Catalyst 4500 Series Switch Software Configuration Guide, 12.2(40)SG

Configuring VRF-lite

Virtual Private Networks (VPNs) provide a secure way for customers to share bandwidth over an ISP backbone network. A VPN is a collection of sites sharing a common routing table. A customer site is connected to the service provider network by one or more interfaces, and the service provider associates each interface with a VPN routing table. A VPN routing table is called a VPN routing/forwarding (VRF) table.

With the VRF-lite feature, the Catalyst 4500 series switch supports multiple VPN routing/forwarding instances in customer edge devices. (VRF-lite is also termed multi-VRF CE, or multi-VRF Customer Edge Device). VRF-lite allows a service provider to support two or more VPNs with overlapping IP addresses using one interface.

Note The switch does not use Multiprotocol Label Switching (MPLS) to support VPNs. For information about MPLS VRF, refer to the Cisco IOS Switching Services Configuration Guide at
: http://www.cisco.com/en/US/docs/ios/mpls/configuration/guide/mp_vpn_ipv4_ipv6_ps6922_TSD_Products_Configuration_Guide_Chapter.html

Note For complete syntax and usage information for the switch commands used in this chapter, refer to the Catalyst 4500 Series Switch Cisco IOS Command Reference and related publications at this location:

http://www.cisco.com/en/US/products/ps6350/index.html

This chapter includes these topics:

•Understanding VRF-lite

•Default VRF-lite Configuration

•VRF-lite Configuration Guidelines

•Configuring VRFs

•Configuring a VPN Routing Session

•Configuring BGP PE to CE Routing Sessions

•VRF-lite Configuration Example

•Displaying VRF-lite Status

Note For complete syntax and usage information for the switch commands used in this chapter, refer to the Catalyst 4500 Series Switch Cisco IOS Command Reference and related publications at this location:

http://www.cisco.com/en/US/products/ps6350/index.html

Understanding VRF-lite

VRF-lite is a feature that enables a service provider to support two or more VPNs, where IP addresses can be overlapped among the VPNs. VRF-lite uses input interfaces to distinguish routes for different VPNs and forms virtual packet-forwarding tables by associating one or more Layer 3 interfaces with each VRF. Interfaces in a VRF can be either physical, such as Ethernet ports, or logical, such as VLAN SVIs, but a Layer 3 interface cannot belong to more than one VRF at any time.

Note VRF-lite interfaces must be Layer 3 interfaces.

VRF-lite includes these devices:

•Customer edge (CE) devices provide customer access to the service provider network over a data link to one or more provider edge routers. The CE device advertises the site's local routes to the provider edge router and learns the remote VPN routes from it. A Catalyst 4500 series switch can be a CE.

•Provider edge (PE) routers exchange routing information with CE devices by using static routing or a routing protocol such as BGP, RIPv1, or RIPv2.

•The PE is only required to maintain VPN routes for those VPNs to which it is directly attached, eliminating the need for the PE to maintain all of the service provider VPN routes. Each PE router maintains a VRF for each of its directly connected sites. Multiple interfaces on a PE router can be associated with a single VRF if all of these sites participate in the same VPN. Each VPN is mapped to a specified VRF. After learning local VPN routes from CEs, a PE router exchanges VPN routing information with other PE routers by using internal BGP (IBPG).

•Provider routers (or core routers) are any routers in the service provider network that do not attach to CE devices.

With VRF-lite, multiple customers can share one CE, and only one physical link is used between the CE and the PE. The shared CE maintains separate VRF tables for each customer and switches or routes packets for each customer based on its own routing table. VRF-lite extends limited PE functionality to a CE device, giving it the ability to maintain separate VRF tables to extend the privacy and security of a VPN to the branch office.

Figure 31-1 shows a configuration where each Catalyst 4500 series switch acts as multiple virtual CEs. Because VRF-lite is a Layer 3 feature, each interface in a VRF must be a Layer 3 interface.

Figure 31-1 Catalyst 4500 Series Switches Acting as Multiple Virtual CEs

This is the packet-forwarding process in a VRF-lite CE-enabled network as shown in Figure 31-1:

•When the CE receives a packet from a VPN, it looks up the routing table based on the input interface. When a route is found, the CE forwards the packet to the PE.

•When the ingress PE receives a packet from the CE, it performs a VRF lookup. When a route is found, the router adds a corresponding MPLS label to the packet and sends it to the MPLS network.

•When an egress PE receives a packet from the network, it strips the label and uses the label to identify the correct VPN routing table. Then the egress PE performs the normal route lookup. When a route is found, it forwards the packet to the correct adjacency.

•When a CE receives a packet from an egress PE, it uses the input interface to look up the correct VPN routing table. If a route is found, the CE forwards the packet within the VPN.

To configure VRF, create a VRF table and specify the Layer 3 interface associated with the VRF. Then configure the routing protocols in the VPN and between the CE and the PE. BGP is the preferred routing protocol used to distribute VPN routing information across the provider's backbone. The VRF-lite network has three major components:

•VPN route target communities—Lists of all other members of a VPN community. You need to configure VPN route targets for each VPN community member.

•Multiprotocol BGP peering of VPN community PE routers—Propagates VRF reachability information to all members of a VPN community. You need to configure BGP peering in all PE routers within a VPN community.

•VPN forwarding—Transports all traffic between all VPN community members across a VPN service-provider network.

Default VRF-lite Configuration

Table 31-1 shows the default VRF configuration.

VRF-lite Configuration Guidelines

Consider these points when configuring VRF in your network:

•A switch with VRF-lite is shared by multiple customers, and all customers have their own routing tables.

•Because customers use different VRF tables, the same IP addresses can be reused. Overlapped IP addresses are allowed in different VPNs.

•VRF-lite lets multiple customers share the same physical link between the PE and the CE. Trunk ports with multiple VLANs separate packets among customers. All customers have their own VLANs.

•VRF-lite does not support all MPLS-VRF functionality: label exchange, LDP adjacency, or labeled packets.

•For the PE router, there is no difference between using VRF-lite or using multiple CEs. In Figure 31-1, multiple virtual Layer 3 interfaces are connected to the VRF-lite device.

•The Catalyst 4500 series switch supports configuring VRF by using physical ports, VLAN SVIs, or a combination of both. The SVIs can be connected through an access port or a trunk port.

•A customer can use multiple VLANs as long as they do not overlap with those of other customers. A customer's VLANs are mapped to a specific routing table ID that is used to identify the appropriate routing tables stored on the switch.

•The Layer 3 TCAM resource is shared between all VRFs. To ensure that any one VRF has sufficient CAM space, use the maximum routes command.

•A Catalyst 4500 series switch using VRF can support one global network and up to 64 VRFs. The total number of routes supported is limited by the size of the TCAM.

•Most routing protocols (BGP, OSPF, EIGRP, RIP and static routing) can be used between the CE and the PE. However, we recommend using external BGP (EBGP) for these reasons:

–BGP does not require multiple algorithms to communicate with multiple CEs.

–BGP is designed for passing routing information between systems run by different administrations.

–BGP makes it easy to pass attributes of the routes to the CE.

•VRF-lite does not support IGRP and ISIS.

•VRF-lite does not affect the packet switching rate.

•Multicast cannot be configured on the same Layer 3 interface at the same time.

•The capability vrf-lite subcommand under router ospf should be used when configuring OSPF as the routing protocol between the PE and the CE.

Configuring VRFs

To configure one or more VRFs, perform this task:

Switch# configure terminal

Switch(config)# ip routing

Switch(config)# ip vrf vrf-name

Switch(config-vrf)# rd 
route-distinguisher

Switch(config-vrf)# route-target 
{export | import | both} 
route-target-ext-community

Switch(config-vrf)# import map 
route-map

Switch(config-vrf)# interface 
interface-id

Switch(config-if)# ip vrf forwarding 
vrf-name

Switch(config-if)# end

Switch# show ip vrf [brief | detail | 
interfaces] [vrf-name]

Switch# copy running-config 
startup-config

Note For complete syntax and usage information for the commands, refer to the switch command reference for this release and the Cisco IOS Switching Services Command Reference for Release 12.2.

Use the no ip vrf vrf-name global configuration command to delete a VRF and to remove all interfaces from it. Use the no ip vrf forwarding interface configuration command to remove an interface from the VRF.

Configuring a VPN Routing Session

Routing within the VPN can be configured with any supported routing protocol (RIP, OSPF, or BGP) or with static routing. The configuration shown here is for OSPF, but the process is the same for other protocols.

To configure OSPF in the VPN, perform this task:

Use the no router ospf process-id vrf vrf-name global configuration command to disassociate the VPN forwarding table from the OSPF routing process.

Configuring BGP PE to CE Routing Sessions

To configure a BGP PE to CE routing session, perform this task:

Use the no router bgp autonomous-system-number global configuration command to delete the BGP routing process. Use the command with keywords to delete routing characteristics.

VRF-lite Configuration Example

Figure 31-2 is a simplified example of the physical connections in a network similar to that in Figure 31-1. OSPF is the protocol used in VPN1, VPN2, and the global network. BGP is used in the CE to PE connections. The example commands show how to configure the CE switch S8 and include the VRF configuration for switches S20 and S11 and the PE router commands related to traffic with switch S8. Commands for configuring the other switches are not included but would be similar.

Figure 31-2 VRF-lite Configuration Example

Configuring Switch S8

On switch S8, enable routing and configure VRF.

Switch# configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# ip routing 

Switch(config)# ip vrf v11

Switch(config-vrf)# rd 800:1

Switch(config-vrf)# route-target export 800:1

Switch(config-vrf)# route-target import 800:1

Switch(config-vrf)# exit

Switch(config)# ip vrf v12

Switch(config-vrf)# rd 800:2

Switch(config-vrf)# route-target export 800:2

Switch(config-vrf)# route-target import 800:2

Switch(config-vrf)# exit

Configure the loopback and physical interfaces on switch S8. Fast Ethernet interface 3/5 is a trunk connection to the PE. Interfaces 3/7 and 3/11 connect to VPNs:

Switch(config)# interface loopback1

Switch(config-if)# ip vrf forwarding v11

Switch(config-if)# ip address 8.8.1.8 255.255.255.0

Switch(config-if)# exit

Switch(config)# interface loopback2

Switch(config-if)# ip vrf forwarding v12

Switch(config-if)# ip address 8.8.2.8 255.255.255.0

Switch(config-if)# exit

Switch(config)# interface FastEthernet3/5

Switch(config-if)# switchport trunk encapsulation dot1q

Switch(config-if)# switchport mode trunk

Switch(config-if)# no ip address

Switch(config-if)# exit

Switch(config)# interface FastEthernet3/8

Switch(config-if)# switchport access vlan 208

Switch(config-if)# no ip address

Switch(config-if)# exit

Switch(config)# interface FastEthernet3/11

Switch(config-if)# switchport trunk encapsulation dot1q

Switch(config-if)# switchport mode trunk

Switch(config-if)# no ip address

Switch(config-if)# exit

Configure the VLANs used on switch S8. VLAN 10 is used by VRF 11 between the CE and the PE. VLAN 20 is used by VRF 12 between the CE and the PE. VLANs 118 and 208 are used for VRF for the VPNs that include switch S11 and switch S20, respectively:

Switch(config)# interface Vlan10

Switch(config-if)# ip vrf forwarding v11

Switch(config-if)# ip address 38.0.0.8 255.255.255.0

Switch(config-if)# exit

Switch(config)# interface Vlan20

Switch(config-if)# ip vrf forwarding v12

Switch(config-if)# ip address 83.0.0.8 255.255.255.0

Switch(config-if)# exit

Switch(config)# interface Vlan118

Switch(config-if)# ip vrf forwarding v12

Switch(config-if)# ip address 118.0.0.8 255.255.255.0

Switch(config-if)# exit

Switch(config)# interface Vlan208

Switch(config-if)# ip vrf forwarding v11

Switch(config-if)# ip address 208.0.0.8 255.255.255.0

Switch(config-if)# exit

Configure OSPF routing in VPN1 and VPN2:

Switch(config)# router ospf 1 vrf vl1

Switch(config-router)# redistribute bgp 800 subnets

Switch(config-router)# network 208.0.0.0 0.0.0.255 area 0

Switch(config-router)# exit 

Switch(config)# router ospf 2 vrf vl2

Switch(config-router)# redistribute bgp 800 subnets

Switch(config-router)# network 118.0.0.0 0.0.0.255 area 0

Switch(config-router)# exit 

Configure BGP for CE to PE routing:

Switch(config)# router bgp 800

Switch(config-router)# address-family ipv4 vrf vl2

Switch(config-router-af)# redistribute ospf 2 match internal

Switch(config-router-af)# neighbor 83.0.0.3 remote-as 100

Switch(config-router-af)# neighbor 83.0.0.3 activate

Switch(config-router-af)# network 8.8.2.0 mask 255.255.255.0

Switch(config-router-af)# exit 

Switch(config-router)# address-family ipv4 vrf vl1

Switch(config-router-af)# redistribute ospf 1 match internal

Switch(config-router-af)# neighbor 38.0.0.3 remote-as 100

Switch(config-router-af)# neighbor 38.0.0.3 activate

Switch(config-router-af)# network 8.8.1.0 mask 255.255.255.0

Switch(config-router-af)# end 

Configuring Switch S20

Configure S20 to connect to CE:

Switch# configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# ip routing 

Switch(config)# interface Fast Ethernet 0/7

Switch(config-if)# no switchport

Switch(config-if)# ip address 208.0.0.20 255.255.255.0

Switch(config-if)# exit

Switch(config)# router ospf 101

Switch(config-router)# network 208.0.0.0 0.0.0.255 area 0

Switch(config-router)# end 

Configuring Switch S11

Configure S11 to connect to CE:

Switch# configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# ip routing 

Switch(config)# interface Gigabit Ethernet 0/3

Switch(config-if)# switchport trunk encapsulation dot1q

Switch(config-if)# switchport mode trunk 

Switch(config-if)# no ip address

Switch(config-if)# exit

Switch(config)# interface Vlan118

Switch(config-if)# ip address 118.0.0.11 255.255.255.0

Switch(config-if)# exit

Switch(config)# router ospf 101

Switch(config-router)# network 118.0.0.0 0.0.0.255 area 0

Switch(config-router)# end 

Configuring the PE Switch S3

On switch S3 (the router), these commands configure only the connections to switch S8:

Router# configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)# ip vrf v1

Router(config-vrf)# rd 100:1

Router(config-vrf)# route-target export 100:1

Router(config-vrf)# route-target import 100:1

Router(config-vrf)# exit

Router(config)# ip vrf v2

Router(config-vrf)# rd 100:2

Router(config-vrf)# route-target export 100:2

Router(config-vrf)# route-target import 100:2

Router(config-vrf)# exit

Router(config)# ip cef

Router(config)# interface Loopback1

Router(config-if)# ip vrf forwarding v1

Router(config-if)# ip address 3.3.1.3 255.255.255.0

Router(config-if)# exit

Router(config)# interface Loopback2

Router(config-if)# ip vrf forwarding v2

Router(config-if)# ip address 3.3.2.3 255.255.255.0

Router(config-if)# exit

Router(config)# interface Fast Ethernet3/0.10

Router(config-if)# encapsulation dot1q 10

Router(config-if)# ip vrf forwarding v1

Router(config-if)# ip address 38.0.0.3 255.255.255.0

Router(config-if)# exit

Router(config)# interface Fast Ethernet3/0.20

Router(config-if)# encapsulation dot1q 20

Router(config-if)# ip vrf forwarding v2

Router(config-if)# ip address 83.0.0.3 255.255.255.0

Router(config-if)# exit

Router(config)# router bgp 100

Router(config-router)# address-family ipv4 vrf v2

Router(config-router-af)# neighbor 83.0.0.8 remote-as 800

Router(config-router-af)# neighbor 83.0.0.8 activate

Router(config-router-af)# network 3.3.2.0 mask 255.255.255.0

Router(config-router-af)# exit 

Router(config-router)# address-family ipv4 vrf vl

Router(config-router-af)# neighbor 83.0.0.8 remote-as 800

Router(config-router-af)# neighbor 83.0.0.8 activate

Router(config-router-af)# network 3.3.1.0 mask 255.255.255.0

Router(config-router-af)# end 

Displaying VRF-lite Status

To display information about VRF-lite configuration and status, perform one of the following tasks:

Note For more information about the information in the displays, refer to the Cisco IOS Switching Services Command Reference at: http://www.cisco.com/en/US/docs/ios/ipswitch/command/reference/isw_book.html