Cisco CallManager Administration Guide, Release 3.1(1)
Media Termination Point Configuration

Table Of Contents

Media Termination Point Configuration

Adding a Media Termination Point

Updating a Media Termination Point

Deleting a Media Termination Point

Media Termination Point Configuration Settings


Media Termination Point Configuration


A Media Termination Point (MTP) software device allows the Cisco CallManager to extend supplementary services, such as hold and transfer, to calls routed through an H.323 endpoint or an H.323 gateway.

MTP, a Cisco software application, installs on a server during the software installation process. During installation, the component is called the "IpVoiceMediaStreamingApp" and is common to both the MTP, Conference Bridge, and Music on Hold (MOH) applications. Under Windows2000, the application runs as a service and is called "Cisco IP Voice Media Streaming App."

Each MTP device defined in the database registers with the Media Resource Manager (MRM). The MRM keeps track of the total available MTP devices in the system and which devices have available resources.

During resource reservation, the MRM determines the number of resources, identifies the media type (in this case, the MTP), and the location of the registered MTP device. The MRM updates its share resource table with the registration information and propagates the registered information to the other Cisco CallManagers within the cluster.

Unlike previous Cisco CallManager releases, the MTP and transcoder can register with the same Cisco CallManager. See the "Transcoder Configuration" section for more information.

Each MTP receives a list of Cisco CallManagers, in priority order, to which it should attempt to register. Each MTP can register with only one Cisco CallManager at a time.

Use the following topics to add, update, and delete MTPs:

Transcoder Configuration

Adding a Media Termination Point

Updating a Media Termination Point

Deleting a Media Termination Point

Media Termination Point Configuration Settings

Adding a Media Termination Point

This section describes how to add a Media Termination Point (MTP).


Note The service must be installed in order to perform this procedure.


Before You Begin

Make sure the following prerequisites are met before proceeding with the steps:

Servers must be configured.

Device pools must be configured.


Note Add only one Media Termination Point (MTP) device for each MTP application.


Procedure


Step 1 Choose Service> Media Termination Point.

Step 2 Enter the appropriate settings as described in Table 26-1.

Step 3 Click Insert.

A message displays stating that the MTP device must be reset before the changes take effect.

Step 4 Click OK.


Related Topics

Media Termination Point Configuration

Transcoder Configuration

Configuring a Transcoder

Updating a Media Termination Point

Deleting a Media Termination Point

Media Termination Point Configuration Settings

Updating a Media Termination Point

This section describes how to update a Media Termination Point (MTP).


Note The service must be installed in order to perform this procedure.


Before You Begin

Make sure the following prerequisites are met before proceeding with the steps:

Servers must be configured

Device pools must be configured

Media Termination Points must be configured

Procedure


Step 1 Choose Service> Media Termination Point.

Step 2 Choose the MTP you want to update from the Media Termination Points list.

The pane refreshes, showing the device you selected.

Step 3 Update the appropriate settings as described in Table 26-1.

Step 4 Click Update.

A message displays stating that the MTP device must be reset before the changes will take effect.

Step 5 Click OK.


Related Topics

Media Termination Point Configuration

Transcoder Configuration

Adding a Media Termination Point

Deleting a Media Termination Point

Media Termination Point Configuration Settings

Deleting a Media Termination Point

This section describes how to delete a Media Termination Point (MTP).


Note You must install the service to perform this procedure. You cannot delete a device if it is assigned to the Media Resource Manager (MRM).


Before You Begin

Make sure the following prerequisites are met before proceeding with the steps:

Servers must be configured

Device pools must be configured

Media Termination Points must be configured

Procedure


Step 1 Choose Service> Media Termination Point.

Step 2 From the Media Termination Points list, choose the MTP you want to delete.

Step 3 Click Delete.


Related Topics

Media Termination Point Configuration

Transcoder Configuration

Adding a Media Termination Point

Updating a Media Termination Point

Media Termination Point Configuration Settings

Table 26-1 describes the media termination point configuration settings.

Table 26-1 Media Termination Point Configuration Settings

Field
Description

Host Server

Choose the server on which you want MTP to run.

Media Termination Point Name

Enter a name for the MTP, up to 15 alphanumeric characters.

Description

Enter any description for the MTP.

Device Pool

Choose a device pool. The device pool specifies the list of Cisco CallManagers for this MTP.


Related Topics

Adding a Media Termination Point

Updating a Media Termination Point