Sample Output from the show dmvpn Command
The following sample output is from the show dmvpncommand, with the ipv6 and detail keywords, for the hub:
Router# show dmvpn ipv6 detail
Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete
N - NATed, L - Local, X - No Socket
# Ent --> Number of NHRP entries with same NBMA peer
NHS Status: E --> Expecting Replies, R --> Responding
UpDn Time --> Up or Down Time for a Tunnel
==========================================================================
Interface Tunnel1 is up/up, Addr. is 10.0.0.3, VRF ""
Tunnel Src./Dest. addr: 192.169.2.9/MGRE, Tunnel VRF ""
Protocol/Transport: "multi-GRE/IP", Protect "test_profile"
Type:Hub, Total NBMA Peers (v4/v6): 2
1.Peer NBMA Address: 192.169.2.10
Tunnel IPv6 Address: 2001::4
IPv6 Target Network: 2001::4/128
# Ent: 2, Status: UP, UpDn Time: 00:01:51, Cache Attrib: D
Type:Hub, Total NBMA Peers (v4/v6): 2
2.Peer NBMA Address: 192.169.2.10
Tunnel IPv6 Address: 2001::4
IPv6 Target Network: FE80::2/128
# Ent: 0, Status: UP, UpDn Time: 00:01:51, Cache Attrib: D
Type:Hub, Total NBMA Peers (v4/v6): 2
3.Peer NBMA Address: 192.169.2.11
Tunnel IPv6 Address: 2001::5
IPv6 Target Network: 2001::5/128
# Ent: 2, Status: UP, UpDn Time: 00:26:38, Cache Attrib: D
Type:Hub, Total NBMA Peers (v4/v6): 2
4.Peer NBMA Address: 192.169.2.11
Tunnel IPv6 Address: 2001::5
IPv6 Target Network: FE80::3/128
# Ent: 0, Status: UP, UpDn Time: 00:26:38, Cache Attrib: D
Pending DMVPN Sessions:
Interface: Tunnel1
IKE SA: local 192.169.2.9/500 remote 192.169.2.10/500 Active
Crypto Session Status: UP-ACTIVE
fvrf: (none), Phase1_id: 192.169.2.10
IPSEC FLOW: permit 47 host 192.169.2.9 host 192.169.2.10
Active SAs: 2, origin: crypto map
Outbound SPI : 0x BB0ED02, transform : esp-3des esp-sha-hmac
Socket State: Open
Interface: Tunnel1
IKE SA: local 192.169.2.9/500 remote 192.169.2.11/500 Active
Crypto Session Status: UP-ACTIVE
fvrf: (none), Phase1_id: 192.169.2.11
IPSEC FLOW: permit 47 host 192.169.2.9 host 192.169.2.11
Active SAs: 2, origin: crypto map
Outbound SPI : 0xB79B277B, transform : esp-3des esp-sha-hmac
Socket State: Open
The following sample output is from the show dmvpncommand, with the ipv6 and detail keywords, for the spoke:
Router# show dmvpn ipv6 detail
Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete
N - NATed, L - Local, X - No Socket
# Ent --> Number of NHRP entries with same NBMA peer
NHS Status: E --> Expecting Replies, R --> Responding
UpDn Time --> Up or Down Time for a Tunnel
==========================================================================
Interface Tunnel1 is up/up, Addr. is 10.0.0.1, VRF ""
Tunnel Src./Dest. addr: 192.169.2.10/MGRE, Tunnel VRF ""
Protocol/Transport: "multi-GRE/IP", Protect "test_profile"
IPv6 NHS: 2001::6 RE
Type:Spoke, Total NBMA Peers (v4/v6): 1
1.Peer NBMA Address: 192.169.2.9
Tunnel IPv6 Address: 2001::6
IPv6 Target Network: 2001::/112
# Ent: 2, Status: NHRP, UpDn Time: never, Cache Attrib: S
IPv6 NHS: 2001::6 RE
Type:Unknown, Total NBMA Peers (v4/v6): 1
2.Peer NBMA Address: 192.169.2.9
Tunnel IPv6 Address: FE80::1
IPv6 Target Network: FE80::1/128
# Ent: 0, Status: UP, UpDn Time: 00:00:24, Cache Attrib: D
Pending DMVPN Sessions:
Interface: Tunnel1
IKE SA: local 192.169.2.10/500 remote 192.169.2.9/500 Active
Crypto Session Status: UP-ACTIVE
fvrf: (none), Phase1_id: 192.169.2.9
IPSEC FLOW: permit 47 host 192.169.2.10 host 192.169.2.9
Active SAs: 2, origin: crypto map
Outbound SPI : 0x6F75C431, transform : esp-3des esp-sha-hmac
Socket State: Open