Configuring Cisco DCNM-SAN Server
This chapter describes Cisco DCNM-SAN Server, which is a platform for advanced MDS monitoring, troubleshooting, and configuration capabilities. No additional software needs to be installed. The server capabilities are an integral part of the Cisco DCNM-SAN software.
This chapter contains the following sections:
Information About Cisco DCNM-SAN Server
Install Cisco DCNM-SAN Server on a computer that you want to provide centralized MDS management services and performance monitoring. SNMP operations are used to efficiently collect fabric information. The Cisco DCNM-SAN software, including the server components, requires about 60 MB of hard disk space on your workstation. Cisco DCNM-SAN Server runs on Windows 2000, Windows 2003, Windows XP, Solaris 9 and 10, and Red Hat Enterprise Linux AS Release 5.
Each computer configured as a Cisco DCNM-SAN Server can monitor multiple Fibre Channel SAN fabrics. Up to 16 clients (by default) can connect to a single Cisco DCNM-SAN Server concurrently. The Cisco DCNM-SAN Clients can also connect directly to an MDS switch in fabrics that are not monitored by a Cisco DCNM-SAN Server, which ensures you can manage any of your MDS devices from a single console.
DCNM-SAN Server Features
Cisco DCNM-SAN Server has the following features:
- Multiple fabric management — DCNM-SAN Server monitors multiple physical fabrics under the same user interface. This facilitates managing redundant fabrics. A licensed DCNM-SAN Server maintains up-to-date discovery information on all configured fabrics so device status and interconnections are immediately available when you open the DCNM-SAN Client.
- Continuous health monitoring— MDS health is monitored continuously, so any events that occurred since the last time you opened the DCNM-SAN Client are captured.
- Roaming user profiles —The licensed DCNM-SAN Server uses the roaming user profile feature to store your preferences and topology map layouts on the server, so that your user interface will be consistent regardless of what computer you use to manage your storage networks.
![]() Note |
You must have the same release of Cisco DCNM-SAN Client and Cisco DCNM-SAN Server. |
![]() Note |
You will not be able to manage a SAN fabric if the DCNM-SAN Server is going through a IP NAT firewall to access the SAN fabric. All the IP addresses that are discovered in a SAN fabric must be directly reachable by the DCNM-SAN Server. |
Licensing Requirements For Cisco DCNM-SAN Server
When you install DCNM-SAN, the basic unlicensed version of Cisco DCNM-SAN Server is installed with it. To get the licensed features, such as Performance Manager, remote client support, and continuously monitored fabrics, you need to buy and install the Cisco DCNM-SAN Server package.
However, trial versions of these licensed features are available. To enable the trial version of a feature, you run the feature as you would if you had purchased the license. You see a dialog box explaining that this is a demo version of the feature and that it is enabled for a limited time.
Installing and Configuring Cisco DCNM-SAN Server
Before you begin
Procedure
Step 1 |
Install Cisco DCNM-SAN Client and Cisco DCNM-SAN Server on your workstation. See the Installing Cisco DCNM-SAN Server. |
Step 2 |
Log in to DCNM-SAN. |
Step 3 |
Set Cisco DCNM-SAN Server to continuously monitor the fabric. See the Managing a Cisco DCNM-SAN Server Fabric. |
Step 4 |
Repeat Step 2 through Step 3 for each fabric that you want to manage through Cisco DCNM-SAN Server. |
Step 5 |
Install DCNM-SAN Web Server. See the Verifying Performance Manager Collections. |
Step 6 |
Verify Performance Manager is collecting data. See the Verifying Performance Manager Collections. |
Installing Cisco DCNM-SAN Server
When you install DCNM-SAN, the basic version of the Cisco DCNM-SAN Server (unlicensed) is installed with it. After you click the DCNM-SAN icon, a dialog box opens and you can enter the IP address of a computer running the Cisco DCNM-SAN Server component. If you do not see the Cisco DCNM-SAN Server IP address text box, click Options to expand the list of configuration options. If the server component is running on your local machine, leave localhost in that field. If you try to run DCNM-SAN without specifying a valid server, you are prompted to start the Cisco DCNM-SAN Server locally.
On a Windows PC, you install the Cisco DCNM-SAN Server as a service. This service can then be administered using Services in the Administrative Tools. The default setting for the Cisco DCNM-SAN Server service is that the server is automatically started when the Windows PC is rebooted. You can change this behavior by modifying the properties in Services.
For switches running Cisco MDS 9000 FabricWare, you must install DCNM-SAN from the CD-ROM included with your switch, or you can download DCNM-SAN from Cisco.com.
![]() Note |
You can have only one instance of Cisco DCNM-SAN Server running on a computer. If you have a DCNM-SAN Standalone version on your computer, you may need to uninstall it before you install Cisco DCNM-SAN Server. |
To download the software from Cisco.com, go to the following website:
http://cisco.com/cgi-bin/tablebuild.pl/mds-fm
![]() Note |
If you are upgrading from an earlier version to 5.0(1a) or later, that is configured with HTTPS to use your own self-provisioned or a third-party issued SSL certificate, make sure that you set the keystore password and then restart the DCNM-SAN Server. To set the keystore password, run $INSTALLDIR/dcm/fm/bin encrypter.bat ssl. |
Procedure
Step 1 |
Click the Install Management Software link. |
||||
Step 2 |
Choose Management Software > Cisco DCNM-SAN . |
||||
Step 3 |
Click the Installing DCNM-SAN link. |
||||
Step 4 |
Click the FM Installer link. You see the welcome message in the Cisco DCNM-SAN Installer window. |
||||
Step 5 |
Click the Custom radio button, and then click Next to begin installation. |
||||
Step 6 |
Check the I accept the terms of the License Agreement check box, and then click Next . You see the Install Options dialog box. |
||||
Step 7 |
Click the Cisco DCNM-SAN Server (Licensed) radio button to install the server components for Cisco DCNM-SAN Server. |
||||
Step 8 |
Click Add server to an existing server federation to add the server to a federation.
Example:
|
||||
Step 9 |
Select an installation folder on your workstation for Cisco DCNM-SAN. On Windows, the default location is C:\Program Files\Cisco Systems. |
||||
Step 10 |
Click Next . You see the Database Options dialog box. |
||||
Step 11 |
Click the radio button for either Install PostgreSQL or Use existing DB to specify which database you want to use. If you choose Install PostgreSQL, accept the defaults and enter a password. The PostgreSQL database will be installed.
|
||||
Step 12 |
If you select Use existing DB, click the radio button for either PostgreSQL 8.1/8.2 or Oracle10g. |
||||
Step 13 |
Click Next in the Database Options dialog box. You see the Configuration Options dialog box. |
||||
Step 14 |
Click Install to install Cisco DCNM-SAN Server. |
What to do next
If you are evaluating one of these Cisco DCNM-SAN Server features and want to stop the evaluation period for that feature, you can do that using Device Manager.
Data Migration in Cisco DCNM-SAN Server
The database migration should be limited to the existing database. Data collision can occur when you merge the data between the several databases.
When you upgrade a non federation mode database to a federation mode database for the first time, the cluster sequence table is filled with the values larger than the corresponding ones in the sequence table and conforming to the cluster sequence number format for that server ID.
Verifying Performance Manager Collections
Once Performance Manager collections have been running for five or more minutes, you can verify that the collections are gathering data by choosing Performance Manager > Reports in DCNM-SAN. You see the first few data points gathered in the graphs and tables.
Managing a Cisco DCNM-SAN Server Fabric
You can continuously manage a Cisco DCNM-SAN Server fabric, whether or not a client has that fabric open. A continuously managed fabric is automatically reloaded and managed by Cisco DCNM-SAN Server whenever the server starts.
Selecting a Fabric to Manage Continuously
Procedure
Step 1 |
Choose Server > Admin . You see the Control Panel dialog box with the Fabrics tab open.
|
||||
Step 2 |
Choose one of the following Admin options:
|
||||
Step 3 |
Click Apply . |
What to do next
![]() Note |
If you are collecting data on these fabrics using Performance Manager, you should now configure flows and define the data collections. |
Cisco DCNM-SAN Server Properties File
The Cisco DCNM-SAN Server properties file (MDS 9000\server.properties ) contains a list of properties that determine how the Cisco DCNM-SAN Server will function. You can edit this file with a text editor, or you can set the properties through the DCNM-SAN Web Services GUI, under the Admin tab.
![]() Note |
As of Cisco NX-OS Release 4.1(1b) and later, you can optionally encrypt the password in the server.properties and the AAA.properties files. |
The server properties file contains these nine general sections:
- GENERAL : Contains the general settings for the server.
- SNMP SPECIFIC : Contains the settings for SNMP requests, responses, and traps.
- SNMP PROXY SERVER SPECIFIC : Contains the settings for SNMP proxy server configuration and TCP port designation.
- GLOBAL FABRIC : Contains the settings for fabrics, such as discovery and loading.
- CLIENT SESSION : Contains the settings for DCNM-SAN Clients that can log into the server.
- EVENTS : Contains the settings for syslog messages.
- PERFORMANCE CHART: Contains the settings for defining the end time to generate a Performance Manager chart.
- EMC CALL HOME: Contains the settings for the forwarding of traps as XML data using e-mail, according to EMC specifications.
- EVENT FORWARD SETUP: Contains the settings for forwarding events logged by Cisco DCNM-SAN Server through e-mail.
The following server properties are added or changed in the Cisco DCNM-SAN Release 3.x and later.
SNMP Specific
- snmp.preferTCP : If this option is set to true, TCP is the default protocol for Cisco DCNM-SAN Server to communicate with switches. By default, this setting is true . For those switches that do not have TCP enabled, Cisco DCNM-SAN Server uses UDP. The advantage of this setting is the ability to designate one TCP session for each SNMP user on a switch. It also helps to reduce timeouts and increase scalability.
![]() Note |
If you set this option to false, the same choice must be set in DCNM-SAN. The default value of snmp.preferTCP for DCNM-SAN is true. |
Performance Chart
- pmchart.currenttime : Specifies the end time to generate a Performance Manager chart. This should only be used for debugging purposes.
EMC Call Home
- server.callhome.enable : Enables or disables EMC Call Home. By default, it is disabled.
- server.callhome.location : Specifies the Location parameter.
- server.callhome.fromEmail : Specifies the From Email list.
- server.callhome.recipientEmail : Specifies the recipientEmail list.
- server.callhome.smtphost : Specifies the SMTP host address for outbound e-mail.
- server.callhome.xmlDir : Specifies the path to store the XML message files.
- server.callhome.connectType : Specifies the method to use to remotely connect to the server.
- server.callhome.accessType : Specifies the method to use to establish remote communication with the server.
- server.callhome.version : Specifies the version number of the connection type.
- server.callhome.routerIp : Specifies the public IP address of the RSC router.
Event Forwarding
- server.forward.event.enable : Enables or disables event forwarding.
- server.forward.email.fromAddress : Specifies the From Email list.
- server.forward.email.mailCC : Specifies the CC Email list.
- server.forward.email.mailBCC: Specifies the BCC Email list.
- server.forward.email.smtphost : Specifies the SMTP host address for outbound e-mail.
Deactivation
- deactivate.confirm=deactivate : Specific Request for User to type a String for deactivation.
![]() Note |
In a federated server environment, you should not change Cisco DCNM-SAN Server properties by modifying server.properties file. You must modify the server.properties using web client menu Admin > Configure > Preferences. |
Modifying Cisco DCNM-SAN Server
Fabric Manager Release 2.1(2) or later allows you to modify certain Cisco DCNM-SAN Server settings without stopping and starting the server.
Adding Cisco DCNM-SAN Server Users
Before you begin
You must be a network administrator before you can manage users.
To add a Cisco DCNM-SAN Server user or to change the password for an existing user using DCNM-SAN, follow these steps:
Procedure
Step 1 |
Click the Local FM Users tab in the Control Panel dialog box. You see a list of DCNM-SAN users. |
Step 2 |
Click New to add a user or click the user name and click Edit to change the password for an existing user. You see the FM User dialog box. |
Step 3 |
Set the username and password for the new user and then click Apply . |
Removing Cisco DCNM-SAN Server Users
To remove a Cisco DCNM-SAN Server user using DCNM-SAN, follow these steps:
Before you begin
You must be a network administrator before you can manage users.
Procedure
Step 1 |
Click the Local FM Users tab in the Control Panel dialog box. You see a list of DCNM-SAN users. |
Step 2 |
Click the username you want to delete. |
Step 3 |
Click Remove to delete the user. |
Step 4 |
Click Yes to confirm the deletion or No to cancel it. |
Changing the Cisco DCNM-SAN Server Username and Password
You can modify the username or password used to access a fabric from DCNM-SAN Client without restarting Cisco DCNM-SAN Server.
Procedure
Step 1 |
Choose Server > Admin. You see the Control Panel dialog box with the Fabrics tab open. |
Step 2 |
Set the Name or Password for each fabric that you are monitoring with Cisco DCNM-SAN Server. |
Step 3 |
Click Apply to save these changes. |
Changing the DCNM-SAN Server Fabric Discovery Username and Password
Procedure
Step 1 |
Click Server > Admin in Cisco DCNM-SAN. You see the Control Panel dialog box with the Fabrics tab open. |
Step 2 |
Click the fabrics that have updated user name and password information. |
Step 3 |
From the Admin listbox, select Unmanage and then click Apply. |
Step 4 |
Enter the appropriate user name and password and then click Apply. For more information, see the Performance Manager Authentication. |
Changing the Polling Period and Fabric Rediscovery Time
Cisco DCNM-SAN Server periodically polls the monitored fabrics and periodically rediscovers the full fabric at a default interval of five cycles. You can modify these settings from DCNM-SAN Client without restarting Cisco DCNM-SAN Server.
Procedure
Step 1 |
Choose Server > Admin. You see the Control Panel dialog box with the Fabrics tab open. |
Step 2 |
For each fabric that you are monitoring with Cisco DCNM-SAN Server, set the Polling Interval to determine how frequently Cisco DCNM-SAN Server polls the fabric elements for status and statistics. |
Step 3 |
For each fabric that you are monitoring with Cisco DCNM-SAN Server, set the Rediscover Cycles to determine how often Cisco DCNM-SAN Server rediscovers the full fabric. |
Step 4 |
Click Apply to save these changes. |
Changing the IP Address of the Cisco DCNM-SAN Server
Procedure
Step 1 |
Stop the Cisco DCNM-SAN Server. |
||
Step 2 |
For releases prior to DCNM release 11.5, change the following parameter in the $INSTALLDIR/conf/FMServer.conf.
For example:
|
||
Step 3 |
Change the following parameter in the $INSTALLDIR/conf/server.properties.
For example:
|
||
Step 4 |
Enter the following command to assign a new IP address.
Assume $INSTALLDIR is the top directory of DCNM-SAN installation. The above command is for single server instance, where 0 is the server ID. For example:
|
Using Device Aliases or FC Aliases
You can change whether DCNM-SAN uses FC aliases or global device aliases from DCNM-SAN Client without restarting Cisco DCNM-SAN Server.
Procedure
Step 1 |
Choose Server > Admin. You see the Control Panel dialog box with the Fabrics tab open. |
Step 2 |
For each fabric that you are monitoring with Cisco DCNM-SAN Server, check the Device Alias check box to use global device aliases, or uncheck to use FC aliases. |
Step 3 |
Click Apply to save these changes. |
Server Federation
Server Federation is a distributed system that includes a collection of intercommunicated servers or computers that is utilized as a single, unified computing resource. With Cisco DCNM-SAN Server Federation, you can communicate with multiple servers together in order to provide scalability and easy manageability of data and programs running within the federation. The core of server federation includes several functional units such as Cisco DCNM-SAN Server, embedded web servers, database and DCNM-SAN Client that accesses the servers.
The Cisco DCNM-SAN Server in the federation uses the same database to store and retrieve data. The database is shared among different servers to share common information. A DCNM-SAN Client or DCNM-SAN Web Client can open fabrics from the Cisco DCNM-SAN Server using the mapping table. A fabric can be moved from one logical server to another. A logical server also can be moved from one physical machine to another machine.
Restrictions
- You cannot upgrade more than one Cisco DCNM-SAN Server in an existing federation. If you choose to do so, you may not be able to migrate the Performance Manager statistics and other information on that server.
- You may require to synchronize the time on all the DCNM-SAN Servers in a federated server environment.
Mapping Fabric ID to Server ID
The IP address of the physical server will be mapped to the server ID during the installation of the Cisco DCNM-SAN Server whenever the IP address of the physical server is changed, you need to map the IP address to the server ID using the PLMapping script provided with the Cisco DCNM-SAN Server. Whenever the you open or discover a fabric, the fabric ID will be mapped to the server ID . You can move a fabric to a different server ID using the control panel.
Procedure
Step 1 |
Choose Server > Admin. You see the Control Panel. |
Step 2 |
Select the fabric that you want to move to a different server and then click Move. You see the Move Fabric dialog box. |
Step 3 |
You see the fabrics that you selected in the Fabrics to Move list box. From the Move To Server drop-down list select the server you want to move the fabric to. |
Step 4 |
Click Move. |
Opening the Fabric on a Different Server
Procedure
Step 1 |
Choose Server > Admin. You see the Control Panel. |
||
Step 2 |
Click Discover. You see the Discover New Fabric dialog box. |
||
Step 3 |
In the Seed Switch list box, enter the IP Address of the seed switch. |
||
Step 4 |
In the User Name field, enter the username. |
||
Step 5 |
In the password field, enter the password. |
||
Step 6 |
From the Auth-Privacy drop-down list, choose the privacy protocol you want to apply. |
||
Step 7 |
To open the selected fabric in a different server, select the server ID from the Server drop-down list. |
||
Step 8 |
Click Discover.
|
Viewing the Sessions in a Federation
Procedure
Step 1 |
Choose Server > Admin. |
Step 2 |
Click the Connected Clients tab. You see the Control Panel. |
Additional References
- Server Federation is a licensed feature. For more information on Cisco DCNM-SAN Server Licensing, see Cisco MDS 9000 Family NX-OS Licensing Guide.
- For more information on deploying Cisco DCNM-SAN Server in a federation, see Cisco Fabric Manager Server Federation Deployment Guide.