Appendix D - Device Template Values

Device Template Values for IR1101_CELL_with_TRUNK

Devices on Remote Location 2 use device template Name: IR1101_CELL_with_TRUNK, the following table contains a list of variables on the template and some example values used on the implementation.

Table 48 Device Template Values for IR1101_CELL_with_TRUNK

Section

Variable/value

IR-1101-Location2-1

IR-1101-Location2-2

System: variables contain device specific settings. From this template, it is possible to configure baud rate for console connection.

Basic Configuration
system_site_id
10010206
10010206
system_system_ip
2.2.0.16
2.2.0.15
system_hostname
IR-1101-Loc2-1
IR-1101-Loc2-2
system_device_groups
RL,IR1101,US
RL,IR1101,US
system_console_baud_rate
9600
9600
GPS
system_latitude
44
44
system_longitude
-110
-110
Advanced
system_port_hop
FALSE
FALSE
system_port_offset
0
0

VPN0: Only one default route is defined since there is only one tunnel interface. Other fields are left blank since they are optional.
IPv4 Route (1)
vpn0_next_hop_ip_address_1
Cellular0/1/0
Cellular0/1/0
IPv4 Route (2)
vpn_ipv4_ip_prefix2
vpn0_next_hop_ip_address_2
IPv4 Route (3)
vpn_ipv4_ip_prefix3
vpn0_next_hop_ip_address_3

VPN0 interface Cellular: Note IPSec preference value is higher for the device with higher VRRP priority in order to have traffic symmetry for DPI. Shaping rate for QoS is defined in this section, this value should be configured according to service provider offered upstream bandwidth.
Basic Configuration
vpn0_cell1_int_shutdown
FALSE
FALSE
Tunnel>Advanced Options>Encapsulation
vpn0_cell0_1_0_tunnel_ipsec_preference
100
0
ACL
vpn_cell1_qos_shaping-rate
10000
10000

VPN Interface SVI 1(VPN 1): VRRP optional values are used on this location. VRRP tracks prefix list created on localized policy.
Basic Configuration
vpn_service_svi_shutdown
FALSE
FALSE
vpn_svi_if_name_SVI_1
vlan16
vlan16
vpn_svi_if_description_SVI_1
Shared Services
Shared Services
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.16.2/24
10.12.16.3/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
1
1
vpn_if_vrrp_priority_1
200
100
vpn_if_vrrp_track_prefix_list_1
Services-prefix
Services-prefix
vpn_if_vrrp_vrrp_ipaddress_1
10.12.16.1
10.12.16.1

VPN Interface SVI 1 (VPN 10)

Basic Configuration
vpn_service_svi_shutdown
FALSE
FALSE
vpn_svi_if_name_SVI_1
vlan116
vlan116
vpn_svi_if_description_SVI_1
Video
Video
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.116.2/24
10.12.116.3/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
1
1
vpn_if_vrrp_priority_1
200
100
vpn_if_vrrp_track_prefix_list_1
Services-prefix
Services-prefix
vpn_if_vrrp_vrrp_ipaddress_1
10.12.116.1
10.12.116.1

VPN Interface SVI 1 (VPN 11)

Basic Configuration
vpn_service_svi_shutdown
FALSE
FALSE
vpn_svi_if_name_SVI_1
vlan216
vlan216
vpn_svi_if_description_SVI_1
Employee voice
Employee voice
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.216.2/24
10.12.216.3/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
1
1
vpn_if_vrrp_priority_1
200
100
vpn_if_vrrp_track_prefix_list_1
Services-prefix
Services-prefix
vpn_if_vrrp_vrrp_ipaddress_1
10.12.216.1
10.12.216.1

VPN Interface Ethernet (Loopback0)

IPv4 Configuration
lo0_int_ip_addr|maskbits
2.2.0.16/32
2.2.0.15/32

Switchport: FastEthernet0/0/1 is configured as a port in both routers to connect to Industrial Ethernet switch
Interface 1 (FE0/0/1)
switchport_1_if_shutdown
FALSE
FALSE
switchport_1_if_trunk_allowed_vlans
1,16,116,216,236
1,16,116,216,236
Interface 2 (FE0/0/2)
switchport_2_if_shutdown
FALSE
FALSE
switchport_2_if_access_vlan
16
16
Interface 3 (FE0/0/3)
switchport_3_if_shutdown
FALSE
FALSE
switchport_3_if_access_vlan
116
116
Interface 4 (FE0/0/4)
switchport_4_if_shutdown
FALSE
FALSE
switchport_4_if_access_vlan
216
216

SNMP

Basic Configuration
snmp_shutdown
FALSE
FALSE
snmp_device_name
IR-1101-Loc2-1
IR-1101-Loc2-2
snmp_device_location
Yellowstone
Yellowstone

Device Template Values for IR1101_INET_and_CELL

IR1101 on Remote Location 1 uses device template Name: IR1101_INET_and_CELL, the following table contains a list of variables on the template and some example values used on the implementation.

Table 49 Device Template Values for IR1101_INET_and_CELL

Section

Variable

IR1101-Location-1

System: variables contain device specific settings. From this template, it is possible to configure baud rate for console connection.

Basic Configuration
system_site_id
10010213
system_system_ip
2.2.0.13
system_hostname
IR1101-Location-1
system_device_groups
RL,IR1101,US,L1
system_console_baud_rate
9600
GPS
system_latitude
44.34
system_longitude
-68.27
Advanced
system_port_hop
FALSE
system_port_offset
0
VPN0: two default routes are defined, one for each WAN interface
IPv4 Route (1)
vpn0_next_hop_ip_address_1
GigabitEthernet0/0/0
IPv4 Route (2)
vpn_ipv4_ip_prefix2
0.0.0.0/0
vpn0_next_hop_ip_address_2
Cellular0/1/0
IPv4 Route (3)
vpn_ipv4_ip_prefix3
vpn0_next_hop_ip_address_3
VPN0 interface Cellular: IPSec preference is set to default value 0, while wired interface preference is set higher. Internet tunnel will be preferred. Shaping rate is defined as 10Mbps for this interface. This value should be configured according to service provider offered upstream bandwidth.
Basic Configuration
vpn0_cell1_int_shutdown
FALSE
Tunnel>Advanced Options>Encapsulation
vpn0_cell0_1_0_tunnel_ipsec_preference
0
ACL
vpn_cell1_qos_shaping-rate
10000
VPN0 interface INET: IPSec preference set to 100, Internet will be the preferred transport. Shaping rate is defined as 100Mbps for this interface. This value should be configured according to service provider offered upstream bandwidth.
Basic Configuration
vpn0_inet_int_shutdown
FALSE
Device Specific
vpn0_inet_tunnel_ipsec_preference
100
ACL/QoS
vpn_inet_qos_shaping-rate
100000
VPN Interface SVI 1(VPN 1): VRRP values are left blank since there is no VRRP on this location
Basic Configuration
vpn_service_svi_shutdown
FALSE
vpn_svi_if_name_SVI_1
vlan13
vpn_svi_if_description_SVI_1
Shared Services
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.13.1/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
vpn_if_vrrp_priority_1
vpn_if_vrrp_track_prefix_list_1
vpn_if_vrrp_vrrp_ipaddress_1
DHCP (VPN1-SVI1): DHCP server for VPN1 SVI1 network
Basic Configuration
voice_dhcp_addr_pool|maskbits
10.12.13.0/24
Basic Configuration
voice_dhcp_addr_exclude_range
10.12.13.1-10.12.13.20,10.12.13.100-10.12.13.155
Advanced
dhcp_default_gateway
10.12.13.1
VPN Interface SVI 1 (VPN 10): VRRP values are left blank since there is no VRRP on this location
Basic Configuration
vpn_service_svi_shutdown
FALSE
vpn_svi_if_name_SVI_1
vlan113
vpn_svi_if_description_SVI_1
Video
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.113.1/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
vpn_if_vrrp_priority_1
vpn_if_vrrp_track_prefix_list_1
vpn_if_vrrp_vrrp_ipaddress_1
DHCP (VPN10-SVI1): DHCP server for VPN10 SVI1 network
Basic Configuration
voice_dhcp_addr_pool|maskbits
10.12.113.0/24
Basic Configuration
voice_dhcp_addr_exclude_range
10.12.113.1-10.12.113.20,10.12.113.100-10.12.113.155
Advanced
dhcp_default_gateway
10.12.113.1
VPN Interface SVI 1 (VPN 11): VRRP values are left blank since there is no VRRP on this location
Basic Configuration
vpn_service_svi_shutdown
FALSE
vpn_svi_if_name_SVI_1
vlan213
vpn_svi_if_description_SVI_1
Employee voice
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.213.1/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
vpn_if_vrrp_priority_1
vpn_if_vrrp_track_prefix_list_1
vpn_if_vrrp_vrrp_ipaddress_1
VPN Interface SVI 2(VPN 11): Second SVI for a service VPN is created in this template. VRRP values are left blank since there is no VRRP on this location.
Basic Configuration
vpn_service_svi_shutdown
FALSE
vpn_svi_if_name_SVI_2
vlan233
vpn_svi_if_description_SVI_2
Employee Data
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_2
10.12.233.1/24
vpn_svi_dhcp_helper_SVI_2
10.22.2.4
VRRP
vpn_if_vrrp_grpid_2
vpn_if_vrrp_priority_2
vpn_if_vrrp_track_prefix_list_2
vpn_if_vrrp_vrrp_ipaddress_2
VPN Interface Ethernet (Loopback0)
IPv4 Configuration
lo0_int_ip_addr|maskbits
2.2.0.13/32
Switchport
Interface 1 (FE0/0/1)
switchport_1_if_shutdown
FALSE
switchport_1_if_access_vlan
13
Interface 2 (FE0/0/2)
switchport_2_if_shutdown
FALSE
switchport_2_if_access_vlan
113
Interface 3 (FE0/0/3)
switchport_3_if_shutdown
FALSE
switchport_3_if_access_vlan
213
Interface 4 (FE0/0/4)
switchport_4_if_shutdown
FALSE
switchport_4_if_access_vlan
233
SNMP
Basic Configuration
snmp_shutdown
FALSE
snmp_device_name
IR1101-Location-1
snmp_device_location
Acadia
Cellular Profile: required for non-default APNs. Original profile 1 is overwritten with new APN value.
Basic Configuration
cellular_profile_profile_id
1
cellular_profile_apn
globaldata.net

Device Template Values for IR1101_DUAL_CELL_EM

IR1101 on Remote Location 4 uses device template Name: IR1101_DUAL_CELL_EM, the following table contains a list of variables on the template and some example values used on the implementation.

Table 50 Device Template Values for IR1101_DUAL_CELL_EM

Section

Variable

IR1101-Location-1

System: variables contain device specific settings. From this template, it is possible to configure baud rate for console connection.

Basic Configuration
system_site_id
10010212
system_system_ip
2.2.0.12
system_hostname
IR1101-Location-4
system_device_groups
RL,IR1101,US,L4
system_console_baud_rate
9600
GPS
system_latitude
47.82
system_longitude
-123.78
Advanced
system_port_hop
FALSE
system_port_offset
0

VPN0: two default routes are defined, one for each WAN interface
IPv4 Route (1)
vpn0_next_hop_ip_address_1
Cellular0/1/0
IPv4 Route (2)
vpn_ipv4_ip_prefix2
0.0.0.0/0
vpn0_next_hop_ip_address_2
Cellular0/3/0
IPv4 Route (3)
vpn_ipv4_ip_prefix3
vpn0_next_hop_ip_address_3

VPN0 interface Cellular: IPSec preference is set to default value 0 on both cellular interfaces, in this case load will be shared on both tunnels. Shaping rate is defined as 10Mbps for this interface, this value should be configured according to service provider offered upstream bandwidth.
Basic Configuration
vpn0_cell1_int_shutdown
FALSE
Tunnel>Advanced Options>Encapsulation
vpn0_cell0_3_0_tunnel_ipsec_preference
0
ACL
vpn_cell3_qos_shaping-rate
10000

VPN0 interface Cellular Expansion Module: IPSec preference is set to default value 0 on both cellular interfaces, in this case load will be shared on both tunnels. Shaping rate is defined as 10Mbps for this interface, this value should be configured according to service provider offered upstream bandwidth.
Basic Configuration
vpn0_cell3_int_shutdown
FALSE
Tunnel>Advanced Options>Encapsulation
vpn0_cell0_1_0_tunnel_ipsec_preference
0
ACL
vpn_cell1_qos_shaping-rate
10000

VPN Interface SVI 1(VPN 1): VRRP values are left blank since there is no VRRP on this location
Basic Configuration
vpn_service_svi_shutdown
FALSE
vpn_svi_if_name_SVI_1
vlan12
vpn_svi_if_description_SVI_1
Shared Services
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.12.1/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
vpn_if_vrrp_priority_1
vpn_if_vrrp_track_prefix_list_1
vpn_if_vrrp_vrrp_ipaddress_1

VPN Interface SVI 1 (VPN 10): VRRP values are left blank since there is no VRRP on this location
Basic Configuration
vpn_service_svi_shutdown
FALSE
vpn_svi_if_name_SVI_1
vlan112
vpn_svi_if_description_SVI_1
security
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.112.1/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
vpn_if_vrrp_priority_1
vpn_if_vrrp_track_prefix_list_1
vpn_if_vrrp_vrrp_ipaddress_1

VPN Interface SVI 1 (VPN 11): VRRP values are left blank since there is no VRRP on this location
Basic Configuration
vpn_service_svi_shutdown
FALSE
vpn_svi_if_name_SVI_1
vlan212
vpn_svi_if_description_SVI_1
employee data
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.212.1/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
vpn_if_vrrp_priority_1
vpn_if_vrrp_track_prefix_list_1
vpn_if_vrrp_vrrp_ipaddress_1

VPN Interface SVI 2(VPN 11): Second SVI for a service VPN is created in this template. VRRP values are left blank since there is no VRRP on this location.
Basic Configuration
vpn_service_svi_shutdown
FALSE
vpn_svi_if_name_SVI_2
vlan232
vpn_svi_if_description_SVI_2
employee voice
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_2
10.12.232.1/24
vpn_svi_dhcp_helper_SVI_2
10.22.2.4
VRRP
vpn_if_vrrp_grpid_2
vpn_if_vrrp_priority_2
vpn_if_vrrp_track_prefix_list_2
vpn_if_vrrp_vrrp_ipaddress_2

VPN Interface Ethernet (Loopback0)
IPv4 Configuration
lo0_int_ip_addr|maskbits
2.2.0.12/32

Switchport: this template has 4 Fast Ethernet ports configured for access and one Gigabit ethernet port configured as trunk.
Interface 1 (FE0/0/1)
switchport_1_if_shutdown
FALSE
switchport_1_if_access_vlan
12
Interface 2 (FE0/0/2)
switchport_2_if_shutdown
FALSE
switchport_2_if_access_vlan
112
Interface 3 (FE0/0/3)
switchport_3_if_shutdown
FALSE
switchport_3_if_access_vlan
212
Interface 4 (FE0/0/4)
switchport_4_if_shutdown
FALSE
switchport_4_if_access_vlan
232
Interface 5 (Gi0/0/5)
switchport_5_if_shutdown
FALSE
switchport_5_if_trunk_allowed_vlans
1,12,112,212,232

SNMP
Basic Configuration
snmp_shutdown
FALSE
snmp_device_name
IR1101-Location-4
snmp_device_location
Olympic

Device Template Values for IR1101_CELL_OSPF_with_TRUNK and IR1101_INET_OSPF_with_TRUNK

One Cisco IR1101 on Remote Location 3 uses device template Name: IR1101_CELL_OSPF_with_TRUNK, the other device uses IR1101_INET_OSPF_with_TRUNK. Following table contains a list of variables on the template and some example values used on the implementation.

Table 51 Device Template Values for IR1101_CELL_OSPF_with_TRUNK and IR1101_INET_OSPF_with_TRUNK

Section

Variable

IR1101-Location3-1

IR1101_INET_OSPF_with_TRUNK

IR1101-Location3-2 IR1101_CELL_OSPF_ with_TRUNK

System: variables contain device specific settings. From this template, it is possible to configure baud rate for console connection.

Basic Configuration
system_site_id
10010317
10010318
system_system_ip
2.2.0.117
2.2.0.118
system_hostname
IR1101-Location3-1
IR1101-Location3-2
system_device_groups
RL,IR1101,US,L3
RL,IR1101,US,L3
system_console_baud_rate
9600
9600
GPS
system_latitude
47.82
47.82
system_longitude
-123.78
-123.78
Advanced
system_port_hop
FALSE
FALSE
system_port_offset
0
0

VPN0: one default routes per device for the single transit
IPv4 Route (1)
vpn0_next_hop_ip_address_1
GigabitEthernet0/0/0
Cellular0/1/0
IPv4 Route (2)
vpn_ipv4_ip_prefix2
vpn0_next_hop_ip_address_2
IPv4 Route (3)
vpn_ipv4_ip_prefix3
vpn0_next_hop_ip_address_3

VPN0 interface Cellular: Only present on second device. Shaping rate set to 10Mbps, this value should be configured according to service provider offered upstream bandwidth. Preference is set to a lower number than WAN interface in the peer router to meet traffic symmetry requirement for DPI.
Basic Configuration
vpn0_cell1_int_shutdown
FALSE
Tunnel>Advanced Options>Encapsulation
vpn0_cell0_3_0_tunnel_ipsec_preference
0
ACL
vpn_cell3_qos_shaping-rate
10000

VPN0 interface INET: Only present on first device. Shaping rate set to 100Mbps, this value should be configured according to service provider offered upstream bandwidth. Preference is set to a higher number than WAN interface in the peer router to meet traffic symmetry requirement for DPI.
Basic Configuration
vpn0_inet_int_shutdown
FALSE
Device Specific
vpn0_inet_tunnel_ipsec_preference
100
ACL/QoS
vpn_inet_qos_shaping-rate
100000

VPN Interface SVI 1(VPN 1): VRRP values are left blank since there is no VRRP on this location.

Basic Configuration
vpn_service_svi_shutdown
FALSE
FALSE
vpn_svi_if_name_SVI_1
vlan17
vlan18
vpn_svi_if_description_SVI_1
Shared Services
Shared Services
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.17.1/24
10.12.18.1/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
vpn_if_vrrp_priority_1
vpn_if_vrrp_track_prefix_list_1
vpn_if_vrrp_vrrp_ipaddress_1

OSPF (VPN 1): Both routers advertise same networks but OSPF metric will be different depending on the associated local policy. Router with higher preference is assigned localized policy OSPF_EDGE_PREFER for a metric of 10, the other router is assigned localized policy OSPF_EDGE_SEC for a metric of 20. Metrics are assigned for traffic symmetry required for DPI
Basic Configuration
ospf_router_id
2.2.0.117
2.2.0.118
ospf_redistribute_route_policy
OSPF_EDGE_PREFER
OSPF_EDGE_SEC
Area
ospf_area_a_num
1
1
ospf_name_iface
vlan17
vlan18
ospf_area_range_address_0
10.22.2.0/24
10.22.2.0/24

VPN Interface SVI 1 (VPN 10): VRRP values are left blank since there is no VRRP on this location
Basic Configuration
vpn_service_svi_shutdown
FALSE
FALSE
vpn_svi_if_name_SVI_1
vlan117
vlan118
vpn_svi_if_description_SVI_1
security
security
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.117.1/24
10.12.118.1/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
vpn_if_vrrp_priority_1
vpn_if_vrrp_track_prefix_list_1
vpn_if_vrrp_vrrp_ipaddress_1

OSPF (VPN 10): Both routers advertise same networks but OSPF metric will be different depending on the associated local policy. Router with higher preference is assigned localized policy OSPF_EDGE_PREFER for a metric of 10, the other router is assigned localized policy OSPF_EDGE_SEC for a metric of 20. Metrics are assigned for traffic symmetry required for DPI
Basic Configuration
ospf_router_id
10.12.117.2
10.12.118.2
ospf_redistribute_route_policy
OSPF_EDGE_PREFER
OSPF_EDGE_SEC
Area
ospf_area_a_num
10
10
ospf_name_iface
vlan116
vlan116
ospf_area_range_address_0
10.22.10.0/24
10.22.10.0/24

VPN Interface SVI 1 (VPN 11): VRRP values are left blank since there is no VRRP on this location
Basic Configuration
vpn_service_svi_shutdown
FALSE
FALSE
vpn_svi_if_name_SVI_1
vlan217
vlan218
vpn_svi_if_description_SVI_1
employee data
employee data
IPv4 Configuration
vpn_if_svi_if_ipv4_prefix_SVI_1
10.12.217.1/24
10.12.218.1/24
vpn_svi_dhcp_helper_SVI_1
10.22.2.4
10.22.2.4
VRRP
vpn_if_vrrp_grpid_1
vpn_if_vrrp_priority_1
vpn_if_vrrp_track_prefix_list_1
vpn_if_vrrp_vrrp_ipaddress_1

OSPF (VPN 11): Both routers advertise same networks but OSPF metric will be different depending on the associated local policy. Router with higher preference is assigned localized policy OSPF_EDGE_PREFER for a metric of 10, the other router is assigned localized policy OSPF_EDGE_SEC for a metric of 20. Metrics are assigned for traffic symmetry required for DPI
Basic Configuration
ospf_router_id
10.12.217.2
10.12.218.2
ospf_redistribute_route_policy
OSPF_EDGE_PREFER
OSPF_EDGE_SEC
Area
ospf_area_a_num
11
11
ospf_name_iface
vlan216
vlan218
ospf_area_range_address_0
10.22.11.0/24
10.22.11.0/24

VPN Interface Ethernet (Loopback0)
IPv4 Configuration
lo0_int_ip_addr|maskbits
2.2.0.117/32
2.2.0.118/32

Switchport: Interface Fast Ethernet 0/0/1 is a trunk interface to be connected to Cisco IE switch. Other interfaces are access only to connect end devices.
Interface 1 (FE0/0/1)
switchport_1_if_shutdown
FALSE
FALSE
switchport_1_if_trunk_allowed_vlans
1,17,117,217,237
1,18,118,218,238
Interface 2 (FE0/0/2)
switchport_2_if_shutdown
FALSE
switchport_2_if_access_vlan
117
118
Interface 3 (FE0/0/3)
switchport_3_if_shutdown
FALSE
switchport_3_if_access_vlan
217
218
Interface 4 (FE0/0/4)
switchport_4_if_shutdown
FALSE
switchport_4_if_access_vlan
17
18

SNMP
Basic Configuration
snmp_shutdown
FALSE
FALSE
snmp_device_name
IR1101-Location3-1
IR1101-Location3-2
snmp_device_location
Olympic
Olympic