Configuring FICON
Fibre Connection (FICON) interface capabilities enhance the Cisco MDS 9000 Family by supporting both open systems and mainframe storage network environments. The control unit port (CUP) also is supported, which allows in-band management of the switch from FICON processors.
![]() Note |
Cisco Fabric Manager release 3.x does not support FICON management of Cisco MDS 9000 Family switches running SAN-OS release 2.(x). |
Information About FICON
The Cisco MDS 9000 Family supports the Fibre Channel Protocol (FCP), FICON, iSCSI, and FCIP capabilities within a single, high-availability platform (see Figure 1).
The FICON feature is not supported on:
-
Cisco MDS 9120 switches
-
Cisco MDS 9124 switches
-
Cisco MDS 9140 switches
-
The 32-port Fibre Channel switching module
-
Cisco Fabric Switch for HP c-Class BladeSystem
-
Cisco Fabric Switch for IBM BladeSystem
FCP and FICON are different FC4 protocols and their traffic is independent of each other. Devices using these protocols should be isolated using VSANs.
The fabric binding feature helps prevent unauthorized switches from joining the fabric or disrupting current fabric operations (refer to the Cisco MDS 9000 Family NX-OS Security Configuration Guide ). The Registered Link Incident Report (RLIR) application provides a method for a switch port to send an LIR to a registered Nx port.
![](/c/dam/en/us/td/i/100001-200000/100001-110000/105001-106000/105211.ps/_jcr_content/renditions/105211.jpg)
This section includes the following topics:
FICON Requirements
The FICON feature has the following requirements:
-
You can implement FICON features in the following switches:
- Any switch in the Cisco MDS 9500 Series
- Any switch in the Cisco MDS 9200 Series (including the Cisco MDS 9222i Multiservice Modular Switch)
- Cisco MDS 9134 Multilayer Fabric Switch
- MDS 9000 Family 18/4-Port Multiservice Module
- You need the MAINFRAME_PKG license to configure FICON parameters.
- To extend your FICON configuration over a WAN link using FCIP, you need the appropriate SAN_EXTN_OVER_IP license for the module you are using. For more information, refer to the Cisco NX-OS Family Licensing Guide .
Cisco MDS-Specific FICON Advantages
This section explains the additional FICON advantages in Cisco MDS switches and includes the following topics:
Fabric Optimization with VSANs
Generally, separate physical fabrics have a high level of switch management and have a higher implementation cost. The ports in each island also may be over-provisioned depending on the fabric configuration.
By using the Cisco MDS-specific VSAN technology, you can have greater efficiency between these physical fabrics by lowering the cost of over-provisioning and reducing the number of switches to be managed. VSANs also help you to move unused ports nondisruptively and provide a common redundant physical infrastructure (see Figure 1).
![](/c/dam/en/us/td/i/100001-200000/100001-110000/105001-106000/105212.ps/_jcr_content/renditions/105212.jpg)
VSANs enable global SAN consolidation by allowing you to convert existing SAN islands into virtual SAN islands on a single physical network. It provides hardware-enforced security and separation between applications or departments to allow coexistence on a single network. It also allows virtual rewiring to consolidate your storage infrastructure. You can move assets between departments or applications without the expense and disruption of physical relocation of equipment.
![]() Note |
You can configure VSANs in any Cisco MDS switch, but you only can enable FICON in up to eight of these VSANs. The number of VSANs configured depends on the platform. |
Mainframe users can think of VSANs as being like FICON LPARs in the MDS SAN fabric. You can partition switch resources into FICON LPARs (VSANs) that are isolated from each other, in much the same way that you can partition resources on a zSeries or DS8000. Each VSAN has its own set of fabric services (such as fabric server and name server), FICON CUP, domain ID, Fabric Shortest Path First (FSPF) routing, operating mode, IP address, and security profile. FICON LPARs can span line cards and are dynamic in size. For example, one FICON LPAR with 10 ports can span 10 different line cards. FICON LPARs can also include ports on more than one switch in a cascaded configuration. The consistent fairness of the Cisco MDS 9000 switching architecture means that “all ports are created equal,” simplifying provisioning by eliminating the “local switching” issues seen on other vendors’ platforms. Addition of ports to a FICON LPAR is a nondisruptive process. The maximum number of ports for a FICON LPAR is 255 due to FICON addressing limitations.
FCIP Support
The multilayer architecture of the Cisco MDS 9000 Family enables a consistent feature set over a protocol-agnostic switch fabric. Cisco MDS 9500 Series and 9200 Series switches transparently integrate Fibre Channel, FICON, and Fibre Channel over IP (FCIP) in one system. The FICON over FCIP feature enables cost-effective access to remotely located mainframe resources. With the Cisco MDS 9000 Family platform, storage replication services such as IBM PPRC and XRC can be extended over metro to global distances using ubiquitous IP infrastructure which simplifies business continuance strategies.
Refer to the Cisco MDS 9000 Family NX-OS IP Services Configuration Guide .
PortChannel Support
The Cisco MDS implementation of FICON provides support for efficient utilization and increased availability of Inter-Switch Links (ISLs) necessary to build stable large-scale SAN environments. PortChannels ensure an enhanced ISL availability and performance in Cisco MDS switches.
Refer to the Cisco MDS 9000 Family NX-OS Interfaces Configuration Guide for more information on PortChannels.
VSANs for FICON and FCP Mixing
Cisco MDS 9000 Family FICON-enabled switches simplify deployment of even the most complex mixed environments. Multiple logical FICON, Z-Series Linux/FCP, and Open-Systems Fibre Channel Protocol (FCP) fabrics can be overlaid onto a single physical fabric by simply creating VSANs as required for each service. VSANs provide both hardware isolation and protocol specific fabric services, eliminating the complexity and potential instability of zone-based mixed schemes.
By default, the FICON feature is disabled in all switches in the Cisco MDS 9000 Family. When the FICON feature is disabled, FC IDs can be allocated seamlessly. Mixed environments are addressed by the Cisco NX-OS software. The challenge of mixing FCP and FICON protocols are addressed by Cisco MDS switches when implementing VSANs.
Switches and directors in the Cisco MDS 9000 Family support FCP and FICON protocol mixing at the port level. If these protocols are mixed in the same switch, you can use VSANs to isolate FCP and FICON ports.
![]() Tip |
When creating a mixed environment, place all FICON devices in one VSAN (other than the default VSAN) and segregate the FCP switch ports in a separate VSAN (other than the default VSAN). This isolation ensures proper communication for all connected devices. |
Cisco MDS-Supported FICON Features
The Cisco MDS 9000 Family FICON features include:
- Flexibility and investment protection—The Cisco MDS 9000 Family shares common switching and service modules across the Cisco MDS 9500 Series and the 9200 Series.
Refer to the Cisco MDS 9500 Series Hardware Installation Guide and the Cisco MDS 9200 Series Hardware Installation Guide.
- High-availability FICON-enabled director—The Cisco MDS 9500 Series combines nondisruptive software upgrades, stateful process restart and failover, and full redundancy of all major components for a new standard in director-class availability. It supports up to 528 autosensing, 4/2/1-Gbps, 10-Gbps, FICON or FCP ports in any combination in a single chassis. Refer to the Cisco MDS 9000 Family NX-OS High Availability and Redundancy Configuration Guide .
- Infrastructure protection—Common software releases provide infrastructure protection across all Cisco MDS 9000 platforms. Refer to the Cisco MDS 9000 Family NX-OS Software Upgrade and Downgrade Guide .
- VSAN technology—The Cisco MDS 9000 Family provides VSAN technology for hardware-enforced, isolated environments within a single physical fabric for secure sharing of physical infrastructure and enhanced FICON mixed support. See Chapter 19, “Configuring and Managing VSANs.”
- Port-level configurations—There are BB_credits, beacon mode, and port security for each port. Refer to the Cisco MDS 9000 Family NX-OS Interfaces Configuration Guide for information about buffer-to-buffer credits, beacon LEDs, and trunking.
- Alias name configuration—Provides user-friendly aliases instead of the WWN for switches and attached node devices. See Chapter 16, “Configuring and Managing Zones.”
- Comprehensive security framework—The Cisco MDS 9000 Family supports RADIUS and TACACS+ authentication, Simple Network Management Protocol Version 3 (SNMPv3), role-based access control, Secure Shell Protocol (SSH), Secure File Transfer Protocol (SFTP), VSANs, hardware-enforced zoning, ACLs, fabric binding, Fibre Channel Security Protocol (FC-SP), LUN zoning, read-only zones, and VSAN-based access control. Refer to the Cisco MDS 9000 Family NX-OS Security Configuration Guide for information about RADIUS, TACACS+, FC-SP, and DHCHAP.
- Traffic encryption—IPsec is supported over FCIP. You can encrypt FICON and Fibre Channel traffic that is carried over FCIP. Refer to the Cisco MDS 9000 Family NX-OS Security Configuration Guide .
- Local accounting log—View the local accounting log to locate FICON events. For more information about MSCHAP authentication, and local AAA services, refer to the Cisco MDS 9000 Family NX-OS Security Configuration Guide .
- Unified storage management—Cisco MDS 9000 FICON-enabled switches are fully IBM CUP standard compliant for in-band management using the IBM S/A OS/390 I/O operations console. See the CUP In-Band Management.
- Port address-based configurations—Configure port name, blocked or unblocked state, and the prohibit connectivity attributes can be configured on the ports. See the Configuring FICON Ports.
-
You can display the following information:
- Individual Fibre Channel ports, such as the port name, port number, Fibre Channel address, operational state, type of port, and login data.
- Nodes attached to ports.
- Port performance and statistics.
See the Calculating FICON Flow Load Balance.
- Configuration files—Store and apply configuration files. See the FICON Configuration Files.
- FICON and Open Systems Management Server features if installed. —See the VSANs for FICON and FCP Mixing.
- Enhanced cascading support—See the CUP In-Band Management.
- Date and time—Set the date and time on the switch. See the Allowing the Host to Control the Timestamp.
- Configure SNMP trap recipients and community names—See the Configuring SNMP Control of FICON Parameters.
- Call Home configurations—Configure the director name, location, description, and contact person. Refer to the Cisco MDS 9000 Family NX-OS System Management Configuration Guide.
- Configure preferred domain ID, FC ID persistence, and principal switch priority—For information about configuring domain parameters, refer to the Cisco MDS 9000 Family NX-OS System Management Configuration Guide .
- Sophisticated SPAN diagnostics—The Cisco MDS 9000 Family provides industry-first intelligent diagnostics, protocol decoding, and network analysis tools as well as integrated Call Home capability for added reliability, faster problem resolution, and reduced service costs. For information about monitoring network traffic using SPAN, refer to the Cisco MDS 9000 Family NX-OS System Management Configuration Guide .
- Configure R_A_TOV, E_D_TOV—— See the “Fibre Channel Time-Out Values” section on page 27-2 .
- Director-level maintenance tasks—Perform maintenance tasks for the director including maintaining firmware levels, accessing the director logs, and collecting data to support failure analysis. For information about monitoring system processes and logs refer to the Cisco MDS 9000 Family NX-OS System Management Configuration Guide .
- Port-level incident alerts—Display and clear port-level incident alerts. See the Clearing RLIR Information.
FICON Cascading
The Cisco MDS NX-OS software allows multiple switches in a FICON network. To configure multiple switches, you must enable and configure fabric binding in that switch (see the Calculating FICON Flow Load Balance and refer to the Cisco MDS 9000 Family NX-OS Security Configuration Guide ).
FICON VSAN Prerequisites
To ensure that a FICON VSAN is operationally up, be sure to verify the following requirements:
- Set the default zone to permit, if you are not using the zoning feature. See the “About the Default Zone” section on page 16-5 .
- Enable in-order delivery on the VSAN. See Chapter 22, “Configuring Fibre Channel Routing Services and Protocols.”
- Enable (and if required, configure) fabric binding on the VSAN. See the Calculating FICON Flow Load Balance. For more information about Fabric Binding, refer to the Cisco MDS 9000 Family NX-OS Security Configuration Guide .
- Verify that conflicting persistent FC IDs do not exist in the switch. For information about configuring domain parameters, refer to the Cisco MDS 9000 Family NX-OS System Management Configuration Guide .
- Verify that the configured domain ID and requested domain ID match. For information about configuring domain parameters, refer to the Cisco MDS 9000 Family NX-OS System Management Configuration Guide .
- Add the CUP (area FE) to the zone, if you are using zoning. See the CUP In-Band Management.
If any of these requirements are not met, the FICON feature cannot be enabled.
FICON Port Numbering
With reference to the FICON feature, ports in Cisco MDS switches are identified by a statically defined 8-bit value known as the port number. A maximum of 255 port numbers are available. You can use the following port numbering schemes:
- Default port numbers based on the chassis type
- Reserved port numbers
Default FICON Port Numbering Scheme
Default FICON port numbers are assigned by the Cisco MDS NX-OS software based on the module and the slot in the chassis. The first port in a switch always starts with a zero (0) (see Figure 1).
![](/c/dam/en/us/td/i/100001-200000/100001-110000/105001-106000/105217.ps/_jcr_content/renditions/105217.jpg)
The default FICON port number is assigned based on the front panel location of the port and is specific to the slot in which the module resides. Thirty-two (32) port numbers are assigned to each slot on all Cisco MDS 9000 Family switches except for the Cisco MDS 9513 Director, which has 16 port numbers assigned for each slot. These default numbers are assigned regardless of the module’s physical presence in the chassis, the port status (up or down), or the number of ports on the module (4, 12, 16, 24, or 48). If a module has fewer ports than the number of port numbers assigned to the slot, then the excess port numbers are unused. If a module has more ports than the number of port numbers assigned to the slot, the excess ports cannot be used for FICON traffic unless you manually assign the port numbers.
![]() Note |
You can use the ficon slot assign port-numbers command to make use of any Follow the steps in Assigning FICON Port Numbers to Slots to make use ofexcess ports by manually assigning more port numbers to the slots. Before doing this, however, we recommend that you review the default port number assignments for Cisco MDS 9000 switches shown in Table 1 and Table 1, and that you read the following sections to gain a complete understanding of FICON port numbering: About the Reserved FICON Port Numbering Scheme, FICON Port Numbering Guidelines, and Assigning FICON Port Numbers to Slots. |
![]() Note |
Only Fibre Channel, PortChannel, and FCIP ports are mapped to FICON port numbers. Other types of interfaces do not have a corresponding port number. |
Table 1 lists the default port number assignment for the Cisco MDS 9000 Family of switches and directors.
Product | Slot Number | Implemented Port Allocation | Unimplemented Ports | Notes | |
To Ports | To PortChannel/FCIP | ||||
Cisco MDS 9200 Series | Slot 1 | 0 through 31 | 64 through 89 | 90 through 253 and port 255 | Similar to a switching module. |
Slot 2 | 32 through 63 | ||||
Cisco MDS 9222i Series | Slot 1 | 0 through 31 | 64 through 89 | 90 through 253 and port 255 | The first 4, 12, 16, or 24 port numbers in a 4-port, 12-port, 16-port, or 24-port module are used and the rest remain unused. Extra 16 ports on 48-port modules are not allocated numbers. |
Slot 2 | 32 through 63 | ||||
Cisco MDS 9506 Director | Slot 1 | 0 through 31 | 128 through 153 | 154 through 253 and port 255 | Supervisor modules are not allocated port numbers. |
Slot 2 | 32 through 63 | ||||
Slot 3 | 64 through 95 | ||||
Slot 4 | 96 through 127 | ||||
Slot 5 | None | ||||
Slot 6 | None | ||||
Cisco MDS 9134 Director | Slot 1 | 0 through 33 | 34 through 59 | 60 through 253 and port 255 | |
Cisco MDS 9509 Director | Slot 1 | 0 through 31 | 224 through 249 | 250 through 253 and port 255 | The first 4, 12, 16, or 24 port numbers in a 4-port, 12-port, 16-port, or 24-port module are used and the rest remain unused. Extra 16 ports on 48-port modules are not allocated port numbers. |
Slot 2 | 32 through 63 | ||||
Slot 3 | 64 through 95 | ||||
Slot 4 | 96 through 127 | ||||
Slot 5 | None | Supervisor modules are not allocated port numbers. | |||
Slot 6 | None | ||||
Slot 7 | 128 through 159 | The first 4, 12, 16, or 24 port numbers are used for a 4-port, 12-port,16-port, or 24-port module and the rest remain unused. Extra 16 ports on 48-port modules are not allocated port numbers. | |||
Slot 8 | 160 through 191 | ||||
Slot 9 | 192 through 223 | ||||
Cisco MDS 9513 Director | Slot 1 | 0 through 15 | 224 through 249 | 250 through 253 and port 255 | The first 4, 12 or 16 port numbers are used for a 4-port, 12-port or 16-port module and the rest remain unused. Extra ports on 24-port, 32-port, and 48-port modules are not allocated port numbers. |
Slot 2 | 16 through 31 | ||||
Slot 3 | 32 through 47 | ||||
Slot 4 | 48 through 63 | ||||
Slot 5 | 64 through 79 | ||||
Slot 6 | 80 through 95 | ||||
Slot 7 | None | Supervisor modules are not allocated port numbers. | |||
Slot 8 | None | ||||
Slot 9 | 96 through 111 | The first 4 or 12 port numbers are used for a 4-port or 12-port module and the rest remain unused. Extra ports on 24-port, 32-port, and 48-port modules are not allocated port numbers. | |||
Slot 10 | 112 through 127 | ||||
Slot 11 | 128 through 143 | ||||
Slot 12 | 144 through 159 | ||||
Slot 13 | 160 through 175 |
Port Addresses
By default, port numbers are the same as port addresses. You can swap the port addresses (see the Port Swapping).
Implemented and Unimplemented Port Addresses
An implemented port refers to any port address that is assigned by default to a slot in the chassis (see Default Settings). An unimplemented port refers to any port address that is not assigned by default to a slot in the chassis (see Default Settings).
About the Reserved FICON Port Numbering Scheme
A range of 250 port numbers are available for you to assign to all the ports on a switch. Default Settings shows that you can have more than 250 physical ports on a switch and the excess ports do not have port numbers in the default numbering scheme. When you have more than 250 physical ports on your switch, you can have ports without a port number assigned if they are not in a FICON VSAN, or you can assign duplicate port numbers if they are not used in the same FICON VSAN. For example, you can configure port number 1 on interface fc1/1 in FICON VSAN 10 and fc10/1 in FICON VSAN 20.
![]() Note |
A VSAN can have a maximum of 250 port numbers. |
![]() Note |
FICON port numbers are not changed for ports that are active. You must first disable the interfaces using the shutdown command. |
![]() Note |
You can configure port numbers even when no module is installed in the slot. |
Installed and Uninstalled Ports
An installed port refers to a port for which all required hardware is present. A specified port number in a VSAN can be implemented, and yet not installed, if any of the following conditions apply:
- The module is not present—For example, if module 1 is not physically present in slot 1 in a Cisco MDS 9509 Director, ports 0 to 31 are considered uninstalled.
- The small form-factor pluggable (SFP) port is not present—For example, if a 16-port module is inserted in slot 2 in a Cisco MDS 9509 Director, ports 48 to 63 are considered uninstalled.
- For slot 1, ports 0 to 31, or 0 to 15 have been assigned. Only the physical port fc1/5 with port number 4 is in VSAN 2. The rest of the physical ports are not in VSAN 2. The port numbers 0 to 249 are considered implemented for any FICON-enabled VSAN. Therefore, VSAN 2 has port numbers 0 to 249 and one physical port, fc1/4. The corresponding physical ports 0 to 3,and 5 to 249 are not in VSAN 2. When the FICON VSAN port address is displayed, those port numbers with the physical ports not in VSAN 2 are not installed (for example, ports 0 to 3, or 5 to 249).
Another scenario is if VSANs 1 through 5 are FICON-enabled, and trunking-enabled interface fc1/1 has VSANs 3 through 10, then port address 0 is uninstalled in VSAN 1 and 2.
- The port is part of a PortChannel—For example, if interface fc 1/1 is part of PortChanne1 5, port address 0 is uninstalled in all FICON VSANs. See Default Settings.
About Port Numbers for FCIP and PortChannel
FCIP and PortChannels cannot be used in a FICON-enabled VSAN unless they are explicitly bound to a port number.
See the Configuring FICON Ports, Configuring FICON Ports, Reserving FICON Port Numbers for FCIP and PortChannel Interfaces, and Binding Port Numbers to FCIP Interfaces.
You can use the default port numbers if they are available (see Default FICON Port Numbering Scheme) or if you reserve port numbers from the pool of port numbers that are not reserved for Fibre Channel interfaces (see the FICON Port Numbering and the About the Reserved FICON Port Numbering Scheme).
FC ID Allocation
FICON requires a predictable and static FC ID allocation scheme. When FICON is enabled, the FC ID allocated to a device is based on the port address of the port to which it is attached. The port address forms the middle byte of the fabric address. Additionally, the last byte of the fabric address should be the same for all devices in the fabric. By default, the last byte value is 0 and can be configured (see the Assigning FC ID Last Byte).
![]() Note |
You cannot configure persistent FC IDs in FICON-enabled VSANs. |
Cisco MDS switches have a dynamic FC ID allocation scheme. When FICON is enabled or disabled on a VSAN, all the ports are shut down and restarted to switch from the dynamic to static FC IDs and vice versa (see Figure 1).
![](/c/dam/en/us/td/i/100001-200000/110001-120000/113001-114000/113134.ps/_jcr_content/renditions/113134.jpg)
About Enabling FICON on a VSAN
By default FICON is disabled in all VSANs on the switch.
You can enable FICON on a per VSAN basis in one of the following ways:
- Use the automated setup ficon command.
See the Setting Up a Basic FICON Configuration.
- Manually address each prerequisite.
See the Information About FICON.
- Use Device Manager (refer to the Fabric Configuration Guide, Cisco DCNM for SAN).
When you enable the FICON feature in Cisco MDS switches, the following restrictions apply:
- You cannot disable in-order delivery for the FICON-enabled VSAN.
- You cannot disable fabric binding or static domain ID configurations for the FICON-enabled VSAN.
- The load balancing scheme is changed to Source ID (SID)—Destination ID (DID). You cannot change it back to SID—DID—OXID.
- The IPL configuration file is automatically created.
See the FICON Configuration Files.
FICON Information Refresh
When viewing FICON information through the Device Manager dialog boxes, you must manually refresh the display by clicking the Refresh button to see the latest updates. You need to take this step whether you configure FICON through the CLI or through the Device Manager.
There is no automatic refresh of FICON information. This information would be refreshed so often that it would affect performance.
About FICON Device Allegiance
FICON requires serialization of access among multiple mainframes, CLI, and SNMP sessions be maintained on Cisco MDS 9000 Family switches by controlling device allegiance for the currently executing session. Any other session is denied permission to perform configuration changes unless the required allegiance is available.
![]() Caution |
This task discards the currently executing session. |
Automatically Saving the Running Configuration
Cisco MDS NX-OS provides an option to automatically save any configuration changes to the startup configuration. This ensures that the new configuration is present after a switch reboot. By default, the Active=Saved active equals saved option is automatically enabled on any FICON VSAN.
The following table displays the results of the Active = Saved option active equals saved command and the implicit copy from the running configuration to the startup configuration ( copy running start ) copy running-config startup-config command in various scenarios.
When the Active=Saved option active equals saved command is enabled in any FICON-enabled VSAN in the fabric, then the following apply:
-
All configuration changes (FICON-specific or not) are automatically saved to persistent storage (implicit copy running start ) and stored in the startup configuration.
-
FICON-specific configuration changes are immediately saved to the IPL file (see the “FICON Configuration Files” section).
If the Active=Saved option active equals saved command is not enabled in any FICON-enabled VSAN in the fabric, then FICON-specific configuration changes are not saved in the IPL file and an implicit copy running startup command is not issued, you must explicitly save the running configuration to the startup configuration issue the copy running start command explicitly.
Number |
FICON-enabled VSAN? |
active equals saved Enabled? |
Implicit copy running start Issued? 1 |
Notes |
---|---|---|---|---|
1 |
Yes |
Yes (in all FICON VSANs) |
Implicit |
FICON changes written to the IPL file. Non-FICON changes saved to startup configuration and persistent storage. |
2 |
Yes |
Yes (even in one FICON VSAN) |
Implicit |
FICON changes written to IPL file for only the VSAN that has active equals saved option enabled. Non-FICON changes saved to startup configuration and persistent storage. |
3 |
Yes |
Not in any FICON VSAN |
Not implicit |
FICON changes are not written to the IPL file. Non-FICON changes are saved in persistent storage—only if you explicitly issue the copy running start command. |
4 |
No |
Not applicable |
![]() Note |
If active equals saved is enabled, the Cisco NX-OS software ensures that you do not have to perform the copy running startup command for the FICON configuration as well. If your switch or fabric consists of multiple FICON-enabled VSANs, and one of these VSANs have active equals saved enabled, changes made to the non-FICON configuration results in all configurations being saved to the startup configuration. |
Port Prohibiting
To prevent implemented ports from talking to each other, configure prohibits between two or more ports. If you prohibit ports, the specified ports are prevented from communicating with each other.
![]() Tip |
You cannot prohibit a PortChannel or FCIP interface. |
Unimplemented ports are always prohibited. In addition, prohibit configurations are always symmetrically applied—if you prohibit port 0 from talking to port 15, port 15 is automatically prohibited from talking to port 0.
![]() Note |
If an interface is already configured in E or TE mode and you try to prohibit that port, your prohibit configuration is rejected. Similarly, if a port is not up and you prohibit that port, the port is not allowed to come up in E mode or in TE mode. |
About RLIR
The Registered Link Incident Report (RLIR) application provides a method for a switch port to send a Link Incident Record (LIR) to a registered Nx port.
When an LIR is detected in FICON-enabled switches in the Cisco MDS 9000 Family from an RLIR Extended Link Service (ELS), the switch sends that record to the members in its Established Registration List (ERL).
In case of multiswitch topology, a Distribute Registered Link Incident Record (DRLIR) Inter-Link Service (ILS) is sent to all reachable remote domains along with the RLIR ELS. On receiving the DRLIR ILS, the switch extracts the RLIR ELS and sends it to the members of the ERL.
The Nx ports interested in receiving the RLIR ELS send the Link Incident Record Registration (LIRR) ELS request to the management server on the switch. The RLIRs are processed on a per-VSAN basis.
The RLIR data is written to persistent storage when you copy the running configuration to the startup configuration.
FICON Configuration Files
You can save up to 16 FICON configuration files on each FICON-enabled VSAN (in persistent storage). The file format is proprietary to IBM. These files can be read and written by IBM hosts using the in-band CUP protocol. Additionally, you can use the Cisco MDS CLI or DCNM-SAN applications to operate on these FICON configuration files.
![]() Note |
Multiple FICON configuration files with the same name can exist in the same switch, provided they reside in different VSANs. For example, you can create a configuration file named XYZ in both VSAN 1 and VSAN 3. |
When you enable the FICON feature in a VSAN, the switches always use the startup FICON configuration file, called IPL. This file is created with a default configuration as soon as FICON is enabled in a VSAN.
![]() Caution |
When FICON is disabled on a VSAN, all the FICON configuration files are irretrievably lost. |
FICON configuration files contain the following configuration for each implemented port address:
- Block
- Prohibit mask
- Port address name
![]() Note |
Normal configuration files used by Cisco MDS switches include FICON-enabled attributes for a VSAN, port number mapping for PortChannels and FCIP interfaces, port number to port address mapping, port and trunk allowed VSAN configuration for ports, in-order guarantee, static domain ID configuration, and fabric binding configuration. |
Refer to the Cisco MDS 9000 Family NX-OS Fundamentals Configuration Guide for details on the normal configuration files used by Cisco MDS switches.
Only one user can access the configuration file at any given time:
- If this file is being accessed by user 1, user 2 cannot access this file.
- If user 2 does attempt to access this file, an error is issued to user 2.
- If user 1 is inactive for more than 15 seconds, the file is automatically closed and available for use by any other permitted user.
FICON configuration files can be accessed by any host, SNMP, or CLI user who is permitted to access the switch. The locking mechanism in the Cisco NX-OS software restricts access to one user at a time per file. This lock applies to newly created files and previously saved files. Before accessing any file, you must lock the file and obtain the file key. A new file key is used by the locking mechanism for each lock request. The key is discarded when the lock timeout of 15 seconds expires. The lock timeout value cannot be changed.
Port Swapping
The FICON port-swapping feature is only provided for maintenance purposes.
The FICON port-swapping feature causes all configurations associated with old-port-number and new port-number to be swapped, including VSAN configurations.
Cisco MDS switches allow port swapping for nonexistent ports as follows:
- Only FICON-specific configurations (prohibit, block, and port address mapping) are swapped.
- No other system configuration is swapped.
- All other system configurations are only maintained for existing ports.
- If you swap a port in a module that has unlimited oversubscription ratios enabled with a port in a module that has limited oversubscription ratios, then you may experience a degradation in bandwidth.
![]() Tip |
If you check the Active=Saved check box active equals saved is enabled on any FICON VSAN, then the swapped configuration is automatically saved to startup. Otherwise, you must explicitly save the running configuration immediately after swapping the ports. |
Once you swap ports, the switch automatically performs the following actions:
- Shuts down both the old and new ports.
- Swaps the port configuration.
If you attempt to bring the port up, you must explicitly shut down the port to resume traffic.
![]() Note |
To view the latest FICON information, you must click the Refresh button. See the Automatically Saving the Running Configuration. |
FICON Tape Acceleration
The sequential nature of tape devices causes each I/O operation to the tape device over an FCIP link to incur the latency of the FCIP link. Throughput drastically decreases as the round-trip time through the FCIP link increases, leading to longer backup windows. Also, after each I/O operation, the tape device is idle until the next I/O arrives. Starting and stopping of the tape head reduces the lifespan of the tape, except when I/O operations are directed to a virtual tape.
Cisco MDS NX-OS software provides acceleration for the following FICON tape write operations:
-
The link between mainframe and native tape drives (both IBM and Sun/STK)
-
The back-end link between the VSM (Virtual Storage Management) and tape drive (Sun/STK)
FICON tape acceleration over FCIP provides the following advantages:
-
Efficiently utilizes the tape device by decreasing idle time
-
More sustained throughput as latency increases
-
Similar to FCP tape acceleration, and does not conflict with it
![]() Note |
FICON tape read acceleration over FCIP is supported from Cisco MDS NX-OS Release 5.0(1). For more information refer to the Configuring FICON Tape Read Acceleration. |
Figure 1 through Figure 4 show supported configurations.
![](/c/dam/en/us/td/i/100001-200000/140001-150000/144001-145000/144880.ps/_jcr_content/renditions/144880.jpg)
![](/c/dam/en/us/td/i/100001-200000/140001-150000/144001-145000/144881.ps/_jcr_content/renditions/144881.jpg)
![](/c/dam/en/us/td/i/100001-200000/140001-150000/144001-145000/144882.ps/_jcr_content/renditions/144882.jpg)
![](/c/dam/en/us/td/i/100001-200000/140001-150000/144001-145000/144883.ps/_jcr_content/renditions/144883.jpg)
![]() Note |
For information about FCIP tape acceleration, refer to the Cisco MDS 9000 Family NX-OS IP Services Configuration Guide . |
CUP In-Band Management
The CUP protocol configures access control and provides unified storage management capabilities from a mainframe computer. Cisco MDS 9000 FICON-enabled switches are fully IBM CUP standard compliant for in-band management using the IBM S/A OS/390 I/O operations console.
![]() Note |
The CUP specification is proprietary to IBM. |
CUP is supported by switches and directors in the Cisco MDS 9000 Family. The CUP function allows the mainframe to manage the Cisco MDS switches.
Host communication includes control functions such as blocking and unblocking ports, as well as monitoring and error reporting functions.
Licensing Requirements for FICON
The following table shows the licensing requirements for this feature:
License |
License Description |
---|---|
MAINFRAME_PKG |
The mainframe license is required to enable FICON. For a complete explanation of the licensing scheme, see the Cisco MDS 9000 Family NX-OS Licensing Guide . |
XRC_ACCL |
The Extended Remote Copy (XRC) acceleration is required to activate FICON XRC acceleration on the Cisco MDS 9222i Switch and on the MSM-18/4 module in the Cisco MDS 9500 Series directors. For a complete explanation of the NX-OS licensing scheme and how to obtain and apply licenses, see the Cisco MDS 9000 Family NX-OS Licensing Guide. |
Guidelines and Limitations
This section includes the guidelines and limitations for this feature:
FICON Port Numbering Guidelines
The following guidelines apply to FICON port numbers:
- Supervisor modules do not have port number assignments.
- Port numbers do not change based on TE ports. Since TE ports appear in multiple VSANs, chassis-wide unique port numbers should be reserved for TE ports.
- Each PortChannel must be explicitly associated with a FICON port number.
- When the port number for a physical PortChannel becomes uninstalled, the relevant PortChannel configuration is applied to the physical port.
- Each FCIP tunnel must be explicitly associated with a FICON port number. If the port numbers are not assigned for PortChannels or for FCIP tunnels, then the associated ports will not come up.
Port Swapping Guidelines
Be sure to follow these guidelines when using the FICON port swapping feature:
- Port swapping is not supported for logical ports (PortChannels, FCIP links). Neither the old-port-number nor the new-port-number can be a logical port.
- Port swapping is not supported between physical ports that are part of a PortChannel. Neither the old-port-number nor the new-port-number can be a physical port that is part of a PortChannel.
- Before performing a port swap, the Cisco NX-OS software performs a compatibility check. If the two ports have incompatible configurations, the port swap is rejected with an appropriate reason code. For example, if a port with BB_credits as 25 is being swapped with an OSM port for which a maximum of 12 BB_credits is allowed (not a configurable parameter), the port swapping operation is rejected.
- Before performing a port swap, the Cisco NX-OS software performs a compatibility check to verify the extended BB_credits configuration.
- If ports have default values (for some incompatible parameters), then a port swap operation is allowed and the ports retain their default values.
- Port tracking information is not included in port swapping. This information must be configured separately (refer to the Cisco MDS 9000 Family NX-OS Quality of Service Configuration Guide ).
![]() Note |
The 32-port module guidelines also apply for port swapping configurations (Refer to the Cisco MDS 9000 Family NX-OS Interfaces Configuration Guide ). |
FICON Tape Acceleration Configuration Guidelines
FICON tape acceleration has the following configuration guidelines:
- In addition to the normal FICON configuration, FICON tape acceleration must be enabled on both ends of the FCIP interface. If only one end has FICON tape acceleration enabled, acceleration does not occur.
- FICON tape acceleration is enabled on a per VSAN basis.
- FICON tape acceleration cannot function if multiple ISLs are present in the same VSAN (PortChannels or FSPF load balanced).
- You can enable both Fibre Channel write acceleration and FICON tape acceleration on the same FCIP interface.
Enabling or disabling FICON tape acceleration disrupts traffic on the FCIP interface.
Default Settings
Table 1 lists the default settings for FICON features.
Parameters |
Default |
---|---|
FICON feature |
Disabled. |
Port numbers |
Same as port addresses. |
FC ID last byte value |
0 (zero). |
EBCDIC format option |
US-Canada. |
Switch offline state |
Hosts are allowed to move the switch to an offline state. |
Mainframe users |
Allowed to configure FICON parameters on Cisco MDS switches. |
Clock in each VSAN |
Same as the switch hardware clock. |
Host clock control |
Allows host to set the clock on this switch. |
SNMP users |
Configure FICON parameters. |
Port address |
Not blocked. |
Prohibited ports |
Ports 90–253 and 255 for the Cisco MDS 9200 Series switches. Ports 250–253 and 255 for the Cisco MDS 9500 Series switches. |
Configuring FICON
By default FICON is disabled in all switches in the Cisco MDS 9000 Family. You can enable FICON on a per VSAN basis by using the Device Manager.
Assigning FICON Port Numbers to Slots
![]() Caution |
When you assign, change, or release a port number, the port reloads. |
To assign FICON port numbers to slots using Device Manager, follow these steps:
Procedure
Step 1 |
Click FICON and then select Port Numbers . You see the FICON port number. |
Step 2 |
Enter the chassis slot port numbers in the Reserved Port Numbers field. |
Step 3 |
Click Apply . |
Reserving FICON Port Numbers for FCIP and PortChannel Interfaces
You must reserve port numbers for logical interfaces, such as FCIP and PortChannels, if you plan to use them.
To reserve FICON port numbers for FCIP and PortChannel interfaces using Device Manager, follow these steps:
Procedure
Step 1 |
Click FICON > Port Numbers. You see the FICON port numbers dialog box. |
Step 2 |
Click the Logical tab to see the reserved port numbers for the slot. |
Step 3 |
Enter the chassis slot port numbers. These are the reserved port numbers for one chassis slot. There can be up to 64 port numbers reserved for each slot in the chassis. |
Step 4 |
Click Apply . |
Setting Up a Basic FICON Configuration
This section steps you through the procedure to set up FICON on a specified VSAN in a Cisco MDS 9000 Family switch.
![]() Note |
Press Ctrl-C at any prompt to skip the remaining configuration options and proceed with what is configured until that point. |
![]() Tip |
If you do not want to answer a previously configured question, or if you want to skip answers to any questions, press Enter . If a default answer is not available (for example, switch name), the switch uses what was previously configured and skips to the next question. |
To enable and set up FICON, follow these steps:
Procedure
Step 1 |
Enter the setup ficon command at the EXEC command mode. Example:
|
||
Step 2 |
Enter yes (the default is yes ) to enter the basic FICON configuration setup. Example:
The FICON setup utility guides you through the basic configuration process. Press Ctrl-C at any prompt to end the configuration process. |
||
Step 3 |
Enter the VSAN number for which FICON should be enabled. Example:
|
||
Step 4 |
Enter yes (the default is yes ) to create a VSAN. Example:
|
||
Step 5 |
Enter yes (the default is yes ) to confirm your VSAN choice: Example:
|
||
Step 6 |
Enter the domain ID number for the specified FICON VSAN. Example:
|
||
Step 7 |
Enter yes (the default is no ) to set up FICON in cascaded mode. If you enter no , skip to Step 8 (see the CUP In-Band Management). Example:
|
||
Step 8 |
Enter yes (the default is yes ) to allow SNMP permission to modify existing port connectivity parameters (see the Configuring SNMP Control of FICON Parameters). Example:
|
||
Step 9 |
Enter no (the default is no ) to allow the host (mainframe) to modify the port connectivity parameters, if required (see the Allowing the Host to Change FICON Port Parameters). Example:
|
||
Step 10 |
Enter yes (the default is yes ) to enable the active equals saved feature (see the Automatically Saving the Running Configuration). Example:
|
||
Step 11 |
Enter yes (the default is yes ) if you wish to configure additional FICON VSANs. Example:
|
||
Step 12 |
Review and edit the configuration that you have just entered. |
||
Step 13 |
Enter no (the default is no ) if you are satisfied with the configuration.
Example:
|
||
Step 14 |
Enter yes (the default is yes ) to use and save this configuration. The implemented commands are displayed. After FICON is enabled for the specified VSAN, you are returned to the EXEC mode switch prompt. Example:
Example:
|
Enabling FICON on a VSAN
To create a FICON-enabled VSAN, follow these steps:
Procedure
Step 1 |
Click the Create VSAN icon (see Figure 1). ![]() You see the Create VSAN dialog box. |
||
Step 2 |
Select the switches you want to be in the VSAN. |
||
Step 3 |
Enter a VSAN ID. |
||
Step 4 |
Enter the name of the VSAN, if desired. |
||
Step 5 |
Select the type of load balancing, the interop value, and the administrative state for this VSAN. |
||
Step 6 |
Check the FICON check box.
|
||
Step 7 |
Check the option, if appropriate, to enable fabric binding for the selected switches. |
||
Step 8 |
Check the All Ports Prohibited option if all ports in this VSAN are prohibited. |
||
Step 9 |
Click Create to create the VSAN. |
||
Step 10 |
Choose Tools > Device Manager to open Device Manager for each switch in the FICON VSAN. |
||
Step 11 |
Choose FC > VSANs. You see the VSAN dialog box. |
||
Step 12 |
Enter the VSAN membership information. |
||
Step 13 |
Click the VSAN you want to become a FICON VSAN and select Add from the FICON drop-down menu. |
||
Step 14 |
Click Apply to save these changes. |
Manually Enabling FICON on a VSAN
![]() Note |
This section describes the procedure to manually enable FICON on a VSAN. If you have already enabled FICON on the required VSAN using the automated setup (recommended), skip to the Automatically Saving the Running Configuration. |
To manually enable FICON on a VSAN, follow these steps:
Procedure
Step 1 |
Choose VSAN > FICON . You see the FICON VSAN configuration information in the Information pane. |
Step 2 |
Select the switch in the VSAN on which you want to enable FICON. |
Step 3 |
Click enable from the Command drop-down menu. |
Step 4 |
Click the Apply Changes icon to save these changes. |
Deleting FICON VSANs
To delete a FICON VSAN, follow these steps:
Procedure
Step 1 |
Select All VSANS. You see the VSAN table in the Information pane. |
||
Step 2 |
Click anywhere in the row of the VSAN that you want to delete. |
||
Step 3 |
Click Delete Row to delete the VSAN.
|
Suspending a FICON VSAN
To suspend a FICON VSAN, follow these steps:
Procedure
Step 1 |
Click All VSANs . You see all the VSANs listed in the Information pane. |
Step 2 |
Select the VSAN that you want to suspend. |
Step 3 |
Set the Admin drop-down menu for a VSAN to suspended. |
Step 4 |
Click the Apply Changes icon to save these changes. |
What to do next
![]() Note |
This command can be issued by the host if the host is allowed to do so (see the Allowing the Host to Move the Switch Offline). |
Configuring the code-page Option
FICON strings are coded in Extended Binary-Coded Decimal Interchange Code (EBCDIC) format. Refer to your mainframe documentation for details on the code-page options.
Cisco MDS switches support international-5 , france , brazil , germany , italy , japan , spain-latinamerica , uk , and us-canada (default) EBCDIC format options.
To modify the code-page option using Device Manager, follow these steps:
Procedure
Step 1 |
Choose FICON > VSANs . You see the FICON VSAN configuration dialog box. The VSANs tab is the default tab. |
Step 2 |
From the CodePage drop-down menu, choose an option for the FICON VSAN you want to configure. |
Step 3 |
Click Apply to save the changes. |
Assigning FC ID Last Byte
![]() Note |
If the FICON feature is configured in cascaded mode, the Cisco MDS switches use ISLs to connect to other switches. To assign the last byte for the FC ID, follow these steps: |
Procedure
Step 1 |
Choose All VSANs > Domain Manager. |
Step 2 |
Click the Persistent FCIDs tab. |
Step 3 |
Select single in the Mask column and then assign the entire FC ID at once. The single option allows you to enter the FC ID in the ###### format. |
Step 4 |
Click the Apply Changes icon to save these changes. |
Allowing the Host to Move the Switch Offline
By default, hosts are allowed to move the switch to an offline state. To do this, the host sends a "Set offline" command (x'FD') to the CUP.
To allow the host (mainframe) to move the switch to an offline state, follow these steps:
Procedure
Step 1 |
Choose VSAN > FICON . You see a list of switches under the Control tab in the Information pane. |
Step 2 |
Click the VSANs tab. You see the FICON VSAN configuration information in the Information pane. |
Step 3 |
Check the Host Can Offline Sw check box to allow the mainframe to move a switch to the offline state. |
Step 4 |
Check the Host Can Sync Time check box to allow the mainframe to set the system time on the switch. |
Step 5 |
Click the Apply Changes icon to save the changes. |
Allowing the Host to Change FICON Port Parameters
By default, mainframe users are not allowed to configure FICON parameters on Cisco MDS switches—they can only query the switch.
Use the host port control command to permit mainframe users to configure FICON parameters.
To allow the host (mainframe) to configure FICON parameters on the Cisco MDS switch, follow these steps:
Procedure
Step 1 |
Choose VSAN > FICON . You see a list of switches under the Control tab in the Information pane. |
Step 2 |
Click the VSANs tab. You see the FICON VSAN configuration information in the Information pane. |
Step 3 |
Check the Port Control By Host check box to allow the mainframe to control a switch. |
Step 4 |
Click the Apply Changes icon to save the changes. |
Allowing the Host to Control the Timestamp
By default, the clock in each VSAN is the same as the switch hardware clock. Each VSAN in a Cisco MDS 9000 Family switch represents a virtual director. The clock and time present in each virtual director can be different.To maintain separate clocks for each VSAN, the Cisco NX-OS software maintains the difference of the VSAN-specific clock and the hardware-based director clock. When a host (mainframe) sets the time, the Cisco NX-OS software updates this difference between the clocks. When a host reads the clock, it computes the difference between the VSAN-clock and the current director hardware clock and presents a value to the mainframe.
The VSAN-clock current time is reported in the output of show ficon vsan vsan-id , show ficon , and show accounting log commands.
To configure host (mainframe) control for the VSAN time stamp, follow these steps:
Procedure
Step 1 |
Choose VSAN > FICON . You see a list of switches under the Control tab in the Information pane. |
Step 2 |
Click the VSANs tab. You see the FICON VSAN configuration information in the Information pane. |
Step 3 |
Check the Host Can Sync Time checkbox to allow the mainframe to set the system time on the switch. |
Step 4 |
Click the Apply Changes icon to save these changes. |
Configuring SNMP Control of FICON Parameters
By default, SNMP users can configure FICON parameters using Cisco DCNM for SAN.
![]() Note |
If you disable SNMP in the Cisco MDS switch, you cannot configure FICON parameters using DCNM-SAN. To configure SNMP control of FICON parameters, follow these steps: |
Procedure
Step 1 |
Choose VSAN > FICON . You see a list of switches under the Control tab in the Information pane. |
Step 2 |
Click the VSANs tab. You see the FICON VSAN configuration information in the Information pane. |
Step 3 |
Check the Port Control By SNMP checkbox to allow SNMP users to configure FICON on the switch. |
Step 4 |
Click the Apply Changes icon to save these changes. |
Automatically Saving the Running Configuration
To save the running configuration, follow these steps:
Procedure
Step 1 |
Choose VSAN > FICON . You see a list of switches under the Control tab in the Information pane. |
Step 2 |
Click the VSANs tab. You see the FICON VSAN configuration information in the Information pane. |
Step 3 |
Check the Active=Saved check box to automatically save the running configuration to the startup configuration whenever there is a FICON configuration change. |
Step 4 |
Click the Apply Changes icon to save these changes. |
Configuring FICON Ports
You can perform FICON configurations on a per-port address basis in the Cisco MDS 9000 Family switches.
Even if a port is uninstalled, the port address-based configuration is accepted by the Cisco MDS switch. This configuration is applied to the port when the port becomes installed.
Binding Port Numbers to PortChannels
![]() Caution |
All port number assignments to PortChannels or FCIP interfaces are lost (cannot be retrieved) when FICON is disabled on all VSANs. |
You can bind (or associate) a PortChannel with a FICON port number to bring up that interface.
Binding Port Numbers to FCIP Interfaces
You can bind (or associate) an FCIP interface with a FICON port number to bring up that interface.
Configuring Port Blocking
If you block a port, the port is retained in the operationally down state. If you unblock a port, a port initialization is attempted. When a port is blocked, data and control traffic are not allowed on that port.
Physical Fibre Channel port blocks will continue to transmit an Off-line state (OLS) primitive sequence on a blocked port.
![]() Note |
The shutdown /no shutdown port state is independent of the block /no block port state. |
![]() Note |
You cannot block or prohibit the CUP port (0XFE). If a port is shut down, unblocking that port does not initialize the port. To block or unblock port addresses in a VSAN using Device Manager, follow these steps: |
Procedure
Step 1 |
Choose FICON > VSANs . |
Step 2 |
Select a VSAN ID and click Port Configuration . You see the FICON Port Configuration dialog box for the selected VSAN. |
Step 3 |
Check the Blocked check box for the port that you want to block. |
Step 4 |
Click Apply to save the changes. |
Configuring the Default State for Port Prohibiting
By default, port prohibiting is disabled on the implemented interfaces on the switch. As of Cisco MDS SAN-OS Release 3.0(2), you can change the default port prohibiting state to enabled in VSANs that you create and then selectively disable port prohibiting on implemented ports, if desired. Also, only the FICON configuration files created after you change the default have the new default setting (see the FICON Configuration Files).
Configuring Port Prohibiting
To prohibit port addresses in a VSAN using Device Manager, follow these steps:
Procedure
Step 1 |
Choose FICON > VSANs . |
Step 2 |
Select a VASAN ID and click Port Configuration. You see the FICON Port Configuration dialog box. |
Step 3 |
Set the port prohibit configuration for the selected FICON VSANs. |
Step 4 |
Click Apply to save these changes. |
Assigning a Port Address Name
![]() Note |
To view the latest FICON information, you must click the Refresh button. See the Automatically Saving the Running Configuration. |
To assign a port address name in Device Manager, follow these steps:
Procedure
Step 1 |
Choose FICON > VSANs . |
Step 2 |
Select a VSAN ID and click Port Configuration. You see the FICON Port Configuration dialog box. |
Step 3 |
Enter the Port Configuration information. |
Step 4 |
Click Apply to save the configuration information. |
Specifying an RLIR Preferred Host
As of Cisco MDS SAN-OS Release 3.0(3), you can specify a preferred host to receive RLIR frames. The MDS switch sends RLIR frames to the preferred host only if it meets the following conditions:
- No host in the VSAN is registered for RLIR with the registration function set to “always receive.” If one or more hosts in the VSAN are registered as “always receive,” then RLIR sends only to these hosts and not to the configured preferred host.
- The preferred host is registered with the registration function set to “conditionally receive.”
![]() Note |
If all registered hosts have the registration function set to “conditionally receive,” then the preferred host receives the RLIR frames. |
You can specify only one RLIR preferred host per VSAN. By default, the switch sends RLIR frames to one of the hosts in the VSAN with the register function set to “conditionally receive” if no hosts have the register function set to “always receive.”
Clearing RLIR Information
Use the clear rlir statistics command to clear all existing statistics for a specified VSAN.
switch# clear rlir statistics vsan 1
Use the clear rlir history command to clear the RLIR history where all link incident records are logged for all interfaces.
switch# clear rlir history
Use the clear rlir recent interface command to clear the most recent RLIR information for a specified interface.
switch# clear rlir recent interface fc 1/2
Use the clear rlir recent portnumber command to clear the most recent RLIR information for a specified port number.
switch# clear rlir recent portnumber 16
Applying the Saved Configuration Files to the Running Configuration
To apply the saved configuration files to the running configuration using Device Manager, follow these steps:
Procedure
Step 1 |
Choose FICON > VSANs . |
Step 2 |
Click the Files tab. You see the FICON Files dialog box. |
Step 3 |
Highlight the file you want to apply and click Apply File to apply the configuration to the running configuration. |
Editing FICON Configuration Files
The configuration file submode allows you to create and edit FICON configuration files. If a specified file does not exist, it is created. Up to 16 files can be saved. Each file name is restricted to eight alphanumeric characters.
![]() Note |
To view the latest FICON information, you must click the Refresh button. See the Automatically Saving the Running Configuration. |
To edit the contents of a specified FICON configuration file using Device Manager, follow these steps:
Procedure
Step 1 |
Choose FICON > VSANs . |
Step 2 |
Click the Files tab. You see the FICON VSANs dialog box. |
Step 3 |
Select a VSAN ID and then click Open to edit the FICON configuration file. |
Step 4 |
Select a VSAN ID and then click Delete to delete the FICON configuration file. |
Step 5 |
Click Apply to apply the changed FICON configuration file. |
Copying FICON Configuration Files
To copy an existing FICON configuration file using Device Manager, follow these steps:
Procedure
Step 1 |
Choose FICON > VSANs . |
Step 2 |
Click the Files tab. You see the FICON VSANs dialog box. |
Step 3 |
Click Create to create a FICON configuration file. You see the Create FICON VSANs Files dialog box.
|
Step 4 |
Click Copy to copy the file to a new file. |
Step 5 |
Click Apply to apply the FICON configuration file. |
Swapping Ports
To swap ports using Device Manager, follow these steps:
Procedure
Step 1 |
Select two Fibre Channel ports by holding down the CTRL key and clicking them. |
Step 2 |
Choose FICON > Swap Selected Ports. |
Configuring FICON Tape Acceleration
To configure FICON tape acceleration over FCIP, follow these steps:
Procedure
Step 1 |
Expand ISL and then select FCIP in the Physical Attributes pane. |
Step 2 |
Click the Tunnels tab in the Information pane. You see a list of available switches. |
Step 3 |
Click the Create Row icon to create an FCIP tunnel. You see the Create FCIP Tunnel dialog box. |
Step 4 |
Configure the tunnel with the options. |
Step 5 |
Check the TapeAccelerator check box to enable FICON tape acceleration over this FCIP tunnel. |
Step 6 |
Click Create . |
Configuring FICON Tape Read Acceleration
All the configuration guidelines and restrictions applicable for FICON tape acceleration are also applicable for FICON tape read acceleration. Both FICON tape acceleration and FICON tape read acceleration can coexist.
Configuring XRC Acceleration
IBM z/OS Global Mirror eXtended Remote Copy (XRC) is supported on the MSM-18+4 modules. For XRC to function, XRC acceleration must be enabled on the FCIP tunnel interfaces on both ends. XRC acceleration is disabled by default.
XRC acceleration and FICON tape acceleration cannot be enabled on the same FCIP tunnel interface and cannot exist in the same VSAN.
Configure XRC Acceleration
To configure XRC acceleration on a FCIP tunnel interface, follow these steps:
Procedure
Step 1 |
Expand ISL and then select FCIP in the Physical Attributes pane. |
Step 2 |
Click the Tunnels(Advanced) tab in the Information pane. You see a list of available FCIP interfaces. |
Step 3 |
Check the check box in the XRC Emulator column to enable XRC acceleration over the FCIP tunnel. |
Step 4 |
Click Apply . |
Configure XRC acceleration on an FCIP Tunnel Interface Using Device Manager
To configure XRC acceleration on an FCIP tunnel interface using Device Manager, follow these steps:
Procedure
Step 1 |
In the Device Manager window, click IP and then select FCIP from the menu. |
Step 2 |
Click the Tunnels(Advanced) tab in the Information pane. You see a list of FCIP interfaces. |
Step 3 |
Check the check box in the XRC Emulator column to enable XRC acceleration over the FCIP tunnel. |
Step 4 |
Click Apply . |
Place the CUP in a Zone
To place the CUP in a zone, follow these steps:
Procedure
Step 1 |
In DCNM-SAN, choose Zone > Edit Full Zoneset, and then choose Edit > Edit Default Zone Attributes to set the default zone to permit for the required VSAN. |
||
Step 2 |
In Device Manager, choose FC > Name Server... for the required VSAN and obtain the FICON:CUP WWN.
|
||
Step 3 |
In DCNM-SAN, choose Zone > Edit Full Zoneset and add the FICON:CUP pWWN to the zone database. |
Calculating FICON Flow Load Balance
The FICON Flow Load Balance Calculator allows you to get the best load balancing configuration for your FICON flows. The calculator does not rely on any switch or flow discovery in the fabric. It is available from the DCNM-SAN Tools menu.
To use the FICON Flow Load Balance Calculator, follow these steps:
Procedure
Step 1 |
Choose Tools > Flow Load Balance Calculator. You see the Flow Load Balance Calculator. |
||
Step 2 |
Click Add to enter the source and destination(s) flows. |
||
Step 3 |
Enter source and destination using 2 byte hex (by domain and area IDs).You can copy and paste these IDs, and then edit them if required. |
||
Step 4 |
Enter (or select) the number of ISLs between the two switches (for example, between domain ID 0a and 0b). |
||
Step 5 |
Select a row to remove it and click Remove . |
||
Step 6 |
Select the module for which you are calculating the load balance. |
||
Step 7 |
Click Calculate to show the recommended topology.
|
Receiving FICON Alerts
To receive an alert to indicate any changes in the FICON configuration using Device Manager, follow these steps:
Procedure
Step 1 |
Choose FICON > VSANs . You see the FICON VSANs dialog box. |
Step 2 |
Check the User Alert Mode check box to receive an alert when the FICON configuration changes. |
Step 3 |
Click Apply to apply this change. |
Viewing ESCON Style Ports
To view the available and prohibited ESCON style ports using Device Manager, follow these steps:
Procedure
Step 1 |
Check the ESCON Style check box to see the available and prohibited ESCON style ports. In Figure 1, A stands for available and P stands for prohibited. When the port address is highlighted red, it represents the E/TE port or multiple interfaces. ![]() |
Step 2 |
Click Apply to save the changes. |
Displaying RLIR Information
To view RLIR information using Device Manager, follow these steps:
Procedure
Step 1 |
Choose FICON > RLIR ERL. You see the Show RLIR ERL dialog box. |
Step 2 |
Click Close to close the dialog box. |
Displaying FICON Configuration Files
To open and view configuration files in DCNM-SAN, follow these steps:
Procedure
Step 1 |
Choose FICON > VSAN . You see the FICON configuration table in the Information pane. |
Step 2 |
Click the Files tab. |
Step 3 |
Select the file you want to open. |
Step 4 |
Click Open . |
Displaying XRC Acceleration Statistics
To display XRC acceleration statistics, follow these steps:
Procedure
Step 1 |
Expand ISL and then select FCIP in the Physical Attributes pane. |
Step 2 |
Click the XRC Statistics tab in the Information pane. You see the XRC session statistics. |
Displaying XRC Acceleration Statistics
Procedure
Step 1 |
In the Device Manager window, click IP, and then select FCIP from the menu. |
Step 2 |
Click the XRC Statistics tab in the Information pane. |
Displaying FICON Port Address Information
Procedure
Step 1 |
Choose FICON > VSANs . You see the FICON VSANs dialog box. |
Step 2 |
Select a VSAN ID and click Port Configuration. You see the FICON Port Configuration dialog box. |
Step 3 |
Displaying IPL File Information
To display the IPL file information using Device Manager, follow these steps:
Procedure
Step 1 |
Select VSANs from the FICON menu. |
Step 2 |
Click the Files tab. You see the FICON VSANs dialog box. |
Step 3 |
Select the file that you want to view and click Open. |
Viewing the History Buffer
In the directory history buffer, the Key Counter column displays the 32-bit value maintained by Cisco MDS switches. This value is incremented when any port changes state in that VSAN. The key counter (a 32-bit value) is incremented when a FICON-related configuration is changed. Host programs can increment this value at the start of the channel program and then perform operations on multiple ports. The director history buffer keeps a log of which port address configuration was changed for each key-counter value.
The director history buffer provides a mechanism to determine the change in the port state from the previous time when a value was contained in the key counter.
To view the directory history buffer using Device Manager, follow these steps:
Procedure
Step 1 |
Choose FICON > VSANs . You see the FICON VSANs dialog box. |
Step 2 |
Click the Director History button. You see the history buffer dialog box. |
Step 3 |
Click Close to close the dialog box. |
Field Descriptions for FICON
This section displays the field descriptions for this feature.
FICON VSANs
Field |
Description |
---|---|
VSAN ID |
Uniquely identifies a VSAN within a fabric. |
Host Can Offline SW |
If true, it allows the host to put the system offline. |
Host Can Sync Time |
If true, the host can set the system time. |
Port Control by Host |
If true, the host is allowed to alter FICON Director connectivity parameters. |
Port Control by SNMP |
If true, SNMP manager is allowed to alter FICON director connectivity parameters. |
CUP Name |
The name of the control unit device. |
CUP Enable |
Indicates whether the control unit device is enabled. |
Domain ID |
Specifies the domain ID of the switch. |
CodePage |
The Code Page used in this VSAN. |
Character Set |
Character set for the code page used in this VSAN. |
Active=Saved |
If true, the active to saved mode is enabled. All changes will be saved to NVRAM. |
User Alert Mode |
If true, FICON management stations will prompt on changes. |
Device Allegiance |
If CUP is in allegiance state with a channel, it cannot accept any commands from any logical paths. A CUP goes in an allegiance state when it accepts command from a channel and forms an allegiance with it until the successful completion of the channel program, at which point the CUP goes in an unlocked mode. |
VSAN Time |
The system time in the VSAN. This could be set either by the host or be the default global time in the FICON Director. The default global time is the local time in the FICON Director. |
VSAN State |
Controls the state of the ports belonging to a VSAN in the context of the FICON functionality. |
VSAN Serial Number |
The serial number of the FICON director for this VSAN. |
FICON VSANs Files
Field |
Description |
---|---|
Description |
Configuration file description. |
CUP Name |
The name of the control unit device. |
Status |
Locked indicates no change allowed. Unlocked indicates change allowed. |
LastAccessed |
The time this file was last accessed. |
UserAlertMode |
If true, director user alert mode is enabled. |
Global
Field |
Description |
---|---|
Default Port Prohibited |
Check this option to block the default port. |
FICON Port Attributes
Field |
Description |
---|---|
TypeNumber |
The type number for this FICON Director. |
SerialNumber |
The sequence number assigned to this FICON Director during manufacturing. |
Tag |
This is the identifier of the peer port.
|
FcId |
The fabric Id of the other side port (initiator /target). This will be filled only in the case of Fabric ports. |
Status |
valid—If this information is current. old—If this information is cached. Click Clear Old Attributes to clear the cache. |
Name |
The FICON port name. |
Manufacturer |
The name of the company that manufactured this FICON Director. |
ModelNumber |
The model number for this FICON Director. |
PlantOfMfg |
The plant code that identifies the plant of manufacture of this FICON Director. |
UnitType |
The peer type of the port that this port is communicating. ==Channel - host ==Control Unit - disk == Fabric - ISL |
Alert |
Displays one of the following:
|
FICON Port Configuration
Field |
Description |
---|---|
Show Installed Ports Only |
If true, only physically available ports will be listed in the table. |
ESCON Style |
ESCON Style Port Configuration display is the Port Configuration table in DM displaying the ESCON Style Ports. In the table, A represents the available ports and P represents the prohibited ports. |
Port/ Prohibit |
Enter the FICON address of the port and the prohibited list. (This is an alternative to the table grid.) |
Name |
The port name of this port. |
Block |
If true, this port will be isolated. |
Prohibit Grid |
Click on the grid to add or remove the ability of ports to communicate with each other. |
FICON Port Numbers
Field |
Description |
---|---|
Module |
The number of the module in the chassis. |
Reserved Port Numbers (Physical) |
The reserved port numbers for the module. |
NumPorts |
The number of ports reserved for that module. |
Module Name |
The name of the module. |
Reserved Port Numbers (Logical) |
Chassis slot port numbers. Reserved port numbers for one chassis slot. There can be up to 64 port numbers reserved for each slot in the chassis. |
FICON VSANs Director History
To view the latest FICON information, you must click the Refresh button.
Field |
Description |
---|---|
KeyCounter |
The key counter. |
Ports Address Changed |
The list of ports that have configuration change for a value of KeyCounter. |