Basic Phone Administration Steps

Phone Administration Overview

This appendix provides minimum, basic configuration steps for you to do the following actions:

  • Add a new user to Cisco Unified Communications Manager

  • Configure a new phone for that user

  • Associate that user to that phone

  • Complete other basic end-user configuration tasks

The procedures provide one method for performing these tasks and are not the only way to perform these tasks. They are a streamlined approach to get a new user and the corresponding phone running on the system.

These procedures are designed to be used on a mature Cisco Unified Communications Manager system where calling search spaces, partitions, and other complicated configuration have already been done and are in place for existing users.

Example User Information

In the procedures that follow, examples are given when possible to illustrate some of the steps. Sample user and phone information used throughout these procedures includes:

  • User’s Name: John Doe

  • User ID: johndoe

  • Phone model: 6901

  • Protocol: SCCP

  • MAC address listed on phone: 00127F576611

  • Five-digit internal telephone number: 26640

Cisco Unified Communications Manager User Addition

This section describes steps for adding a user to Cisco Unified Communications Manager. Follow one of the procedures in this section, depending on your operating system and the manner in which you are adding the user.

Add User from External LDAP Directory

If you added a user to an LDAP Directory (a non-Cisco Unified Communications Server directory), you can immediately synchronize that directory to the Cisco Unified Communications Manager on which you are adding this same user and the phone user by following these steps:

Procedure

Step 1

Login to Cisco Unified Communications Manager.

Step 2

Choose System > LDAP > LDAP Directory.

Step 3

Use the Find button to locate your LDAP directory.

Step 4

Click the LDAP directory name.

Step 5

Click Perform Full Sync Now.

Note 

If you do not need to immediately synchronize the LDAP Directory to the Cisco Unified Communications Manager, the LDAP Directory Synchronization Schedule on the LDAP Directory window determines when the next autosynchronization occurs. However, the synchronization must occur before you can associate a new user to a device.

Step 6

Proceed to Phone Setup.

Add User Directly to Cisco Unified Communications Manager

If you are not using an LDAP directory, you can add a user directly to Cisco Unified Communications Manager by following these steps:

Procedure

Step 1

Choose User Management > End User.

Step 2

Click Add New.

The End User Configuration window appears.

Step 3

In the User Information pane of this window, enter the following:

  • User ID: Enter the user identification name. Cisco Unified Communications Manager does not permit modifying the user ID after it is created. You may use the following special characters: =, +, <, >, #, ;, \, , "", and blank spaces.

    Example: johndoe

  • Password and Confirm Password: Enter five or more alphanumeric or special characters for the user password. You may use the following special characters: =, +, <, >, #, ;, \, , "", and blank spaces.

  • Last Name: Enter the user last name. You may use the following special characters: =, +, <, >, #, ;, \, , "", and blank spaces.

    Example: doe

  • Telephone Number: Enter the primary directory number for the user. Users can have multiple lines on their phones.

    Example: 26640 (John Doe’s internal company telephone number)

Step 4

Click Save.

Step 5

Proceed to the section Phone Setup.

Phone Setup

To identify the user phone model and protocol, follow these steps:

Procedure

Step 1

From Cisco Unified Communications Manager, choose Device > Phone.

Step 2

Click Add New.

Step 3

Select the user phone model from the Phone Type drop-down list, then click Next.

The Phone Configuration window appears.

Note 

On the Phone Configuration window, you can use the default values for most of the fields.

Step 4

For the required fields, possible values can be configured as follows:

Note 

The configuration is based on the example of user johndoe.

  1. In the Device Information pane of this window:

    MAC Address

    Enter the MAC address of the phone, listed on a sticker on the back of phone.

    The MAC address is 12 hexadecimal characters long.

    Example: 00127F576611 (MAC address on John Doe’s phone)

    Description

    This is an optional field where you can enter a useful description. This will help you if you need to search for information about this user.

    Device Pool

    Choose the device pool for which you want to assign this phone. The device pool defines sets of common characteristics for devices, such as region, date/time group, and MLPP information.

    Note 

    Device Pools are defined on the Device Pool Configuration window of Cisco Unified Communications Server Administration (System > Device Pool).

    Phone Button Template

    Choose the appropriate phone button template from the drop-down list. The phone button template determines the configuration of features on a phone and identifies the predetermined number to be dialed after pressing the feature button. To configure the Predetermined Number for a feature, navigate to the Phone Button Template of Cisco Unified IP Phone 6911. In the template, 1 is always assigned to the line, so the button number minus 1 is the predetermined number that is provided by your system administrator.

    Note 

    Phone button templates are defined on the Phone Button Template Configuration window of Cisco Unified Communications Manager (Device > Device Settings > Phone Button Template). You can use the search fields and the Find button to find all configured phone button templates and their current settings.

    Common Phone Profile

    From the drop-down list, choose a common phone profile from the list of available common phone profiles.

    Note 

    Common Phone Profiles are defined on the Common Phone Profile Configuration window of Cisco Unified Communications Manager (Device > Device Settings > Common Phone Profile). You can use the search fields and the Find button to find all configured common phone profiles and their current settings.

    Calling Search Space

    From the drop-down list, choose the appropriate calling search space (CSS). A calling search space comprises a collection of partitions (analogous to a collection of available phone books) that are searched to determine how a dialed number should be routed. The calling search space for the device and the calling search space for the directory number get used together. The directory number CSS takes precedence over the device CSS.

    Note 

    Calling Search Spaces are defined on the Calling Search Space Configuration window of Cisco Unified Communications Manager (Calling routing > Class of Control > Calling Search Space). You can use the search fields and the Find button to find all configured Calling Search Spaces and their current settings.

    Location

    Choose the appropriate location for this Cisco Unified IP Phone.

    Owner User ID

    From the drop-down list, choose the user ID of the assigned phone user.

  2. In the Protocol Specific Information pane of this window, choose a Device Security Profile from the drop-down list. To enable security features for a phone, you must configure a new security profile for the device type and protocol and apply it to the phone. If the phone does not support security, choose a nonsecure profile.

    To identify the settings that are contained in the profile, choose System > Security Profile > Phone Security Profile.

    Note 

    The security profile chosen should be based on the overall security strategy of the company.

  3. In the Extension Information pane of this window, check the Enable Extension Mobility box if this phone supports Cisco Extension Mobility.

  4. Click Save.

Step 5

Configure line settings:

  1. On the Phone Configuration window, click Line 1 on the left pane of the window. The Directory Number Configuration window appears.

  2. In the Directory Number field, enter a valid number that can be dialed.

    Note 

    This field should contain the same number that appears in the Telephone Number field on the User Configuration window.

    Example: 26640 is the directory number of user John Doe in the example above.

  3. From the Route Partition drop-down list, choose the partition to which the directory number belongs. If you do not want to restrict access to the directory number, choose <None> for the partition.

  4. From the Calling Search Space drop-down list (Directory Number Settings pane of the Directory Number Configuration window), choose the appropriate calling search space. A calling search space comprises a collection of partitions that are searched for numbers that are called from this directory number. The value that you choose applies to all devices that are using this directory number.

  5. In the Call Pickup and Call Forward Settings pane of the Directory Number Configuration window, choose the items (for example, Forward All, Forward Busy Internal) and corresponding destinations to which calls should be sent.

    Example: If you want incoming internal and external calls that receive a busy signal to be forwarded to the voice mail for this line, check the Voice Mail box next to the Forward Busy Internal and Forward Busy External items in the left column of the Call Pickup and Call Forward Settings pane.

  6. In the Line 1 on Device... pane of the Directory Number Configuration window, configure the following parameters:

    Display (Internal Caller ID field)

    You can enter the first name and last name of the user of this device so that this name will be displayed for all internal calls. You can also leave this field blank to have the system display the phone extension.

    External Phone Number Mask

    Indicate phone number (or mask) that is used to send Caller ID information when a call is placed from this line.

    You can enter a maximum of 24 number and "X" characters. The X characters represent the directory number and must appear at the end of the pattern.

    Example: Using the John Doe extension in the example above, if you specify a mask of 408902XXXX, an external call from extension 6640 displays a caller ID number of 4089026640.

    This setting applies only to the current device unless you check the Update Shared Device Settings check box at right and click the Propagate Selected button. The check box only displays if other devices share this directory number.

  7. Click Save.

  8. Click Associate End Users at the bottom of the window to associate a user to the line being configured.

  9. Use the Find button and the Search fields to locate the user, check the box next to the user name, and then click Add Selected.

    The user’s name and user ID should appear in the Users Associated With Line pane of the Directory Number Configuration window.

  10. Click Save. The user is now associated with Line 1 on the phone.

  11. If the phone has a second line, configure Line 2.

  12. Associate the user with the device:

    1. Choose User Management > End User.

    2. Use the search boxes and the Find button to locate the user you have added (for example, doe for the last name).

    3. Click on the user ID (for example, johndoe). The End User Configuration window appears.

    4. Click Device Associations.

    5. Use the Search fields and the Find button to locate the device with which you want to associate to the user.

    6. Select the device, then click Save Selected/Changes. The user is now associated with the device.

    7. Click the Go button next to the Back to User Related link in the upper-right corner of the screen.

Step 6

Proceed to Perform Final End User Configuration Steps.

Perform Final End User Configuration Steps

If you are not already on the End User Configuration page, choose User Management > End User to perform some final configuration tasks. Use the Search fields and the Find button to locate the user (for example, John Doe), then click on the user ID to get to the End User Configuration window for the user. In the End User configuration window, do the following:

Procedure

Step 1

In the Directory Number Associations pane of the screen, set the primary extension from the drop-down list.

Step 2

In the Mobility Information pane, check the Enable Mobility box.

Step 3

In the Permissions Information pane, use the User Group buttons to add this user to any user groups. For example, you may want to add the user to a group that has been defined as a Standard CCM End User Group.

To view all configured user groups, choose User Management > User Group.

Step 4

Click Save.