Catalyst 4500 Series Switch Software Configuration Guide, 12.2(40)SG

Configuring 802.1X Port-Based Authentication

This chapter describes how to configure IEEE 802.1X port-based authentication to prevent unauthorized client devices from gaining access to the network.

This chapter includes the following major sections:

•Understanding 802.1X Port-Based Authentication

•Configuring 802.1X

•Displaying 802.1X Statistics and Status

Note For complete syntax and usage information for the switch commands used in this chapter, refer to the Catalyst 4500 Series Switch Cisco IOS Command Reference and related publications at this location:

http://www.cisco.com/en/US/products/ps6350/index.html

Understanding 802.1X Port-Based Authentication

802.1X defines 802.1X port-based authentication as a client-server based access control and authentication protocol that restricts unauthorized clients from connecting to a LAN through publicly accessible ports. An authentication server validates each supplicant (client) connected to an authenticator (network access switch) port before making available any services offered by the switch or the LAN.

Note 802.1X support requires an authentication server that is configured for Remote Authentication Dial-In User Service (RADIUS). 802.1X authentication does not work unless the network access switch can route packets to the configured RADIUS server. To verify that the switch can route packets, you must ping the server from the switch.

Until a client is authenticated, only Extensible Authentication Protocol over LAN (EAPOL) traffic is allowed through the port to which the client is connected. After authentication succeeds, normal traffic can pass through the port.

To configure 802.1X port-based authentication, you need to understand the concepts in these sections:

•Device Roles

•802.1X and Network Access Control

•Authentication Initiation and Message Exchange

•Ports in Authorized and Unauthorized States

•802.1X Host Mode

•Using 802.1X with VLAN Assignment

•Using 802.1X for Guest VLANs

•Using 802.1X with MAC Authentication Bypass

•Using 802.1X with Inaccessible Authentication Bypass

•Using 802.1X with Unidirectional Controlled Port

•Using 802.1X with Authentication Failed VLAN Assignment

•Using 802.1X with Port Security

•Using 802.1X with RADIUS-Provided Session Timeouts

•Using 802.1X with RADIUS Accounting

•Using 802.1X with Voice VLAN Ports

•Using Multiple Domain Authentication

•Supported Topologies

Device Roles

With 802.1X port-based authentication, network devices have specific roles. Figure 34-1 shows the role of each device, which is described below.

Figure 34-1 802.1X Device Roles

•Client—The workstation that requests access to the LAN, and responds to requests from the switch. The workstation must be running 802.1X-compliant client software.

Note For more information on 802.1X-compliant client application software such as Microsoft Windows 2000 Professional or Windows XP, refer to the Microsoft Knowledge Base article at this URL: http://support.microsoft.com

•Authenticator—Controls physical access to the network based on the authentication status of the client. The Catalyst 4500 series switch acts as an intermediary between the client and the authentication server, requesting identity information from the client, verifying that information with the authentication server, and relaying a response to the client. The switch encapsulates and decapsulates the Extensible Authentication Protocol (EAP) frames and interacts with the RADIUS authentication server.

When the switch receives EAPOL frames and relays them to the authentication server, the Ethernet header is stripped and the remaining EAP frame is reencapsulated in the RADIUS format. The EAP frames are not modified or examined during encapsulation, and the authentication server must support EAP within the native frame format. When the switch receives frames from the authentication server, the frame header is removed from the server, leaving the EAP frame, which is then encapsulated for Ethernet and sent to the client.

Note The Catalyst 4500 series switches must be running software that supports the RADIUS client and 802.1X.

•Authentication server—Performs the actual authentication of the client. The authentication server validates the identity of the client and notifies the switch that the client is authorized to access the LAN and switch services. (The only supported authentication server is the RADIUS authentication server with EAP extensions; it is available in Cisco Secure Access Control Server version 3.2 and later.)

802.1X and Network Access Control

Network Access Control is a feature that allows port access policies to be influenced by the anti-virus posture of the authenticating device.

Anti-virus posture includes such elements as the operating system running on the device, the operating system version, whether anti-virus software is installed, what version of anti-virus signatures is available, etc. If the authenticating device has a NAC-aware 802.1X supplicant and the authentication server is configured to support NAC via 802.1X, anti-virus posture information is automatically included as part of the 802.1X authentication exchange.

For information on NAC, refer to the URL:

http://www.cisco.com/en/US/products/ps6128/index.html

Authentication Initiation and Message Exchange

The switch or the client can initiate authentication. If you enable authentication on a port with the
dot1x port-control auto interface configuration command, the switch must initiate authentication when it determines that the port link state has changed. It then sends an EAP-request/identity frame to the client to request its identity (typically, the switch sends an initial identity/request frame followed by one or more requests for authentication information). Upon receipt of the frame, the client responds with an EAP-response/identity frame.

However, if during bootup, the client does not receive an EAP-request/identity frame from the switch, the client can initiate authentication by sending an EAPOL-start frame, which prompts the switch to request the client's identity.

If 802.1X is not enabled or supported on the network access switch, any EAPOL frames from the client are dropped. If the client does not receive an EAP-request/identity frame after three attempts to start authentication, the client transmits frames as if the port is in the authorized state. A port in the authorized state means that the client has been successfully authenticated. When the client supplies its identity, the switch begins its role as the intermediary, passing EAP frames between the client and the authentication server until authentication succeeds or fails. If the authentication succeeds, the switch port becomes authorized.

The specific exchange of EAP frames depends on the authentication method being used. Figure 34-2 shows a message exchange that is initiated by the client using the One-Time Password (OTP) authentication method with an authentication server.

Figure 34-2 Message Exchange

Ports in Authorized and Unauthorized States

The switch port state determines whether or not the client is granted access to the network. The port starts in the unauthorized state. While in this state, the port disallows all ingress and egress traffic except for 802.1X protocol packets. When a client is successfully authenticated, the port transitions to the authorized state, allowing all traffic for the client to flow normally.

If a non-802.1X capable client is connected to an unauthorized 802.1X port, the switch requests the client's identity. In this situation, the client does not respond to the request, the port remains in the unauthorized state, and the client is not granted access to the network. If a guest VLAN is configured on a port that connects to a client that does not support 802.1X, the port is placed in the configured guest VLAN and in the authorized state. For more information, see the "Using 802.1X for Guest VLANs" section.

In contrast, when an 802.1X-enabled client connects to a port that is not running the 802.1X protocol, the client initiates the authentication process by sending the EAPOL-start frame. When no response is received, the client sends the request a fixed number of times. Because no response is received, the client begins sending frames as if the port is in the authorized state.

You can control the port authorization state with the dot1x port-control interface configuration command and these keywords:

•force-authorized—Disables 802.1X authentication and causes the port to transition to the authorized state without requiring authentication exchange. The port transmits and receives normal traffic without 802.1X-based authentication of the client. This setting is the default.

•force-unauthorized—Causes the port to remain in the unauthorized state, ignoring all attempts by the client to authenticate. The switch cannot provide authentication services to the client through the interface.

•auto—Enables 802.1X authentication and causes the port to begin in the unauthorized state, allowing only EAPOL frames to be sent and received through the port. The authentication process begins when the link state of the port transitions from down to up or when an EAPOL-start frame is received. The switch requests the identity of the client and begins relaying authentication messages between the client and the authentication server. The switch can uniquely identify each client attempting to access the network by the client's MAC address.

If the client is successfully authenticated (receives an Accept frame from the authentication server), the port state changes to authorized, and all frames from the authenticated client are allowed through the port. If authentication fails, the port remains in the unauthorized state, but authentication can be retried. If the authentication server cannot be reached, the switch can retransmit the request. If no response is received from the server after the specified number of attempts, authentication fails and network access is not granted.

If the link state of a port transitions from up to down, or if an EAPOL-logoff frame is received by the port, the port returns to the unauthorized state.

Figure 34-3 shows the authentication process.

If Multidomain Authentication (MDA) is enabled on a port, this flow can be used with some exceptions that are applicable to voice authorization. For more information on MDA, see "Using Multiple Domain Authentication" section.

Note Supervisor Engine 6-E does not support MDA.

Figure 34-3 Authentication Flowchart

802.1X Host Mode

You can configure an 802.1X port for single-host or multiple-hosts mode. In single-host mode (see Figure 34-1), only one client can be connected to the 802.1X-enabled switch port. The switch detects the client by sending an EAPOL frame when the port link state changes to the up state. If a client leaves or is replaced with another client, the switch changes the port link state to down, and the port returns to the unauthorized state.

In multiple-hosts mode, you can attach multiple hosts to a single 802.1X-enabled port. Figure 34-4 shows 802.1X port-based authentication in a wireless LAN. In this mode, only one of the attached clients must be authorized for all clients to be granted network access. If the port becomes unauthorized (re-authentication fails or an EAPOL-logoff message is received), the switch denies network access to all of the attached clients. In this topology, the wireless access point is responsible for authenticating the clients attached to it, and it also acts as a client to the switch.

With multiple-hosts mode enabled, you can use 802.1X authentication to authenticate the port and port security to manage network access for all MAC addresses, including that of the client.

Figure 34-4 Multiple Host Mode Example

Cisco IOS Release 12.2(37)SG and later releases support Multi-Domain Authentication (MDA), which allows both a data device and a voice device, such as an IP Phone (Cisco or non-Cisco), to connect to the same switch port. For details on how to configure MDA, see the "Using Multiple Domain Authentication" section.

Using 802.1X with VLAN Assignment

You can use the VLAN assignment to limit network access for certain users. With the VLAN assignment, 802.1X-authenticated ports are assigned to a VLAN based on the username of the client connected to that port. The RADIUS server database maintains the username-to-VLAN mappings. After successful 802.1X authentication of the port, the RADIUS server sends the VLAN assignment to the switch. The VLAN can be a "standard" VLAN or a PVLAN.

On platforms that support PVLANs, you can isolate hosts by assigning ports into PVLANs.

When configured on the switch and the RADIUS server, 802.1X with VLAN assignment has these characteristics:

•If no VLAN is supplied by the RADIUS server, the port is configured in its access VLAN or isolated PVLAN when authentication succeeds.

•If the authentication server provides invalid VLAN information, the port remains unauthorized. This situation prevents ports from appearing unexpectedly in an inappropriate VLAN due to a configuration error.

•If the authentication server provides valid VLAN information, the port is authorized and placed in the specified VLAN when authentication succeeds.

•If the multiple-hosts mode is enabled, all hosts are in the same VLAN as the first authenticated user.

•If 802.1X is disabled on the port, the port is returned to the configured access VLAN.

•A port must be configured as an access port (which can be assigned only into "regular" VLANs), or as a PVLAN host port (which can be assigned only into PVLANs). Configuring a port as a PVLAN host port implies that all hosts on the port are assigned into PVLANs, whether their posture is compliant or non-compliant. If the type of the VLAN named in the Access-Accept does not match the type of VLAN expected to be assigned to the port (regular VLAN to access port, secondary private VLAN to private VLAN host port), the VLAN assignment fails.

•If a guest VLAN is configured to handle non-responsive hosts, the type of VLAN configured as the guest VLAN must match the port type (that is, guest VLANs configured on access ports must be standard VLANs, and guest VLANs configured on PVLAN host ports must be PVLANs. If the guest VLAN's type does not match the port type, non-responsive hosts are treated as if no guest VLAN is configured (that is, they are denied network access).

•To assign a port into a PVLAN, the named VLAN must be a secondary PVLAN. The switch determines the implied primary VLAN from the locally configured secondary-primary association.

Note If you change the access VLAN or PVLAN host VLAN mapping on a port that is already authorized in a RADIUS assigned VLAN, the port remains in the RADIUS assigned VLAN.

To configure VLAN assignment you need to perform these tasks:

•Enable AAA authorization with the network keyword to allow interface configuration from the RADIUS server. For an illustration of how to apply the aaa authorization network group radius command, refer to the section "Enabling 802.1X Authentication" on page 23.

•Enable 802.1X. (The VLAN assignment feature is automatically enabled when you configure 802.1X on an access port.)

•Assign vendor-specific tunnel attributes in the RADIUS server. To ensure proper VLAN assignment, the RADIUS server must return these attributes to the switch:

–Tunnel-Type = VLAN

–Tunnel-Medium-Type = 802

–Tunnel-Private-Group-ID = VLAN NAME

Using 802.1X for Guest VLANs

Note Supervisor Engine 6-E does not support this feature.

You can use guest VLANs to enable non-802.1X-capable hosts to access networks that use 802.1X authentication. For example, you can use guest VLANs while you are upgrading your system to support 802.1X authentication.

Guest VLANs are supported on a per-port basis, and you can use any VLAN as a guest VLAN as long as its type matches the type of the port. If a port is already forwarding on the guest VLAN and you enable 802.1X support on the network interface of the host, the port is immediately moved out of the guest VLAN and the authenticator waits for authentication to occur.

Enabling 802.1X authentication on a port starts the 802.1X protocol. If the host fails to respond to packets from the authenticator within a certain amount of time, the authenticator brings the port up in the configured guest VLAN.

If the port is configured as a PVLAN host port, the guest VLAN must be a secondary PVLAN. If the port is configured as an access port, the guest VLAN must be a regular VLAN. If the guest VLAN configured on a port is not appropriate for the type of the port, the switch behaves as if no guest VLAN is configured (that is, non-responsive hosts are denied network access).

For details on how to configure guest VLANs, see the "Configuring 802.1X with Guest VLANs" section.

Usage Guidelines for Using 802.1X Authentication with Guest VLANs

The usage guidelines for using 802.1X authentication with guest VLANs are as follows:

•When you reconfigure a guest VLAN to a different VLAN, any authentication failed ports are also moved and the ports stay in their current authorized state.

•When you shut down or remove a guest VLAN from the VLAN database, any authentication failed ports are immediately moved to an unauthorized state and the authentication process is restarted.

Note No periodic reauthentication is allowed with guest VLANs.

Usage Guidelines for Using 802.1X Authentication with Guest VLANs on Windows-XP Hosts

The usage guidelines for using 802.1X authentication with guest VLANs on Windows-XP hosts are as follows:

•If the host fails to respond to the authenticator, the port attempts to connect three times (with a 30 second timeout between each attempt). After this time, the login/password window does not appear on the host, so you must unplug and reconnect the network interface cable.

•Hosts responding with an incorrect login/password fail authentication. Hosts failing authentication are not put in the guest VLAN. The first time that a host fails authentication, the quiet-period timer starts, and no activity occurs for the duration of the quiet-period timer. When the quiet-period timer expires, the host is presented with the login/password window. If the host fails authentication for the second time, the quiet-period timer starts again, and no activity occurs for the duration of the quiet-period timer. The host is presented with the login/password window a third time. If the host fails authentication the third time, the port is placed in the unauthorized state, and you must disconnect and reconnect the network interface cable.

Using 802.1X with MAC Authentication Bypass

Note Supervisor Engine 6-E does not support this feature.

The 802.1X protocol has 3 entities: client (supplicant), authenticator, and authentication server. Typically, the host PC runs the supplicant software and tries to authenticate itself by sending its credentials to the authenticator which in turn relays that info to the authentication server for authentication.

However, not all hosts may have supplicant functionality. Devices that cannot authenticate themselves using 802.1X , which still should have network access, can use MAC Authentication Bypass (MAB), which uses the connecting device's MAC address to grant/deny network access.

Typically, you would use this feature on ports where devices such as printers are connected. Such devices do not have 802.1X supplicant functionality.

In a typical deployment, the RADIUS server maintains a database of MAC addresses that require access. When this feature detects a new MAC address on a port, it generates a RADIUS request with both username and password as the device's MAC address. After authorization succeeds, the port is accessible to the particular device through the same code path that 802.1X authentication would take when processing an 802.1X supplicant. If authentication fails, the port moves to the guest VLAN if configured, or it remains unauthorized.

The Catalyst 4500 series switch also supports re-authentication of MACs on a per port level. Be aware that the re-authentication functionality is provided by 802.1X and is not MAB specific. In the re-authentication mode, a port stays in the previous RADIUS-sent VLAN and tries to re-authenticate itself. If the re-authentication succeeds, the port stays in the RADIUS-sent VLAN. Otherwise, the port becomes unauthorized and moves to the guest VLAN if one is configured.

For details on how to configure MAB, see the "Configuring 802.1X with MAC Authentication Bypass" section.

Feature Interaction

This section lists feature interactions and restrictions when MAB is enabled. If a feature is not listed, assume that it interacts seamlessly with MAB (such as Unidirectional Controlled Port).

•MAB can only be enabled if 802.1X is configured on a port. MAB functions as a fall back mechanism for authorizing MACs. If you configure both MAB and 802.1X on a port, the port attempts to authenticate using 802.1X. If the host fails to respond to EAPOL requests and MAB is configured, the 802.1X port is opened up to listen to packets and to grab a MAC address, rather than attempt to authenticate endlessly.

Based on the default 802.1X timer values, the transition between mechanisms takes approximately 90 seconds. You can shorten the time by reducing the value of the transmission period time, which affects the frequency of EAPOL transmission. A smaller timer value results in EAPOLs sent during a shorter period of time. With MAB enabled, after 802.1X performs one full set of EAPOLs, the learned MAC address is forwarded to the authentication server for processing.

The MAB module performs authorization for the first MAC address detected on the wire. The port is considered authorized once a valid MAC address is received that RADIUS approves of.

802.1X authentication can re-start if an EAPOL packet is received on a port that was initially authorized as a result of MAB.

Figure 34-5 shows the message exchange during MAB.

Figure 34-5 Message Exchange during MAC Authentication Bypass

•The authentication-failed VLAN is used only with dot1x-authentication-failed users. MAB is not attempted with dot1x-authentication-failed users. If 802.1X authentication fails, a port moves to the authentication-failed VLAN (if configured) whether MAB is configured or not.

•When both MAB and guest VLAN are configured and no EAPOL packets are received on a port, the 802.1X state-machine is moved to a MAB state where it opens the port to listen to traffic and grab MAC addresses. The port remains in this state forever waiting to see a MAC on the port. A detected MAC address that fails authorization causes the port to be moved to the guest VLAN if configured.

While in a guest VLAN, a port is open to all traffic on the specified guest VLAN. Therefore, non-802.1X supplicants that normally would be authorized but are in guest VLAN due to the earlier detection of a device that failed authorization, would remain in the guest VLAN indefinitely. However, loss of link or the detection of an EAPOL on the wire causes a transition out of the guest VLAN and back to the default 802.1X mode.

•Once a new MAC has been authenticated by MAB, the responsibility to limit access falls upon the 802.1X Authenticator (or port security) to secure the port. The 802.1X default host parameter is defined only for a single host. If the port is changed to multi-user host, port security must be employed to enforce the number of MAC addresses allowed thru this port.

•Catalyst 4500 series switch supports MAB with VVID, with the restriction that the MAC address appears on a port data VLAN only. All IP phone MACs learned via CDP are allowed on voice VLANs.

•MAB and VMPS are mutually exclusive because their functionality overlaps.

Using 802.1X with Inaccessible Authentication Bypass

Note Supervisor Engine 6-E does not support this feature.

When a switch cannot reach the configured RADIUS servers and clients (supplicants) cannot be authenticated, you can configure a switch to allow network access to hosts connected to critical ports that are enabled for Inaccessible Authentication Bypass.

When this feature is enabled, a switch monitors the status of the configured RADIUS servers. If no RADIUS servers are available, ports with Inaccessible Authentication Bypass enabled are authorized. You can specify a Inaccessible Authentication Bypass VLAN on a per-port basis.

Ports that were already authorized when RADIUS becomes unavailable are unaffected by Inaccessible Authentication Bypass. However, if re-authentication is applied and RADIUS is not restored by the next polling cycle, ports already authorized falls back to the critical auth VLAN.

When RADIUS becomes available, critically-authorized ports may be configured to automatically reauthenticate themselves.

For details on how to configure Inaccessible Authentication Bypass, see the "Configuring 802.1X with Inaccessible Authentication Bypass" section.

Using 802.1X with Unidirectional Controlled Port

Note Supervisor Engine 6-E does not support this feature.

Unidirectional Controlled Port is a combined hardware/software feature that allows dormant PCs to be "powered on" based on the receipt of a specific Ethernet frame, known as the magic packet. Generally, Unidirectional Controlled Port is used in environments where administrators plan to manage remote systems during off-hours, when it's likely that the systems have been powered down.

Use of Unidirectional Controlled Port with hosts attached through 802.1X ports presents a unique problem; when the host powers down, a 802.1X port becomes unauthorized. In this state, the port allows the receipt and transmission of EAPoL packets only. Therefore, the Unidirectional Controlled Port magic packet cannot reach the host; without powering up, the PC cannot authenticate and open the port.

Unidirectional Controlled Port solves this problem by allowing packets to be transmitted on unauthorized 802.1X ports.

Note Unidirectional Controlled Port only works when Spanning Tree Portfast is enabled on the port.

For details on how to configure 802.1X with Unidirectional Controlled Port, see the "Configuring 802.1X with Unidirectional Controlled Port" section

Unidirectional State

When you configure a port as unidirectional with the dot1x control-direction in interface configuration command, the port changes to the spanning-tree forwarding state.

When Unidirectional Controlled Port is enabled, the connected host is in the sleeping mode or power-down state. The host does not exchange traffic with other devices in the network. If the host connected to the unidirectional port that cannot send traffic to the network, the host can only receive traffic from other devices in the network.

Bidirectional State

When you configure a port as bidirectional with the dot1x control-direction both interface configuration command, the port is access-controlled in both directions. In this state, except EAPOL packets, the switch port does not receive or send packets.

Using 802.1X with Authentication Failed VLAN Assignment

Note Supervisor Engine 6-E does not support this feature.

You can use authentication-failed VLAN assignment on a per-port basis to provide access for authentication failed users. Authentication failed users are end hosts that are 802.1X- capable but do not have valid credentials in an authentication server or end hosts that do not give any username and password combination in the authentication pop-up window on the user side.

If a user fails the authentication process, that port is placed in the authentication-failed VLAN. The port remains in the authentication-failed VLAN until the reauthentication timer expires. When the reauthentication timer expires the switch starts sending the port re-authentication requests. If the port fails reauthentication it remains in the authentication-failed VLAN. If the port is successfully reauthenticated, the port is moved either to the VLAN sent by RADIUS server or to the newly authenticated ports configured VLAN; the location depends on whether RADIUS is configured to send VLAN information.

Note When enabling periodic reauthentication (see the "Enabling Periodic Reauthentication" section), only local reauthentication timer values are allowed. You cannot utilize a RADIUS server to assign the reauthentication timer value.

You can set the maximum number of authentication attempts that the authenticator sends before moving a port into the authentication-failed VLAN. The authenticator keeps a count of the failed authentication attempts for each port. A failed authentication attempt is either an empty response or an EAP failure. The authenticator tracks any mix of failed authentication attempts towards the authentication attempt count. After the maximum number of attempts is reached the port is placed in the authentication-failed VLAN until the reauthentication timer expires again.

Note RADIUS may send a response without an EAP packet in it when it does not support EAP, and sometimes third party RADIUS servers also send empty responses. When this happens, the authentication attempt counter is incremented.

For details on how to configure Authentication Failed VLAN Assignment, see the "Configuring 802.1X with Authentication Failed VLAN Assignment" section.

Usage Guidelines for Using Authentication Failed VLAN Assignment

•You should enable reauthentication. The ports in authentication-failed VLANs do not receive reauthentication attempts if reauthentication is disabled. In order to start the reauthentication process the authentication-failed VLAN must receive a link down event or an EAP logoff event from the port. If the host is behind a hub, you may never get a link down event and may not detect the new host until the next reauthentication occurs. Therefore, it is recommended to have re-authentication enabled in that case.

•EAP failure messages are not sent to the user. If the user failures authentication the port is moved to an authentication-failed VLAN and a EAP success message is sent to the user. Because the user is not notified of the authentication failure there may be confusion as to why there is restricted access to the network. A EAP Success message is sent for the following reasons:

–If the EAP Success message is not sent, the user tries to authenticate every 60 seconds (by default) by sending an EAP-start message.

–In some cases, users have configured DHCP to EAP-Success and unless the user sees a success, DHCP does not work on the port.

•Sometimes a user caches an incorrect username and password combination after receiving a EAP success message from the authenticator and reuses that information in every re-authentication. Until the user passes the correct username and password combination the port remains in the authentication-failed VLAN.

•When an authentication failed port is moved to an unauthorized state the authentication process is restarted. If you should fail the authentication process again the authenticator waits in the held state. After you have correctly reauthenticated all 802.1X ports are reinitialized and treated as normal 802.1X ports.

•When you reconfigure an authentication-failed VLAN to a different VLAN, any authentication failed ports are also moved and the ports stay in their current authorized state.

•When you shut down or remove an authentication-failed VLAN from the VLAN database, any authentication failed ports are immediately moved to an unauthorized state and the authentication process is restarted. The authenticator does not wait in a held state because the authentication-failed VLAN configuration still exists. While the authentication-failed VLAN is inactive, all authentication attempts are counted, and as soon as the VLAN becomes active the port is placed in the authentication-failed VLAN.

•If you reconfigure the maximum number of authentication failures allowed by the VLAN, the change takes affect after the reauthentication timer expires.

•All internal VLANs which are used for Layer 3 ports cannot be configured as an authentication-failed VLAN.

•The authentication-failed VLAN is supported only in single-host mode (the default port mode).

•When a port is placed in an authentication-failed VLAN the user's MAC address is added to the mac-address-table. If a new MAC address appears on the port, it is treated as a security violation.

•When an authentication failed port is moved to an authentication-failed VLAN, the Catalyst 4500 series switch does not transmit a RADIUS-Account Start Message like it does for regular 802.1X authentication.

Using 802.1X with Port Security

You can enable port security on an 802.1X port in either single- or multiple-host mode. (To do so, you must configure port security with the switchport port-security interface configuration command. Refer to the nb chapter in this guide.) When you enable port security and 802.1X on a port, 802.1X authenticates the port, and port security manages the number of MAC addresses allowed on that port, including that of the client. Hence, you can use an 802.1X port with port security enabled to limit the number or group of clients that can access the network.

For information on selecting multi-host mode, see the "Resetting the 802.1X Configuration to the Default Values" section.

These examples describe the interaction between 802.1X and port security on a switch:

•When a client is authenticated, and the port security table is not full, the client's MAC address is added to the port security list of secure hosts. The port then proceeds to come up normally.

When a client is authenticated and manually configured for port security, it is guaranteed an entry in the secure host table (unless port security static aging has been enabled).

A security violation occurs if an additional host is learned on the port. The action taken depends on which feature (802.1X or port security) detects the security violation:

–If 802.1X detects the violation, the action is to err-disable the port.

–If port security detects the violation, the action is to shutdown or restrict the port (the action is configurable).

The following describes when port security and 802.1X security violations occur:

–In single host mode, after the port is authorized, any MAC address received other than the client's causes a 802.1X security violation.

–In single host mode, if installation of an 802.1X client's MAC address fails because port security has already reached its limit (due to a configured secure MAC addresses), a port security violation is triggered.

–In multi host mode, once the port is authorized, any additional MAC addresses that cannot be installed because the port security has reached its limit triggers a port security violation.

•When an 802.1X client logs off, the port transitions back to an unauthenticated state, and all dynamic entries in the secure host table are cleared, including the entry for the client. Normal authentication then ensues.

•If you administratively shut down the port, the port becomes unauthenticated, and all dynamic entries are removed from the secure host table.

•Only 802.1X can remove the client's MAC address from the port security table. Note that in multi host mode, with the exception of the client's MAC address, all MAC addresses that are learned by port security can be deleted using port security CLIs.

•Whenever port security ages out a 802.1X client's MAC address, 802.1X attempts to reauthenticate the client. Only if the reauthentication succeeds is the client's MAC address be retained in the port security table.

•All of the 802.1X client's MAC addresses are tagged with (dot1x) when you display the port security table by using CLI.

Using 802.1X with RADIUS-Provided Session Timeouts

You can specify whether a switch uses a locally configured or a RADIUS-provided reauthentication timeout. If the switch is configured to use the local timeout, it reauthenticates the host when the timer expires.

If the switch is configured to use the RADIUS-provided timeout, it looks in the RADIUS Access-Accept message for the Session-Timeout and optional Termination-Action attributes. The switch uses the value of the Session-Timeout attribute to determine the duration of the session, and it uses the value of the Termination-Action attribute to determine the switch action when the session's timer expires.

If the Termination-Action attribute is present and its value is RADIUS-Request, the switch reauthenticates the host. If the Termination-Action attribute is not present, or its value is Default, the switch terminates the session.

Note The supplicant on the port detects that its session has been terminated and attempts to initiate a new session. Unless the authentication server treats this new session differently, the client may see only a brief interruption in network connectivity as the switch sets up a new session.

If the switch is configured to use the RADIUS-supplied timeout, but the Access-Accept message does not include a Session-Timeout attribute, the switch never reauthenticates the supplicant. This behavior is consistent with Cisco's wireless access points.

For details on how to configure RADIUS-provided session timeouts, see the "Configuring RADIUS-Provided Session Timeouts" section.

Using 802.1X with RADIUS Accounting

Note Supervisor Engine 6-E does not support this feature.

Note If you plan to implement system-wide accounting, you should also configure 802.1X accounting. Moreover, you need to inform the accounting server of the system reload event when the system is reloaded. Doing this ensures that the accounting server is aware that all outstanding 802.1X sessions on this system are closed.

Note To enable 802.1X accounting, you must first configure 802.1X authentication and switch-to-RADIUS server communication.

802.1X RADIUS accounting relays important events to the RADIUS server (such as the client's connection session). This session is defined as the interval beginning when the client is authorized to use the port and ending when the client stops using the port.

Figure 34-6 illustrates the RADIUS accounting process.

Figure 34-6 RADIUS Accounting

After the client is authenticated, the switch sends accounting-request packets to the RADIUS server, which responds with accounting-response packets to acknowledge the receipt of the request.

A RADIUS accounting-request packet contains one or more Attribute-Value pairs to report various events and related information to the RADIUS server. The following events are tracked:

•User successfully authenticates

•User logs-off

•Link-down occurs on a 802.1X port

•Reauthentication succeeds

•Reauthentication fails

When the port state transitions between authorized and unauthorized, the RADIUS messages are transmitted to the RADIUS server.

The switch does not log any accounting information. Instead, it sends such information to the RADIUS server, which must be configured to log accounting messages.

The 802.1X authentication, authorization and accounting process is as follows:

Step 1 A user connects to a port on the switch.

Step 2 Authentication is performed, for example, using the username/password method.

Step 3 VLAN assignment is enabled, as appropriate, per RADIUS server configuration.

Step 4 The switch sends a start message to an accounting server.

Step 5 Reauthentication is performed, as necessary.

Step 6 The switch sends an interim accounting update to the accounting server that is based on the result of reauthentication.

Step 7 The user disconnects from the port.

Step 8 The switch sends a stop message to the accounting server.

To configure 802.1X accounting, you need to do the following tasks:

•Enable logging of "Update/Watchdog packets from this AAA client" in your RADIUS server's Network Configuration tab.

•Enable "Logging>CVS RADIUS Accounting" in your RADIUS server System Configuration tab.

•Enable 802.1X accounting on your switch.

•Enable AAA accounting by using the aaa system accounting command. Refer to the "Enabling 802.1X RADIUS Accounting" section.

Enabling AAA system accounting along with 802.1X accounting allows system reload events to be sent to the accounting RADIUS server for logging. By doing this, the accounting RADIUS server can infer that all active 802.1X sessions are appropriately closed.

Because RADIUS uses the unreliable transport protocol UDP, accounting messages may be lost due to poor network conditions. If the switch does not receive the accounting response message from the RADIUS server after a configurable number of retransmissions of an accounting request, the following system message appears:

Accounting message %s for session %s failed to receive Accounting Response.

When the stop message is not transmitted successfully, a message like the following appears:

00:09:55: %RADIUS-3-NOACCOUNTINGRESPONSE: Accounting message Start for session 
172.20.50.145 sam 11/06/03 07:01:16 11000002 failed to receive Accounting Response.

Use the show radius statistics command to display the number of RADIUS messages that do not receive the accounting response message.

Using 802.1X with Voice VLAN Ports

Note Supervisor Engine 6-E does not support this feature.

A voice VLAN port is a special access port associated with two VLAN identifiers:

•Voice VLAN ID (VVID) to carry voice traffic to and from the IP phone. The VVID is used to configure the IP phone connected to the port.

•Port VLAN ID (PVID) to carry the data traffic to and from the workstation connected to the switch through the IP phone. The PVID is the native VLAN of the port.

Each port that you configure for a voice VLAN is associated with a VVID and a PVID. This configuration allows voice traffic and data traffic to be separated onto different VLANs.

A voice VLAN port becomes active when there is a link whether or not the port is AUTHORIZED or UNAUTHORIZED. All traffic coming through the voice VLAN is learned correctly and appears in the MAC-address-table. Cisco IP phones do not relay CDP messages from other devices. As a result, if several Cisco IP phones are connected in series, the switch recognizes only the one directly connected to it. When 802.1X is enabled on a voice VLAN port, the switch drops packets from unrecognized Cisco IP phones more than one hop away.

When 802.1X is enabled on a port, you cannot configure a PVID that is equal to a VVID. For more information about voice VLANs, see Chapter 33, "Configuring Voice Interfaces."

Be aware of the following feature interactions:

•802.1X VLAN assignment cannot assign to the port the same VLAN as the voice VLAN; otherwise, the 802.1X authentication fails.

•802.1X guest VLAN works with the 802.1X voice VLAN port feature. However, the guest VLAN cannot be the same as the voice VLAN.

•802.1X port security works with the 802.1X voice VLAN port feature and is configured per port. Two MAC addresses must be configured: one for the Cisco IP phone MAC address on the VVID and one for the PC MAC-address on PVID.

However, you cannot use the 802.1X voice VLAN port feature with 802.1X port security's sticky MAC address configuration and statically configured MAC address configuration.

•802.1X accounting is unaffected by the 802.1X voice VLAN port feature.

•When 802.1X is configured on a port, you cannot connect multiple IP-phones to a Catalyst 4500 series switch through a hub.

•Because voice VLANs cannot be configured as private VLAN host ports, and because only private VLANs can be assigned to private VLAN host ports, VLAN assignment cannot assign a private VLAN to a port with a voice VLAN configured.

For details on how to configure 802.1X with voice VLANs, see the "Configuring 802.1X with Voice VLAN" section.

Using Multiple Domain Authentication

Note Supervisor Engine 6-E does not support this feature.

Multiple Domain Authentication (MDA) allows both a data device and a voice device, such as an IP phone (Cisco or non-Cisco), to authenticate on the same switch port, which is divided into a data domain and a voice domain.

MDA does not enforce the order of device authentication. For best results, however, you should authenticate a voice device before you authenticate a data device on an MDA-enabled port.

Observe the following guidelines for configuring MDA:

•To configure a switch port for MDA, see the "Configuring Multiple Domain Authentication" section.

•You must configure the voice VLAN for the IP phone when the host mode is set to multidomain. For more information, see Chapter 33, "Configuring Voice Interfaces."

Note If you use a dynamic VLAN to assign a voice VLAN on an MDA-enabled switch port, the voice device fails authorization.

•To authorize a voice device, the AAA server must be configured to send a Cisco Attribute-Value (AV) pair attribute with a value of device-traffic-class=voice. Without this value, the switch treats the voice device as a data device.

•The guest VLAN and restricted VLAN features only apply to the data devices on an MDA-enabled port. The switch treats a voice device that fails authorization as a data device.

•If more than one device attempts authorization on either the voice or the data domain of a port, it is error disabled.

•Until a device is authorized, the port drops its traffic. Non-Cisco IP phones or voice devices are allowed into both the data and voice VLANs. The data VLAN allows the voice device to contact a DHCP server to obtain an IP address and acquire the voice VLAN information. After the voice device starts sending on the voice VLAN, its access to the data VLAN is blocked.

•You can use dynamic VLAN assignment from a RADIUS server only for data devices.

Note Supervisor Engine 6-E does not support dynamic VLAN.

•MDA can use MAC authentication bypass as a fallback mechanism to allow the switch port to connect to devices that do not support 802.1X authentication. This is especially useful for 3rd-party phones without 802.1X supplicant. For more information, see the "Using 802.1X with MAC Authentication Bypass" section.

•When a data or a voice device is detected on a port, its MAC address is blocked until authorization succeeds. If the authorization fails, the MAC address remains blocked for 5 minutes.

•If more than five devices are detected on the data VLAN or more than one voice device is detected on the voice VLAN while a port is unauthorized, the port is error disabled.

•When a port host mode is changed from single- or multihost to multidomain mode, an authorized data device remains authorized on the port. However, a Cisco IP phone that has been allowed on the port in the voice VLAN is automatically removed and must be reauthenticated on that port.

•Active fallback mechanisms such as guest VLAN and restricted VLAN remain configured after a port changes from single- or multihost mode to multidomain mode.

•Switching a port host mode from multidomain to single- or multihost mode removes all authorized devices from the port.

•If a data domain is authorized first and placed in the guest VLAN, non-802.1X-capable voice devices need to tag their packets on the voice VLAN to trigger authentication.

•We do not recommend per-user ACLs with an MDA-enabled port. An authorized device with a per-user ACL policy might impact traffic on both the voice and data VLANs of the port. If used, only one device on the port should enforce per-user ACLs.

Supported Topologies

The 802.1X port-based authentication supports two topologies:

•Point to point

•Wireless LAN

In a point-to-point configuration (see Figure 34-1), only one client can be connected to the 802.1X-enabled switch port when the multi-host mode is not enabled (the default). The switch detects the client when the port link state changes to the up state. If a client leaves or is replaced with another client, the switch changes the port link state to down, and the port returns to the unauthorized state.

For 802.1X port-based authentication in a wireless LAN (Figure 34-7), you must configure the 802.1X port as a multiple-host port that is authorized as a wireless access point once the client is authenticated. (See the "Resetting the 802.1X Configuration to the Default Values" section.) When the port is authorized, all other hosts that are indirectly attached to the port are granted access to the network. If the port becomes unauthorized (reauthentication fails or an EAPOL-logoff message is received), the switch denies access to the network for all wireless access point-attached clients. In this topology, the wireless access point is responsible for authenticating clients attached to it, and the wireless access point acts as a client to the switch.

Figure 34-7 Wireless LAN Example

Configuring 802.1X

To configure 802.1X, follow this procedure:

Step 1 Enable 802.1X authentication. See the "Enabling 802.1X Authentication" section.

Step 2 Configure switch to RADIUS server communication. See the "Configuring Switch-to-RADIUS-Server Communication" section.

Step 3 Adjust the 802.1X timer values. See the "Changing the Quiet Period" section.

Step 4 Configure optional features. See the "Configuring RADIUS-Provided Session Timeouts" section.

These sections describe how to configure 802.1X:

•Default 802.1X Configuration

•802.1X Configuration Guidelines

•Enabling 802.1X Authentication (required)

•Configuring Switch-to-RADIUS-Server Communication (required)

•Configuring Multiple Domain Authentication

•Configuring RADIUS-Provided Session Timeouts (optional)

•Enabling 802.1X RADIUS Accounting (optional)

•Configuring 802.1X with Guest VLANs (optional)

•Configuring 802.1X with MAC Authentication Bypass (optional)

•Configuring 802.1X with Inaccessible Authentication Bypass (optional)

•Configuring 802.1X with Unidirectional Controlled Port (optional)

•Configuring 802.1X with Authentication Failed VLAN Assignment (optional)

•Configuring 802.1X with Voice VLAN (optional)

•Enabling Periodic Reauthentication (optional)

•Enabling Multiple Hosts (optional

•Changing the Quiet Period (optional)

•Changing the Switch-to-Client Retransmission Time (optional)

•Setting the Switch-to-Client Frame-Retransmission Number (optional)

•Manually Reauthenticating a Client Connected to a Port (optional)

•Initializing the 802.1X Authentication State

•Removing 802.1X Client Information

•Resetting the 802.1X Configuration to the Default Values (optional)

Default 802.1X Configuration

Table 34-1 shows the default 802.1X configuration.

802.1X Configuration Guidelines

This section describes the guidelines for configuring 802.1X authentication:

•The 802.1X Protocol is supported only on Layer 2 static access, private VLAN host ports, and Layer 3 routed ports. You cannot configure 802.1X for any other port modes.

•If you are planning to use either 802.1X accounting or VLAN assignment, be aware that both features utilize general AAA commands. For information on how to configure AAA, refer to the "Enabling 802.1X Authentication" section. Alternatively, you can refer to the Cisco IOS security documentation:

–http://www.cisco.com/en/US/products/ps6586/products_ios_technology_home.html

Enabling 802.1X Authentication

To enable 802.1X port-based authentication, you first must enable 802.1X globally on your switch, then enable AAA and specify the authentication method list. A method list describes the sequence and authentication methods that must be queried to authenticate a user.

The software uses the first method listed in the method list to authenticate users; if that method fails to respond, the software selects the next authentication method in the list. This process continues until there is successful communication with a listed authentication method or until all defined methods are exhausted. If authentication fails at any point in this cycle, the authentication process stops, and no other authentication methods are attempted.

Note To allow VLAN assignment, you must enable AAA authorization to configure the switch for all network-related service requests.

To configure 802.1X port-based authentication, perform this task:

Switch# configure terminal

Switch(config)#  
dot1x system-auth-control

Switch(config)# aaa new-model

Switch(config)# aaa authentication 
dot1x {default} method1 [method2...]

Switch(config)# aaa authorization 
network {default} group radius

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch # show dot1x interface 
interface-id details

Switch# show running-config

Switch# copy running-config 
startup-config

Note Enabling Spanning Tree PortFast ensures that a port comes up immediately after authorization.

Note Whenever you configure any 802.1X parameter on a port, a dot1x authenticator is automatically created on the port. As a result dot1x pae authenticator appears in the configuration. This is to ensure that dot1x authentication still works on legacy configurations without manual intervention. This is likely to change in future releases.

This example shows how to enable 802.1X and AAA on Fast Ethernet port 2/1, and how to verify the configuration:

Switch# configure terminal

Switch(config)# dot1x system-auth-control

Switch(config)# aaa new-model

Switch(config)# aaa authentication dot1x default group radius

Switch(config)# interface fastethernet2/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch# show dot1x interface f7/1 details

Dot1x Info for FastEthernet7/1

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both 

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Dot1x Authenticator Client List

-------------------------------

Supplicant                = 1000.0000.2e00

        Auth SM State     = AUTHENTICATED

        Auth BEND SM Stat = IDLE

Port Status               = AUTHORIZED

Authentication Method     = Dot1x

Authorized By             = Authentication Server

Vlan Policy               = N/A

Configuring Switch-to-RADIUS-Server Communication

A RADIUS security server is identified by its host name or IP address, host name and specific UDP port number, or IP address and specific UDP port numbers. The combination of the IP address and UDP port number creates a unique identifier, which enables RADIUS requests to be sent to multiple UDP ports on a server at the same IP address. If two different host entries on the same RADIUS server are configured for the same service—for example, authentication—the second host entry configured acts as the fail-over backup to the first one. The RADIUS host entries are tried in the order they were configured.

To configure the RADIUS server parameters on the switch, perform this task:

Switch# configure terminal

Switch(config)# radius-server host 
{hostname | ip-address} auth-port 
port-number [acct-port port-number] 
[test username name] 
[ignore-auth-port] [ignore-acct-port] 
[idle-time min] key string

Switch(config-if)# radius deadtime 
min

Switch(config-if)# radius 
dead-criteria time seconds tries num

Switch(config-if)# ip radius 
source-interface m/p

Switch(config)# end

Switch# show running-config

Switch# copy running-config 
startup-config

This example shows how to specify the server with IP address 172.120.39.46 as the RADIUS server. The first command specifies port 1612 as the authorization port, sets the encryption key to rad123.

The second command dictates that key matches are performed on the RADIUS server:

Switch# configure terminal

Switch(config)# radius-server host 172.l20.39.46 auth-port 1612 key rad123

Switch(config)# ip radius source-interface m/p

Switch(config)# end

Switch#

You can globally configure the timeout, retransmission, and encryption key values for all RADIUS servers by using the radius-server host global configuration command. If you want to configure these options on a per-server basis, use the radius-server timeout, radius-server retransmit, and the radius-server key global configuration commands.

You also need to configure some settings on the RADIUS server. These settings include the IP address of the switch and the key string to be shared by both the server and the switch.

Configuring Multiple Domain Authentication

To configure MDA, perform these steps.

Switch# configure terminal

Switch(config)# radius-server vsa 
send authentication 

Switch(config)# interface 
interface-id

Switch(config-if)# [no] dot1x 
host-mode {single-host | multi-host 
| multi-domain}

Switch(config-if)# switchport voice 
vlan vlan-id

Switch(config-if)# end

Switch# show dot1x interface 
interface-id [detail]

Switch# copy running-config 
startup-config

This example shows how to enable 802.1X authentication and to allow multiple hosts:

Switch(config)# interface gigabitethernet2/1

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x host-mode multi-host

Switch(config-if)# end

This example shows how to enable MDA and to allow both a host and a 802.1X voice device (e.g., a Cisco or 3rd-party phone with 802.1X supplicant) on the port:

Switch# conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface FastEthernet3/1

Switch(config-if)# shut

Switch(config-if)# switchport access vlan 12

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x host-mode multi-domain

Switch(config-if)# no shut

Switch(config-if)# end

This example shows how to enable MDA and to allow both a host and a non-802.1X voice device on the port:

Switch# conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)# interface FastEthernet3/1

Switch(config-if)# shut

Switch(config-if)# switchport access vlan 12

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x host-mode multi-domain

Switch(config-if)# dot1x mac-auth-bypass

Switch(config-if)# no shut

Switch(config-if)# end

This example shows how to verify the dot1x MDA settings on interface FastEthernet6/1:

Switch# show dot1x interface FastEthernet3/1 detail

Dot1x Info for FastEthernet3/1

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both

HostMode                  = MULTI_DOMAIN

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Dot1x Authenticator Client List

-------------------------------

Domain                    = DATA

Supplicant                = 0000.0000.ab01

        Auth SM State     = AUTHENTICATED

        Auth BEND SM Stat = IDLE

Port Status               = AUTHORIZED

Authentication Method     = Dot1x

Authorized By             = Authentication Server

Vlan Policy               = 12

Domain                    = VOICE

Supplicant                = 0060.b057.4687

        Auth SM State     = AUTHENTICATED

        Auth BEND SM Stat = IDLE

Port Status               = AUTHORIZED

Authentication Method     = Dot1x

Authorized By             = Authentication Server

Switch#

Configuring RADIUS-Provided Session Timeouts

You can configure the Catalyst 4500 series switch to use a RADIUS-provided reauthentication timeout.

To configure RADIUS-provided timeouts, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x timeout 
reauth-period {interface | server}

Switch(config-if)# end

Switch# show dot1x interface 
interface-id details

Switch # copy running-config 
startup-config

This example shows how to configure the switch to derive the re-authentication period from the server and to verify the configuration:

Switch# configure terminal

Switch(config)# interface f7/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x timeout reauth-period server

Switch(config-if)# end

Switch# show dot1x interface f7/1 det

Dot1x Info for FastEthernet7/11

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = FORCE_AUTHORIZED

ControlDirection          = Both 

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = (From Authentication Server)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Dot1x Authenticator Client List Empty

Port Status               = AUTHORIZED

Switch#

Enabling 802.1X RADIUS Accounting

Note Supervisor Engine 6-E does not support this feature.

To configure 802.1X accounting, perform this task:

Switch# configure terminal

Switch(config)# aaa accounting 
dot1x default start-stop group 
radius

Switch(config)# clock timezone  
PST -8

Switch(config)# clock 
calendar-valid

Switch(config)# aaa accounting 
system default start-stop group 
radius

Switch(config)# end

Switch# show running-config

Switch# copy running-config 
startup-config

This example shows how to specify the server with IP address 172.120.39.46 as the RADIUS server. The first command configures the RADIUS server, specifying port 1612 as the authorization port, 1813 as the UDP port for accounting, and rad123 as the encryption key:

Switch# configure terminal

Switch(config)# radius-server host 172.120.39.46 auth-port 1812 acct-port 1813 key rad123

Switch(config)# aaa accounting dot1x default start-stop group radius

Switch(config)# aaa accounting system default start-stop group radius

Switch(config)# end

Switch#

Note You must configure the RADIUS server to perform accounting tasks, such as logging start, stop, and interim-update messages and time stamps. To turn on these functions, enable logging of "Update/Watchdog packets from this AAA client" in your RADIUS server Network Configuration tab. Next, enable "CVS RADIUS Accounting" in your RADIUS server System Configuration tab.

Configuring 802.1X with Guest VLANs

Note Supervisor Engine 6-E does not support this feature.

You can configure a guest VLAN for each 802.1X port on the Catalyst 4500 series switch to provide limited services to clients, such as downloading the 802.1X client. These clients might be upgrading their system for 802.1X authentication, and some hosts, such as Windows 98 systems, might not be 802.1X-capable.

When you enable a guest VLAN on an 802.1X port, the Catalyst 4500 series switch assigns clients to a guest VLAN provided (1) the authentication server does not receive a response to its EAPOL request or identity frame, or (2) the EAPOL packets are not sent by the client.

Starting with Cisco IOS Release 12.2(25)EWA, the Catalyst 4500 series switch maintains the EAPOL packet history. If another EAPOL packet is detected on the interface during the lifetime of the link, network access is denied. The EAPOL history is reset upon loss of the link.

Any number of 802.1X-incapable clients are allowed access when the switch port is moved to the guest VLAN. If an 802.1X-capable client joins the same port on which the guest VLAN is configured, the port is put into the unauthorized state in the user-configured access VLAN, and authentication is restarted.

Guest VLANs are supported on 802.1X ports in single-host or multiple-hosts mode.

Note When a port is put into a guest VLAN, it is automatically placed into multihost mode, and an unlimited number of hosts can connect through the port. Changing the multihost configuration does not effect a port in a guest VLAN.

Note Except for an RSPAN VLAN or a voice VLAN, you can configure any active VLAN as an 802.1X guest VLAN.

To configure 802.1X with guest VLAN on a port, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x guest-vlan 
vlan-id

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch(config)# end

This example shows how to enable a regular VLAN 50 on Fast Ethernet 4/3 as a guest VLAN on a static access port:

Switch# configure terminal

Switch(config)# interface fa4/3

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x guest-vlan 50

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch#

This example shows how to enable a secondary private VLAN 100 as a guest VLAN on a private VLAN host port:

Switch# configure terminal

Switch(config)# interface fa4/3

Switch(config-if)# switchport mode private-vlan host

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x guest-vlan 100

Switch(config-if)# end

Switch#

To enable supplicants to be allowed into guest VLAN on a switch, perform this task:

Switch# configure terminal

Switch# dot1x guest-vlan supplicant

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x guest-vlan 
vlan-id

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch# show dot1x interface 
interface-id

Switch# copy running-config 
startup-config

This example shows how to enable the guest VLAN feature and to specify VLAN 5 as a guest VLAN:

Switch# configure terminal

Switch(config)# dot1x guest-vlan supplicant

Switch(config)# interface gigabitethernet0/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x guest-vlan 5

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch#

Configuring 802.1X with MAC Authentication Bypass

Note Supervisor Engine 6-E does not support this feature.

To enable MAB, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# dot1x 
mac-auth-bypass [eap]

Switch(config)# end

Switch# show dot1x interface 
interface-id details

Switch# copy running-config 
startup-config

Note Removing a 802.1X MAB configuration from a port does not impact the authorized/authenticated state of the port. If the port is in an unauthenticated state, it remains in that state. If the port is in an authenticated state because of MAB, the switch reverts to the 802.1X Authenticator. If the port was already authorized with a MAC address and the MAB configuration was removed, the port remains in an authorized state until re-authentication occurs. At that time, if an 802.1X supplicant is detected on the wire, the MAC address is removed.

This example shows how to enable MAB on Gigabit Ethernet interface 3/3 and to verify the configuration:

Switch# configure terminal

Switch(config)# interface gigabitethernet3/3

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x mac-auth-bypass

Switch(config-if)# end

Switch# show dot1x int g3/3 details

Dot1x Info for GigabitEthernet3/3

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both 

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 1

RateLimitPeriod           = 0

Mac-Auth-Bypass           = Enabled

Dot1x Authenticator Client List

-------------------------------

Supplicant                = 0000.0000.0001

 Auth SM State     = AUTHENTICATED

 Auth BEND SM Stat = IDLE

Port Status               = AUTHORIZED

Authentication Method     = MAB

Authorized By             = Authentication Server

Vlan Policy               = N/A

Switch#

Configuring 802.1X with Inaccessible Authentication Bypass

Note Supervisor Engine 6-E does not support this feature.

Caution You must configure the switch to monitor the state of the RADIUS server as described in the section Configuring Switch-to-RADIUS-Server Communication for Inaccessible Authentication Bypass to work properly. Specifically, you must configure the RADIUS test username, idle-time, deadtime and dead-criteria. Failure to do so results in the switch failing to detect that the RADIUS server has gone down, or prematurely marking a dead RADIUS server as alive again.

To configure a port as a critical port and to enable the Inaccessible Authentication Bypass feature, perform this task:

Switch# configure terminal

Switch(config)# dot1x critical 
eapol

Switch(config)# dot1x critical 
recovery delay msec

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# dot1x critical

Switch(config-if)# dot1x critical 
vlan vlan

Switch(config-if)# dot1x critical 
recovery action reinitialize

Switch(config)# end

Switch# show dot1x interface 
interface-id details

Switch# copy running-config 
startup-config

The following example shows a full configuration of 802.1X with Inaccessible Authentication Bypass, including required AAA and RADIUS configuration as specified in the "Enabling 802.1X Authentication" sectionand "Configuring Switch-to-RADIUS-Server Communication" section.

The RADIUS server configured is at IP address 10.1.2.3, using port 1812 for authentication and 1813 for accounting. The RADIUS secret key is mykey. The username used for the test server probes is randomuser. The test probes for both living and dead servers are generated once per minute. The interface FastEthernet 3/1 is configured to critically authenticate into VLAN 17 when AAA becomes unresponsive, and to reinitialize automatically when AAA becomes available again.

Switch# configure terminal

Switch(config)# aaa new-model

Switch(config)# aaa authentication dot1x default group radius

Switch(config)# dot1x system-auth-control

Switch(config)# radius-server host 10.1.2.3 auth-port 1812 acct-port 1813 test username 
randomuser idle-time 1 key mykey

Switch(config)# radius deadtime 1

Switch(config)# radius dead-criteria time 15 tries 3

Switch(config)# interface f3/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x critical

Switch(config-if)# dot1x critical vlan 17

Switch(config-if)# dot1x critical recovery action reinitialize

Switch(config-if)# end

Switch# show dot1x int fastethernet 3/1 det

Dot1x Info for FastEthernet3/1

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = Both

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Critical-Auth             = Enabled

Critical Recovery Action  = Reinitialize

Critical-Auth VLAN        = 17

Dot1x Authenticator Client List

-------------------------------

Supplicant                = 0000.0000.0001

Auth SM State     = AUTHENTICATING

Auth BEND SM Stat = RESPONSE

Port Status               = AUTHORIZED

Authentication Method     = Dot1x

Authorized By             = Critical-Auth

Operational HostMode      = SINGLE_HOST

Vlan Policy               = 17

Switch#

Configuring 802.1X with Unidirectional Controlled Port

Note Supervisor Engine 6-E does not support this feature.

To configure unidirectional controlled port, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access 
or 
Switch(config-if)# switchport mode 
private-vlan host

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x 
control-direction {in | both}

Switch(config)# end

Switch# show dot1x interface 
interface-id details

Switch# copy running-config 
startup-config

Note Unidirectional Controlled Port only works when Spanning Tree Portfast is enabled on the port.

When a device is enabled for unidirectional controlled port (also termed Wake On LAN), its interface stays up when the device sleeps. So, the port connected to the device displays as link up (connected). When you forward special packets to the port, the device wakes up.

This example shows how to enable unidirectional port control:

Switch# configure terminal

Switch(config)# interface gigabitethernet3/3

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x control-direction in

Switch(config-if)# end

Switch# show dot1x int g3/3

Dot1x Info for GigabitEthernet3/3

-----------------------------------

PAE                       = AUTHENTICATOR

PortControl               = AUTO

ControlDirection          = In (Inactive)

HostMode                  = SINGLE_HOST

ReAuthentication          = Disabled

QuietPeriod               = 60

ServerTimeout             = 30

SuppTimeout               = 30

ReAuthPeriod              = 3600 (Locally configured)

ReAuthMax                 = 2

MaxReq                    = 2

TxPeriod                  = 30

RateLimitPeriod           = 0

Switch#

Configuring 802.1X with Authentication Failed VLAN Assignment

Note Supervisor Engine 6-E does not support this feature.

By configuring authentication-failed VLAN alignment on any Layer 2 port on the Catalyst 4500 series switch, you can provide limited network services to clients that fail the authentication process.

Note You can use authentication-failed VLAN assignment with other security features, such as Dynamic ARP Inspection (DAI), Dynamic Host Configuration Protocol (DHCP) snooping, and IP Source Guard. Each of these features can be enabled and disabled independently on the authentication-failed VLAN.

To configure 802.1X with authentication-failed VLAN assignment, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# dot1x auth-fail 
vlan vlan-id

Switch(config-if)# dot1x auth-fail 
max-attempts max-attemtps

Switch(config-if)# end

Switch(config)# end

Switch# show dot1x interface 
interface-id details

Switch# copy running-config 
startup-config

This example shows how to enable a regular VLAN 40 on Fast Ethernet 4/3 as a authentication-failed VLAN on a static access port:

Switch# configure terminal

Switch(config)# interface gigabitethernet3/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x port-control auto

Switch(config-if)# dot1x auth-fail vlan 40

Switch(config-if)# dot1x auth-fail max-attempts 5

Switch(config-if)# end

Switch(config)# end

Switch# show dot1x all

Dot1x Info for interface GigabitEthernet3/1 

----------------------------------------------------

PortStatus        = AUTHORIZED(AUTH-FAIL-VLAN)

MaxReq            = 2 

MaxAuthReq        = 2 

HostMode          = Single(AUTH-FAIL-VLAN) 

PortControl       = Auto

QuietPeriod       = 60 Seconds 

Re-authentication = Disabled 

ReAuthPeriod      = 3600 Seconds

ServerTimeout     = 30 Seconds 

SuppTimeout       = 30 Seconds 

TxPeriod          = 30 Seconds 

Guest-Vlan        = 6 

Switch

Configuring 802.1X with Voice VLAN

Note Supervisor Engine 6-E does not support this feature.

Note You must configure 802.1X and voice VLAN at the same time.

To enable 802.1X with voice VLAN, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport 
access vlan vlan-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# switchport voice 
vlan vlan-id

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch(config)# end

Switch# show dot1x interface 
interface-id details

Switch# copy running-config 
startup-config

This example shows how to enable 802.1X with voice VLAN feature on Fast Ethernet interface 5/9:

Switch# configure terminal

Switch(config)# interface fastethernet5/9

Switch(config-if)# switchport access vlan 2

Switch(config-if)# switchport mode access

Switch(config-if)# switchport voice vlan 10

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch(config# end

Switch#

Enabling Periodic Reauthentication

You can enable periodic 802.1X client reauthentication and specify how often it occurs. If you do not specify a time value before enabling reauthentication, the interval between reauthentication attempts is 3600 seconds.

Automatic 802.1X client reauthentication is a per-interface setting and can be set for clients connected to individual ports. To manually reauthenticate the client connected to a specific port, see the "Changing the Quiet Period" section.

To enable periodic reauthentication of the client and to configure the number of seconds between reauthentication attempts, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x 
re-authentication

Switch(config-if)# dot1x timeout 
reauth-period {seconds | server}

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

This example shows how to enable periodic reauthentication and set the number of seconds between reauthentication attempts to 4000:

Switch# configure terminal

Switch(config)# interface fastethernet5/9

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x re-authentication

Switch(config-if)# dot1x timeout reauth-period 4000

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch#

Enabling Multiple Hosts

You can attach multiple hosts (clients) to a single 802.1X-enabled port as shown in Figure 34-7. In this mode, when the port is authorized, all other hosts that are indirectly attached to the port are granted access to the network. If the port becomes unauthorized (reauthentication fails or an EAPOL-logoff message is received), the switch denies access to the network for all wireless access point-attached clients.

To allow multiple hosts (clients) on an 802.1X-authorized port that has the dot1x port-control interface configuration command set to auto, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x host-mode 
multiple-hosts

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch# show dot1x all interface 
interface-id

Switch# copy running-config 
startup-config

This example shows how to enable 802.1X on Fast Ethernet interface 0/1 and to allow multiple hosts:

Switch# configure terminal

Switch(config)# interface fastethernet0/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x host-mode multiple-hosts

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch#

Changing the Quiet Period

When the switch cannot authenticate the client, the switch remains idle for a set period of time, and then tries again. The idle time is determined by the quiet-period value. A failed authentication of the client might occur because the client provided an invalid password. You can provide a faster response time to the user by entering a number smaller than the default.

To change the quiet period, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x timeout 
quiet-period seconds

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch# show dot1x all

Switch# copy running-config 
startup-config

This example shows how to set the quiet-period on the switch to 30 seconds:

Switch# configure terminal

Switch(config)# interface fastethernet0/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x timeout quiet-period 30

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch#

Changing the Switch-to-Client Retransmission Time

The client responds to the EAP-request/identity frame from the switch with an EAP-response/identity frame. If the switch does not receive this response, it waits a set period of time (known as the retransmission time) and then retransmits the frame.

Note You should change the default value of this command only to adjust for unusual circumstances, such as unreliable links or specific behavioral problems with certain clients and authentication servers.

To change the amount of time that the switch waits for client notification, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x timeout 
tx-period seconds

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch# show dot1x all

Switch# copy running-config 
startup-config

This example shows how to set the retransmission time to 60 seconds:

Switch# configure terminal

Switch(config)# interface fastethernet0/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x timeout tx-period 60

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch#

Setting the Switch-to-Client Frame-Retransmission Number

In addition to changing the switch-to-client retransmission times, you can change the number of times that the switch sends EAP-Request/Identity and other EAP-Request frames to the client before restarting the authentication process. The number of EAP-Request/Identity retransmissions is controlled by the dot1x max-reauth-req command; the number of retransmissions for other EAP-Request frames is controlled by the dot1x max-req command.

Note You should change the default values of these commands only to adjust for unusual circumstances such as unreliable links or specific behavioral problems with certain clients and authentication servers.

To set the switch-to-client frame-retransmission numbers, perform this task:

Switch# configure terminal

Switch(config)# interface 
interface-id

Switch(config-if)# switchport mode 
access

Switch(config-if)# dot1x pae 
authenticator

Switch(config-if)# dot1x max-req 
count

Switch(config-if)#  
dot1x max-reauth-req count

Switch(config-if)# dot1x 
port-control auto

Switch(config-if)# end

Switch# show dot1x all

Switch# copy running-config 
startup-config

This example shows how to set 5 as the number of times that the switch retransmits an EAP-request/identity request before restarting the authentication process:

Switch# configure terminal

Switch(config)# interface fastethernet0/1

Switch(config-if)# switchport mode access

Switch(config-if)# dot1x pae authenticator

Switch(config-if)# dot1x max-reauth-req 5

Switch(config-if)# dot1x port-control auto

Switch(config-if)# end

Switch#

Manually Reauthenticating a Client Connected to a Port

You can manually reauthenticate a client connected to a specific port at any time by entering the
dot1x re-authenticate interface privileged EXEC command. If you want to enable or disable periodic reauthentication, see the "Enabling Periodic Reauthentication" section.

This example shows how to manually reauthenticate the client connected to Fast Ethernet port 1/1:

Switch# dot1x re-authenticate interface fastethernet1/1

Starting reauthentication on FastEthernet1/1

Initializing the 802.1X Authentication State

The dot1x initialize command causes the authentication process to be restarted irrespective of the state it is in currently.

This example shows how to restart the authentication process on Fast Ethernet port 1/1:

Switch# dot1x initialize interface fastethernet1/1

This example shows how to restart the authentication process on all ports of the switch:

Switch# dot1x initialize

Removing 802.1X Client Information

The clear dot1x command causes all existing supplicants to be completely deleted from an interface or from all the interfaces on a switch.

This example shows how to remove 802.1X client information on Fast Ethernet port 1/1:

Switch# clear dot1x interface fastethernet1/1

This example shows how to remove 802.1X client information on all ports of the switch:

Switch# clear dot1x all

Resetting the 802.1X Configuration to the Default Values

To reset the 802.1X configuration to the default values, perform this task:

Switch# configure terminal

Switch(config)# dot1x default

Switch(config)# end

Switch# show dot1x all

Switch# copy running-config 
startup-config

Displaying 802.1X Statistics and Status

To display 802.1X statistics for all interfaces, use the show dot1x all statistics privileged EXEC command.

To display the 802.1X administrative and operational status for the switch, use the
show dot1x all details privileged EXEC command. To display the 802.1X administrative and operational status for a specific interface, use the show dot1x interface details privileged EXEC command.