Cisco IOS Voice Command Reference

11.3(6)NA2

This command was introduced.

12.0(5)T

The display format was modified for H.323 Version 2.

12.1(5)XM2

This command was implemented on the Cisco AS5350 and Cisco AS5400.

12.2(4)T

This command was not supported on the Cisco AS5300, Cisco AS5350, and Cisco AS5400 in this release.

12.2(2)XB1

This command was implemented on the Cisco AS5850.

12.2(11)T

This command was integrated into Cisco IOS Release 12.2(11)T.

resource threshold

Configures a gateway to report H.323 resource availability to the gatekeeper of the gateway.

12.4(4)XC

This command was introduced.

12.4(9)T

This command was integrated into Cisco IOS Release 12.4(9)T.

Called Number

The phone number entered by the caller.

CallID

The shortened name for connection ID displayed in the show call active voice brief command.

H225 FD

The file descriptor number of the H.225.0 TCP socket.

H245 FD

The file descriptor number of the H.245 TCP socket.

Preserved Duration

The time in seconds that the call has been preserved.

RemoteMediaIPAddress

The remote media IP address.

RemoteMediaPort

The remote media IP address.

RemoteSignallingIPAddress

The remote signaling IP address.

RemoteSignallingPort

The remote signaling port.

Total Duration

The time in seconds of the phone call.

call preserve

Enables the preservation of H.323 VoIP calls.

clear call voice

Clears one or more voice calls detected as inactive because there is no RTP or RTCP activity.

show call active voice

Displays call information for voice calls in progress.

show voice call

Displays the call status for voice ports on the Cisco router.

cause-code stats

(Optional) Output displays the disconnect cause codes that the H.323 subsystem has received. A disconnect can originate either from the far-end gateway or from the opposite call leg on the local gateway.

h225

(Optional) Output lists cumulative counts of the number of H.225 messages that have been sent and received since the counters were last cleared.

ras

(Optional) Output lists the counters for Registration, Admission, and Status (RAS) messages that have been sent to and received from the gatekeeper since the counters were last cleared.

12.2(4)T

This command was introduced on Cisco H.323 platforms except for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850.

DISC CAUSE CODE

Decimal value of the cause code, followed by the textual description.

FROM OTHER PEER

Number of disconnects that have been received from the opposite call leg for each cause code (for example, from a PRI T1 POTS peer or a Foreign exchange station [FXS] POTS peer).

FROM H323 PEER

Number of disconnects that have been received from the far-end gateway for each cause code.

H.225 REQUESTS

Types of H.225 messages.

SENT

Number of H.225 messages sent by the gateway.

RECEIVED

Number of H.225 messages received from a remote gateway or endpoint.

FAILED

Number of H.225 messages that could not be sent. A failure could occur if, for example, the H.323 subsystem tried to send an H.225 release request but the TCP socket had already been closed.

Setup

Number of setup messages that were sent, that were received, or that could not be sent. This message is sent by a calling H.323 entity to indicate its desire to set up a connection to the called entity.

Setup confirm

Number of setup confirm messages that were sent, that were received, or that could not be sent. This message may be sent by an H.323 entity to acknowledge receipt of a setup message.

Alert

Number of alert messages that were sent, that were received, or that could not be sent. This message may be sent by the called user to indicate that called user alerting has been initiated. (In everyday terms, the "phone is ringing.")

Progress

Number of progress messages that were sent, that were received, or that could not be sent. This message may be sent by an H.323 entity to indicate the progress of a call.

Call proceeding

Number of call proceeding messages that were sent, that were received, or that could not be sent. This message may be sent by the called user to indicate that requested call establishment has been initiated and that no more call establishment information is accepted.

Notify

Number of notify messages that were sent, that were received, or that could not be sent.

Info

Number of information messages that were sent, that were received, or that could not be sent.

User Info

Number of user information messages that were sent, that were received, or that could not be sent. This message may be used to provide additional information for call establishment (for example, overlap signaling), to provide miscellaneous call-related information, or to deliver proprietary features.

Facility

Number of facility messages that were sent, that were received, or that could not be sent. This message is used to provide information on where a call should be directed or for an endpoint to indicate that the incoming call must go through a gatekeeper.

Release

Number of release complete messages that were sent, that were received, or that could not be sent. This message is sent by a gateway to indicate the release of the call if the reliable call signaling channel is open.

Reject

Number of reject messages that were sent, that were received, or that could not be sent.

Passthrough

Number of pass-through messages that were sent, that were received, or that could not be sent.

H225 establish timeout

Number of times the H.323 subsystem was unable to establish an H.225 connection to a remote gateway for a call.

RAS failed

Number of times an Admission Reject (ARJ) or Disengage Reject (DRJ) message is received from the gatekeeper. This counter should equal the arj + drj received counters shown in the show h323 gateway ras command output.

H245 failed

Number of times the H.323 subsystem was unable to create an H.245 tunnel for a call or was unable to send an H.245 message.

RAS MESSAGE

Type RAS message.

REQUESTS SENT

Number of RAS request messages sent by the gateway to a gatekeeper.

CONFIRMS RCVD

Number of RAS confirmation messages received from a gatekeeper.

REJECTS RCVD

Number of RAS reject messages received from a gatekeeper.

RAS MESSAGE

Type of RAS message.

REQUESTS RCVD

Number of RAS request messages received from a gatekeeper.

CONFIRMS SENT

Number of RAS confirmation messages sent by the gateway.

REJECTS SENT

Number of RAS reject messages sent by the gateway.

GK Discovery

Gatekeeper Request (GRQ) message requests that any gatekeeper receiving it respond with a Gatekeeper Confirmation (GCF) message granting it permission to register. The Gateway Reject (GRJ) message is a rejection of this request, indicating that the requesting endpoint should seek another gatekeeper.

Registration

Registration Request (RRQ) message is a request from a terminal to a gatekeeper to register. If the gatekeeper responds with a Registration Confirmation (RCF) message, the terminal uses the responding gatekeeper for future calls. If the gatekeeper responds with a Registration Reject (RRJ) message, the terminal must seek another gatekeeper with which to register.

Admission

Admission Request (ARQ) message requests that an endpoint be allowed access to the packet-based network by the gatekeeper, which either grants the request with an Admission Confirmation (ACF) message or denies it with an Admission Reject (ARJ) message.

Bandwidth

Bandwidth Request (BRQ) message requests that an endpoint be granted a changed packet-based network bandwidth allocation by the gatekeeper, which either grants the request with a Bandwidth Confirmation (BCF) message or denies it with a Bandwidth Reject (BRJ) message.

Disengage

If sent from an endpoint to a gatekeeper, the Disengage Request (DRQ) message informs the gatekeeper that an endpoint is being dropped. If sent from a gatekeeper to an endpoint, the DRQ message forces a call to be dropped; such a request is not refused. The DRQ message is not sent directly between endpoints.

Unregister

UnRegistration Request (URQ) message requests that the association between a terminal and a gatekeeper be broken. Note that the URQ request is bidirectional; that is, a gatekeeper can request a terminal to consider itself unregistered, and a terminal can inform a gatekeeper that it is revoking a previous registration.

Resource Avail

Resource Availability Indication (RAI) message is a notification from a gateway to a gatekeeper of its current call capacity for each H-series protocol and data rate for that protocol. The gatekeeper responds with a Resource Availability Confirmation (RAC) message upon receiving an RAI message to acknowledge its reception.

Req In Progress

Request In Progress (RIP) message can be used by a gateway or gatekeeper when a response to a message cannot be generated within a typical retry timeout period. The RIP message specifies the time period after which a response should have been generated.

show h323 gateway prefixes

Displays the status of the destination-pattern database and the status of the individual destination patterns.

12.2(15)T

This command was introduced.

Pattern Database Status

Status of the gateway's destination-pattern database: active or inactive.

Status

Status of the destination pattern. The status can be one of the following values:

ADD PENDING—The gateway has a prefix that is waiting to be sent to the gatekeeper. Prefixes are sent only at the lightweight registration request (RRQ) RAS message schedule, which is every 30 seconds.

ADD SENT—The gateway sent the prefix to the gatekeeper and is waiting for it to be acknowledged by a registration confirm (RCF) RAS message.

ADD ACKNOWLEDGED—The gateway received an RCF message indicating that the gatekeeper accepted the prefix. This is the normal status when dynamic zone prefix registration is working properly.

ADD REJECTED—The gatekeeper did not accept the prefix and sent a registration reject (RRJ) RAS message. One reason for rejection could be that the gatekeeper already has this prefix registered for a different zone, either by static zone prefix configuration, or because another gateway in a different zone dynamically registered this prefix first.

DELETE PENDING—The prefix has gone out of service, for example, because the dial peer shut down, and the gateway is waiting to send an unregistration request (URQ) RAS message to the gatekeeper to remove it. URQ messages are sent at the lightweight RRQ schedule, which is every 30 seconds.

DELETE SENT—The gateway sent a URQ message to remove the prefix to the gatekeeper. There is no DELETE ACKNOWLEDGED status. If the prefix is subsequently brought back in service, the status goes back to ADD PENDING.

show h323 gateway

Displays statistics for H.323 gateway messages that have been sent and received and the reasons for which H.l323 calls have been disconnected.

brief

(Optional) Displays summary information about the HTTP client cache.

12.2(2)XB

This command was introduced on the Cisco AS5300, Cisco AS5350, and Cisco AS5400.

12.2(11)T

This command was integrated into Cisco IOS Release 12.2(11)T and implemented on the Cisco 3640 and Cisco 3660.

12.4(15)T

The command output was modified to display files cached with URLs of HTTP and HTTPS format in separate tables. The command output was modified to mask out values of the URL attributes when caching of query data returned from the HTTP server is enabled.

12.4(15)XY

A pound sign (#) was added next to the Age field in the command output to indicate entries marked stale manually.

12.4(20)T

This command was integrated into Cisco IOS Release 12.4(20)T

Maximum memory pool allowed for HTTP Client caching

Maximum amount of memory available for the HTTP client to store cached entries in kilobytes. This value is configured by using the http client cache memory command.

Maximum file size allowed for caching

Maximum size of a file that can be cached, in kilobytes. If a file exceeds this limit, it cannot be cached. This value is configured by using the http client cache memory command.

Total memory used up for Cache

Total amount of memory that is currently being used to store cached entries in kilobytes.

Total cached entries

Total number of cached entries.

Total non-cached entries

Total number of temporary, one-time used HTTP entries that are not currently cached.

Cached table entry

Index marker of the cached table entry. Each cached table entry can contain multiple URLs that were requested and cached.

number of cached entries

Number of URL entries in the cached table entry.

Request URL

URL of the cached entry.

Ref

Whether the cached entry is still in use by the application. 0 means the entry has been freed; 1 or more means that the entry is still being used by that number of applications.

FreshTime

Lifetime of a cached entry, in seconds. When an entry is the same age or older than the refresh time, the entry expires. When a request is made to a cached entry that has expired, the HTTP client sends the server a conditional request for an update.

This value is configured on the HTTP server or by using the http client cache refresh command on the gateway.

Age

Time for which the entry has been in the cache, in seconds.

•Pound sign (#) indicates entries marked stale manually.

•Asterisk (*) indicates entries that have become stale without manual intervention.

Size

Size of the cached entry, in bytes.

http client cache memory

Configures the HTTP client cache.

http client cache refresh

Configures the HTTP client cache refresh time.

http client response timeout

Configures the HTTP client server response timeout.

set http client cache stale

Sets the status of all entries in the HTTP client cache to stale.

show http client connection

Displays current HTTP client connection information.

12.2(2)XB

This command was introduced on the Cisco AS5300, Cisco AS5350, and Cisco AS5400.

12.2(11)T

This command was integrated into Cisco IOS Release 12.2(11)T and implemented on the Cisco 3640 and Cisco 3660.

Persistent connection

Whether HTTP keepalive connections have been enabled by using the http client connection persistent command.

Initial socket connection timeout

Number of seconds for which the HTTP client waits for a server to establish a connection before giving up. This value is set by using the http client connection timeout command.

Connection idle timeout

Number of seconds for which the HTTP client waits before terminating an idle connection. This value is set by using the http client connection idle timeout command.

Total HTTP server connections

Total number of current connections to an HTTP server.

http client cache memory

Configures the HTTP client cache.

http client connection idle timeout

Sets the number of seconds for which the HTTP client waits before terminating an idle connection.

http client connection persistent

Enables HTTP persistent connections so that multiple files can be loaded using the same connection.

http client connection timeout

Sets the number of seconds for which the HTTP client waits for a server to establish a connection before giving up.

http client response timeout

Configures the HTTP client server response.

id call-id

(Optional) Displays cookies for the specified call only.

12.3(8)T

This command was introduced.

debug http client cookie

Displays debugging traces related to HTTP cookies.

http client cache memory

Configures the memory limits for the HTTP client cache.

http client cache refresh

Configures the refresh time for the HTTP client cache.

http client cookie

Enables the HTTP client to send and receive and cookies.

show call active voice brief

Displays a call information summary for active calls.

show http client cache

Displays current HTTP client cache information.

12.2(2)XB

This command was introduced on the Cisco AS5300, Cisco AS5350, and Cisco AS5400.

12.2(11)T

This command was integrated into Cisco IOS Release 12.2(11)T and implemented on the Cisco 3640 and Cisco 3660.

http client cache memory

Configures the HTTP client cache.

http client response timeout

Configures the HTTP client server response.

show http client connection

Displays current HTTP client connection information.

12.4(15)T

This command was introduced.

HTTP Client Secure Ciphersuite

Cipher suites.

•3des_cbc_sha—Triple DES (Data Encryption Standard) encryption and the SHA (Secure Hash Algorithm) integrity method.

•des_cbc_sha—DES encryption and the SHA integrity method.

•null_md5—NULL encryption and the MD5 (Message-Digest algorithm 5) integrity method.

•rc4_128_md5—RC4 (or ARCFOUR) encryption and the MD5 integrity method.

•rc4_128_sha—RC4 encryption and the SHA integrity method.

HTTP Client Secure Trustpoint

Trustpoint name.

http client secure-trustpoint

Declares the trustpoint that the HTTP client will use.

http client secure-ciphersuite

Sets the secure encryption cipher suite for the HTTP client.

12.4(15)T

This command was introduced.

Elapsed time

Time elapsed since the first HTTP request, in milliseconds (ms).

total load count

Number of API events.

total byte count

Total bytes downloaded from the server by API requests.

largest file size
smallest file size

Size of largest and smallest files downloaded from the server, in bytes.

longest response to connect
shortest response to connect

Longest and shortest time taken by the server to establish a network connection requested by the client, in ms.

longest response to load
shortest response to load

Longest and shortest time taken by the server to fulfill a download request from the client, in ms.

longest load time
shortest load time

Longest and shortest time taken by the server to complete downloading the entire file, in ms.

max connections

Maximum concurrent connections.

established connections

Number of currently active and previously established connections.

Load Rate

Downloading rate in bytes/hour, bytes/minute, bytes/second, and bytes/ms.

app_requests

Number of GET and POST requests.

app_callbacks

Number of callbacks to the application.

200_OK_rsp

Number of server messages with response code 200 OK or 304 Not Modified.

other_rsp

Number of server messages with a response code other than 200 and 304.

total_errors

Number of errors encountered by the client.

client_timeouts

Number of timeouts the client has experienced, for example, response timeouts.

client_errs

Number of client internal errors, for example, software errors.

connect_errs/_timeouts

Number of failed or broken connections.

msg_decode_errs

Number of server response messages for which the client failed to decode the headers.

msg_encode_errs

Number of send messages for which the client failed to encode the headers.

msg_xmit_errs

Number of send messages that the client failed to transmit to the server.

write_Q_full

Number of times that the client failed to enter a send message requested by an application into the transmit queue.

socket_rcv_errs

Number of socket read error events returned by TCP.

supported_method_errs

Number of unsupported methods requested by the application.

retries

Number of retransmitted messages.

late_responses

Number of messages that were decoded successfully but exceeded the timeout.

out_of_memory

Number of times that the client failed to allocate memory from Cisco IOS software.

mem_reallocs

Number of times that the client needed to readjust its buffer size because the server response message size exceeded the allocated buffer.

msg_malloced

Number of message buffers currently allocated for receiving messages from the server.

event_malloced

Number of event buffers currently allocated for application programming interface (API) requests.

cache_freed_by_ager

Number of HTTP client cache entries freed up by the background ager process.

clear http client statistics

Resets to zero all the counters that collect the information about the communication between the HTTP server and the client displayed in the output from the show http client statistics command.

slot

(Optional) Slot location of the port adapter.

port

(Optional) Port number on the port adapter.

dsp

DSP information.

number

(Optional) Number of DSP sets to show. Range is from 1 to 30.

long

(Optional) Detailed DSP information.

short

(Optional) Brief DSP information.

12.0(5)XE

This command was introduced on the Cisco 7200 series.

12.1(1)T

This command was integrated into Cisco IOS Release 12.1(1)T.

DSPfarm3/0 is up

DSPfarm interface is operating. The interface state can be up, down, or administratively down.

Line protocol is

Whether the software processes that handle the line protocol consider the line usable or if it has been taken down by an administrator.

Hardware

Version number of the hardware.

MTU

256 bytes.

BW

12000 kilobits.

DLY

Delay of the interface, in microseconds.

Reliability

Reliability of the interface as a fraction of 255 (255/255 is 100% reliability, calculated as an expediential average over 5 minutes).

Txload

Number of packets sent.

Rxload

Number of packets received.

Encapsulation

Encapsulation method assigned to the interface.

Loopback

Loopback conditions.

C549 DSP Firmware Version

Version of DSP firmware installed.

DSP Boot Loader

DSP boot loader version.

DSP Application

DSP application code version.

Medium Complexity Application

DSP Medium Complexity Application code version.

High Complexity Application

DSP High Complexity Application code version.

Total DSPs

Total DSPs that are equipped in the PA.

DSP0-DSP

DSP number range.

Jukebox DSP id

Jukebox DSP number.

Down DSPs

DSPs not in service.

Total sig channels...used...

Total number of signal channels used.

Total voice channels...used...

Total number of voice channels used.

Active calls

Number of active calls.

Max active calls

Maximum number of active calls.

Total calls

Total number of calls.

Rx packets

Number of received (rx) packets.

Rx drops

Number of rx packets dropped at PA.

Tx packets

Number of transmit (tx) packets.

Tx frags

Number of tx packets that were fragmented.

Curr_dsp_tx_queued

Number of tx packets that are being queued at host DSP queues.

Max_dsp_tx_queued

The max total tx packets that were queued at host DSP queues.

Last input

Number of hours, minutes, and seconds since the last packet was successfully received by an interface. Useful for knowing when a dead interface failed. This counter is updated only when packets are process switched and not when packets are fast switched.

Output

Number of hours, minutes, and seconds since the last packet was successfully sent by the interface. Useful for knowing when a dead interface failed. This counter is updated only when packets are process switched and not when packets are fast switched.

Output hang

Number of hours, minutes, and seconds (or never) since the interface was last reset because of a transmission that took too long. When the number of hours in any of the "last" fields exceeds 24 hours, the number of days and hours is printed. If that field overflows, asterisks (**) are printed.

Last clearing of "show interface" counters

Number of times the "show interface" counters were cleared.

queueing strategy

First-in, first-out queueing strategy (other queueing strategies you might see are priority-list, custom-list, and weighted fair).

Output queue

Number of packets in output queue.

Drops

Number of packets dropped because of a full queue.

Input queue

Number of packets in input queue.

Minute input rate

Average number of bits and packets received per minute in the past 5 minutes.

Bits/sec

Average number of bits sent per second.

Packets/sec

Average number of packets sent per second.

Packets input

Total number of error-free packets received by the system.

Bytes

Total number of bytes, including data and MAC encapsulation, in the error free packets received by the system.

No buffer

Number of received packets discarded because there was no buffer space in the main system. Compare with ignored count. Broadcast storms on Ethernets and bursts of noise on serial lines are often responsible for no-input-buffer events.

Received...broadcasts

Total number of broadcast or multicast packets received by the interface.

Runts

Number of packets that are discarded because they are smaller than the minimum packet size for the medium. For instance, any Ethernet packet that is less than 64 bytes is considered a runt.

Giants

Number of packets that are discarded because they exceed the maximum packet size for the medium. For instance, any Ethernet packet that is greater than 1518 bytes is considered a giant.

Throttles

Number of times the receiver on the port was disabled, possibly because of buffer or processor overload.

Input errors

Number of packet input errors.

CRC

Cyclic redundancy checksum generated by the originating LAN station or far end device does not match the checksum calculated from the data received. On a LAN, this usually indicates noise or transmission problems on the LAN interface or the LAN bus itself. A high number of CRCs is usually the result of collisions or a station sending bad data. On a serial link, CRCs usually indicate noise, gain hits, or other transmission problems on the data link.

Frame

Number of packets received incorrectly having a CRC error and a noninteger number of octets. On a serial line, this is usually the result of noise or other transmission problems.

Overrun

Number of times the serial receiver hardware was unable to hand received data to a hardware buffer because the input rate exceeded the ability of the receiver to handle the data.

Ignore

Number of received packets ignored by the interface because the interface hardware ran low on internal buffers. These buffers are different from the system buffers mentioned previously in the buffer description. Broadcast storms and bursts of noise can cause the ignored count to be incremented.

Abort

Illegal sequence of one bits on the interface.

Packets output

Total number of messages sent by the system.

Bytes

Total number of bytes, including data and MAC encapsulation, sent by the system.

Underruns

Number of times that the far end transmitter has been running faster than the near-end router's receiver can handle.

Output errors

Sum of all errors that prevented the final transmission of datagrams out of the interface being examined. Note that this value might not balance with the sum of the enumerated output errors; some datagrams can have more than one error, and others can have errors that do not fall into any of the specifically tabulated categories.

Collisions

Number of messages re-sent because of an Ethernet collision. Collisions are usually the result of an overextended LAN (Ethernet or transceiver cable too long, more than two repeaters between stations, or too many cascaded multiport transceivers). A packet that collides is counted only once in output packets.

Interface resets

Number of times an interface has been completely reset. Resetting can happen if packets queued for transmission were not sent within a certain interval. If the system notices that the carrier detect line of an interface is up, but the line protocol is down, it periodically resets the interface in an effort to restart it. Interface resets can also occur when an unrecoverable interface processor error occurs, or when an interface is looped back or shut down.

Output buffer failures

Number of failed buffers.

Output buffers swapped out

Number of buffers swapped out.

show interfaces

Displays statistics for all interfaces configured on the router or access server.

port

The port number.

12.4(11)T

This command was introduced.

HFC state is OPERATIONAL

Current HFC state on the modem.

HFC MAC address

The HFC MAC address for this modem.

Hardware is Cable modem

Hardware type.

Internet address

The IP address for this modem.

MTU

Total MTU usage in bytes, kilobits, user seconds. Describes reliability, transmit load, and receiver load.

Encapsulation ARPA, loopback not set

Encapsulation type and whether loopback is set.

ARP type: ARPA, ARP Timeout

ARP type and timeout parameters.

Last input, output, output hang

Most recent input and output statistics.

Last clearing of "show interface" counters

Most recent usage of show interface command counters.

Input queue, Total output drops

Input queue and output drop statistics in the following format: size/max/drops/flushes.

Queueing strategy: Class-based queueing

Queueing type. In this case, class-based queueing.

Output queue

Output queue statistics in the following format: size/max total/threshold/drops.

Conversations

Type and number of conversations in the following format: active/max active/max total.

Reserved Conversations

Number of reserved conversations in the following format: allocated/max allocated.

Available Bandwidth

Allotted bandwidth in kilobits per second.

input rate, packets

Input rate and number of packets in bits per second, packets per second.

output rate, packets

Output rate and number of packets in bits per second, packets per second.

HFC input, output

HFC input statistics in the following format: errors, discards, unknown protocols, flow control discards.

packets input

Number of packets in bytes, with or without buffer.

Received broadcasts, runts, giants, throttles

Number of broadcasts, runts, giants, and throttles.

input errors

Number and type of input errors in the following format: cyclic redundancy check (CRC), frame, overrun, ignored.

packets output

Number of packets output in bytes and underruns.

output errors, collisions, interface resets

Number of output errors, collisions, and interface resets.

babbles, late collision, deferred

Number of babbles, late collisions, and deferred packets.

lost carrier, no carrier

Carrier statistics.

output buffer failures, output buffers swapped out

Buffer statistics.

NOT_READY

Cable modem controller is resetting.

NOT_SYNCHRONIZED

Cable modem controller is starting the downstream frequency scan.

PHY_SYNCHRONIZED

Cable modem controller locked the downstream signal and is collecting the upstream channel parameter information.

US_PARAMETERS_ACQUIRED

Cable modem controller collected upstream channel parameter information and is trying to lock upstream frequency.

RANGING_COMPLETE

Cable modem controller received the CMTS range response, has finished downstream/upstream lock process, and is initializing IP.

IP_COMPLETE

Cable modem controller has IP information.

WAITING_FOR_DHCP_OFFER

Cable modem controller is sending a Dynamic Host Configuration Protocol (DHCP) request to the CMTS.

WAITING_FOR_DHCP_RESPONSE

Cable modem controller is waiting for a DHCP response from the CMTS.

WAITING_FOR_TIME_SERVER

Cable modem controller is starting the time of day (ToD) service.

TOD_ESTABLISHED

Cable modem controller has received the ToD packet and has synchronized its local time.

WAITING_FOR_TFTP

Cable modem controller is downloading its running configuration from the CMTS-defined TFTP server.

PARAM_TRANSFER_COMPLETE

Cable modem controller has completed transferring its running configuration.

REGISTRATION_COMPLETE

Cable modem controller has sent out its registration request, and CMTS has accepted it.

REFUSED_BY_CMTS

Cable modem controller registration request has been rejected by CMTS.

FORWARDING_DENIED

Cable modem controller registration to CMTS was successful, but network access is disabled in the running configuration.

OPERATIONAL

Cable modem controller is ready for service.

UNKNOWN

Cable modem controller is an undefined state

errors

The total number of input packets discarded on the cable modem controller.

discards

The number of input packets discarded due to a momentary lack of resources.

unknown protocols

The number of input packets discarded because they have unsupported or unknown protocol values.

flow control discards

The number of input packets discarded because the cable modem controller overflowed transferring packets to the router.

errors

Total number of output packets discarded on the cable modem controller.

discards

Total number of output packets discarded due to a momentary lack of resources.

show interfaces

Displays statistics for all interfaces.

all

Output displays information about all configured ASs.

name as-name

Name of a particular AS. Output displays information about just that AS.

12.2(4)T

This command was introduced.

12.2(8)T

This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.

12.2(11)T

This command was implemented on the Cisco 2420, Cisco 2600 series, Cisco 3600 series, Cisco 3700 series, Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850.

Name of AS: 1

Name of the AS.

Total num of ASPs configured :2

asp1
asp2

Total number of application server processes (ASPs) configured.

Current state : ACTIVE

The possible states are ACTIVE, INACTIVE, and DOWN.

Active ASP :asp1

Shows the active ASP.

Number of ASPs up :1

If two ASPs are up, then the one that is not active is in standby mode.

Fail-Over time : 4000 milliseconds

Default is 4000 ms, although the value can also be configured through the CLI under AS.

Local address list : 10.1.2.345 10.2.3.456

Configured by the user.

Local port:2139

Configured by the user.

Interface IDs registered with this AS

Interface id

0 (Dchannel0)

3 (Dchannel3)

2 (Dchannel2)

1 (Dchannel1)

The D channels that are bound to this AS.

clear ip sctp statistics

Clears statistics counts for SCTP.

show ip sctp association list

Displays a list of all current SCTP associations.

show ip sctp association parameters

Displays the parameters configured for the association defined by the association ID.

show ip sctp association statistics

Displays the current statistics for the association defined by the association ID.

show ip sctp errors

Displays error counts logged by SCTP.

show ip sctp instances

Displays the currently defined SCTP instances.

show ip sctp statistics

Displays the overall statistics counts for SCTP.

show isdn

Displays information about memory, Layer 2 and Layer 3 timers, and the status of PRI channels.

show iua asp

Displays information about the current condition of an ASP.

all

Displays information about all configured ASPs.

name asp-name

Name of a particular ASP. Displays information about just that ASP.

12.2(4)T

This command was introduced.

12.2(8)T

This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.

12.2(11)T

This command was implemented on the Cisco AS5300.

12.2(15)T

This command was integrated into Cisco IOS Release 12.2(15)T on the Cisco 2420, Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series; and Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 network access server (NAS) platforms.

Name of ASP: 1

Name of the application server process (ASP).

Current State of ASP: ASP-Active

The possible states are ACTIVE, INACTIVE, and DOWN.

Current state of underlying SCTP Association IUA_ASSOC_ESTAB , assoc id 0

States used for underlying SCTP association: IUA_ASSOC_ESTAB (association established) or IUA_ASSOC_INIT (association not established...attempting to initiate).

SCTP Association information :

Local Receive window :9000

Remote Receive window :9000

Configured by the user.

Primary Dest address requested by IUA 10.11.2.33

The IP address through which the current link is established.

Remote address list :10.22.3.44

Remote Port :9900

Configured by the user.

Statistics :

Invalid SCTP signals Total :0 Since last 0

SCTP Send failures :0

Information useful for seeing if errors are happening with the SCTP connection.

clear ip sctp statistics

Clears statistics counts for SCTP.

show ip sctp association list

Displays a list of all current SCTP associations.

show ip sctp association parameters

Displays the parameters configured for the association defined by the association ID.

show ip sctp association statistics

Displays the current statistics for the association defined by the association ID.

show ip sctp errors

Displays error counts logged by SCTP.

show ip sctp instances

Displays the currently defined SCTP instances.

show ip sctp statistics

Displays the overall statistics counts for SCTP.

show iua as

Displays information about the current condition of an AS.

12.3(8)T

This command was introduced.

MTP

Displays the profile numbers configured for MTP resources.

TRANSCODING

Displays the profile numbers configured for transcoding resources.

CONFERENCING

Displays the profile numbers configured for conferencing resources.

Status

Displays the current status of the profile.

dsp services dspfarm

Configures DSP farm services for a specified voice card.

dspfarm profile

Enters DSP farm profile configuration mode and defines a profile for DSP farm services.

show dspfarm profile

Displays configured DSP farm profile information for a Cisco CallManager group.

slot

Specifies the slot number of the card to be displayed. Valid values are from 1 to 4.

conference

(Optional) Displays information on ad-hoc conferences.

connections

(Optional) Displays information on media card connections.

dsp number

(Optional) Displays information on the specified DSP resource pool. The number argument ranges in value from 1 to 4.

12.3(8)XY

This command was introduced on the Communication Media Module.

12.3(14)T

This command was integrated into Cisco IOS Release 12.3(14)T.

12.4(3)

This command was integrated into Cisco IOS Release 12.4(3).

RxPkts

Number of packets transmitted

TxPkts

Number of packets received

RPort

Receiving port

SPort

Sending port

Remote-Ip

IP address of the remote endpoint

debug mediacard

Displays debugging information for DSPRM.

connection

(Optional) Displays the active MGCP-controlled connections.

endpoint

(Optional) Displays the MGCP-controlled endpoints.

nas

(Optional) Displays Network Access Server (NAS) information.

dump

(Optional) Display MGCP data channel data.

slot

(Optional) Slot number.

port

(Optional) Port number.

chan-number

(Optional) Channel number.

info

(Optional) Displays MGCP data channel information.

notify-entity

(Optional) Displays MGCP notify entity information.

profile [name]

(Optional) Displays information about all the configured MGCP profiles.

•name—Displays information about the specified MGCP profile.

statistics

(Optional) Displays MGCP statistics regarding received and transmitted network messages.

12.1(1)T

This command was introduced on the Cisco AS5300.

12.1(3)T

This command was modified. Command output was updated to display additional gateway and platform information.

12.1(5)XM

This command was modified. Command output was updated to display additional gateway and platform information.

12.2(2)T

This command was implemented on the Cisco 7200 series.

12.2(2)XA

This command was modified. The profile keyword was added.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T.

12.2(2)XB

This command was modified. Command output was enhanced to display the status of MGCP system resource check (SRC) call admission control (CAC) and Service Assurance Agent (SA Agent) CAC. (See the Cisco IOS Release 12.2(2)XB document MGCP VoIP Call Admission Control.)

The nas dump slot port channel and nas info keywords and arguments were added. Because the number of keywords increased, the command page for the show mgcp command was separated into the following command pages:

•show mgcp

•show mgcp connection

•show mgcp endpoint

•show mgcp nas

•show mgcp profile

•show mgcp statistics

12.2(8)T

This command was integrated into Cisco IOS Release 12.2(8)T.

12.2(2)XN

This command was modified. Support for enhanced MGCP voice gateway interoperability was added to Cisco CallManager Version 3.1 for the Cisco 2600 series, Cisco 3600 series, and Cisco VG200 routers.

12.2(11)T

This command was integrated into Cisco IOS Release 12.2(11)T and Cisco CallManager Version 2.0. It was implemented on the Cisco AS5350, Cisco AS5400, Cisco AS5850, and Cisco IAD2420 series. The MGCP SGCP RSIP field was enhanced to show the status of the mgcp sgcp disconnected notify command.

12.2(13)T

This command was modified. Support was added for MGCP.

12.2(15)T

This command was implemented on Cisco 1751 and Cisco 1760 routers.

12.2(15)ZJ

This command was integrated into Cisco IOS Release 12.2(15)ZJ on the Cisco 26xxXM, Cisco 2691, Cisco 3640, Cisco 3640A, Cisco 3660, and Cisco 37xx routers.

12.3(2)T

This command was implemented on the Cisco 26xxXM, Cisco 2691, Cisco 3640, Cisco 3640A, Cisco 3660, and Cisco 37xx routers.

12.3(11)T

This command was modified. Command output was enhanced to display the enabled Secure Real-Time Transport Protocol (SRTP) package and enabled MGCP call-agent validation.

12.4(2)T

This command was modified. Command output was enhanced to display State Signaling Events (SSE) and Simple Packet Relay Transport (SPRT) configuration parameters.

12.4(11)T

This command was modified. The show mgcp command output was enhanced to display comedia-related configuration.

15.1(4)M

This command was integrated into Cisco IOS 15.1(4)M. The command output was enhanced to displays the configuration of the tone-package keyword in the MGCP- supported packages.

MGCP Admin State...Oper State

Administrative and operational state of the MGCP daemon. The administrative state controls the starting and the stopping of the application using the mgcp and mgcp block-newcalls commands. The operational state controls the normal MGCP operations.

MGCP call-agent

Address of the call agent specified in the mgcp call-agent or call-agent command and the protocol initiated for this session.

MGCP block-newcalls

State of the mgcp block-newcalls command.

MGCP send SGCP RSIP, disconnected

Setting for the mgcp sgcp restart notify and the mgcp sgcp disconnected notify commands (enabled or disabled).

MGCP quarantine mode

How the quarantine buffer is to handle Simple Gateway Control Protocol (SGCP) events.

MGCP quarantine of persistent events is

Specifies whether the SGCP persistent events are handled by the quarantine buffer.

MGCP dtmf-relay

Setting for the mgcp dtmf-relay command.

MGCP voip modem passthrough

Settings for mode, codec, and redundancy from the mgcp modem passthrough mode, mgcp modem passthrough codec, and mgcp modem passthrough voip redundancy commands.

MGCP voip mdste modem relay

Settings for the mgcp modem relay voip sprt v14 receive playback, mgcp modem relay voip sprt v14 transmit maximum hold-count, mgcp modem relay voip sprt v14 transmit hold-time, mgcp modem relay voip sprt retries, mgcp modem relay voip sse redundancy, and mgcp modem relay voip sse t1 commands.

SPRT rx v14 hold time

Setting for the mgcp modem relay voip sprt v14 receive playback hold-time time command.

SPRT tx v14 hold count

Setting for the mgcp modem relay voip sprt v14transmit maximum hold-count characters command.

SPRT tx v14 hold time

Setting for the mgcp modem relay voip sprt v14 transmit hold-time time command.

SPRT Retries

Setting for the mgcp modem relay voip sprt retries command.

SSE redundancy interval

Setting for the mgcp modem relay voip mode sse redundancy interval time command.

SSE redundancy packet

Setting for the mgcp modem relay voip mode sse redundancy packet command.

SSE t1 timer

Setting for the mgcp modem relay voip mode sse redundancy t1 command.

SSE retries

Setting for the mgcp modem relay voip mode sse redundancy retries command.

MGCP Comedia role

Location of gateway:

•ACTIVE—inside NAT

•PASSIVE—outside NAT

MGCP Comedia check media source

Global media IP and port address detection status (ENABLED or DISABLED).

MGCP Comedia sdp force

Configuration state of forced insertion of the direction attribute in the SDP (ENABLED or DISABLED)

MGCP TSE payload

Setting for the mgcp tse payload command.

MGCP Network (IP/AAL2) Continuity Test timer

Setting for the net-cont-test keyword in the mgcp timer command.

MGCP `RTP stream loss' timer

Setting for the receive-rtcp keyword in the mgcp timer command.

MGCP request timeout

Setting for the mgcp request timeout command.

MGCP maximum exponential request timeout

Setting for the mgcp request timeout max command.

MGCP gateway port

UDP port specification for the gateway.

MGCP maximum waiting delay

Setting for the mgcp max-waiting-delay command.

MGCP restart delay

Setting for the mgcp restart-delay command.

MGCP vad

Setting for the mgcp vad command.

MGCP rtrcac

Specifies whether MGCP SA Agent CAC has been enabled with the mgcp rtrcac command.

MGCP system resource check

Specifies whether MGCP SRC CAC has been enabled with the mgcp src-cac command.

MGCP xpc-codec

Specifies whether the mgcp sdp xpc-codec command has been configured to generate the X-pc codec field for Session Description Protocol (SDP) codec negotiation in Network-Based Call Signaling (NCS) and Trunking Gateway Control Protocol (TGCP).

MGCP persistent hookflash

Specifies whether the mgcp persistent hookflash command has been configured to send persistent hookflash events to the call agent.

MGCP persistent offhook

Specifies whether the mgcp persistent offhook command has been configured to send persistent off-hook events to the call agent.

MGCP persistent onhook

Specifies whether the mgcp persistent onhook command has been configured to send persistent on-hook events to the call agent.

MGCP piggyback msg

Specifies whether the mgcp piggyback message command has been configured to enable piggyback messaging.

MGCP endpoint offset

Specifies whether the mgcp endpoint offset command has been configured to enable incrementing of the local portion of an endpoint name for NCS. The local portion contains the analog or digital voice port identifier.

MGCP simple-sdp

Specifies whether the mgcp sdp simple command has been configured to enable simple mode SDP operation.

MGCP undotted-notation

Specifies whether the mgcp sdp notation undotted command has been configured to enable undotted SDP notation for the codec string.

MGCP codec type

Setting for the mgcp codec command.

MGCP packetization period

The packetization period parameter setting for the mgcp codec command.

MGCP JB threshold lwm

Jitter-buffer minimum-threshold parameter setting for the mgcp quality-threshold command.

MGCP JB threshold hwm

Jitter-buffer maximum-threshold parameter setting for the mgcp quality-threshold command.

MGCP LAT threshold lwm

Latency minimum-threshold parameter setting for the mgcp quality-threshold command.

MGCP LAT threshold hwm

Latency maximum-threshold parameter setting for the mgcp quality-threshold command.

MGCP PL threshold lwm

Packet-loss minimum-threshold parameter setting for the mgcp quality-threshold command.

MGCP PL threshold hwm

Packet-loss maximum-threshold parameter setting for the mgcp quality-threshold command.

MGCP CL threshold lwm

Cell-loss minimum-threshold parameter setting for the mgcp quality-threshold command.

MGCP CL threshold hwm

Cell-loss maximum-threshold parameter setting for the mgcp quality-threshold command.

MGCP playout mode is

Jitter-buffer packet type and size.

MGCP default package

Package configured as the default package with the mgcp default-package command.

MGCP supported packages

Packages configured with the mgcp package-capability command to be supported on this gateway in this session. The Line Control Signaling Package (lcs-package) display is new in Cisco IOS Release 12.3(8)T.

MGCP voaal2 modem passthrough

Settings for mode, codec, and redundancy from the mgcp modem passthrough mode and mgcp modem passthrough codec commands.

MGCP T.38 Fax

Settings for the mgcp fax t.38 command. The following values are displayed:

•MGCP T.38 fax: ENABLED or DISABLED.

•Error correction mode (ECM): ENABLED or DISABLED.

•Nonstandard facilities (NSF) override: ENABLED or DISABLED. If enabled, the override code is displayed.

•MGCP T.38 fax low-speed redundancy: the factor set on the gateway for redundancy.

•MGCP T.38 fax high-speed redundancy: the factor set on the gateway for redundancy.

ccm-manager config

Supplies the local MGCP voice gateway with the IP address or logical name of the TFTP server from which to download XML configuration files and enable the download of the configuration.

debug ccm-manager

Displays debugging information about the Cisco CallManager.

debug mgcp

Enables debug traces for MGCP errors, events, media, packets, and parser.

isdn bind-l3 (interface BRI)

Configures the BRI to support MGCP and to bind ISDN Layer 3 with Cisco CallManager backhaul.

mgcp

Allocates resources for the MGCP and starts the daemon.

mgcp behavior comedia-check-media-src

Enables IP address and port detection from the first RTP packet received for the entire MGCP gateway.

mgcp behavior comedia-role

Indicates the location of the MGCP gateway.

mgcp behavior comedia-sdp-force

Forces the SDP to place the direction attribute in the SDP using the command as a reference.

mgcp package-capability mdste-package

Specifies the MGCP package capability type for a media gateway.

security password-group

Defines the passwords used by gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.

show ccm-manager

Displays a list of Cisco CallManager servers and their current statuses, and availability.

show ccm-manager fallback-mgcp

Displays the status of the MGCP gateway fallback feature.

show mgcp connection

Displays information for active MGCP-controlled connections.

show mgcp endpoint

Displays information for MGCP-controlled endpoints.

show mgcp nas

Displays MGCP NAS information for data ports.

show mgcp profile

Displays values for MGCP profile-related parameters.

show mgcp statistics

Displays MGCP statistics regarding received and transmitted network messages.

12.1(1)T

The show mgcp command was introduced on the Cisco AS5300.

12.1(3)T

The show mgcp command output was updated to display additional gateway and platform information.

12.1(5)XM

The show mgcp command output was updated to display additional gateway and platform information.

12.2(2)T

The show mgcp command was implemented on the Cisco 7200 series and was integrated into Cisco IOS Release 12.2(2)T.

12.2(2)XA

The profile keyword was added.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T.

12.2(2)XB

Output for the show mgcp command was enhanced to display the status of MGCP System Resource Check (SRC) Call Admission Control (CAC) and Service Assurance Agent (SA Agent) CAC. (Refer to the Cisco IOS Release 12.2(2) XB online document MGCP VoIP Call Admission Control.)

The nas dump slot port channel and nas info keywords and arguments were added. Because the number of keywords increased, the command page for the show mgcp command was separated into the following command pages:

•show mgcp

•show mgcp connection

•show mgcp endpoint

•show mgcp nas

•show mgcp profile

•show mgcp statistics

12.2(8)T

This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.

12.2(11)T

Support was added for the Cisco AS5300, Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850.

12.3(11)T

Command output was enhanced to display the encryption suite used on the Secure Real-Time Transport Protocol (SRTP) connection.

12.4(2)T

Command output was enhanced to display the current media state.

12.4(11)T

Command output was enhanced to display the detected NAT address and port.

Endpoint

Endpoint for each call shown in the digital endpoint naming convention of slot number (S0) and digital line (DS1-0) number (1).

Call_ID(C)

MGCP call ID sent by the call agent, the internal Call Control Application Programming Interface (CCAPI) call ID for this endpoint, and the CCAPI call ID of the peer call legs.

(CCAPI is an API that provides call control facilities to applications.)

(COM)Addr/Port

Detected media address and port.

Conn_ID(I)

Connection ID generated by the gateway and sent in the ACK message.

(P)ort

Ports used for this connection. The first port is the local User Datagram Protocol (UDP) port. The second port is the remote UDP port.

(V)cci/cid

Virtual channel connection identifier (VCCI) and channel identifier (CID) used for the VoAAL2 call.

(Me)dia

Media state, where:

•0—Voice

•1—Modem pass-through

•2—Modem relay

(M)ode

Call mode, where:

•0—Invalid value for mode.

•1—Gateway should only send packets.

•2—Gateway should only receive packets.

•3—Gateway should send and receive packets.

•4—Gateway should neither send nor receive packets.

•5—Gateway should place the circuit in loopback mode.

•6—Gateway should place the circuit in test mode.

•7—Gateway should use the circuit for network access for data.

•8—Gateway should place the connection in network loopback mode.

•9—Gateway should place the connection in network continuity test mode.

•10—Gateway should place the connection in conference mode.

All other values are used for internal debugging.

(S)tate

Call state. The values are used for internal debugging purposes.

(Co)dec

Codec identifier. The values are used for internal debugging purposes.

(E)vent [SIFL]

Used for internal debugging.

(R)esult [EA]

Used for internal debugging.

Encryption(K)

Encryption suite, where:

•0—None

•1—AES_CM_128_HMAC_SHA1_32

debug mgcp

Enables debug traces for MGCP errors, events, media, packets, and parser.

mgcp

Allocates resources for the MGCP and starts the daemon.

mgcp behavior comedia-check-media-src

Enables ip address and port detection from the first rtp packet received for the entire MGCP gateway.

mgcp behavior comedia-role

Indicates the location of the MGCP gateway.

mgcp behavior comedia-sdp-force

Forces the SDP to place the direction attribute in the SDP using the command as a reference.

security password-group

Defines the passwords used by gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.

show mgcp

Displays values for MGCP parameters.

show mgcp endpoints

Displays information for MGCP-controlled endpoints.

show mgcp nas

Displays MGCP NAS information for data ports.

show mgcp profile

Displays values for MGCP profile-related parameters.

show mgcp statistics

Displays MGCP statistics regarding received and transmitted network messages.

12.1(1)T

The show mgcp command was introduced on the Cisco AS5300.

12.1(3)T

The show mgcp command output was updated to display additional gateway and platform information.

12.1(5)XM

The show mgcp command output was updated to display additional gateway and platform information.

12.2(2)T

The show mgcp command was implemented on the Cisco 7200 series and this command was integrated into Cisco IOS Release 12.2(2)T.

12.2(2)XA

The profile keyword was added to the show mgcp command.

12.2(4)T

This command was integrated into Cisco IOS Release 12.2(4)T.

12.2(2)XB

The output for the show mgcp command was enhanced to display the status of MGCP System Resource Check (SRC) Call Admission Control (CAC) and Service Assurance Agent (SA Agent) CAC. (Refer to the Cisco IOS Release 12.2(2) XB online document MGCP VoIP Call Admission Control.)

In addition, the nas dump slot port channel and nas info keywords and arguments were added to the show mgcp command. Because the number of keywords increased, the command-reference page for the show mgcp command was separated into the following command-reference pages:

•show mgcp

•show mgcp connection

•show mgcp endpoint

•show mgcp nas

•show mgcp profile

•show mgcp statistics

12.2(8)T

This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.

12.2(11)T

This command is supported on the Cisco AS5300, Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850 in this release.

ENDPOINT-NAME

Name used by the call agent to identify a specific mgcp endpoint on a given gateway.

V-PORT

Voice port

SIG-TYPE

Signaling type for a given endpoint (for example, NONE for SS7 ISDN User Part (ISUP) and FXS-GS for Foreign Exchange Station (FXS) Ground Start).

ADMIN

Administrative status—Up or Down. (This field is populated only on residential gateway (RGW) platforms.

debug mgcp

Enables debug traces for MGCP errors, events, media, packets, and parser.

mgcp

Allocates resources for the MGCP and starts the daemon.

security password-group

Defines the passwords used by gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.

show mgcp

Displays information for MGCP parameters.

show mgcp connection

Displays information for active MGCP-controlled connections.

show mgcp nas

Displays MGCP NAS information for data ports.

show mgcp profile

Displays values for MGCP profile-related parameters.

show mgcp statistics

Displays MGCP statistics regarding received and transmitted network messages.

dump slot port channel

Displays NAS information for the specified port and channel. The arguments are as follows:

•slot—Chassis slot for interface card. Values are as follows:

–Cisco AS5350: From 0 to 3.

–Cisco AS5400: From 0 to 7.

–Cisco AS5850: From 0 to 5 and from 8 to 13. Slots 6 and 7 are reserved for the route switch controller (RSC).

•port—Modem interface port. Values are as follows:

–Cisco AS5350: For T1/E1, from 0 to 7. For T3, from 1 to 28.

–Cisco AS5400: For T1/E1, from 0 to 7. For T3, from 1 to 28.

–Cisco AS5850: For T1/E1, from 0 to 23. For T3, from 1 to 28.

•channel—T1 or E1 channel. Values for T1 are from 1 to 24. Values for E1 are from 1 to 31.