- A
- B
- cac master through call application stats
- call application voice through call denial
- call fallback through called-number (dial peer)
- caller-id (dial peer) through ccm-manager switchover-to-backup
- ccs connect (controller) through clear vsp statistics
- clid through credentials (sip-ua)
- default (auto-config application) through direct-inward-dial
- disable-early-media through dualtone
- E
- F
- G
- H
- icpif through irq global-request
- isdn bind-l3 through ixi transport http
- K
- L
- map q850-cause through mgcp package-capability
- mgcp persistent through mmoip aaa send-id secondary
- mode (ATM/T1/E1 controller) through mwi-server
- N
- O
- package through pattern
- periodic-report interval through proxy h323
- Q
- R
- sccp through service-type call-check
- session through sgcp tse payload
- show aal2 profile through show call filter match-list
- show call history fax through show debug condition
- show dial-peer through show gatekeeper zone prefix
- show gateway through show modem relay statistics
- show mrcp client session active through show sip dhcp
- show sip service through show trunk hdlc
- show vdev through show voice statistics memory-usage
- show voice trace through shutdown (voice-port)
- signal through srv version
- ss7 mtp2-variant through switchover method
- target carrier-id through timeout tsmax
- timeouts call-disconnect through timing clear-wait
- timing delay-duration through type (voice)
- U
- vad (dial peer) through voice-class sip encap clear-channel
- voice-class sip error-code-override through vxml version 2.0
- W
- Z
- show mrcp client session active
- show mrcp client session history
- show mrcp client statistics hostname
- show mwi relay clients
- show nextport
- show nextport vpd
- show num-exp
- show piafs status
- show pots csm
- show pots status
- show pots volume
- show presence global
- show presence subscription
- show proxy h323 calls
- show proxy h323 detail-call
- show proxy h323 status
- show raw
- show rawmsg
- show rlm group statistics
- show rlm group status
- show rlm group timer
- show rpms-proc counters
- show rtpspi
- show rtsp client session
- show rudpv0 failures
- show rudpv0 statistics
- show rudpv1
- show sccp
- show sccp ccm group
- show sccp connections details
- show sccp connections internal
- show sccp connections rsvp
- show sccp connections summary
- show sccp server statistics
- show sdspfarm
- show settlement
- show sgcp connection
- show sgcp endpoint
- show sgcp statistics
- show shared-line
- show sip dhcp
show mrcp client session active
To display information about active Media Resource Control Protocol (MRCP) client sessions, use the show mrcp client session active command in privileged EXEC mode.
show mrcp client session active [detailed]
Syntax Description
detailed |
(Optional) Displays detailed information about each active MRCP session. |
Command Modes
Privileged EXEC
Command History
Usage Guidelines
Use this command to display information about all active MRCP sessions for the gateway. Use the detailed keyword to display additional information about the sessions.
Examples
The following is sample output from this command:
Router# show mrcp client session active
No Of Active MRCP Sessions:1
Call-ID:0x1A
Resource Type:Synthesizer URL:rtsp://server-asr/synthesizer
Method In Progress:SPEAK State:SPEAKING
Resource Type:Recognizer URL:rtsp://server-asr/recognizer
Method In Progress:RECOGNIZE State:RECOGNIZING
The following is sample output when the detailed keyword is used:
Router# show mrcp client session active detailed
No Of Active MRCP Sessions: 1
Call-ID: 0x14 same: 0
--------------------------------------------
Resource Type: Synthesizer URL: sip:mrcpv2TTSServer@10.5.18.224
Method In Progress: SPEAK State: S_SYNTH_IDLE
Associated CallID: 0x17
MRCP version: 2.0
Control Protocol: TCP Server IP Address: 10.5.18.224 Port: 51000
Data Protocol: RTP Server IP Address: 10.5.18.224 Port: 10000
Stream URL: sip:mrcpv2TTSServer@10.5.18.224:5060
Packets Transmitted: 0 (0 bytes)
Packets Received: 177 (28320 bytes)
ReceiveDelay: 100 LostPackets: 0
--------------------------------------------
--------------------------------------------
Resource Type: Recognizer URL: sip:mrcpv2ASRServer@10.5.18.224
Method In Progress: RECOGNITION-START-TIMERS State: S_RECOG_RECOGNIZING
Associated CallID: 0x18
MRCP version: 2.0
Control Protocol: TCP Server IP Address: 10.5.18.224 Port: 51001
Data Protocol: RTP Server IP Address: 10.5.18.224 Port: 10002
Packets Transmitted: 191 (30560 bytes)
Packets Received: 0 (0 bytes)
ReceiveDelay: 100 LostPackets: 0
Table 136 describes the fields shown in this output.
Related Commands
show mrcp client session history
To display information about past Media Resource Control Protocol (MRCP) client sessions that are stored on the gateway, use the show mrcp client session history command in privileged EXEC mode.
show mrcp client session history [detailed]
Syntax Description
detailed |
(Optional) Displays detailed information about each MRCP session. |
Command Modes
Privileged EXEC
Command History
Usage Guidelines
The maximum number of inactive MRCP sessions that are stored in history is configured by using the mrcp client session history records command. If the mrcp client session history records command is not used, the maximum number of history records that are saved is 50.
MRCP history records are stored for the length of time that is specified by the mrcp client session history duration command. If the mrcp client session history duration command is not configured, MRCP history records are stored for a maximum of 3600 seconds (1 hour).
Examples
The following is sample output from this command:
Router# show mrcp client session history
MRCP Session ID:0x9
Associated CallID:0x1A
Control Protocol:TCP Data Protocol:RTP
Local IP Address:10.1.2.230 Local Port 17120
Server IP Address:10.1.2.58 Server Port 4858
Stream URL:rtsp://server-asr:554
Packets Transmitted:423 (101520 bytes)
Packets Received:819 (131040 bytes)
MRCP Session ID:0x8
Associated CallID:0x16
Control Protocol:TCP Data Protocol:RTP
Local IP Address:10.1.2.230 Local Port 16948
Server IP Address:10.1.2.58 Server Port 4850
Stream URL:rtsp://server-asr:554
Packets Transmitted:284 (68160 bytes)
Packets Received:598 (95680 bytes)
MRCP Session ID:0x7
Associated CallID:0x12
Control Protocol:TCP Data Protocol:RTP
Local IP Address:10.1.2.230 Local Port 16686
Server IP Address:10.1.2.58 Server Port 4842
Stream URL:rtsp://server-asr:554
Packets Transmitted:353 (84720 bytes)
Packets Received:716 (114560 bytes)
MRCP Session ID:0x6
Associated CallID:0xE
Control Protocol:TCP Data Protocol:RTP
Local IP Address:10.1.2.230 Local Port 19398
Server IP Address:10.1.2.58 Server Port 4834
Stream URL:rtsp://server-asr:554
Packets Transmitted:358 (85920 bytes)
Packets Received:720 (115200 bytes)
The following is sample output from the show mrcp client session history detailed command:
Router# show mrcp client session history detailed
MRCP Session ID: 0x7
Associated CallID: 0x14
MRCP version: 2.0
=================
Control Protocol: TCP Data Protocol: RTP
ASR (Callid = 0x18)
Server IP Address: 10.5.18.224 Server Port 10002
Signalling URL: sip:mrcpv2ASRServer@10.5.18.224:5060
Packets Transmitted: 373 (59680 bytes)
Packets Received: 0 (0 bytes)
OntimeRcvPlayout: 3000
GapFillWithSilence: 0
GapFillWithPrediction: 0
GapFillWithInterpolation: 6025
GapFillWithRedundancy: 0
HighWaterPlayoutDelay: 100
LoWaterPlayoutDelay: 95
ReceiveDelay: 100 LostPackets: 0
EarlyPackets: 0 LatePackets: 0
-----------------------------------------
TTS (Callid = 0x17)
Server IP Address: 10.5.18.224 Server Port 10000
Signalling URL: sip:mrcpv2TTSServer@10.5.18.224:5060
Packets Transmitted: 0 (0 bytes)
Packets Received: 679 (108640 bytes)
OntimeRcvPlayout: 3000
GapFillWithSilence: 0
GapFillWithPrediction: 0
GapFillWithInterpolation: 6025
GapFillWithRedundancy: 0
HighWaterPlayoutDelay: 100
LoWaterPlayoutDelay: 95
ReceiveDelay: 100 LostPackets: 0
EarlyPackets: 0 LatePackets: 0
Table 137 describes the fields shown in this output.
Related Commands
show mrcp client statistics hostname
To display statistics about Media Resource Control Protocol (MRCP) sessions for a specific MRCP client host, use the show mrcp client statistics hostname command in privileged EXEC mode.
show mrcp client statistics hostname {hostname | ip-address}
Syntax Description
hostname |
Hostname of the MRCP server. Format uses host name only or hostname:port. |
ip-address |
IP address of the MRCP server. |
Command Modes
Privileged EXEC
Command History
Usage Guidelines
To display output from this command, you must first use the mrcp client statistics enable command.
Examples
The following is sample output from this command:
Router# show mrcp client statistics hostname asr-host
hostname:asr-host
Method :Count Min Avg Max
RECOGNIZE :3 40 562 1604
DEFINE-GRAMMAR :3 48 568 1604
RECOGNITION-START-TIMERS :2 140 164 188
SPEAK :6 44 568 1596
RECOG-TIME :3 804 965 1128
SPEAK-TIME :6 3636 7063 12068
Table 138 describes the fields shown in this output.
Related Commands
show mwi relay clients
To display registration information for the list of message-waiting indicator (MWI) relay clients, use the show mwi relay clients command in EXEC mode.
show mwi relay clients
Syntax Description
This command has no arguments or keywords.
Command Modes
EXEC
Command History
Examples
The following is sample output from this command:
Router# show mwi relay clients
Client IPADDR EXPIRES(sec) MWI
============ =============== ============ ====
4085558653 10.8.17.25 89077 ON
6505556543 10.8.17.34 87654 OFF
Table 139 describes significant fields shown in this output.
|
|
|
|---|---|
Client |
Client number. |
IPADDR |
IP address. |
EXPIRES |
Seconds before expiration. |
MWI |
MWI status. |
Related Commands
|
|
|
|---|---|
mwi relay |
Enables the Cisco IOS Telephony Service router to relay MWI information to remote Cisco IP phones. |
show nextport
To display statistical information on NextPort digital signal processor (DSP) resources for diagnostic and debugging purposes, use the show nextport command in privileged EXEC mode.
show nextport {dfc slot/port | est [slot/dfc/module | enabled] | ifd {queue slot/port [control | data | est | gdb | voice | npaddress [qid]] | statistics} | md modem | mm [slot/dfc/module | interrupt] | np-address slot/port | session {slot/port | tty ttynumber} | siglib test | ssm {info slot/port | test | vdev slot/port } | test | vpd {statistics [slot/port ] | traffic slot/port} | vsmgr protocol violations}
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
The show nextport command is intended to be used by Cisco Technical Support personnel to look at the NextPort DSP statistics and to perform detailed debugging. Please consult Cisco Technical Support before using this command.
The show nextport command is supported on the Cisco AS5300XM series, Cisco AS5400XM series, and Cisco AS5800XM series platforms.
When you enter the show nextport vpd statistics command on the Cisco AS5850, the output shows the TX/RX packet counters that could not be forwarded by distributed Cisco Express Forwarding. These packets are routed back to the enhanced route switch controller (ERSC).
The show nextport vpd statistics slot/port command (on individual feature boards) displays the TX/RX packet counts for the packets that have been forwarded by distributed Cisco Express Forwarding.
The display of packet counts for the packets forwarded on the Cisco AS5850 is the result of the distributed architecture of the platform.
Examples
The following examples show some of the variations of the show nextport command.
Note 
Field descriptions in the examples provided are self-explanatory.
Router# show nextport session 1/1
Session Information Display
slot/port : 1/1 TTY# : 217 Session ID : 0x006D
Module Address : Slot 1 DFC 0 Module 0 SPE 0 Channel 1
Service Type : DATA FAX MODEM
Session State : IDLE
TDM Information:
DSP is connected to TDM stream 0, channel 1 on the NextPort module
Router# show nextport vpd statistics
Voice Statistics for slot 1
Status: Active
Rx Statistics
rx_successful= 0
rx_failed= 0
queue destroyed = 0
buffer pool depleted = 0
invalid packet = 0
wrong session packet = 0
rejection by dsp api layer = 0
Tx Statistics
tx_successful= 0
tx_acked_by_ifd= 0
tx_failed= 0
rejection by IFD = 0
Voice Statistics for slot 2
Status: Idle
Rx Statistics
rx_successful= 0
rx_failed= 0
queue destroyed = 0
buffer pool depleted = 0
invalid packet = 0
wrong session packet = 0
rejection by dsp api layer = 0
Tx Statistics
tx_successful= 0
tx_acked_by_ifd= 0
tx_failed= 0
rejection by IFD = 0
Voice Statistics for slot 3
Status: Active
Rx Statistics
rx_successful= 0
rx_failed= 0
queue destroyed = 0
buffer pool depleted = 0
invalid packet = 0
wrong session packet = 0
rejection by dsp api layer = 0
Tx Statistics
tx_successful= 0
tx_acked_by_ifd= 0
tx_failed= 0
rejection by IFD = 0
Voice Statistics for slot 4
Status: Idle
Rx Statistics
rx_successful= 0
rx_failed= 0
queue destroyed = 0
buffer pool depleted = 0
invalid packet = 0
wrong session packet = 0
rejection by dsp api layer = 0
Tx Statistics
tx_successful= 0
tx_acked_by_ifd= 0
tx_failed= 0
rejection by IFD = 0
Voice Statistics for slot 5
Status: Idle
Rx Statistics
rx_successful= 0
rx_failed= 0
queue destroyed = 0
buffer pool depleted = 0
invalid packet = 0
wrong session packet = 0
rejection by dsp api layer = 0
Tx Statistics
tx_successful= 0
tx_acked_by_ifd= 0
tx_failed= 0
rejection by IFD = 0
Voice Statistics for slot 6
Status: Idle
Rx Statistics
rx_successful= 0
rx_failed= 0
queue destroyed = 0
buffer pool depleted = 0
invalid packet = 0
wrong session packet = 0
rejection by dsp api layer = 0
Tx Statistics
tx_successful= 0
tx_acked_by_ifd= 0
tx_failed= 0
rejection by IFD = 0
Voice Statistics for slot 7
Status: Idle
Rx Statistics
rx_successful= 0
rx_failed= 0
queue destroyed = 0
buffer pool depleted = 0
invalid packet = 0
wrong session packet = 0
rejection by dsp api layer = 0
Tx Statistics
tx_successful= 0
tx_acked_by_ifd= 0
tx_failed= 0
rejection by IFD = 0
Router# show nextport ssm vdev 3/1
vdev_common handle @ 0xC0D92E20
slot 3, port 1, tone , device_status(0): VDEV_STATUS_UNLOCKED
csm_state(0x0100)=CSM_IDLE_STATE, csm_event_proc=0x601EA0C0
invalid_event_count=2, wdt_timeout_count=0
wdt_timestamp_started is not activated
wait_for_dialing:False, wait_for_bchan:False
pri_chnl=TDM_ISDN_STREAM(s0, u0, c0), tdm_chnl=TDM_DSP_STREAM(s3, c1)
dchan_idb_start_index=0, dchan_idb_index=0, call_id=0x0000, bchan_num=-1
csm_event=CSM_EVENT_MODEM_ONHOOK, cause=0x0007
ring_no_answer=0, ic_failure=0, ic_complete=0
dial_failure=0, oc_failure=0, oc_complete=0
oc_busy=0, oc_no_dial_tone=0, oc_dial_timeout=0
remote_link_disc=0, stat_busyout=0
oobp_failure=0, cas_address_signalling_failure=0
call_duration_started=00:00:00, call_duration_ended=00:00:00, total_call_durati0
The calling party phone number =
The called party phone number =
total_free_rbs_timeslot = 0, total_busy_rbs_timeslot = 0, total_rtr_busy_rbs_ti,
total_sw56_rbs_timeslot = 0, total_sw56_rbs_static_bo_ts = 0,
total_free_isdn_channels = 0, total_auto_busy_isdn_channels = 0,
total_rtr_busy_isdn_channels = 0,
min_free_device_threshold = 0
Router# show nextport mm
IOS bundled NextPort image version: 0.0.0.0
NP Module(3 ): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(4 ): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(5 ): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(6 ): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(7 ): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(8 ): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(9 ): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(10): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(11): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 7.37.10.90
NP Module(12): slot=4, dfc=0, module=0
state = MODULE RUNNING
crash=0, bad=0, restarts=0, num SPEs=6
max_mpt_redundancy_session = 18
spe country code = 0
session handle enable = TRUE
IOS bundled NextPort image version: 7.37.10.90
NP Module(13): slot=4, dfc=0, module=1
state = MODULE RUNNING
crash=0, bad=0, restarts=0, num SPEs=6
max_mpt_redundancy_session = 18
spe country code = 0
session handle enable = TRUE
IOS bundled NextPort image version: 7.37.10.90
NP Module(14): slot=4, dfc=0, module=2
state = MODULE RUNNING
crash=0, bad=0, restarts=0, num SPEs=6
max_mpt_redundancy_session = 18
spe country code = 0
session handle enable = TRUE
IOS bundled NextPort image version: 7.37.10.90
NP Module(15): slot=5, dfc=0, module=0
state = MODULE RUNNING
crash=0, bad=0, restarts=0, num SPEs=6
max_mpt_redundancy_session = 18
spe country code = 0
session handle enable = TRUE
IOS bundled NextPort image version: 7.37.10.90
NP Module(16): slot=5, dfc=0, module=1
state = MODULE RUNNING
crash=0, bad=0, restarts=0, num SPEs=6
max_mpt_redundancy_session = 18
spe country code = 0
session handle enable = TRUE
IOS bundled NextPort image version: 7.37.10.90
NP Module(17): slot=5, dfc=0, module=2
state = MODULE RUNNING
crash=0, bad=0, restarts=0, num SPEs=6
max_mpt_redundancy_session = 18
spe country code = 0
session handle enable = TRUE
IOS bundled NextPort image version: 0.0.0.0
NP Module(18): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(19): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(20): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(21): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(22): state = MODULE NOT INSERTED
IOS bundled NextPort image version: 0.0.0.0
NP Module(23): state = MODULE NOT INSERTED
Related Commands
|
|
|
|---|---|
show voice dsp |
Displays the current status or selective statistics of DSP voice channels. |
show nextport vpd
To display the TX/RX packet counters for voice packet drivers (VPDs) (including success and failure statistics), use the show nextport vpd command in privileged EXEC mode.
show nextport vpd {statistics [slot/port-number]| traffic [slot/port-number]}
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
15.0(1)M |
This command was introduced in a release earlier than Cisco IOS Release 15.0(1)M. |
Usage Guidelines
The show nextport vpd statistics command displays the TX/RX packet counters that could not be forwarded by distributed Cisco Express Forwarding (dCEF). These packets are routed back to the enhanced route switch controller (ERSC). Executing show nextport vpd statistics slot/port (on individual feature boards) shows the TX/RX packet counts for the packets that have been forwarded by dCEF.
Examples
The following is sample output from the show nextport vpd traffic command for slot1 ans port1:
Router# show nextport vpd traffic 1/1
Voice Instance for slot 1 port 1
Status: Idle
Session Duration in second: 0
Rx traffic Statistics
total rx bytes: 0
total rx packets: 0
average rx packets per second: 0
Tx traffic Statistics
total tx bytes: 0
total tx packets: 0
average tx packets per second: 0
Table 140 describes the significant fields shown in the display.
The following is sample output from the show nextport vpd statistics command. The field descriptions are self-explanatory.
Router# show nextport vpd statistics
Voice Instance for slot 1 port 1
Status: Idle
Rx Statistics
rx_successful= 0
rx_failed= 0
queue destroyed = 0
buffer pool depleted = 0
invalid packet = 0
wrong session packet = 0
Tx Statistics
tx_successful= 0
tx_acked_by_ifd= 0
tx_failed= 0
rejection by IFD = 0
show num-exp
To display the number expansions configured, use the show num-exp command in privileged EXEC mode.
show num-exp [dialed-number]
Syntax Description
dialed-number |
(Optional) Dialed number. |
Command Modes
Privileged EXEC
Command History
Usage Guidelines
Use this command to display all the number expansions configured for this router. To display number expansion for only one number, specify that number by using the dialed-number argument.
Examples
The following is sample output from this command:
Router# show num-exp
Dest Digit Pattern = '0...' Translation = '+14085270...'
Dest Digit Pattern = '1...' Translation = '+14085271...'
Dest Digit Pattern = '3..' Translation = '+140852703..'
Dest Digit Pattern = '4..' Translation = '+140852804..'
Dest Digit Pattern = '5..' Translation = '+140852805..'
Dest Digit Pattern = '6....' Translation = '+1408526....'
Dest Digit Pattern = '7....' Translation = '+1408527....'
Dest Digit Pattern = '8...' Translation = '+14085288...'
Table 141 describes significant fields shown in this output.
Related Commands
show piafs status
To display the status of Personal Handyphone System (PHS) Internet Access Forum Standard (PIAFS) calls for each B channel in use on a router, use the show piafs status command in privileged EXEC mode.
show piafs status
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.2(8)T |
This command was introduced on the Cisco 803, Cisco 804, and Cisco 813. |
Examples
The following is sample output from this command showing the status of PIAFS calls on B channel 1 on a Cisco 813 router:
Router# show piafs status
PIAFS STATUS INFORMATION
-------------------------
Number of active calls = 1
Details of connection 1
************************
Call Direction is: INCOMING
Call speed is: 64K
Current speed is: 64K
Call Elapsed Time: 59 seconds
The B channel assigned for this call is: B1 CHAN
Control Parameters Agreed Upon:
ARQ Control Information Transfer Protocol: Version 1
ARQ Data Transmission Protocol: Version 1
Measured RTF value: 9
PIAFS Frame Length in Bytes: 80
Maximum Frame Number: 63
Data Transmission Protocol of Peer: FIXED SPEED
Data Transmission Protocol of 800 Router: FIXED SPEED
V42 Negotiated: YES
V42 Parameters:
Direction: BOTH
No of code words: 4096
Max string length: 250
First PPP Frame Detected: YES
Piafs main FSM state: PIAFS_DATA
PIAFS Data Frames Tx Statistics:
Total No: of PIAFS Frames Confirmed: 344
Total Bytes of Application Data Transmitted:
Before Compression: 47021
After Compression: 30952
Compression Ratio in Tx direction is 1.51: 1
Total No: of PIAFS Frames Retransmitted: 32
Total Bytes of Application Data Retransmitted: 2336
Total Throughput in Tx Direction:
Including PIAFS Dummy Frames: 8000 Bytes/Second
Excluding PIAFS Dummy Frames: 859 Bytes/Second
Excluding PIAFS Dummy and Retransmitted Data Frames: 593 Bytes/Second
PIAFS Data Frames Rx Statistics:
Total No: of PIAFS Frames Received: 86
Total No: of Bad PIAFS Frames Received: 0
Total Bytes of Application Data Received:
Before Uncompression: 1459
After Uncompression: 2955
Compression Ratio in Rx direction is 2.02: 1
Total Throughput in Rx Direction:
Including PIAFS Dummy Frames: 8000 Bytes/Second
Excluding PIAFS Dummy Frames: 656 Bytes/Second
Excluding PIAFS Dummy and Retransmitted Data Frames: 126 Bytes/Second
No: of ReSynchronizations so far: 0
Table 142 describes significant fields shown in this output.
Related Commands
|
|
|
|---|---|
debug piafs events |
Displays debugging messages for PIAFS calls. |
show pots csm
To display the current state of calls and the most recent event received by the call-switching module (CSM) on a Cisco 800 series router, use the show pots csm command in privileged EXEC mode.
show pots csm port
Syntax Description
port |
Port number. Range is from 1 to 2. |
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.1.(2)XF |
This command was introduced on the Cisco 800 series. |
Examples
The following is sample output from this command:
Router# show pots csm 1
POTS PORT: 1
CSM Finite State Machine:
Call 0 - State: idle, Call Id: 0x0
Active: no
Event: CSM_EVENT_NONE Cause: 0
Call 1 - State: idle, Call Id: 0x0
Active: no
Event: CSM_EVENT_NONE Cause: 0
Call 2 - State: idle, Call Id: 0x0
Active: no
Event: CSM_EVENT_NONE Cause: 0
Field descriptions should be self-explanatory.
Related Commands
show pots status
To display the settings of the telephone port physical characteristics and other information on the telephone interfaces of a Cisco 800 series router, use the show pots status command in privileged EXEC mode.
show pots status [1 | 2]
Syntax Description
1 |
(Optional) Displays the settings of telephone port 1. |
2 |
(Optional) Displays the settings of telephone port 2. |
Command Default
No default behavior or values
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.0(3)T |
This command was introduced on the Cisco 800 series. |
Examples
The following is sample output from this command.
Router# show pots status
POTS Global Configuration:
Country: United States
Dialing Method: Overlap, Tone Source: Remote, CallerId Support: YES
Line Type: 600 ohm, PCM Encoding: u-law, Disc Type: OSI,
Ringing Frequency: 20Hz, Distinctive Ring Guard timer: 0 msec
Disconnect timer: 1000 msec, Disconnect Silence timer: 5 sec
TX Gain: 6dB, RX Loss: -6dB,
Filter Mask: 6F
Adaptive Cntrl Mask: 0
POTS PORT: 1
Hook Switch Finite State Machine:
State: On Hook, Event: 0
Hook Switch Register: 10, Suspend Poll: 0
CODEC Finite State Machine:
State: Idle, Event: 0
Connection: None, Call Type: Two Party, Direction: Rx only
Line Type: 600 ohm, PCM Encoding: u-law, Disc Type: OSI,
Ringing Frequency: 20Hz, Distinctive Ring Guard timer: 0 msec
Disconnect timer: 1000 msec, Disconnect Silence timer: 5 sec
TX Gain: 6dB, RX Loss: -6dB,
Filter Mask: 6F
Adaptive Cntrl Mask: 0
CODEC Registers:
SPI Addr: 2, DSLAC Revision: 4
SLIC Cmd: 0D, TX TS: 00, RX TS: 00
Op Fn: 6F, Op Fn2: 00, Op Cond: 00
AISN: 6D, ELT: B5, EPG: 32 52 00 00
SLIC Pin Direction: 1F
CODEC Coefficients:
GX: A0 00
GR: 3A A1
Z: EA 23 2A 35 A5 9F C2 AD 3A AE 22 46 C2 F0
B: 29 FA 8F 2A CB A9 23 92 2B 49 F5 37 1D 01
X: AB 40 3B 9F A8 7E 22 97 36 A6 2A AE
R: 01 11 01 90 01 90 01 90 01 90 01 90
GZ: 60
ADAPT B: 91 B2 8F 62 31
CSM Finite State Machine:
Call 0 - State: idle, Call Id: 0x0
Active: no
Call 1 - State: idle, Call Id: 0x0
Active: no
Call 2 - State: idle, Call Id: 0x0
Active: no
POTS PORT: 2
Hook Switch Finite State Machine:
State: On Hook, Event: 0
Hook Switch Register: 20, Suspend Poll: 0
CODEC Finite State Machine:
State: Idle, Event: 0
Connection: None, Call Type: Two Party, Direction: Rx only
Line Type: 600 ohm, PCM Encoding: u-law, Disc Type: OSI,
Ringing Frequency: 20Hz, Distinctive Ring Guard timer: 0 msec
Disconnect timer: 1000 msec, Disconnect Silence timer: 5 sec
TX Gain: 6dB, RX Loss: -6dB,
Filter Mask: 6F
Adaptive Cntrl Mask: 0
CODEC Registers:
SPI Addr: 3, DSLAC Revision: 4
SLIC Cmd: 0D, TX TS: 00, RX TS: 00
Op Fn: 6F, Op Fn2: 00, Op Cond: 00
AISN: 6D, ELT: B5, EPG: 32 52 00 00
SLIC Pin Direction: 1F
CODEC Coefficients:
GX: A0 00
GR: 3A A1
Z: EA 23 2A 35 A5 9F C2 AD 3A AE 22 46 C2 F0
B: 29 FA 8F 2A CB A9 23 92 2B 49 F5 37 1D 01
X: AB 40 3B 9F A8 7E 22 97 36 A6 2A AE
R: 01 11 01 90 01 90 01 90 01 90 01 90
GZ: 60
ADAPT B: 91 B2 8F 62 31
CSM Finite State Machine:
Call 0 - State: idle, Call Id: 0x0
Active: no
Call 1 - State: idle, Call Id: 0x0
Active: no
Call 2 - State: idle, Call Id: 0x0
Active: no
Time Slot Control: 0
Table 143 describes significant fields shown in this output.
Related Commands
show pots volume
To display the receiver volume level that is configured for each POTS port on a router, use the show pots volume command in privileged EXEC mode.
show pots volume
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.2(8)T |
This command was introduced on the Cisco 803, Cisco 804, and Cisco 813. |
Examples
The following is sample output from this command showing that the receiver volume level is 5 for both POTS port 1 and POTS port 2.
Router# show pots volume
POTS PORT 1: Volume 5
POTS PORT 2: Volume 5
Field descriptions should be self-explanatory.
Related Commands
|
|
|
|---|---|
volume |
Configures the receiver volume level for a POTS port on a router. |
show presence global
To display configuration information about the presence service, use the show presence global command in user EXEC or privileged EXEC mode.
show presence global
Syntax Description
This command has no arguments or keywords.
Command Modes
User EXEC
Privileged EXEC
Command History
|
|
|
|---|---|
12.4(11)XJ |
This command was introduced. |
12.4(15)T |
This command was integrated into Cisco IOS Release 12.4(15)T. |
Usage Guidelines
This command displays the configuration settings for presence.
Examples
The following example displays output from the show subscription global command:
Router# show subscription global
Presence Global Configuration Information:
=============================================
Presence feature enable : TRUE
Presence allow external watchers : FALSE
Presence max subscription allowed : 100
Presence number of subscriptions : 0
Presence allow external subscribe : FALSE
Presence call list enable : TRUE
Presence server IP address : 0.0.0.0
Presence sccp blfsd retry interval : 60
Presence sccp blfsd retry limit : 10
Presence router mode : CME mode
Table 144 describes the significant fields shown in the display.
Related Commands
show presence subscription
To display information about active presence subscriptions, use the show presence subscription command in user EXEC or privileged EXEC mode.
show presence subscription [details | presentity telephone-number | subid subscription-id | summary]
Syntax Description
Command Default
Information for all active presence subscriptions is displayed.
Command Modes
User EXEC
Privileged EXEC
Command History
|
|
|
|---|---|
12.4(11)XJ |
This command was introduced. |
12.4(15)T |
This command was integrated into Cisco IOS Release 12.4(15)T. |
Usage Guidelines
This command displays details about the currently active presence subscriptions
Examples
The following is sample output from the show presence subscription details command:
Presence Active Subscription Records Details:
=============================================
Subscription ID : 1
Watcher : 6002@10.4.171.60
Presentity : 6005@10.4.171.34
Expires : 3600 seconds
Subscription Duration : 1751 seconds
line status : idle
watcher type : local
presentity type : local
Watcher phone type : SIP Phone
subscription type : Incoming Indication
retry limit : 0
sibling subID : 0
sdb : 0
dp : 6555346C
watcher dial peer tag : 40001
number of presentity : 1
Subscription ID : 2
Watcher : 6002@10.4.171.60
Presence Active Subscription Records:
=============================================
Subscription ID : 30
Watcher : 4085256003@10.4.171.34
Presentity : 5001@10.4.171.20
Expires : 3600 seconds
line status : idle
watcher type : local
presentity type : remote
Watcher phone type : SCCP [BLF Call List]
subscription type : Outgoing Request
retry limit : 0
sibling subID : 23
sdb : 0
dp : 0
watcher dial peer tag : 0
The following is sample output from the show presence subscription summary command:
Router# show presence subscription summary
Presence Active Subscription Records Summary: 15 subscription
Watcher Presentity SubID Expires SibID Status
======================== ======================== ====== ======= ====== ======
6002@10.4.171.60 6005@10.4.171.34 1 3600 0 idle
6005@10.4.171.81 6002@10.4.171.34 6 3600 0 idle
6005@10.4.171.81 6003@10.4.171.34 8 3600 0 idle
6005@10.4.171.81 6002@10.4.171.34 9 3600 0 idle
6005@10.4.171.81 6003@10.4.171.34 10 3600 0 idle
6005@10.4.171.81 6001@10.4.171.34 12 3600 0 idle
6001@10.4.171.61 6003@10.4.171.34 15 3600 0 idle
6001@10.4.171.61 6002@10.4.171.34 17 3600 0 idle
6003@10.4.171.59 6003@10.4.171.34 19 3600 0 idle
6003@10.4.171.59 6002@10.4.171.34 21 3600 0 idle
6003@10.4.171.59 5001@10.4.171.34 23 3600 24 idle
6002@10.4.171.60 6003@10.4.171.34 121 3600 0 idle
6002@10.4.171.60 5002@10.4.171.34 128 3600 129 idle
6005@10.4.171.81 1001@10.4.171.34 130 3600 131 busy
6005@10.4.171.81 7005@10.4.171.34 132 3600 133 idle
The following is sample output from the show presence subscription subid command:
Router# show presence subscription subid 133
Presence Active Subscription Records:
=============================================
Subscription ID : 133
Watcher : 6005@10.4.171.34
Presentity : 7005@10.4.171.20
Expires : 3600 seconds
line status : idle
watcher type : local
presentity type : remote
Watcher phone type : SIP Phone
subscription type : Outgoing Request
retry limit : 0
sibling subID : 132
sdb : 0
dp : 0
watcher dial peer tag : 0
Table 144 describes the significant fields shown in the display.
Related Commands
show proxy h323 calls
To display a list of active calls on the proxy, use the show proxy h323 calls command in privileged EXEC mode.
show proxy h323 calls
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
11.3(2)NA |
This command was introduced. |
12.0(3)T |
The command was integrated into Cisco IOS Release 12.0(3)T and implemented on the Cisco MC3810. |
Examples
The following is sample output from this command:
Router# show proxy h323 calls
Call unique key = 1
Conference ID = [277B87C0A283D111B63E00609704D8EA]
Calling endpoint call signalling address = 55.0.0.41
Calling endpoint aliases:
H323_ID: ptel11@zone1.com
Call state = Media Streaming
Time call was initiated = 731146290 ms
Field descriptions should be self-explanatory.
Related Commands
|
|
|
|---|---|
show proxy h323 detail-call |
Displays the details of a particular call on a proxy. |
show proxy h323 status |
Displays the overall status of a proxy. |
show proxy h323 detail-call
To display the details of a particular call on a proxy, use the show proxy h323 detail-call command in privileged EXEC mode.
show proxy h323 detail-call call-key
Syntax Description
call-key |
Call to be displayed, derived from the show proxy h323 calls command output. |
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
11.3(2)NA |
This command was introduced. |
12.0(3)T |
The command was integrated into Cisco IOS Release 12.0(3)T and implemented on the Cisco MC3810. |
Usage Guidelines
You can use this command with or without proxy statistics enabled.
Examples
The following is sample output from this command without proxy statistics enabled:
Router# show proxy h323 detail-call 1
ConferenceID = [277B87C0A283D111B63E00609704D8EA]
Calling endpoint aliases:
H323_ID: ptel11@zone1.com
Called endpoint aliases:
H323_ID: ptel21@zone2.com
Peer proxy call signalling address = 172.17.0.41
Time call was initiated = 731146290 ms
Inbound CRV = 144
Outbound CRV = 70
Call state = Media Streaming
H245 logical channels for call leg pte111@zone1.com<->px1@zone.com
Channel number = 2
Type = VIDEO
State = OPEN
Bandwidth = 374 kbps
Time created = 731146317 ms
Channel number = 1
Type = AUDIO
State = OPEN
Bandwidth = 81 kbps
Time created = 731146316 ms
Channel number = 2
Type = VIDEO
State = OPEN
Bandwidth = 374 kbps
Time created = 731146318 ms
Channel number = 1
Type = AUDIO
State = OPEN
Bandwidth = 81 kbps
Time created = 731146317 ms
H245 logical channels for call leg pte111@zone1.com<->172.17.50.21:
Channel number = 2
Type = VIDEO
State = OPEN
Bandwidth = 374 kbps
Time created = 731146317 ms
Channel number = 1
Type = AUDIO
State = OPEN
Bandwidth = 81 kbps
Time created = 731146316 ms
Channel number = 2
Type = VIDEO
State = OPEN
Bandwidth = 374 kbps
Time created = 731146318 ms
Channel number = 1
Type = AUDIO
State = OPEN
Bandwidth = 81 kbps
Time created = 731146317 ms
The following is sample output from this command with proxy statistics enabled:
Router# show proxy h323 detail-call 1
ConferenceID = [677EB106BD0D111976200002424F832]
Calling endpoint call signalling address = 172.21.127.49
Calling endpoint aliases:
H323_ID: intel2
E164_ID: 2134
Called endpoint aliases:
H323_ID: mcs@sanjose.cisco.com
Peer proxy call signalling address = 172.68.183.199
Peer proxy aliases:
H323_ID: proxy.sanjose.cisco.com
Time call was initiated = 730949651 ms
Inbound CRV = 2505
Outbound CRV = 67
Call state = H245 open logical channels
H245 logical channels for call leg intel2 <-> cisco7-pxy:
Channel number = 259
RTP stream from intel2 to cisco7-pxy
Type = VIDEO
State = OPEN
Bandwidth = 225 kbps
Time created = 730949676 ms
Channel number = 257
RTP stream from intel2 to cisco7-pxy
Type = AUDIO
State = OPEN
Bandwidth = 18 kbps
Time created = 730949658 ms
Channel number = 2
RTP stream from cisco7-pxy to intel2
Type = VIDEO
State = OPEN
Bandwidth = 225 kbps
Time created = 730949664 ms
RTP Statistics:
Packet Received Count = 3390
Packet Dropped Count = 0
Packet Out of Sequence Count = 0
Number of initial packets used for Arrival-Spacing bin setup = 200
min_arrival_spacing = 0(ms) max_arrival_spacing = 856(ms)
Average Arrival Rate = 86(ms)
Arrival-Spacing(ms) Packet-Count
0 2116
26 487
52 26
78 0
104 0
130 1
156 0
182 1
208 0
234 4
260 99
286 315
312 154
338 8
364 0
390 2
416 10
442 73
468 51
494 43
==============================
Min Jitter = 34(ms) Max Jitter = 408(ms)
Average Jitter Rate = 117
Jitter Rate(ms) Packet-Count
0 0
41 514
82 2117
Number of initial packets used for Arrival-Spacing bin setup = 200
min_arrival_spacing = 32(ms) max_arrival_spacing = 96(ms)
Average Arrival Rate = 60(ms)
Arrival-Spacing(ms) Packet-Count
32 35
34 0
36 177
38 0
40 56
42 0
44 10
46 0
48 27
50 0
52 541
54 0
56 2642
58 1
60 1069
62 0
64 77 0
68 6
70 257
==============================
Min Jitter = 0(ms) Max Jitter = 28(ms)
Average Jitter Rate = 5
Jitter Rate(ms) Packet-Count
0 1069
3 2720
6 0
9 804
12 27
15 10
18 0
21 56
24 177
27 35
H245 logical channels for call leg cisco7-pxy <->
proxy.sanjose.cisco.com:
Channel number = 259
RTP stream from cisco7-pxy to proxy.sanjose.cisco.com
Type = VIDEO
State = OPEN
Bandwidth = 225 kbps
Time created = 730949676 ms
RTP Statistics:
Packet Received Count = 3398
Packet Dropped Count = 1
Packet Out of Sequence Count = 0
Number of initial packets used for Arrival-Spacing bin setup = 200
min_arrival_spacing = 0(ms) max_arrival_spacing = 872(ms)
Average Arrival Rate = 85(ms)
Arrival-Spacing(ms) Packet-Count
0 2636
28 0
56 0
84 0
112 0
140 1
168 0
196 0
224 0
252 0
280 2
308 425
336 154
364 5
392 0
420 0
448 0
476 114
504 41
532 20
==============================
Min Jitter = 55(ms) Max Jitter = 447(ms)
Average Jitter Rate = 127
Jitter Rate(ms) Packet-Count
0 0
45 1
90 2636
135 0
180 2
225 425
270 159
315 0
360 0
405 175
Channel number = 257
RTP stream from cisco7-pxy to proxy.sanjose.cisco.com
Type = AUDIO
State = OPEN
Bandwidth = 18 kbps
Time created = 730949658 ms
RTP Statistics:
Packet Received Count = 2537
Packet Dropped Count = 3
Packet Out of Sequence Count = 0
Number of initial packets used for Arrival-Spacing bin setup = 200
min_arrival_spacing = 0(ms) max_arrival_spacing = 32716(ms)
Average Arrival Rate = 112(ms)
Arrival-Spacing(ms) Packet-Count
0 2191
72 253
144 31
216 7
288 3
360 4
432 4
504 2
576 1
648 3
720 2
792 1
864 2
936 1
1008 1
1080 1
1152 1
1224 1
1296 0
1368 28
==============================
Min Jitter = 32(ms) Max Jitter = 1256(ms)
Average Jitter Rate = 121
Jitter Rate(ms) Packet-Count
0 284
126 2201
252 4
378 6
504 4
630 3
756 2
882 2
1008 2
1134 29
Channel number = 2
RTP stream from proxy.sanjose.cisco.com to cisco7-pxy
Type = VIDEO
State = OPEN
Bandwidth = 225 kbps
Time created = 730949664 ms
Channel number = 1
RTP stream from proxy.sanjose.cisco.com to cisco7-pxy
Type = AUDIO
State = OPEN
Bandwidth = 18 kbps
Time created = 730949661 ms
Field descriptions should be self-explanatory.
Related Commands
|
|
|
|---|---|
h323 qos |
Enables QoS on the proxy. |
show proxy h323 calls |
Displays a list of active calls on the proxy. |
show proxy h323 status |
Displays the overall status of a proxy. |
show proxy h323 status
To display the overall status of a proxy, use the show proxy h323 status command in privileged EXEC mode.
show proxy h323 status
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
11.3(2)NA |
This command was introduced. |
12.0(3)T |
The command was integrated into Cisco IOS Release 12.0(3)T and implemented on the Cisco MC3810. |
Examples
The following is sample output from this command:
Router# show proxy h323 status
H.323 Proxy Status
==================
H.323 Proxy Mode: Enabled
Proxy interface = Serial1: UP
Application Specific Routing: Disabled
RAS Initialization: Complete
Proxy aliases configured:
H323_ID: px2
Proxy aliases assigned by Gatekeeper:
H323_ID: px2
Gatekeeper multicast discovery: Disabled
Gatekeeper:
Gatekeeper ID: gk.zone2.com
IP address: 70.0.0.31
Gatekeeper registration succeeded
T.120 Mode: BYPASS
RTP Statistics: OFF
Number of calls in progress: 1
Field descriptions should be self-explanatory.
Related Commands
|
|
|
|---|---|
show proxy h323 calls |
Displays a list of active calls on the proxy. |
show proxy h323 detail-call |
Displays the details of a particular call on a proxy. |
show raw
To display leaking raw buffers that have been captured, use the show raw command in privileged EXEC mode.
show raw {all | cas | ccapi | h323 | ivr | reclaimed | tsp | vtsp}
Syntax Description
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.2(2)XU3 |
This command was introduced. |
12.2(11)T |
This command was integrated into Cisco IOS Release 12.2(11)T. |
Usage Guidelines
The number of raw leaks that are displayed by the show raw reclaimed command should be zero, indicating that there are no memory leaks.
Examples
The following is a sample output from this command showing that there are no leaking raw buffers:
Router# show raw reclaimed
RAW LEAK REPORT:
ORPHAN : 0 raw buffers reclaimed
TSP : 0 raw buffers reclaimed
VTSP : 0 raw buffers reclaimed
H323 : 0 raw buffers reclaimed
SIP : 0 raw buffers reclaimed
CCAPI : 0 raw buffers reclaimed
VOATM : 0 raw buffers reclaimed
XGCP : 0 raw buffers reclaimed
CAS : 0 raw buffers reclaimed
IVR : 0 raw buffers reclaimed
SSAPP : 0 raw buffers reclaimed
Last Audit Session is at 20:28:13 UTC Fri Mar 27 2002
Table 146 describes significant fields shown in this output.
Related Commands
|
|
|
|---|---|
show rawmsg |
Shows raw messages owned by the required component. |
show rawmsg
To display the raw messages owned by the required component, use the show rawmsg command in privileged EXEC mode.
show rawmsg {all | cas | ccapi | h323 | ivr | reclaimed | tsp | vtsp}
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
The number displayed for the show rawmsg all command should be zero to indicate that there are no memory leaks.
Examples
The following is a sample output from the show rawmsg tsp command that displays memory leaks from the Telephony Service Provider. The field names are self-explanatory.
Router# show rawmsg tsp
Raw Msg Summary:
Raw Msg in used: 0
Related Commands
show rlm group statistics
To display the network latency of a Redundant Link Manager (RLM) group, use the show rlm group statistics command in privileged EXEC mode.
show rlm group [group-number] statistics
Syntax Description
group-number |
(Optional) RLM group number. The range is from 0 to 255. There is no default value. |
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
11.3(7) |
This command was introduced. |
12.4(22)T |
This command was integrated into Cisco IOS Release 12.4(22)T. |
Usage Guidelines
You can specify the group-number argument to view the network latency of a specific RLM group. If you do not specify the group-number argument, then the show rlm group statistics command displays the network latency of all the configured RLM groups.
Examples
The following is sample output from the show rlm group statistics command:
Router# show rlm group statistics
RLM Group Statistics
Link_up:
last time occurred at 02:45:48.724, total transition=1
avg=00:00:00.000, max=00:00:00.000, min=00:00:00.000, latest=00:00:00.000
Link_down:
last time occurred at 02:42:33.724, total transition=1
avg=00:03:15.000, max=00:03:15.000, min=00:00:00.000, latest=00:03:15.000
Link_recovered:
last time occurred at 00:00:00.000, success=0(0%), failure=0
avg=0.000s, max=0.000s, min=0.000s, latest=0.000s
Link_switched:
last time occurred at 00:00:00.000, success=0(0%), failure=0
avg=0.000s, max=0.000s, min=0.000s, latest=0.000s
Server_changed:
last time occurred at 00:00:00.000 for totally 0 times
Server Link Group[r1-server]:
Open the link [10.1.1.1(Loopback1), 10.1.4.1]:
last time occurred at 02:43:03.724, success=1(100%), failure=0
avg=162.000s, max=162.000s, min=0.000s, latest=162.000s
Echo over link [10.1.1.1(Loopback1), 10.1.4.1]:
last time occurred at 02:47:15.724, success=91(62%), failure=54
avg=0.000s, max=0.000s, min=0.000s, latest=0.000s
Open the link [10.1.1.2(Loopback2), 10.1.4.2]:
last time occurred at 02:43:03.724, success=1(100%), failure=0
avg=162.000s, max=162.000s, min=0.000s, latest=162.000s
Echo over link [10.1.1.2(Loopback2), 10.1.4.2]:
last time occurred at 02:47:19.724, success=95(63%), failure=54
avg=0.000s, max=0.000s, min=0.000s, latest=0.000s
Server Link Group[r2-server]:
Open the link [10.1.1.1(Loopback1), 10.1.5.1]:
last time occurred at 02:46:06.724, success=0(0%), failure=1
avg=0.000s, max=0.000s, min=0.000s, latest=0.000s
Echo over link [10.1.1.1(Loopback1), 10.1.5.1]:
last time occurred at 02:47:18.724, success=0(0%), failure=85
avg=0.000s, max=0.000s, min=0.000s, latest=0.000s
Open the link [10.1.1.2(Loopback2), 10.1.5.2]:
last time occurred at 02:46:06.724, success=0(0%), failure=1
avg=0.000s, max=0.000s, min=0.000s, latest=0.000s
Echo over link [10.1.1.2(Loopback2), 10.1.5.2]:
last time occurred at 02:47:18.724, success=0(0%), failure=85
avg=0.000s, max=0.000s, min=0.000s, latest=0.000s
Table 147 describes the significant fields shown in the display.
Related Commands
show rlm group status
To display the status of a Redundant Link Manager (RLM) group, use the show rlm group status command in privileged EXEC mode.
show rlm group [group-number] status
Syntax Description
group-number |
(Optional) RLM group number. The range is from 0 to 255. There is no default value. |
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
11.3(7) |
This command was introduced. |
12.4(22)T |
This command was integrated into Cisco IOS Release 12.4(22)T. |
Usage Guidelines
You can specify the group-number argument to view the status of a specific RLM group. If you do not specify the group-number argument, then the show rlm group status command displays the status of all the configured RLM groups.
Examples
The following is sample output from the show rlm group status command:
Router# show rlm group status
RLM Group 1 Status
User/Port: RLM_MGR/3000
Link State: Up Last Link Status Reported: Up
Next tx TID: 1 Last rx TID: 0
Server Link Group[r1-server]:
link [10.1.1.1(Loopback1), 10.1.4.1] = socket[active]
link [10.1.1.2(Loopback2), 10.1.4.2] = socket[standby]
Server Link Group[r2-server]:
link [10.1.1.1(Loopback1), 10.1.5.1] = socket[opening]
link [10.1.1.2(Loopback2), 10.1.5.2] = socket[opening]
Table 148 describes the significant fields shown in the display.
Related Commands
show rlm group timer
To display the current timer values of a Redundant Link Manager (RLM) group, use the show rlm group timer command in privileged EXEC mode.
show rlm group [group-number] timer
Syntax Description
group-number |
(Optional) RLM group number. The range is from 0 to 255. There is no default value. |
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
11.3(7) |
This command was introduced. |
12.4(22)T |
This command was integrated into Cisco IOS Release 12.4(22)T. |
Usage Guidelines
You can specify the group-number argument to view the timer values of a specific RLM group. If you do not specify the group-number argument, then the show rlm group timer command displays the timer values of all the configured RLM groups.
Examples
The following is sample output from the show rlm group timer command:
Router# show rlm group timer
RLM Group 1 Timer Values
open_wait = 3s force-down = 30s
recovery = 12s switch-link = 5s
minimum-up = 60s retransmit = 1s
keepalive = 1s
Table 149 describes the significant fields shown in the display.
Related Commands
show rpms-proc counters
To display statistics for the number of leg 3 authentication, authorization, and accounting (AAA) preauthentication requests, successes, and rejects, use the show rpms-proc counters command in privileged EXEC mode.
show rpms-proc counters
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.2(11)T |
This command was introduced. |
Usage Guidelines
Leg 3 refers to a call segment from the IP network to a terminating (outgoing) gateway that takes traffic from an IP network to a PSTN network.
Examples
The following sample output displays leg 3 statistics for AAA preauthentication requests, successes, and rejects:
Router# show rpms-proc counters
H323 Calls
Preauth Requests Sent : 43433
Preauth Requests Accepted : 43433
Preauth Requests Rejected : 0
Preauth Requests TimedOut : 0
Disconnects during Preauth : 0
SIP Calls
Preauth Requests Sent : 43080
Preauth Requests Accepted : 43080
Preauth Requests Rejected : 0
Preauth Requests TimedOut : 0
Disconnects during Preauth : 0
Table 150 describes significant fields shown in this output.
Related Commands
|
|
|
|---|---|
clear rpms-proc counters |
Clears statistics counters for AAA preauthentication requests, successes, and rejects. |
show rtpspi
To display Real-time Transport Protocol (RTP) serial peripheral interface (SPI) active call details and call statistics, use the show rtpspi command in privileged EXEC mode.
show rtpspi {call | statistics}
Syntax Description
call |
Displays RTP SPI active call details. |
statistics |
Displays RTP SPI call statistics information. |
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.4(22)T |
This command was introduced in a release earlier than Cisco IOS Release 12.4(22)T. |
Examples
The following is sample output from the show rtpspi statistics command:
Router# show rtpspi statistics
RTP Statistics info:
No. CallId Xmit-pkts Xmit-bytes Rcvd-pkts Rcvd-bytes Lost pkts Jitter Latenc
1 48 0x3BA 0x25440 0x17 0xD99 0x0 0x0 0x0
2 50 0x3BA 0x4A88 0x70 0x8AD 0x0 0x0 0x0
Table 151 describes the significant fields shown in the display.
Related Commands
|
|
|
|---|---|
debug rtpspi all |
Debugs all RTP SPI errors, sessions, and in/out functions. |
show rtsp client session
To display cumulative information about Real Time Streaming Protocol (RTSP) session records, use the show rtsp client session command in privileged EXEC mode.
show rtsp client session {history | active} [detailed]
Syntax Description
Command Default
Active (current) stream information is displayed.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
Use this command to display cumulative information about the session, packet statistics, and general call information such as call ID and session ID.
Note Session refers to a session between the application and the RTSP client. Each call leg that is configured to use RTSP streaming has a session.
A call leg could play several prompts in a session; the "Play Time" refers to the play time associated with a stream or, in other words, a prompt; the cumulative play time is the sum total of all streams (or prompts) played out in a session.
The command output is a stream block that contains information about the stream (URL, packet statistics, current state of the stream, play duration, call ID, session ID, individual RTSP stream URLs, and packet statistics).
Examples
The following is sample output from the show rtsp client session active command:
Router# show rtsp client session active
RTSP Session ID:0x8 Current Status:RTSP_STATUS_PLAYING
Associated CallID:0xF
Active Request:RTSP_API_REQ_PLAY
Control Protocol:TCP Data Protocol:RTP
Total Packets Transmitted:0 (0 bytes)
Total Packets Received:708 (226560 bytes)
Cumulative Elapsed Play Time:00:00:28.296
Cumulative Elapsed Record Time:00:00:00.000
Session ID:0x8 State:ACTIVE
Local IP Address:10.13.79.45 Local Port 16660
Server IP Address:10.13.79.6 Server Port 11046
Stream URL:rtsp://rtsp-cisco.cisco.com:554/chinna.au/streamid=0
Packets Transmitted:0 (0 bytes)
Packets Received:708 (226560 bytes)
Elapsed Play Time:00:00:28.296
Elapsed Record Time:00:00:00.000
ReceiveDelay:85 LostPackets:0
The following is sample output from the show rtsp client session history detailed command:
Router# show rtsp client session history detailed
RTSP Session ID:0x8
Associated CallID:0xF
Control Protocol:TCP Data Protocol:RTP
Total Packets Transmitted:0 (0 bytes)
Total Packets Received:2398 (767360 bytes)
Cumulative Elapsed Play Time:00:01:35.916
Cumulative Elapsed Record Time:00:00:00.000
Session ID:0x8 State:INACTIVE
Local IP Address:10.13.79.45 Local Port 16660
Server IP Address:10.13.79.6 Server Port 11046
Stream URL:rtsp://rtsp-cisco.cisco.com:554/chinna.au/streamid=0
Packets Transmitted:0 (0 bytes)
Packets Received:2398 (767360 bytes)
Play Time:00:01:35.916
Record Time:00:00:00.000
OntimeRcvPlayout:93650
GapFillWithSilence:0
GapFillWithPrediction:70
GapFillWithInterpolation:0
GapFillWithRedundancy:0
HighWaterPlayoutDelay:85
LoWaterPlayoutDelay:64
ReceiveDelay:85 LostPackets:0
EarlyPackets:2 LatePackets:12
Table 152 describes significant fields shown in this output.
Related Commands
show rudpv0 failures
To display SS7 Reliable User Datagram Protocol (RUDP) failure statistics, use the show rudpv0 failures command in privileged EXEC mode.
show rudpv0 failures
Syntax Description
This command has no keywords or arguments.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.0(7)XR |
This command was introduced. |
12.1(1)T |
This command was integrated into Cisco IOS Release 12.1(1)T. |
Examples
The following is sample output from this command showing displaying RUDP failures.
Router# show rudpv0 failures
**** RUDP Failure Stats ****
CreateBufHdrsFailure 0
CreateConnRecsFailure 0
CreateEventsFailure 0
NotReadyFailures 0
OptionNotSupportedFailures 0
OptionRequiredFailures 0
GetConnRecFailures 0
InvalidConnFailures 0
EventUnavailFailures 0
EmptyBufferSendFailures 0
BufferTooLargeFailures 0
ConnNotOpenFailures 0
SendWindowFullFailures 0
GetBufHdrSendFailures 0
GetDataBufFailures 0
GetBufHdrFailures 0
SendEackFailures 0
SendAckFailures 0
SendSynFailures 0
SendRstFailures 0
SendNullFailures 0
TimerNullFailures 0
FailedRetransmits 0
IncomingPktsDropped 0
UnknownRudpEvents 0
Field descriptions should be self-explanatory.
Related Commands
show rudpv0 statistics
To display SS7 Reliable User Datagram Protocol (RUDP) internal statistics, use the show rudpv0 statistics command in privileged EXEC command.
show rudpv0 statistics
Syntax Description
This command has no keywords or arguments.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.0(7)XR |
This command was introduced. |
12.1(1)T |
This command was integrated into Cisco IOS Release 12.1(1)T. |
Usage Guidelines
Because statistics counters are continually updated, the cumulative total may not be exactly equal to individual connection counters. After a connection is reset, previous statistics are lost, so the current connection statistics reflect only instances of the RUDP connection since the last reset.
Cumulative statistics reflect counts since the router was rebooted or since the clear rudpv0 statistics command was used.
Examples
The following is sample output from this command displaying RUDP statistics and states for two connections. The fields are self-explanatory.
Router# show rudpv0 statistics
*** RUDP Internal Stats ****
Connection ID: 811641AC, Current State: OPEN
RcvdInSeq 1
RcvdOutOfSeq 0
SoftResets 0
SoftResetsRcvd 0
TotalPacketsSent 4828
TotalPacketsReceived 4826
TotalDataBytesSent 0
TotalDataBytesReceived 4
TotalDataPacketsSent 0
TotalDataPacketsReceived 1
TotalPacketsRetrans 0
TotalPacketsDiscarded 0
Connection ID: 81163FD4, Current State: OPEN
RcvdInSeq 2265
RcvdOutOfSeq 0
SoftResets 0
SoftResetsRcvd 0
TotalPacketsSent 7863
TotalPacketsReceived 6755
TotalDataBytesSent 173690
TotalDataBytesReceived 56121
TotalDataPacketsSent 2695
TotalDataPacketsReceived 2265
TotalPacketsRetrans 0
TotalPacketsDiscarded 0
Cumulative RudpV0 Statistics
RcvdInSeq 2266
RcvdOutOfSeq 0
SoftResets 0
SoftResetsRcvd 0
TotalPacketsSent 12691
TotalPacketsReceived 11581
TotalDataBytesSent 173690
TotalDataBytesReceived 56125
TotalDataPacketsSent 2695
TotalDataPacketsReceived 2266
TotalPacketsRetrans 0
TotalPacketsDiscarded 0
Related Commands
show rudpv1
To display Reliable User Datagram Protocol (RUDP) information, use the show rudpv1 command in privileged EXEC mode.
show rudpv1 {failures | parameters | statistics}
Syntax Description
failures |
RUDP failure statistics. |
parameters |
RUDP connection parameters. |
statistics |
RUDP internal statistics. |
Command Modes
Privileged EXEC
Command History
Usage Guidelines
Because statistics counters are continually updated, the cumulative total may not be exactly equal to individual connection counters. After a connection is reset, previous statistics are lost, so the current connection statistics reflect only instances of the RUDP connection since the last reset.
Cumulative statistics reflect counts since the router was rebooted or since the clear rudpv1 statistics command was used.
Examples
The following is sample output from this command:
Router# show rudpv1 failures
**** RUDPV1 Failure Stats ****
CreateBufHdrsFailure 0
CreateConnRecsFailure 0
CreateEventQueueFailure 0
OsSpecificInitFailure 0
NotReadyFailures 0
OptionNotSupportedFailures 0
InvalidOptionFailures 0
OptionRequiredFailures 0
GetConnRecFailures 0
InvalidConnFailures 0
EventUnavailFailures 0
GetConnRecFailures 0
FindConnRecFailures 0
EmptyBufferSendFailures 0
BufferTooLargeFailures 0
ConnNotOpenFailures 0
SendWindowFullFailures 0
GetBufHdrSendFailures 0
SendInProgressFailures 0
GetDataBufFailures 0
GetBufHdrFailures 0
SendFailures 0
SendEackFailures 0
SendAckFailures 0
SendSynFailures 0
SendRstFailures 0
SendTcsFailures 0
SendNullFailures 0
TimerFailures 0
ApplQueueFailures 0
FailedRetransmits 0
IncomingPktsDropped 0
CksumErrors 0
UnknownRudpv1Events 0
InvalidVersion 0
InvalidNegotiation 0
The following is sample output from the show rudpv1 parameters command:
Router# show rudpv1 parameters
*** RUDPV1 Connection Parameters ***
Next Connection Id:61F72B6C, Remote conn id 126000
Conn State OPEN
Conn Type ACTIVE
Accept Negot params? Yes
Receive Window 32
Send Window 32
Receive Seg Size 384
Send Seg Size 384
Requested Negotiated
Max Auto Reset 5 5
Max Cum Ack 3 3
Max Retrans 2 2
Max OutOfSeq 3 3
Cum Ack Timeout 100 100
Retrans Timeout 300 300
Null Seg Timeout 1000 1000
Trans State Timeout 2000 2000
Cksum type Hdr Hdr
Next Connection Id:61F72DAC, Remote conn id 126218
Conn State OPEN
Conn Type ACTIVE
Accept Negot params? Yes
Receive Window 32
Send Window 32
Receive Seg Size 384
Send Seg Size 384
Requested Negotiated
Max Auto Reset 5 5
Max Cum Ack 3 3
Max Retrans 2 2
Max OutOfSeq 3 3
Cum Ack Timeout 100 100
Retrans Timeout 300 300
Null Seg Timeout 1000 1000
Trans State Timeout 2000 2000
Cksum type Hdr Hdr
The following is sample output from the show rudpv1 statistics command:
Router# show rudpv1 statistics
*** RUDPV1 Internal Stats ****
Connection ID:61F72B6C, Current State:OPEN
RcvdInSeq 647
RcvdOutOfSeq 95
AutoResets 0
AutoResetsRcvd 0
TotalPacketsSent 1011
TotalPacketsReceived 958
TotalDataBytesSent 17808
TotalDataBytesReceived 17808
TotalDataPacketsSent 742
TotalDataPacketsReceived 742
TotalPacketsRetrans 117
TotalPacketsDiscarded 38
Connection ID:61F72DAC, Current State:OPEN
RcvdInSeq 0
RcvdOutOfSeq 0
AutoResets 0
AutoResetsRcvd 0
TotalPacketsSent 75
TotalPacketsReceived 75
TotalDataBytesSent 0
TotalDataBytesReceived 0
TotalDataPacketsSent 0
TotalDataPacketsReceived 0
TotalPacketsRetrans 0
TotalPacketsDiscarded 0
Cumulative RudpV1 Statistics
NumCurConnections 2
RcvdInSeq 652
RcvdOutOfSeq 95
AutoResets 0
AutoResetsRcvd 0
TotalPacketsSent 1102
TotalPacketsReceived 1047
TotalDataBytesSent 18048
TotalDataBytesReceived 18048
TotalDataPacketsSent 752
TotalDataPacketsReceived 752
TotalPacketsRetrans 122
TotalPacketsDiscarded 38
Related Commands
|
|
|
|---|---|
clear rudpv1 statistics |
Clears the RUDP statistics counters. |
debug rudpv1 |
Displays debugging information for RUDP. |
show sccp
To display Skinny Client Control Protocol (SCCP) information such as administrative and operational status, use the show sccp command in user EXEC or privileged EXEC mode.
show sccp [all | ccm group [number] | connections [details | internal | rsvp | summary] | server | statistics | call-identifications | call-references]
Syntax Description
Command Modes
User EXEC
Privileged EXEC (#)
Command History
Usage Guidelines
The router on which you use the show sccp command must be equipped with one or more digital T1/E1 packet voice trunk network modules (NM-HDVs) or high-density voice (HDV) transcoding/conferencing DSP farms (NM-HDV-FARMs) to provide digital signal processor (DSP) resources.
Use the show sccp ccm group command to show detailed information about all groups assigned to the Cisco Unified CallManager. The optional group-number argument can be added to select details about a specific group.
Configure the show sccp server statistics command on the Cisco Unified Border Element, IP-to-IP Gateway, or Session Border Controller where no SCCP phone is registered, to show the statistical counts on the SCCP server. The counts display queuing errors and message drops on the transcoder alone when it is on the Cisco Unified Border Element, IP-to-IP Gateway, or Session Border Controller.
When the show sccp server statistics command is used on the Cisco Unified Manager Express (CME), it is recommended for use together with the clear sccp server statistics command.
Examples
In the following sample output, the gateway IP address can be an IPv4 or IPv6 address when it operates on an IPv4/IPv6 dual stack.
Router# show sccp
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0
IPv6 Address: 2001:DB8:C18:1::3
IPv4 Address: 10.4.34.100
Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 172.19.242.27, Port Number: 2000
Priority: N/A, Version: 5.0.1, Identifier: 4
Trustpoint: N/A
Call Manager: 2001:DB8:C18:1::100, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 1
Trustpoint: N/A
Table 153 describes the significant fields shown in the display.
The following is sample output from this command for IPv4 only. The field descriptions are self-explanatory.
Router# show sccp
SCCP Admin State: UP
Gateway IP Address: 10.10.10.11, Port Number: 0
Switchover Method: IMMEDIATE, Switchback Method: GUARD_TIMER
Switchback Guard Timer: 1200 sec, IP Precedence: 5
Max Supported MTP sessions: 100
Transcoding Oper State: ACTIVE - Cause Code: NONE
Active CallManager: 10.10.10.35, Port Number: 2000
TCP Link Status: CONNECTED
Conferencing Oper State: DOWN - Cause Code: DSPFARM_DOWN
Active CallManager: NONE
TCP Link Status: NOT_CONNECTED
CallManager: 10.10.10.37, Port Number: 2000
Priority: 3, Version: 3.1
CallManager: 10.10.10.35, Port Number: 2000
Priority: 2, Version: 3.0
The following sample shows statistical information for SCCP transcoding and conferencing applications.
Router# show sccp statistics
SCCP Transcoding Application Statistics:
TCP packets rx 548, tx 559
Unsupported pkts rx 3, Unrecognized pkts rx 0
Register tx 3, successful 3, rejected 0, failed 0
KeepAlive tx 543, successful 540, failed 2
OpenReceiveChannel rx 2, successful 2, failed 0
CloseReceiveChannel rx 0, successful 0, failed 0
StartMediaTransmission rx 2, successful 2, failed 0
StopMediaTransmission rx 0, successful 0, failed 0
MediaStreamingFailure rx 0
Switchover 1, Switchback 1
SCCP Conferencing Application Statistics:
TCP packets rx 0, tx 0
Unsupported pkts rx 0, Unrecognized pkts rx 0
Register tx 0, successful 0, rejected 0, failed 0
KeepAlive tx 0, successful 0, failed 0
OpenReceiveChannel rx 0, successful 0, failed 0
CloseReceiveChannel rx 0, successful 0, failed 0
StartMediaTransmission rx 0, successful 0, failed 0
StopMediaTransmission rx 0, successful 0, failed 0
MediaStreamingFailure rx 0
Switchover 0, Switchback 0
In the following example, the secure value of the stype field indicates that the conection is encrypted. The field descriptions are self-explanatory.
Router# show sccp connections
sess_id conn_id stype mode codec ripaddr rport sport
16777222 16777409 secure-xcode sendrecv g729b 10.3.56.120 16772 19534
16777222 16777393 secure-xcode sendrecv g711u 10.3.56.50 17030 18464
Total number of active session(s) 1, and connection(s) 2
The following example shows the remote IP addresses of active RTP sessions, each of which shows either an IPv4 or an IPv6 address.
Router# show sccp connections
sess_id conn_id stype mode codec sport rport ripaddr
16777219 16777245 conf sendrecv g711u 16516 27814 10.3.43.46
16777219 16777242 conf sendrecv g711u 17712 18028 10.3.43.2
16777219 16777232 conf sendrecv g711u 16890 19440 10.3.43.2
16777219 16777228 conf sendrecv g711u 19452 17464 10.3.43.2
16777220 16777229 xcode sendrecv g711u 17464 19452 10.3.43.2
16777220 16777227 xcode sendrecv g729b 19466 19434 2001:0DB8:C18:1:212:79FF:FED7:B254
16777221 16777233 mtp sendrecv g711u 19440 16890 10.3.43.2
16777221 16777231 mtp sendrecv g711u 17698 17426 2001:0DB8:C18:1:212:79FF:FED7:B254
16777223 16777243 mtp sendrecv g711u 18028 17712 10.3.43.2
16777223 16777241 mtp sendrecv g711u 16588 19446 2001:0DB8:C18:1:212:79FF:FED7:B254
The following is sample output for the two Cisco CallManager Groups assigned to the Cisco Unified CallManager: group 5 named "boston office" and group 988 named "atlanta office".
Router# show sccp ccm group
CCM Group Identifier: 5
Description: boston office
Binded Interface: NONE, IP Address: NONE
Registration Retries: 3, Registration Timeout: 10 sec
Keepalive Retries: 3, Keepalive Timeout: 30 sec
CCM Connect Retries: 3, CCM Connect Interval: 1200 sec
Switchover Method: GRACEFUL, Switchback Method: GRACEFUL_GUARD
Switchback Interval: 10 sec, Switchback Timeout: 7200 sec
Signaling DSCP value: default, Audio DSCP value: default
CCM Group Identifier: 988
Description: atlanta office
Binded Interface: NONE, IP Address: NONE
Associated CCM Id: 1, Priority in this CCM Group: 1
Associated Profile: 6, Registration Name: MTP123456789988
Associated Profile: 10, Registration Name: CFB123456789966
Registration Retries: 3, Registration Timeout: 10 sec
Keepalive Retries: 5, Keepalive Timeout: 30 sec
CCM Connect Retries: 3, CCM Connect Interval: 10 sec
Switchover Method: IMMEDIATE, Switchback Method: IMMEDIATE
Switchback Interval: 15 sec, Switchback Timeout: 0 sec
Signaling DSCP value: default, Audio DSCP value: default
Table 154 describes the significant fields shown in the display.
The following sample output displays the summary information for all SCCP call references:
Router# show sccp call-reference
session_id: 16805277 session_type: vcf , profile_id: 101,
call-reference: 25666614 , Name: , Number: 3004
Audio conn_id: 16777929 , str_passthr: 0
rtp-call-id: 21 , bridge-id: 15 , msp-call-id: 12
mode: sendrecv, sport: 25146, rport 16648, ripaddr: 10.22.82.205
codec: g711u , pkt-period: 20
call-reference: 25666611 , Name: , Number: 6628
Audio conn_id: 16777926 , str_passthr: 0
rtp-call-id: 19 , bridge-id: 13 , msp-call-id: 12
mode: sendrecv, sport: 28168, rport 2398 , ripaddr: 128.107.147.125
codec: g711u , pkt-period: 20
Video conn_id: 16777927 , conn_id_tx: 16777928 , str_passthr: 0
rtp-call-id: 20 , bridge-id: 14 , msp-call-id: 12
mode: sendrecv, sport: 22604, rport 2400 , ripaddr: 128.107.147.125
bit rate: 1100kbps, frame rate: 30fps , rtp pt_rx: 97, rtp pt_tx: 97
codec: h264, Profile: 0x40, level: 2.2, max mbps: 81 (x500 MB/s), max fs: 7 (x256 MBs)
call-reference: 25666608 , Name: , Number: 62783365
Audio conn_id: 16777923 , str_passthr: 0
rtp-call-id: 16 , bridge-id: 11 , msp-call-id: 12
mode: sendrecv, sport: 21490, rport 20590, ripaddr: 10.22.83.142
codec: g711u , pkt-period: 20
Video conn_id: 16777924 , conn_id_tx: 16777925 , str_passthr: 0
rtp-call-id: 17 , bridge-id: 12 , msp-call-id: 12
mode: sendrecv, sport: 23868, rport 29010, ripaddr: 10.22.83.142
bit rate: 960kbps, frame rate: 30fps , rtp pt_rx: 97, rtp pt_tx: 97
codec: h264, Profile: 0x40, level: 3.0, max mbps: 0 (x500 MB/s), max fs: 0 (x256 MBs)
call-reference: 25666602 , Name: , Number: 62783363
Audio conn_id: 16777916 , str_passthr: 0
rtp-call-id: 11 , bridge-id: 7 , msp-call-id: 12
mode: sendrecv, sport: 26940, rport 20672, ripaddr: 10.22.82.48
codec: g711u , pkt-period: 20
Video conn_id: 16777917 , conn_id_tx: 16777919 , str_passthr: 0
rtp-call-id: 13 , bridge-id: 8 , msp-call-id: 12
mode: sendrecv, sport: 16462, rport 20680, ripaddr: 10.22.82.48
bit rate: 960kbps, frame rate: 30fps , rtp pt_rx: 97, rtp pt_tx: 97
codec: h264, Profile: 0x40, level: 2.0, max mbps: 72 (x500 MB/s), max fs: 5 (x256 MBs)
Total number of active session(s) 1
Total of number of active session(s) 1
with total of number of call-reference(s) 4
with total of number of audio connection(s) 4
with total of number of video connection(s) 3
The following sample output displays summary information for all SCCP call identifications:
Router# show sccp call-identifications
sess_id callref conn_id conn_id_tx spid rtp_callid msp_callid bridge_id codec stype prof_id
16805277 25666614 16777929 0 0 21 12 15 g711u vcf 101
16805277 25666611 16777926 0 0 19 12 13 g711u vcf 101
16805277 25666611 16777927 16777928 0 20 12 14 h264 vcf 101
16805277 25666608 16777923 0 0 16 12 11 g711u vcf 101
16805277 25666608 16777924 16777925 0 17 12 12 h264 vcf 101
16805277 25666602 16777916 0 0 11 12 7 g711u vcf 101
16805277 25666602 16777917 16777919 0 13 12 8 h264 vcf 101
Total number of active session(s) 1
The following sample displays the output from show sccp:
Router# show sccp
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/1
IPv4 Address: 172.19.156.7
Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 1.4.211.39, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 1
Trustpoint: N/A
Call Manager: 128.107.151.39, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 100
Trustpoint: N/A
V_Conferencing Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 128.107.151.39, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 101
Reported Max Streams: 4, Reported Max OOS Streams: 0
Layout: default 1x1
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
Supported Codec: h264: QCIF, Frame Rate: 15fps, Bit Rate: 64-704 Kbps
Supported Codec: h264: QCIF, Frame Rate: 30fps, Bit Rate: 64-704 Kbps
Supported Codec: h264: CIF, Frame Rate: 15fps, Bit Rate: 64-704 Kbps
Supported Codec: h264: CIF, Frame Rate: 30fps, Bit Rate: 64-704 Kbps
Supported Codec: h264: 4CIF, Frame Rate: 30fps, Bit Rate: 1000-1000 Kbps
TLS : ENABLED
Related Commands
show sccp ccm group
To display the groups that are configured on a specific Cisco Unified CallManager, use the show sccp ccm group command in privileged EXEC mode.
show sccp ccm group [group-number]
Syntax Description
group-number |
(Optional) Number that identifies the Cisco CallManager group. Range is 1 to 65535. There is no default value. |
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.3(8)T |
This command was introduced. |
Usage Guidelines
Use the show sccp ccm group command to show detailed information about all groups assigned to the Cisco Unified CallManager. The optional group-number argument can be added to select details about a specific group.
Examples
The following is sample output for the two Cisco CallManager Groups assigned to the Cisco Unified CallManager: group 5 named "boston office" and group 988 named "atlanta office".
Router# show sccp ccm group
CCM Group Identifier: 5
Description: boston office
Binded Interface: NONE, IP Address: NONE
Registration Retries: 3, Registration Timeout: 10 sec
Keepalive Retries: 3, Keepalive Timeout: 30 sec
CCM Connect Retries: 3, CCM Connect Interval: 1200 sec
Switchover Method: GRACEFUL, Switchback Method: GRACEFUL_GUARD
Switchback Interval: 10 sec, Switchback Timeout: 7200 sec
Signaling DSCP value: default, Audio DSCP value: default
CCM Group Identifier: 988
Description: atlanta office
Binded Interface: NONE, IP Address: NONE
Associated CCM Id: 1, Priority in this CCM Group: 1
Associated Profile: 6, Registration Name: MTP123456789988
Associated Profile: 10, Registration Name: CFB123456789966
Registration Retries: 3, Registration Timeout: 10 sec
Keepalive Retries: 5, Keepalive Timeout: 30 sec
CCM Connect Retries: 3, CCM Connect Interval: 10 sec
Switchover Method: IMMEDIATE, Switchback Method: IMMEDIATE
Switchback Interval: 15 sec, Switchback Timeout: 0 sec
Signaling DSCP value: default, Audio DSCP value: default
Table 155 describes significant fields shown in this output.
Related Commands
show sccp connections details
To display Skinny Client Control Protocol (SCCP) connection details such as call-leg details, use the show sccp connections details command in privileged EXEC mode.
show sccp connections details
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.3(8)T |
This command was introduced. |
Examples
The following is sample output from this command:
Router# show sccp connections details
bridge-info(bid, cid) - Normal bridge information(Bridge id, Calleg id)
mmbridge-info(bid, cid) - Mixed mode bridge information(Bridge id, Calleg id)
sess_id conn_id call-id codec pkt-period type bridge-info(bid, cid) mmbridge-info(bid, cid)
16800395 - 15 N/A N/A transmsp All RTPSPI Callegs N/A
16800395 18425889 14 g711u 20 rtpspi (10,15) N/A
16800395 18425905 13 g711u 20 rtpspi (9,15) N/A
Total number of active session(s) 1, connection(s) 2, and callegs 3
Related Commands
show sccp connections internal
To display the internal Skinny Client Control Protocol (SCCP) details such as time-stamp values, use the show sccp connections internal command in privileged EXEC mode.
show sccp connections internal
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.3(8)T |
This command was introduced. |
Examples
The following is sample output from this command:
Router# show sccp connections internal
Total number of active session(s) 0, and connection(s) 0
Field descriptions should be self-explanatory.
Related Commands
show sccp connections rsvp
To display information about active Skinny Client Control Protocol (SCCP) connections that are using RSVP, use the show sccp connections rsvp command in privileged EXEC mode.
show sccp connections rsvp
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.4(6)T |
This command was introduced. |
Examples
The following is sample output from this command:
Router# show sccp connections rsvp
sess_id conn_id rsvp_id dir local ip :port remote ip :port
16777578 16778093 -210 SEND 192.168.21.1 :18486 192.168.20.1 :16454
16777578 16778093 -211 RECV 192.168.21.1 :18486 192.168.20.1 :16454
Total active sessions 1, connections 2, rsvp sessions 2
Table 156 describes the fields shown in the display.
Related Commands
show sccp connections summary
To display a summary of the number of sessions and connections based on the service type under the Skinny Client Control Protocol (SCCP) application, use the show sccp connections summary command in privileged EXEC mode.
show sccp connections summary
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.3(8)T |
This command was introduced. |
Examples
The following is sample output from this command:
Router# show sccp connections summary
SCCP Application Service(s) Statistics Summary:
Total Conferencing Sessions: 0, Connections: 0
Total Transcoding Sessions: 0, Connections: 0
Total MTP Sessions: 0, Connections: 0
Total SCCP Sessions: 0, Connections: 0
Table 157 describes significant fields shown in this output.
Related Commands
show sccp server statistics
To display the statistical counts on the Skinny Client Control Protocol (SCCP) server, use the show sccp server statistics command in privileged EXEC mode.
show sccp server statistics
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.4(15)XY |
This command was introduced. |
Usage Guidelines
Configure the show sccp server statistics command on the Cisco Unified Border Element, IP-to-IP Gateway, or Session Border Controller where no SCCP phone is registered, to show the statistical counts on the SCCP server. The counts display queuing errors and message drops on the transcoder alone when it is on the Cisco Unified Border Element, IP-to-IP Gateway, or Session Border Controller.
When the show sccp server statistics command is used on the Cisco Unified Manager Express (CME), it is recommended for use together with the clear sccp server statistics command.
Examples
The following example shows the SCCP statistical counts on the server:
Router# show sccp server statistics
Failure type Error count
------------------------ -----------
Send queue enqueue 2
Socket send 3
Msg discarded upon error 5
Field descriptions should be self-explanatory.
Related Commands
|
|
|
|---|---|
clear sccp server statistics |
Clears the counts displayed the under show sccp server statistics command. |
show sdspfarm
To display the status of the configured digital signal processor (DSP) farms and transcoding streams, use the show sdspfarm command in privileged EXEC mode.
show sdspfarm {units [name unit-name | register | summary | tag number | unregister] | sessions [active | callID number | states | statistics | streamID number | summary] | message statistics}
Syntax Description
Command Modes
Privileged EXEC (#)
Command History
Examples
The following example displays the configured and registered DSP farms:
Router# show sdspfarm units
mtp-1 Device:MTP123456782012 TCP socket:[-1] UNREGISTERED
actual_stream:0 max_stream 0 IP:0.0.0.0 0 Unknown 0 keepalive 0
mtp-2 Device:MTP000a8aeaca80 TCP socket:[5] REGISTERED
actual_stream:40 max_stream 40 IP:10.5.49.160 11001 MTP YOKO keepalive 12074
Supported codec:G711Ulaw
G711Alaw
G729
G729a
G729b
G729ab
max-mtps:2, max-streams:240, alloc-streams:40, act-streams:0
The following is sample output from the show sdspfarm sessions active command:
Router# show sdspfarm sessions active
Stream-ID:3 mtp:2 192.0.2.0 20174 Local:2000 START
usage:MoH (DN=3 , CH=1) FE=TRUE
codec:G729 duration:20 vad:0 peer Stream-ID:4
Stream-ID:4 mtp:2 192.0.2.0 17072 Local:2000 START
usage:MoH (DN=3 , CH=1) FE=FALSE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:3
The following is sample output from the show sdspfarm sessions callID command:
Router# show sdspfarm sessions callID 51M
Stream-ID:6, srcCall-ID:51, codec:G729AnnexA , dur:20ms, vad:0, dstCall-ID:52, confID:5, mtp:2^
Peer Stream-ID:5, srcCall-ID:52, codec:G711Ulaw64k , dur:20ms, vad:0, dstCall-ID:51, confID:5, mtp:2^
Router-2015# show sdspfarm sessions callid 52
Stream-ID:5, srcCall-ID:52, codec:G711Ulaw64k , dur:20ms, vad:0, dstCall-ID:51, confID:5, mtp:2
Peer Stream-ID:6, srcCall-ID:51, codec:G729AnnexA , dur:20ms, vad:0, dstCall-ID:52, confID:5, mtp:2
The following is sample output from the show sdspfarm sessions statistics command:
Router# show sdspfarm sessions statistics
Stream-ID:1 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:1014 in-pak:0 discard:0
Stream-ID:2 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:3 mtp:2 10.5.49.160 20174 Local:2000START MoH (DN=3 , CH=1) FE=TRUE
codec:G729 duration:20 vad:0 peer Stream-ID:4
recv-pak:0 xmit-pak:0 out-pak:4780 in-pak:0 discard:0
Stream-ID:4 mtp:2 10.5.49.160 17072 Local:2000START MoH (DN=3 , CH=1) FE=FALSE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:3
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:5 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:6 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:7 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:8 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:9 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:10 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:11 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:12 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:13 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:14 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:15 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:16 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:17 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:18 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:19 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:20 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:21 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:22 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:23 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:24 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:25 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:26 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:27 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:28 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:29 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:30 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:31 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:32 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:33 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:34 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:35 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:36 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:37 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:38 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:39 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
Stream-ID:40 mtp:2 0.0.0.0 0 Local:0IDLE
codec:G711Ulaw64k duration:20 vad:0 peer Stream-ID:0
recv-pak:0 xmit-pak:0 out-pak:0 in-pak:0 discard:0
The following is sample output from the show sdspfarm sessions summary command:
Router# show sdspfarm sessions summary
max-mtps:2, max-streams:240, alloc-streams:40, act-streams:2
ID MTP State CallID confID Usage Codec/Duration
==== ===== ====== =========== ====== ============================= ==============
1 2 IDLE -1 0 G711Ulaw64k /20ms
2 2 IDLE -1 0 G711Ulaw64k /20ms
3 2 START -1 3 MoH (DN=3 , CH=1) FE=TRUE G729 /20ms
4 2 START -1 3 MoH (DN=3 , CH=1) FE=FALSE G711Ulaw64k /20ms
5 2 IDLE -1 0 G711Ulaw64k /20ms
6 2 IDLE -1 0 G711Ulaw64k /20ms
7 2 IDLE -1 0 G711Ulaw64k /20ms
8 2 IDLE -1 0 G711Ulaw64k /20ms
9 2 IDLE -1 0 G711Ulaw64k /20ms
10 2 IDLE -1 0 G711Ulaw64k /20ms
11 2 IDLE -1 0 G711Ulaw64k /20ms
12 2 IDLE -1 0 G711Ulaw64k /20ms
13 2 IDLE -1 0 G711Ulaw64k /20ms
14 2 IDLE -1 0 G711Ulaw64k /20ms
15 2 IDLE -1 0 G711Ulaw64k /20ms
16 2 IDLE -1 0 G711Ulaw64k /20ms
17 2 IDLE -1 0 G711Ulaw64k /20ms
18 2 IDLE -1 0 G711Ulaw64k /20ms
19 2 IDLE -1 0 G711Ulaw64k /20ms
20 2 IDLE -1 0 G711Ulaw64k /20ms
21 2 IDLE -1 0 G711Ulaw64k /20ms
22 2 IDLE -1 0 G711Ulaw64k /20ms
23 2 IDLE -1 0 G711Ulaw64k /20ms
24 2 IDLE -1 0 G711Ulaw64k /20ms
25 2 IDLE -1 0 G711Ulaw64k /20ms
26 2 IDLE -1 0 G711Ulaw64k /20ms
27 2 IDLE -1 0 G711Ulaw64k /20ms
28 2 IDLE -1 0 G711Ulaw64k /20ms
29 2 IDLE -1 0 G711Ulaw64k /20ms
30 2 IDLE -1 0 G711Ulaw64k /20ms
31 2 IDLE -1 0 G711Ulaw64k /20ms
32 2 IDLE -1 0 G711Ulaw64k /20ms
33 2 IDLE -1 0 G711Ulaw64k /20ms
34 2 IDLE -1 0 G711Ulaw64k /20ms
35 2 IDLE -1 0 G711Ulaw64k /20ms
36 2 IDLE -1 0 G711Ulaw64k /20ms
37 2 IDLE -1 0 G711Ulaw64k /20ms
38 2 IDLE -1 0 G711Ulaw64k /20ms
39 2 IDLE -1 0 G711Ulaw64k /20ms
40 2 IDLE -1 0 G711Ulaw64k /20ms
Table 158 describes the fields shown in the show sdspfarm command display.
Related Commands
show settlement
To display the configuration for all settlement servers and see specific provider and transactions, use the show settlement command in privileged EXEC mode.
show settlement [provider-number [transactions]]
Syntax Description
provider-number |
(Optional) Displays the attributes of a specific provider. |
transactions |
(Optional) Displays the transaction status of a specific provider. |
Defaults
Information about all servers is displayed.
Command Modes
Privileged EXEC
Command History
|
|
|
|---|---|
12.0(4)XH1 |
This command was introduced on the Cisco 2600 series, Cisco 3600 series, and Cisco AS5300. |
12.1(1)T |
This command was integrated into Cisco IOS Release 12.1(1)T. |
Examples
The following is sample output from this command displaying information about all settlement servers that are configured:
Router# show settlement
Settlement Provider 0
Type = osp
Address url = https://1.14.115.100:6556/
Encryption = all (default)
Max Concurrent Connections = 20 (default)
Connection Timeout = 3600 (s) (default)
Response Timeout = 1 (s) (default)
Retry Delay = 2 (s) (default)
Retry Limit = 1 (default)
Session Timeout = 86400 (s) (default)
Customer Id = 1000
Device Id = 1000
Roaming = Disabled (default)
Signed Token = on
Number of Connections = 0
Number of Transactions = 7
The following is sample output from this command displaying transaction and state information about a specific settlement server:
Router# show settlement 0 transactions
Transaction ID=8796304133625270342
state=OSPC_GET_DEST_SUCCESS, index=0
callingNumber=5710868, calledNumber=15125551212
Table 159 describes significant fields shown in this output. Provider attributes that are not configured are not shown.
.
Related Commands
show sgcp connection
To display all active Simple Gateway Control Protocol (SGCP) connections on a router, use the show sgcp connection command in EXEC mode.
show sgcp connection [interface number]
Syntax Description
interface |
(Optional) Displays output for a particular DS1 interface. |
number |
(Optional) Interface (controller) number. |
Defaults
All active SGCP connections on the host are displayed.
Command Modes
EXEC
Command History
Examples
The following is sample output from this command displaying active connections on a router:
Router# show sgcp connection
Endpoint Call_ID(C) Conn_ID(I) (P)ort (M)ode (S)tate (E)vent[SIFL] (R)esult[EA]
1. ds1-0/1@r3810-5 C=1,1,2 I=0x1 P=16492,16476 M=3 S=4 E=3,0,0,3 R=0, 0
The following is sample output from this command displaying the state of SGCP on a router:
Router# show sgcp connection
SGCP Admin State DOWN, Oper State DOWN
SGCP call-agent: 209.165.200.225 , SGCP graceful-shutdown enabled? FALSE
SGCP request timeout 40, SGCP request retries 10
Table 160 describes significant fields shown in this output.
Related Commands
|
|
|
show sgcp endpoint |
Displays SGCP endpoint information. |
show sgcp statistics |
Displays global statistics for the SGCP packet count, success, and failure counts. |
show sgcp endpoint
To display Simple Gateway Control Protocol (SGCP) endpoints that are eligible for SGCP management, use the show sgcp endpoint command in EXEC mode.
show sgcp endpoint [interface ds1 [ds0]]
Syntax Description
Command Modes
EXEC
Command History
Usage Guidelines
Use this command to display SGCP endpoint information for the whole router or for a specific DS1 interface and, optionally, a specific DS0. If you enter a nonexistent combination of a DS1 and DS0, the following error message appears: "No matching connection found."
Examples
The following is sample output from this command displaying SGCP endpoint information being set for a matching connection between DS1 interface 1 and DS0 interface 10:
Router# show sgcp endpoint interface 1 10
Related Commands
show sgcp statistics
To display global statistics for the Simple Gateway Control Protocol (SGCP) packet count, success and failure counts, and other information, use the show sgcp statistics command in EXEC mode.
show sgcp statistics
Syntax Description
This command has no arguments or keywords.
Command Modes
EXEC
Command History
Usage Guidelines
You can filter the displayed output, as shown in the examples.
Examples
The following is sample output from this command displaying SGCP packet statistics:
Router# show sgcp statistics
UDP pkts rx 5, tx 13
Unrecognized rx pkts 0, SGCP message parsing errors 0
Duplicate SGCP ack tx 0
Failed to send SGCP messages 0
CreateConn rx 1, successful 1, failed 0
DeleteConn rx 0, successful 0, failed 0
ModifyConn rx 0, successful 0, failed 0
DeleteConn tx 0, successful 0, failed 0
NotifyRequest rx 3, successful 3, failed 0
Notify tx 3, successful 3, failed 0
ACK tx 4, NACK tx 0
ACK rx 1, NACK rx 0
IP address based Call Agents statistics:
IP address 1.4.63.100, Total msg rx 5,
successful 5, failed 2
The following is sample output from this command showing how to filter output for specific information:
Router# show sgcp statistics | begin Failed
Failed to send SGCP messages 0
CreateConn rx 0, successful 0, failed 0
DeleteConn rx 0, successful 0, failed 0
ModifyConn rx 0, successful 0, failed 0
DeleteConn tx 0, successful 0, failed 0
NotifyRequest rx 0, successful 0, failed 0
Notify tx 0, successful 0, failed 0
ACK tx 0, NACK tx 0
ACK rx 0, NACK rx 0
Router# show sgcp statistics | exclude ACK
UDP pkts rx 0, tx 0
Unrecognized rx pkts 0, SGCP message parsing errors 0
Duplicate SGCP ack tx 0
Failed to send SGCP messages 0
CreateConn rx 0, successful 0, failed 0
DeleteConn rx 0, successful 0, failed 0
ModifyConn rx 0, successful 0, failed 0
DeleteConn tx 0, successful 0, failed 0
NotifyRequest rx 0, successful 0, failed 0
Notify tx 0, successful 0, failed 0
Router# show sgcp statistics | include ACK
ACK tx 0, NACK tx 0
ACK rx 0, NACK rx 0
Related Commands
|
|
|
show sgcp connection |
Displays all the active connections on the host Cisco AS5300 universal access server. |
show sgcp endpoint |
Displays SGCP endpoint information. |
show shared-line
To display information about the Session Initiation Protocol (SIP) shared lines, use the show shared-line command in user EXEC or privileged EXEC mode.
show shared-line {call | details | subscription | summary}
Syntax Description
Command Modes
User EXEC (>)
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.4(24)T |
This command was introduced. |
Examples
The following is sample output from the show shared-line call command:
Router# show shared-line call
Shared-Line active call info:
Shared-Line: '20141', active calls: 3
Local User Local Address Remote User Remote Address CallID
========== ===================== =========== ===================== ====
20141 20141@10.6.0.2 20143 20143@10.10.0.1 3168
20141 20141@10.6.0.1 Barge 20143@10.10.0.1 3209
20141 20141@10.6.0.2 20141 20141@10.10.0.1 3210
The following is sample output from the show shared-line details command:
Router# show shared-line details
Shared-Line info details:
Shared-Line: '20141', subscribed users: 2, max calls limit: 10
Index Users sub_id peer_tag Status
===== ===== ====== ======== ======
1 20141@10.6.0.1 5 40001 ACTIVE
2 20141@10.6.0.2 6 40002 ACTIVE
Free call queue size: 7, Active call queue size: 3
Message queue size: 20, Event queue size: 64
The following is sample output from the show shared-line subscription command:
Router# show shared-line subscription
Shared-Line Subscription Info:
Subscriptions to: '20141', total subscriptions: 2
SubID Subscriber Expires Sub-Status
===== ========== ======= ==========
5 20141@10.6.0.1 3600 NOTIFY_ACKED
6 20141@10.6.0.2 3600 NOTIFY_ACKED
The following is sample output from the show shared-line summary command:
Router# show shared-line summary
Shared-Line info summary:
Shared-Line: '20141', subscribed users: 2, max calls limit: 10
Table 161 describes the significant fields shown in the displays.
Related Commands
|
|
|
|---|---|
debug shared-line |
Displays debugging information about SIP shared lines. |
show sip dhcp
To display the Session Initiation Protocol (SIP) parameters retrieved via the Dynamic Host Configuration Protocol (DHCP), use the show sip dhcp command in privileged EXEC mode.
show sip dhcp
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.4(22)YB |
This command was introduced. |
15.0(1)M |
This command was integrated in Cisco IOS Release 15.0(1)M. |
Usage Guidelines
If SIP parameters are configured to be retrieved via DHCP, use the show sip dhcp command to display the SIP parameters retrieved.
Examples
The following is sample output from the show sip dhcp command:
Router# show sip dhcp
SIP UAC DHCP Info
SIP-DHCP interface: GigabitEthernet0/0
SIP server address: ipv4:9.13.2.36
Pilot number: 777777
Domain name: dns:cisco.com
Secondary number: 222222
Secondary number: 333333
Secondary number: 444444
Secondary number: 555555
Secondary number: 666666
Table 162 describes the significant fields shown in the display.
Related Commands
|
|
|
|---|---|
debug ccsip dhcp |
Displays information on SIP and DHCP interaction for debugging DHCP provisioning of SIP parameters. |
Feedback