list radius-server-acct
no accounting-list
radius-server-acct |
Accounting RADIUS server name. |
RADIUS server accounting is disabled by default.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to configure RADIUS server accounting on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# accounting-list test Switch(config-wlan)# end
This example shows how to disable RADIUS server accounting on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no accounting-list test Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To enable PoE in the LAN port of AP, use the ap name ap-name lan port-id port-id poe command in privileged EXEC mode. To disable PoE in the LAN port of AP, use no form of this command.
![]() Note | PoE can be configured only for port 1. |
ap name ap-name lan port-id port-id poe
no ap name ap-name lan port-id port-id poe
ap-name |
Name of the AP. |
port-id |
ID of the port. |
None
privileged EXEC
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to enable PoE in the LAN port of AP:
Switch # ap name AP00FE.C82D.DFB0 lan port-id 1 poe
To enable Override in an AP group LAN port configuration, use the ap name ap-name lan override command in privileged EXEC mode. To disable Override in an AP group LAN port configuration, use no form of this command.
ap name ap-name lan override
no ap name ap-name lan override
ap-name |
Name of the AP. |
None
privileged EXEC
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to enable Override in an AP group LAN port configuration:
Switch # ap name AP00FE.C82D.DFB0 lan override
To configure band selection on a WLAN, use the band-select command. To disable band selection, use the no form of this command.
band-select
no band-select
This command has no keywords or arguments.
Band selection is disabled by default.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
When you enable band select on a WLAN, the access point suppresses client probes on 2.4GHz and moves the dual band clients to the 5-GHz spectrum. The band-selection algorithm directs dual-band clients only from the 2.4-GHz radio to the 5-GHz radio of the same access point, and it only runs on an access point when both the 2.4-GHz and 5-GHz radios are up and running.
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable band select on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# band-select Switch(config-wlan)# end
This example shows how to disable band selection on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no band-select Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To enable a Service Set Identifier (SSID) on a WLAN, use the broadcast-ssid command. To disable broadcasting of SSID, use the no form of this command.
broadcast-ssid
no broadcast-ssid
This command has no keywords or arguments.
The SSIDs of WLANs are broadcasted by default.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable a broadcast SSID on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# broadcast-ssid Switch(config-wlan)# end
This example shows how to disable a broadcast SSID on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no broadcast-ssid Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To enable Voice over IP (VoIP) snooping on a WLAN, use the call-snoop command. To disable Voice over IP (VoIP), use the no form of this command.
call-snoop
no call-snoop
This command has no keywords or arguments.
VoIP snooping is disabled by default.
WLN configuration
You must disable the WLAN before using this command. See the Related Commands section for more information on how to disable a WLAN.
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
The WLAN on which call snooping is configured must be configured with Platinum QoS. You must disable quality of service before using this command. See Related Commands section for more information on configuring QoS service-policy.
This example shows how to enable VoIP on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# call-snoop Switch(config-wlan)# end
This example shows how to disable VoIP on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no call-snoop Switch(config-wlan)# end
Command | Description |
Configures the QoS Policy on a WLAN. | |
Creates or disables a WLAN. |
To configure the device to defer priority markings for packets that can defer off-channel scanning, use the channel-scan defer-priority command. To disable the device to defer priority markings for packets that can defer off-channel scanning, use the no form of this command.
channel-scan defer-priority priority
no channel-scan defer-priority priority
priority |
Channel priority value. The range is 0 to 7. The default is 3. |
Channel scan defer is enabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to enable channel scan defer priority on a WLAN and set it to a priority value 4:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# channel-scan defer-priority 4 Switch(config-wlan)# end
This example shows how to disable channel scan defer priority on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no channel-scan defer-priority 4 Switch(config-wlan)# end
To assign a channel scan defer time, use the channel-scan defer-time command. To disable the channel scan defer time, use the no form of this command.
channel-scan defer-time msecs
no channel-scan defer-time
msecs |
Deferral time in milliseconds. The range is from 0 to 60000. The default is 100. |
Channel-scan defer time is enabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
The time value in milliseconds should match the requirements of the equipment on the WLAN.
This example shows how to enable a channel scan on the WLAN and set the scan deferral time to 300 milliseconds:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# channel-scan defer-time 300 Switch(config-wlan)# end
This example shows how to disable channel scan defer time on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no channel-scan defer-time Switch(config-wlan)# end
To enable coverage hole detection on a WLAN, use the chd command. To disable coverage hole detection, use the no form of this command.
chd
no chd
This command has no keywords or arguments.
Coverage hole detection is enabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to enable coverage hole detection on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# chd Switch(config-wlan)# end
This example shows how to disable coverage hole detection on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no chd Switch(config-wlan)# end
To configure the maximum number of client connections on a WLAN, use the client association limit command. To disable clients association limit on the WLAN, use the no form of this command.
client association limit { association-limit }
no client association limit { association-limit }
association-limit |
Number of client connections to be accepted. The range is from 0 to 2000. A value of zero (0) indicates no set limit. |
The maximum number of client connections is set to 0 (no limit).
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to configure a client association limit on a WLAN and configure the client limit to 200:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# shutdown Switch(config-wlan)# client association limit 200 Switch(config-wlan)# no shutdown Switch(config-wlan)# end
This example shows how to disable a client association limit on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# shutdown Switch(config-wlan)# no client association limit Switch(config-wlan)# no shutdown Switch(config-wlan)# end
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# client association limit radio 200 Switch(config-wlan)# no shutdown Switch(config-wlan)# end
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# client association limit ap 300 Switch(config-wlan)# no shutdown Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To configure a WLAN interface or an interface group, use the client vlan command. To disable the WLAN interface, use the no form of this command.
client vlan interface-id-name-or-group-name
no client vlan
interface-id-name-or-group-name |
Interface ID, name, or VLAN group name. The interface ID can also be in digits too. |
The default interface is configured.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable a client VLAN on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# client vlan client-vlan1 Switch(config-wlan)# end
This example shows how to disable a client VLAN on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no client vlan Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To enable Aironet Information Elements (IEs) for a WLAN, use the ccx aironet-iesupport command. To disable Aironet Information Elements (IEs), use the no form of this command.
ccx aironet-iesupport
no ccx aironet-iesupport
This command has no keywords or arguments.
Aironet IE support is enabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable an Aironet IE for a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# ccx aironet-iesupport Switch(config-wlan)# end
This example shows how to disable an Aironet IE on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no ccx aironet-iesupport Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To enable NetFlow monitoring in a WLAN, use the datalink flow monitor command. To disable NetFlow monitoring, use the no form of this command.
datalink flow monitor datalink-monitor-name { input | output }
no datalink flow monitor datalink-monitor-name { input | output }
datalink-monitor-name |
Flow monitor name. The datalink monitor name can have up to 31 characters. |
input |
Specifies the NetFlow monitor for ingress traffic. |
output |
Specifies the NetFlow monitor for egress traffic. |
None.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable NetFlow monitoring on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# datalink flow monitor test output Switch(config-wlan)# end
This example shows how to disable NetFlow monitoring on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no datalink flow monitor test output Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To enable client device classification in a WLAN, use the device-classification command. To disable device classification, use the no form of this command.
device-classification
no device-classification
device-classification |
Enables/Disables Client Device Classification. |
None.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# device-classification Switch(config-wlan)# end
To set the parameters to their default values, use the default command.
default { aaa-override | accounting-list | band-select | broadcast-ssid | call-snoop | ccx | channel-scan | parameters | chd | client | datalink | diag-channel | dtim | exclusionlist | ip | ipv6 | load-balance | local-auth | mac-filtering | media-stream | mfp | mobility | nac | passive-client | peer-blocking | radio | roamed-voice-client | security | service-policy | session-timeout | shutdown | sip-cac | static-ip | uapsd | wgb | wmm }
aaa-override |
Sets the AAA override parameter to its default value. |
accounting-list |
Sets the accounting parameter and its attributes to their default values. |
band-select | Sets the band selection parameter to its default values. |
broadcast-ssid | Sets the broadcast Service Set Identifier (SSID) parameter to its default value. |
call-snoop | Sets the call snoop parameter to its default value. |
ccx | Sets the Cisco client extension (Cisco Aironet IE) parameters and attributes to their default values. |
channel-scan | Sets the channel scan parameters and attributes to their default values. |
chd | Sets the coverage hold detection parameter to its default value. |
client | Sets the client parameters and attributes to their default values. |
datalink | Sets the datalink parameters and attributes to their default values. |
diag-channel | Sets the diagnostic channel parameters and attributes to their default values. |
dtim | Sets the Delivery Traffic Indicator Message (DTIM) parameter to its default value. |
exclusionlist | Sets the client exclusion timeout parameter to its default value. |
ip | Sets the IP parameters to their default values. |
ipv6 | Sets the IPv6 parameters and attributes to their default values. |
load-balance | Sets the load-balancing parameter to its default value. |
local-auth | Sets the Extensible Authentication Protocol (EAP) profile parameters and attributes to their default values. |
mac-filtering | Sets the MAC filtering parameters and attributes to their default values. |
media-stream | Sets the media stream parameters and attributes to their default values. |
mfp | Sets the Management Frame Protection (MPF) parameters and attributes to their default values. |
mobility | Sets the mobility parameters and attributes to their default values. |
nac | Sets the RADIUS Network Admission Control (NAC) parameter to its default value. |
passive-client | Sets the passive client parameter to its default value. |
peer-blocking | Sets the peer to peer blocking parameters and attributes to their default values. |
radio | Sets the radio policy parameters and attributes to their default values. |
roamed-voice-client | Sets the roamed voice client parameters and attributes to their default values. |
security | Sets the security policy parameters and attributes to their default values. |
service-policy | Sets the WLAN quality of service (QoS) policy parameters and attributes to their default values. |
session-timeout | Sets the client session timeout parameter to its default value. |
shutdown | Sets the shutdown parameter to its default value. |
sip-cac | Sets the Session Initiation Protocol (SIP) Call Admission Control (CAC) parameters and attributes to their default values. |
static-ip | Sets the static IP client tunneling parameters and their attributes to their default values. |
uapsd | Sets the Wi-Fi Multimedia (WMM) Unscheduled Automatic Power Save Delivery (UAPSD) parameters and attributes to their default values. |
wgb | Sets the Workgroup Bridges (WGB) parameter to its default value. |
wmm | Sets the WMM parameters and attributes to their default values. |
None.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to set the Cisco Client Extension parameter to its default value:
Switch(config-wlan)# default ccx aironet-iesupport
Command | Description |
Creates or disables a WLAN. |
To configure the Delivery Traffic Indicator Message (DTIM) period for a WLAN, use the dtim dot11 command. To disable DTIM, use the no form of this command.
dtim dot11 { 5ghz | 24ghz } dtim-period
no dtim dot11 { 5ghz | 24ghz } dtim-period
5ghz |
Configures the DTIM period on the 5-GHz band. |
24ghz |
Configures the DTIM period on the 2.4-GHz band. |
dtim-period |
Value for the DTIM period. The range is from 1 to 255. |
The DTIM period is set to 1.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable the DTIM period on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# dtim dot11 24ghz 3
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no dtim dot11 24ghz 3
Command | Description |
Creates or disables a WLAN. |
To configure an exclusion list on a wireless LAN, use the exclusionlist command. To disable an exclusion list, use the no form of this command.
exclusionlist [ timeout seconds ]
no exclusionlist [timeout]
timeout seconds |
(Optional) Specifies an exclusion list timeout in seconds. The range is from 0 to 2147483647. A value of zero (0) specifies no timeout. |
The exclusion list is set to 60 seconds.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to configure a client exclusion list for a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# exclusionlist timeout 345
This example shows how to disable a client exclusion list on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no exclusionlist timeout 345
To exit the WLAN configuration submode, use the exit command.
exit
This command has no keywords or arguments.
None
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to exit the WLAN configuration submode:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# exit Switch(config)#
To exit the WLAN access point group submode, use the exit command.
exit
This command has no keywords or arguments.
None
WLAN AP Group configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to exit the WLAN AP group submode:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# ap group test Switch(config-apgroup)# exit
To configure WLAN access control group (ACL), use the ip access-group command. To remove a WLAN ACL group, use the no form of the command.
ip access-group [web] acl-name
no ip access-group [web]
web |
(Optional) Configures the IPv4 web ACL. |
acl-name |
Specify the preauth ACL used for the WLAN with the security type value as webauth. |
None
WLAN configuration
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to configure a WLAN ACL:
Switch#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#wlan wlan1 Switch(config-wlan)#ip access-group test-acl
This example shows how to configure an IPv4 WLAN web ACL:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# ip access-group web test Switch(config-wlan)#
Command | Description |
Creates or disables a WLAN. |
To configure IP NetFlow monitoring, use the ip flow monitor command. To remove IP NetFlow monitoring, use the no form of this command.
ip flow monitor ip-monitor-name { input | output }
no ip flow monitor ip-monitor-name { input | output }
ip-monitor-name |
Flow monitor name. |
input |
Enables a flow monitor for ingress traffic. |
output |
Enables a flow monitor for egress traffic. |
None
WLAN configuration
You must disable the WLAN before using this command.
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to configure an IP flow monitor for the ingress traffic:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# ip flow monitor test input
This example shows how to disable an IP flow monitor:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no ip flow monitor test input
To enable IPv4 Source Guard (IPSG) on a WLAN, use the ip verify source mac-check command. To disable IPSG, use the no form of this command.
ip verify source mac-check
no ip verify source mac-check
This command has no keywords or arguments.
IPSG is disabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
Use this feature to restrict traffic from a host to a specific interface that is based on the host's IP address. The feature can also be configured to bind the source MAC and IP of a host so that IP spoofing is prevented.
Use this feature to bind the IP and MAC address of a wireless host that is based on information received from DHCP snooping, ARP, and Dataglean. Dataglean is the process of extracting location information such as host hardware address, ports that lead to the host, and so on from DHCP messages as they are forwarded by the DHCP relay agent. If a wireless host tries to send traffic with IP address and MAC address combination that has not been learned by the switch, this traffic is dropped in the hardware. IPSG is not supported on DHCP packets. IPSG is not supported for foreign clients in a foreign switch.
You must disable the WLAN before using this command.
This example shows how to enable IPSG:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# ip verify source mac-check
This example shows how to disable IPSG:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no ip verify source mac-check
To enable load balancing on a WLAN, use the load-balance command. To disable load balancing, use the no form of this command.
load-balance
no load-balance
This command has no keywords or arguments.
Load balancing is disabled by default.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
The command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable load balancing on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# shutdown Switch(config)# wlan wlan1 Switch(config-wlan)# load-balance Switch(config)# no shutdown Switch(config-wlan)# end
This example shows how to disable load balancing on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# shutdown Switch(config)# wlan wlan1 Switch(config-wlan)# no load-balance Switch(config)# no shutdown Switch(config-wlan)# end
Command | Description |
Creates or disables a WLAN. |
To configure mobility sticky anchoring, use the mobility anchor sticky command. To disable the sticky anchoring, use the no form of the command.
To configure guest anchoring, use the mobility anchor ip-address command.
To delete the guest anchor, use the no form of the command.
To configure the device as an auto-anchor, use the mobility anchor command.
mobility anchor { ip-address | sticky }
no mobility anchor { ip-address | sticky }
sticky |
|
||
ip-address |
Configures the IP address for the guest anchor switch to this WLAN. |
Sticky configuration is enabled by default.
WLAN Configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE Cisco IOS XE 3.3SE |
This command was introduced. |
The wlan_id or guest_lan_id must exist and be disabled.
Auto-anchor mobility is enabled for the WLAN or wired guest LAN when you configure the first mobility anchor.
Deleting the last anchor disables the auto-anchor mobility feature and resumes normal mobility for new associations.
Mobility uses the following ports, that are allowed through the firewall:
Switch(config-wlan)# mobility anchor sticky
Switch(config-wlan)# mobility anchor 209.165.200.224
Switch(config-wlan)# mobility anchor
To enable RADIUS Network Admission Control (NAC) support for a WLAN, use the nac command. To disable NAC out-of-band support, use the no form of this command.
nac
no nac
This command has no keywords or arguments.
NAC is disabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You should enable AAA override before you enable the RADIUS NAC state.
This example shows how to configure RADIUS NAC on the WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# aaa-override Switch(config-wlan)# nac
This example shows how to disable RADIUS NAC on the WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no nac Switch(config-wlan)# no aaa-override
Command | Description |
Enables or disables AAA override on a WLAN. |
To enable the passive client feature on a WLAN, use the passive-client command. To disable the passive client feature, use the no form of this command.
passive-client
no passive-client
This command has no keywords or arguments.
Passive client feature is disabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must enable the global multicast mode and multicast-multicast mode before entering this command. Both multicast-multicast mode and multicast unicast modes are supported. The multicast-multicast mode is recommended.
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This show how to enable the passive client feature on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wireless multicast Switch(config)# wlan test-wlan Switch(config-wlan)# passive-client
This example shows how to disable the passive client feature on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wireless multicast Switch(config)# wlan test-wlan Switch(config-wlan)# no passive-client
Command | Description |
Creates or disables a WLAN. |
To configure peer-to-peer blocking on a WLAN, use the peer-blocking command. To disable peer-to-peer blocking, use the no form of this command.
peer-blocking { drop | forward-upstream }
no peer-blocking
drop |
Specifies the switch to discard the packets. |
forward-upstream |
Specifies the packets to be forwarded on the upstream VLAN. The device next in the hierarchy to the switch decides what action to take regarding the packets. |
Peer blocking is disabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable the drop and forward-upstream options for peer-to-peer blocking:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# peer-blocking drop Switch(config-wlan)# peer-blocking forward-upstream
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no peer-blocking drop Switch(config-wlan)# no peer-blocking forward-upstream
Command | Description |
Creates or disables a WLAN. |
To configure port id of an AP group, use the port command in interface configuration mode. To disable a port id of an AP group, use no form of this command.
port port-id
no port port-id
port-id |
ID of the port. |
None
Interface configuration (config-apgroup)
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to configure port id of an AP group:
Switch(config-apgroup)# port-1
To enable PoE on a port, use the poe command in interface configuration mode. To disable PoE on the port, use no form of this command.
![]() Note | PoE can be configured only for port 1. |
poe
no poe
None
Interface configuration (config-apgroup)
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to enable PoE on a port:
Switch(config-apgroup)# poe
To enable the Cisco radio policy on a WLAN, use the radio command. To disable the Cisco radio policy on a WLAN, use the no form of this command.
radio { all | dot11a | dot11ag | dot11bg | dot11g }
no radio
all |
Configures the WLAN on all radio bands. |
dot11a |
Configures the WLAN on only 802.11a radio bands. |
dot11ag | Configures the WLAN on 802.11a/g radio bands. |
dot11bg |
Configures the wireless LAN on only 802.11b/g radio bands (only 802.11b if 802.11g is disabled). |
dot11g |
Configures the wireless LAN on 802.11g radio bands only. |
Radio policy is enabled on all bands.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to configure the WLAN on all radio bands:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# radio all
This example shows how to disable all radio bands on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no radio all
Command | Description |
Creates or disables a WLAN. |
To configure the radio policy on a WLAN access point group, use the radio-policy command. To disable the radio policy on the WLAN, use the no form of this command.
radio-policy { all | dot11a | dot11bg | dot11g }
no radio { all | dot11a | dot11bg | dot11g }
all |
Configures the wireless LAN on all radio bands. |
dot11a |
Configures the wireless LAN on only 802.11a radio bands. |
dot11bg |
Configures the wireless LAN on only 802.11b/g (only 802.11b if 802.11g is disabled) radio bands. |
dot11g |
Configures the wireless LAN on only 802.11g radio bands. |
Radio policy is enabled on all the bands.
WLAN AP Group configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
The WLAN must be restarted for the changes to take effect. See Related Commands section for more information on how to shutdown a WLAN.
This example shows how to enable the radio policy on the 802.11b band for an AP group:
Switch(config)# ap group test Switch(config-apgroup)# wlan test-wlan Switch(config-wlan-apgroup)# radio-policy dot11b
This example shows how to disable the radio policy on the 802.11b band of an AP group:
Switch(config)# ap group test Switch(config-apgroup)# wlan test-wlan Switch(config-wlan-apgroup)# no radio-policy dot11bg
Command | Description |
Creates or disables a WLAN. | |
Disables a WLAN. |
To specify Remote-LAN profile name, use the remote-lan command in global configuration mode. To disable the configured profile name, use no form of this command.
remote-lan profile-name id
no remote-lan profile-name id
profile-name |
Remote-LAN profile name. |
id |
Remote LAN identifier. The range is from 1 to 64. |
None
Global configuration (config)
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to specify Remote-LAN profile name:
Switch(config)# remote-lan test-lan 3
To add a Remote-LAN to an AP group, use the remote-lan command in interface configuration mode. To disable a Remote-LAN in an AP group, use no form of this command.
remote-lan remote-lan-name
no remote-lan remote-lan-name
![]() Note | The remote-lan remote-lan-name command is also required to map a Remote-LAN to a port. |
remote-lan-name |
Name of the Remote-LAN. |
None
Interface configuration (config-apgroup)
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to add a Remote-LAN to an AP group:
Switch(config-apgroup)# remote-lan test-lan
To enable the roamed-voice-client re-anchor feature, use the roamed-voice-client re-anchor command. To disable the roamed-voice-client re-anchor feature, use the no form of this command.
roamed-voice-client re-anchor
no roamed-voice-client re-anchor
This command has no keywords or arguments.
Roamed voice client reanchor feature is disabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable the roamed voice client re-anchor feature:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# roamed-voice-client re-anchor
This example shows how to disable the roamed voice client re-anchor feature:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no roamed-voice-client re-anchor
Command | Description |
Creates or disables a WLAN. |
To change the status of web authentication used on a WLAN, use the security web-auth command. To disable web authentication on a WLAN, use the no form of the command.
security web-auth [ authentication-list authentication-list-name | on-macfilter-failure | parameter-map parameter-map-name ]
no security web-auth [ authentication-list [authentication-list-name] | on-macfilter-failure | parameter-map [parameter-name] ]
authentication-list authentication-list-name |
Sets the authentication list for IEEE 802.1x. |
on-macfilter-failure |
Enables web authentication on MAC failure. |
parameter-map parameter-map-name |
Configures the parameter map. |
Web authentication is disabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SE |
This command was introduced. |
The following example shows how to configure the authentication-list web authentication on a WLAN:
Switch(config-wlan)# security web-auth authentication-list test
To configure the WLAN quality of service (QoS) service policy, use the service-policy command. To disable a QoS policy on a WLAN, use the no form of this command.
service-policy [client] { input | output } policy-name
no service-policy [client] { input | output } policy-name
client |
(Optional) Assigns a policy map to all clients in the WLAN. |
input |
Assigns an input policy map. |
output | Assigns an output policy map. |
policy-name |
The policy name. |
No policies are assigned and the state assigned to the policy is None.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to configure the input QoS service policy on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# service-policy input policy-test
This example shows how to disable the input QoS service policy on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no service-policy input policy-test
This example shows how to configure the output QoS service policy on a WLAN to platinum (precious metal policy):
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# service-policy output platinum
Command | Description |
Creates or disables a WLAN. |
To configure session timeout for clients associated to a WLAN, use the session-timeout command. To disable a session timeout for clients that are associated to a WLAN, use the no form of this command.
session-timeout seconds
no session-timeout
seconds |
Timeout or session duration in seconds. A value of zero (0) is equivalent to no timeout. The range is from 300 to 86400. |
The client timeout is set to 1800 seconds for WLANs that are configured with dot1x security. The client timeout is set to 0 for open WLANs.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to configure a session timeout to 300 seconds:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# session-timeout 300
This example shows how to disable a session timeout:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no session-timeout
To display Remote-LAN properties of all configured Remote-LANs, use the show remote-lan all command.
show remote-lan all
This command has no keywords or arguments.
None
Privileged EXEC (#)
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example displays Remote-LAN properties of all configured Remote-LANs:
Switch#show remote-lan all
Remote-LAN Profile Name : test
================================================
Identifier : 1
Status : Disabled
Universal AP Admin : Disabled
Max Associated Clients per Remote-LAN : 0
AAA Policy Override : Disabled
Number of Active Clients : 0
Exclusionlist Timeout : 60
Session Timeout : 1800 seconds
Interface : default
Interface Status : Up
Remote-LAN ACL : unconfigured
DHCP Server : 0.0.0.0
DHCP Address Assignment Required : Disabled
Local EAP Authentication : Disabled
Mac Filter Authorization list name : Disabled
Accounting list name : Disabled
802.1x authentication list name : Disabled
Security
802.11 Authentication : Open System
802.1X : Disabled
Web Based Authentication : Disabled
Conditional Web Redirect : Disabled
Splash-Page Web Redirect : Disabled
Webauth On-mac-filter Failure : Disabled
Webauth Authentication List Name : Disabled
Webauth Parameter Map : Disabled
To display the Remote-LAN configuration by ID, use the show remote-lan id command.
show remote-lan id id
id |
Remote LAN identifier. The range is from 1 to 64. |
None
Privileged EXEC (#)
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to display the Remote-LAN configuration by ID:
Switch #show remote-lan id 2
Remote-LAN Profile Name : test
================================================
Identifier : 2
Status : Disabled
Universal AP Admin : Disabled
Max Associated Clients per Remote-LAN : 0
AAA Policy Override : Enabled
Number of Active Clients : 0
Exclusionlist Timeout : 21474
Session Timeout : 864 seconds
Interface : default
Interface Status : Up
Remote-LAN ACL : testacl
DHCP Server : 10.5.7.9
DHCP Address Assignment Required : Disabled
Local EAP Authentication : testeapprofile
Mac Filter Authorization list name : testmaclist
Accounting list name : testlist
802.1x authentication list name : dotxauth
Security
802.11 Authentication : Open System
802.1X : Enabled
Encryption : 104-bit WEP
To display Remote-LAN configuration by profile name, use the show remote-lan name command.
show remote-lan name name
name |
Remote-LAN profile name. |
None
Privileged EXEC (#)
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to display Remote-LAN configuration by profile name:
Switch# show remote-lan name test
Remote-LAN Profile Name : test
================================================
Identifier : 1
Status : Disabled
Universal AP Admin : Disabled
Max Associated Clients per Remote-LAN : 0
AAA Policy Override : Disabled
Number of Active Clients : 0
Exclusionlist Timeout : 60
Session Timeout : 1800 seconds
Interface : default
Interface Status : Up
Remote-LAN ACL : unconfigured
DHCP Server : 0.0.0.0
DHCP Address Assignment Required : Disabled
Local EAP Authentication : Disabled
Mac Filter Authorization list name : Disabled
Accounting list name : Disabled
802.1x authentication list name : Disabled
Security
802.11 Authentication : Open System
802.1X : Disabled
Web Based Authentication : Disabled
Conditional Web Redirect : Disabled
Splash-Page Web Redirect : Disabled
Webauth On-mac-filter Failure : Disabled
Webauth Authentication List Name : Disabled
Webauth Parameter Map : Disabled
To display the summary of all Remote-LANs, use the show remote-lan summary command.
show remote-lan summary
This command has no keywords or arguments.
None
Privileged EXEC (#)
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to display the summary of all Remote-LANs:
Switch # show remote-lan summary
Number of Remote-LANs: 1
Remote-LAN Profile Name VLAN Status
-------------------------------------------------------
2 test 1 DOWN
To display Remote-LAN configuration, use the show running-config remote-lan command.
show running-config remote-lan name
name |
Remote-LAN profile name. |
None
Privileged EXEC (#)
Release | Modification |
---|---|
Cisco IOS XE Denali 16.3.1 |
This command was introduced. |
The following example shows how to display Remote-LAN configuration:
Switch# show running-config remote-lan test
remote-lan test 1
aaa-override
accounting-list test-all-list
exclusionlist timeout 100
ip access-group test-acl
ip dhcp server 10.100.12.5
mac-filtering test-mac-list
security dot1x authentication-list test-dot1x-list
session-timeout 100
shutdown
To view WLAN parameters, use the show wlan command.
show wlan { all | id wlan-id | name wlan-name | summary }
all | Displays a summary of parameters of all configured WLANs. The list is ordered by the ascending order of the WLAN IDs. |
id wlan-id |
Specifies the wireless LAN identifier. The range is from 1 to 512. |
name wlan-name |
Specifies the WLAN profile name. The name is from 1 to 32 characters. |
summary |
Displays a summary of the parameters configured on a WLAN. |
None
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to display a summary of the WLANs configured on the device:
Switch# show wlan summary
Number of WLANs: 1
WLAN Profile Name SSID VLAN Status
--------------------------------------------------------------------------------
45 test-wlan test-wlan-ssid 1 UP
This example shows how to display a summary of parameters configured on a particular WLAN:
Switch# show wlan name test-wlan
WLAN Identifier : 45
Profile Name : test-wlan
Network Name (SSID) : test-wlan-ssid
Status : Enabled
Broadcast SSID : Enabled
Maximum number of Associated Clients : 0
AAA Policy Override : Disabled
Network Admission Control
NAC-State : Disabled
Number of Active Clients : 0
Exclusionlist Timeout : 60
Session Timeout : 1800 seconds
CHD per WLAN : Enabled
Webauth DHCP exclusion : Disabled
Interface : default
Interface Status : Up
Multicast Interface : test
WLAN IPv4 ACL : test
WLAN IPv6 ACL : unconfigured
DHCP Server : Default
DHCP Address Assignment Required : Disabled
DHCP Option 82 : Disabled
DHCP Option 82 Format : ap-mac
DHCP Option 82 Ascii Mode : Disabled
DHCP Option 82 Rid Mode : Disabled
QoS Service Policy - Input
Policy Name : unknown
Policy State : None
QoS Service Policy - Output
Policy Name : unknown
Policy State : None
QoS Client Service Policy
Input Policy Name : unknown
Output Policy Name : unknown
WifiDirect : Disabled
WMM : Disabled
Channel Scan Defer Priority:
Priority (default) : 4
Priority (default) : 5
Priority (default) : 6
Scan Defer Time (msecs) : 100
Media Stream Multicast-direct : Disabled
CCX - AironetIe Support : Enabled
CCX - Gratuitous ProbeResponse (GPR) : Disabled
CCX - Diagnostics Channel Capability : Disabled
Dot11-Phone Mode (7920) : Invalid
Wired Protocol : None
Peer-to-Peer Blocking Action : Disabled
Radio Policy : All
DTIM period for 802.11a radio : 1
DTIM period for 802.11b radio : 1
Local EAP Authentication : Disabled
Mac Filter Authorization list name : Disabled
Accounting list name : Disabled
802.1x authentication list name : Disabled
Security
802.11 Authentication : Open System
Static WEP Keys : Disabled
802.1X : Disabled
Wi-Fi Protected Access (WPA/WPA2) : Enabled
WPA (SSN IE) : Disabled
WPA2 (RSN IE) : Enabled
TKIP Cipher : Disabled
AES Cipher : Enabled
Auth Key Management
802.1x : Enabled
PSK : Disabled
CCKM : Disabled
IP Security : Disabled
IP Security Passthru : Disabled
L2TP : Disabled
Web Based Authentication : Disabled
Conditional Web Redirect : Disabled
Splash-Page Web Redirect : Disabled
Auto Anchor : Disabled
Sticky Anchoring : Enabled
Cranite Passthru : Disabled
Fortress Passthru : Disabled
PPTP : Disabled
Infrastructure MFP protection : Enabled
Client MFP : Optional
Webauth On-mac-filter Failure : Disabled
Webauth Authentication List Name : Disabled
Webauth Parameter Map : Disabled
Tkip MIC Countermeasure Hold-down Timer : 60
Call Snooping : Disabled
Passive Client : Disabled
Non Cisco WGB : Disabled
Band Select : Disabled
Load Balancing : Disabled
IP Source Guard : Disabled
Netflow Monitor : test
Direction : Input
Traffic : Datalink
Mobility Anchor List
IP Address
-----------
To display wireless wlan summary, use the show wireless wlan summary command.
show wireless wlan summary
This command has no keywords or arguments. |
None
Release | Modification |
---|---|
15.2(3)E |
This command was introduced. |
The following is a sample output of the show wireless wlan summary command.
Cisco-Controller# show wireless wlan summary Total WLAN Configured: 3 Total Client Count: 0 ID Profile Name SSID Security Radio VLAN Client Status ----------------------------------------------------------------------------------------------------- 1 Test1 xxx WPA1/WPA2 All 1 0 DOWN 2 wlan1 wlan2-ssid WPA1/WPA2 All 1 0 DOWN 3 wlan3 mywlan3 WPA1/WPA2 All 1 0 DOWN
To disable a WLAN, use the shutdown command. To enable a WLAN, use the no form of this command.
shutdown
no shutdown
![]() Note | To enable LAN port in an AP group configuration and Remote-LAN profile, use the no form of this command. |
This command has no keywords or arguments.
None
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to disable a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan test-wlan Switch(config-wlan)# shutdown Switch(config-wlan)# end Switch# show wlan summary Number of WLANs: 1 WLAN Profile Name SSID VLAN Status -------------------------------------------------------------------------------- 45 test-wlan test-wlan-ssid 1 DOWN
This example shows how to enable a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan test-wlan Switch(config-wlan)# no shutdown Switch(config-wlan)# end Switch# show wlan summary Number of WLANs: 1 WLAN Profile Name SSID VLAN Status -------------------------------------------------------------------------------- 45 test-wlan test-wlan-ssid 1 UP
To configure the Session Initiation Protocol (SIP) Call Admission Control (CAC) feature on a WLAN, use the sip-cac command. To disable the SIP CAC feature, use the no form of this command.
sip-cac { disassoc-client | send-486busy }
no sip-cac { disassoc-client | send-486busy }
disassoc-client |
Enables a client disassociation if a CAC failure occurs. |
send-486busy |
Sends a SIP 486 busy message if a CAC failure occurs. |
None
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable a client disassociation and 486 busy message on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# sip-cac disassoc-client Switch(config-wlan)# sip-cac send-486busy
This example shows how to disable a client association and 486 busy message on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no sip-cac disassoc-client Switch(config-wlan)# no sip-cac send-486busy
Command | Description |
Creates or disables a WLAN. |
To enable static IP tunneling on a WLAN, use the static-ip tunneling command. To disable the static IP tunneling feature, use the no form of this command.
static-ip tunneling
no static-ip tunneling
This command has no keywords or arguments.
None
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
This example shows how to enable static-IP tunneling:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# static-ip tunneling
This example shows how to disable static-IP tunneling:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no static-ip tunneling
To assign a VLAN to an AP group, use the vlan command. To remove a VLAN ID, use the no form of this command.
vlan interface-name
no vlan
interface-name |
VLAN interface name. |
No VALN is assigned to the AP group. See Related Commands section for more information on how to disable a WLAN.
WLAN AP Group configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command.
This example shows how to configure a VLAN on an AP group:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# ap group ap-group-1 Switch(config-apgroup)# wlan test-wlan Switch(config-wlan-apgroup)# vlan 3
Command | Description |
Creates or disables a WLAN. |
To configure the WLAN as the universal admin, use the universal-admin command. To remove the configuration, use the no form of this command.
universal-admin
None
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.7.0 E |
This command was introduced. |
Switchenable Switch#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#wlan wlan1 Switch(config-wlan)#universal-admin
To enable non-Cisco Workgroup Bridges (WGB) clients on the WLAN, use the wgb non-cisco command. To disable support for non-Cisco WGB clients, use the no form of this command.
wgb non-cisco
no wgb non-cisco
This command has no keywords or arguments.
Non-Cisco WGB clients are disabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to enable non-Cisco WGBs on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# shutdown Switch(config-wlan)# wgb non-cisco Switch(config-wlan)# no shutdown
This example shows how to disable support for non-Cisco WGB clients on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# shutdown Switch(config-wlan)# no wgb non-cisco Switch(config-wlan)# no shutdown
To configure WLAN parameters of a WLAN in an access point (AP) group, use the wlan command. To remove a WLAN from the AP group, use the no form of this command.
wlan wlan-name
no wlan wlan-name
wlan-name |
WLAN profile name. The range is from 1 to 32 alphanumeric characters. |
WLAN parameters are not configured for an AP group.
AP Group configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
This example shows how to configure WLAN related parameters in the AP group configuration mode:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# ap group test Switch(config-apgroup)# wlan qos-wlan
Command | Description |
Creates or disables a WLAN. |
To create a wireless LAN, use the wlan command. To disable a wireless LAN, use the no form of this command.
wlan [ wlan-name | wlan-name wlan-id | wlan-name wlan-id wlan-ssid ]
no wlan [ wlan-name | wlan-name wlan-id | wlan-name wlan-id wlan-ssid ]
wlan-name |
WLAN profile name. The name is from 1 to 32 alphanumeric characters. |
wlan-id |
Wireless LAN identifier. The range is from 1 to 512. |
wlan-ssid |
SSID. The range is from 1 to 32 alphanumeric characters. |
WLAN is disabled.
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
If you do not specify an SSID, the profile name parameter is used for both the profile name and the SSID. If the management and AP-manager interfaces are mapped to the same port and are members of the same VLAN, you must disable the WLAN before making a port-mapping change to either interface. If the management and AP-manager (Access Point Manager) interfaces are assigned to different VLANs, you do not need to disable the WLAN.
An error message appears if you try to delete a WLAN that is assigned to an access point group. If you proceed, the WLAN is removed from the access point group and from the access point’s radio.
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config)# wlan test-wlan-cr 67 test-wlan-cr-ssid
This example shows how to delete a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config)# no wlan test-wlan-cr 67 test-wlan-cr-ssid
To disable a WLAN, use the wlan shutdown command. To enable a WLAN, use the no form of this command.
wlan shutdown
no wlan shutdown
The WLAN is disabled.
Global configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# shutdown
Command | Description |
Creates or disables a WLAN. |
To enable Wi-Fi Multimedia (WMM) on a WLAN, use the wmm command. To disable WMM on a WLAN, use the no form of this command.
wmm { allowed | require }
no wmm
allowed |
Allows WMM on a WLAN. |
require |
Mandates that clients use WMM on the WLAN. |
WMM is enabled.
WLAN configuration
Release | Modification |
---|---|
Cisco IOS XE 3.3SECisco IOS XE 3.3SE |
This command was introduced. |
When the switch is in Layer 2 mode and WMM is enabled, you must put the access points on a trunk port in order to allow them to join the switch.
You must disable the WLAN before using this command. See Related Commands section for more information on how to disable a WLAN.
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# wmm allowed
This example shows how to disable WMM on a WLAN:
Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# wlan wlan1 Switch(config-wlan)# no wmm
Command | Description |
Creates or disables a WLAN. |