IP Theft

Introduction to IP Theft

The IP Theft feature prevents the usage of an IP address that is already assigned to another device. If the controller finds that two wireless clients are using the same IP address, it declares the client with lesser precedence binding as the IP thief and allows the other client to continue. If blocked list is enabled, the client is put on the exclusion list and thrown out.

The IP Theft feature is enabled by default on the controller. The preference level of the clients (new and existing clients in the database) are also used to report IP theft. The preference level is a learning type or source of learning, such as Dynamic Host Configuration Protocol (DHCP), Address Resolution Protocol (ARP), data glean (looking at the IP data packet that shows what IP address the client is using), and so on. The wired clients always get a higher preference level. If a wireless client tries to steal the wired IP, that client is declared as a thief.


Note

Some devices might use different MAC addresses but the same IPv6 link-local addresses, for different WLANs. If the devices switch WLANs when they are not in range of the APs, an IP theft event is triggered. To avoid this, we recommend that you lower the idle timeout for the devices. When the devices are out of the APs' range, the idle timeout takes effect and the old entries in the initial WLAN are deleted.

The order of preference for IPv4 clients are:

  1. DHCPv4

  2. ARP

  3. Data packets

The order of preference for IPv6 clients are:

  1. DHCPv6

  2. NDP

  3. Data packets


Note

The static wired clients have a higher preference over DHCP.

Configuring IP Theft (GUI)

Procedure

Step 1

Choose Configuration > Security > Wireless Protection Policies > Client Exclusion Policies.

Step 2

Check the IP Theft or IP Reuse check box.

Step 3

Click Apply.

Configuring IP Theft

Follow the procedure given below to configure the IP Theft feature:

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

wireless wps client-exclusion ip-theft

Example:

Device(config)# wireless wps client-exclusion ip-theft

Configures the client exclusion policy.

Configuring the IP Theft Exclusion Timer

Follow the procedure given below to configure the IP theft exclusion timer:

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

wireless profile policy profile-policy

Example:

Device(config)# wireless profile policy default-policy-profile

Configures a WLAN policy profile and enters wireless policy configuration mode.

Step 3

exclusionlist timeout time-in-seconds

Example:

Device(config-wireless-policy)# exclusionlist timeout 5

Specifies the timeout, in seconds. The valid range is from 0-2147483647. Enter zero (0) for no timeout.

Adding Static Entries for Wired Hosts

Follow the procedure given below to create static wired bindings:


Note

The statically configured wired bindings and locally configured SVI IP addresses have a higher precedence than DHCP.

Procedure

  Command or Action Purpose

Step 1

configure terminal

Example:

Device# configure terminal

Enters global configuration mode.

Step 2

Use the first option to configure an IPv4 static entry or the second option to create an IPv6 static entry.

  • device-tracking binding vlan vlan-id ipv4-address interface gigabitEthernetge-intf-num hardware-or-mac-address
  • device-tracking binding vlan vlan-id ipv6-address interface gigabitEthernetge-intf-num hardware-or-mac-address

Example:

Device(config)# device-tracking binding vlan 20 20.20.20.5 interface gigabitEthernet 1 0000.1111.2222

Example:

Device(config)# device-tracking binding vlan 20 2200:20:20::6 interface gigabitEthernet 1 0000.444.3333

Configures IPv4 or IPv6 static entry.

Verifying IP Theft Configuration

Use the following command to check if the IP Theft feature is enabled or not:

Device# show wireless wps summary

Client Exclusion Policy
  Excessive 802.11-association failures   : Enabled
  Excessive 802.11-authentication failures: Enabled
  Excessive 802.1x-authentication         : Enabled
  IP-theft                                : Enabled
  Excessive Web authentication failure    : Enabled
  Cids Shun failure                       : Enabled
  Misconfiguration failure                : Enabled
  Failed Qos Policy                       : Enabled
  Failed Epm                              : Enabled

Use the following commands to view additional details about the IP Theft feature:

Device# show wireless client summary 

Number of Local Clients: 1

MAC Address    AP Name                WLAN State              Protocol Method     Role
-------------------------------------------------------------------------------------------
000b.bbb1.0001 SimAP-1                2    Run                11a      None       Local             

Number of Excluded Clients: 1

MAC Address    AP Name                WLAN State              Protocol Method     
-------------------------------------------------------------------------------------------
10da.4320.cce9 charlie2               2    Excluded           11ac     None       



Device# show wireless device-tracking database ip 

IP                              VLAN  STATE       DISCOVERY   MAC
  -------------------------------------------------------------------------
  20.20.20.2                     20    Reachable   Local      001e.14cc.cbff 
  20.20.20.6                     20    Reachable   IPv4 DHCP  000b.bbb1.0001 



Device# show wireless exclusionlist 

Excluded Clients

MAC Address       Description          Exclusion Reason               Time Remaining  
-----------------------------------------------------------------------------------------
10da.4320.cce9                         IP address theft                    59

Note

Client exclusion timer deletes the entry from exclusion list with a granularity of 10 seconds. The entry is checked to retain or delete after every 10 seconds. There are chances that the running timer value for excluded clients might display negative values upto 10 seconds. 

Device# show wireless exclusionlist client mac 12da.4820.cce9 detail 

Client State : Excluded
Client MAC Address : 12da.4820.cce9
Client IPv4 Address: 20.20.20.6
Client IPv6 Address: N/A
Client Username: N/A
Exclusion Reason : IP address theft
Authentication Method : None
Protocol: 802.11ac
AP MAC Address : 58ac.780e.08f0
AP Name: charlie2
AP slot : 1
Wireless LAN Id : 2
Wireless LAN Name: mhe-ewlc
VLAN Id : 20