Catalyst 4500 Series Switch SW Configuration Guide, Release IOS-XE 3.1.0SG

Configuring Quality of Service

This chapter describes how to configure quality of service (QoS) with either automatic QoS (auto-QoS) commands or standard QoS commands on a switch running Supervisor Engine 7-E. It describes how to specify QoS configuration on different types of interfaces (access, Layer 2 trunk, Layer 3 routed, Etherchannel) as well as VLANs. It also describes how to specify different QoS configurations on different VLANs on a given interface (per-port per-VLAN QoS).

Supervisor Engine 7-E supports a QoS configuration model known as MQC (Modular QoS CLI). Please refer to the appropriate configuration section for the supervisor engine on which QoS will be configured. For more information about MQC, see the "Modular Quality of Service Command-Line Interface" section of the Cisco IOS Quality of Service Solutions Configuration Guide, Release 12.3.

This chapter consists of these sections:

•Overview of QoS on the Catalyst 4500 Series Switch

•Configuring QoS

•Configuring Auto-QoS

Note For complete syntax and usage information for the switch commands used in this chapter, first look at the Cisco Catalyst 4500 Series Switch Command Reference and related publications at this location:

http://www.cisco.com/en/US/products//hw/switches/ps4324/index.html

If the command is not found in the Catalyst 4500 Command Reference, it will be found in the larger Cisco IOS library. Refer to the Cisco IOS Command Reference and related publications at this location:

http://www.cisco.com/en/US/products/ps6350/index.html

Overview of QoS on the Catalyst 4500 Series Switch

Typically, networks operate on a best-effort delivery basis, which means that all traffic has equal priority and an equal chance of being delivered in a timely manner. When congestion occurs, all traffic has an equal chance of being dropped.

QoS selects network traffic (both unicast and multicast), prioritizes it according to its relative importance, and uses congestion avoidance to provide priority-indexed treatment; QoS can also limit the bandwidth used by network traffic. QoS can make network performance more predictable and bandwidth utilization more effective.

This section contains the following subsections:

•Prioritization

•QoS Terminology

•Basic QoS Model

•Classification

•Policing and Marking

•Queueing and Scheduling

•Packet Modification

•Per Port Per VLAN QoS

•Flow-based QoS

Prioritization

QoS implementation is based on the DiffServ architecture. This architecture specifies that each packet is classified upon entry into the network. The classification is carried in the IP packet header, using 6 bits from the deprecated IP type of service (TOS) field to carry the classification (class) information. Classification can also be carried in the Layer 2 frame. These special bits in the Layer 2 frame or a Layer 3 packet are described here and shown in Figure 33-1:

•Prioritization values in Layer 2 frames:

Layer 2 Inter-Switch Link (ISL) frame headers have a 1-byte User field that carries an IEEE 802.1p class of service (CoS) value in the three least-significant bits. On interfaces configured as Layer 2 ISL trunks, all traffic is in ISL frames.

Layer 2 802.1Q frame headers have a 2-byte Tag Control Information field that carries the CoS value in the three most-significant bits, which are called the User Priority bits. On interfaces configured as Layer 2 802.1Q trunks, all traffic is in 802.1Q frames except for traffic in the native VLAN.

Other frame types cannot carry Layer 2 CoS values.

Layer 2 CoS values range from 0 for low priority to 7 for high priority.

•Prioritization bits in Layer 3 packets:

Layer 3 IP packets can carry either an IP precedence value or a Differentiated Services Code Point (DSCP) value. QoS supports the use of either value because DSCP values are backward-compatible with IP precedence values.

IP precedence values range from 0 to 7.

DSCP values range from 0 to 63.

Figure 33-1 QoS Classification Layers in Frames and Packets

All switches and routers across the Internet rely on the class information to provide the same forwarding treatment to packets with the same class information and different treatment to packets with different class information. The class information in the packet can be assigned by end hosts or by switches or routers along the way, based on a configured policy, detailed examination of the packet, or both. Detailed examination of the packet is expected to happen closer to the edge of the network so that the core switches and routers are not overloaded.

Switches and routers along the path can use the class information to limit the amount of resources allocated per traffic class. The behavior of an individual device when handling traffic in the DiffServ architecture is called per-hop behavior. If all devices along a path provide a consistent per-hop behavior, you can construct an end-to-end QoS solution.

Implementing QoS in your network can be a simple or complex task and depends on the QoS features offered by your internetworking devices, the traffic types and patterns in your network, and the granularity of control you need over incoming and outgoing traffic.

QoS Terminology

The following terms are used when discussing QoS features:

•Packets carry traffic at Layer 3.

•Frames carry traffic at Layer 2. Layer 2 frames carry Layer 3 packets.

•Labels are prioritization values carried in Layer 3 packets and Layer 2 frames:

–Layer 2 class of service (CoS) values, which range between zero for low priority and seven for high priority:

Layer 2 Inter-Switch Link (ISL) frame headers have a 1-byte User field that carries an IEEE 802.1p CoS value in the three least significant bits.

Layer 2 802.1Q frame headers have a 2-byte Tag Control Information field that carries the CoS value in the three most significant bits, which are called the User Priority bits.

Other frame types cannot carry Layer 2 CoS values.

Note On interfaces configured as Layer 2 ISL trunks, all traffic is in ISL frames. On interfaces configured as Layer 2 802.1Q trunks, all traffic is in 802.1Q frames except for traffic in the native VLAN.

–Layer 3 IP precedence values—The IP version 4 specification defines the three most significant bits of the 1-byte ToS field as IP precedence. IP precedence values range between zero for low priority and seven for high priority.

–Layer 3 differentiated services code point (DSCP) values—The Internet Engineering Task Force (IETF) has defined the six most significant bits of the 1-byte IP ToS field as the DSCP. The per-hop behavior represented by a particular DSCP value is configurable. DSCP values range between 0 and 63.

Note Layer 3 IP packets can carry either an IP precedence value or a DSCP value. QoS supports the use of either value, since DSCP values are backwards compatible with IP precedence values. See Table 33-1.

•Classification is the selection of traffic to be marked.

•Marking, according to RFC 2475, is the process of setting a Layer 3 DSCP value in a packet; in this publication, the definition of marking is extended to include setting Layer 2 CoS values.

•Policing is limiting bandwidth used by a flow of traffic. Policing can mark or drop traffic.

Basic QoS Model

Figure 33-2 illustrates a high-level flow of Supervisor Engine 7-E QoS function.

Figure 33-2 QoS Packet Processing

The QoS model proceeds as follows:

Step 1 The incoming packet is classified (based on different packet fields, receive port and/or VLAN) to belong to a traffic class.

Step 2 Depending on the traffic class, the packet is rate-limited/policed and its priority is optionally marked (typically at the edge of the network) so that lower priority packets are dropped or marked with lower priority in the packet fields (DSCP and CoS).

Step 3 After the packet has been marked, it is looked up for forwarding. This action obtains the transmit port and VLAN to transmit the packet.

Step 4 The packet is classified in the output direction based on the transmit port and/or VLAN. The classification takes into account any marking of the packet by input QoS.

Step 5 Depending on the output classification, the packet is policed, its priority is optionally (re-)marked, and the transmit queue for the packet is determined depending on the traffic class.

Step 6 The transmit queue state is dynamically monitored via the AQM (Active Queue Management) algorithm and drop threshold configuration to determine whether the packet should be dropped or enqueued for transmission.

Step 7 If eligible for transmission, the packet is enqueued to a transmit queue. The transmit queue is selected based on output QoS classification criteria. The selected queue provides the desired behavior in terms of latency and bandwidth.

Classification

Classification is the process of distinguishing one kind of traffic from another by examining the fields in the packet. Classification is enabled when a QoS policy-map is attached to an interface.

You specify which fields in the frame or packet that you want to use to classify incoming traffic.

For non-IP traffic, you have the following classification options:

•CoS value in the VLAN tag of the incoming frame is used to classify the packet.

•If the frame does not contain a CoS value, the port's default CoS value ("0") is used for the classification.

Perform the classification based on a configured MAC ACL, which examines the fields in the Layer 2 header.

For IP traffic, you have the following classification options:

•IP DSCP or IP Precedence in the incoming packet is used for classification. DSCP values range from 0 to 63.

•Perform the classification based on a configured IP standard or extended ACL, which examines various fields in the IP header.

Classification Based on QoS ACLs

A packet can be classified for QoS using multiple match criteria, and the classification can specify whether the packet should match all of the specified match criteria or at least one of the match criteria. To define a QoS classifier, you can provide the match criteria using the match statements in a class map. In the 'match' statements, you can specify the fields in the packet to match on, or you can use IP standard or IP extended ACLs or MAC ACLs. For more information, see the "Classification Based on Class Maps and Policy Maps" section.

If the class map is configured to match all the match criteria, then a packet must satisfy all the match statements in the class map before the QoS action is taken. The QoS action for the packet is not taken if the packet does not match even one match criterion in the class map.

If the class map is configured to match at least one match criterion, then a packet must satisfy at least one of the match statements in the class map before the QoS action is taken. The QoS action for the packet is not taken if the packet does not match any match criteria in the class map.

Note When you use the IP standard and IP extended ACLs, the permit and deny ACEs in the ACL have a slightly different meaning in the QoS context.

•If a packet encounters (and satisfies) an ACE with a "permit," then the packet "matches" the match criterion in the QoS classification.

•If a packet encounters (and satisfies) an ACE with a "deny," then the packet "does not match" the match criterion in the QoS classification.

•If no match with a permit action is encountered and all the ACEs have been examined, then the packet "does not match" the criterion in the QoS classification.

Note When creating an access list, remember that, by default, the end of the access list contains an implicit deny statement for everything if it did not find a match before reaching the end.

After a traffic class has been defined with the class map, you can create a policy that defines the QoS actions for a traffic class. A policy might contain multiple classes with actions specified for each one of them. A policy might include commands to classify the class as a particular aggregate (for example, assign a DSCP) or rate limit the class. This policy is then attached to a particular port on which it becomes effective.

You implement IP ACLs to classify IP traffic by using the access-list global configuration command.

When a class-map is created with the match-all keyword, you cannot include both IP and MAC ACLs as match criteria.

Classification Based on Class Maps and Policy Maps

A class map is a mechanism that you use to isolate and name a specific traffic flow (or class) from all other traffic. The class map defines the criterion used to match against a specific traffic flow to further classify it; the criteria can include matching the access group defined by the ACL or matching a specific list of DSCP, IP precedence, or L2 CoS values. If you have more than one type of traffic that you want to classify, you can create another class map and use a different name. After a packet is matched against the class-map criteria, you can specify the QoS actions via a policy map.

A policy map specifies the QoS actions for the traffic classes. Actions can include setting a specific CoS, DSCP, or IP precedence value; policing the traffic to a specified rate; specifying the traffic bandwidth limitations; shaping the traffic to a specified rate. Before a policy map can be effective, you must attach it to an interface.

You create a class map by using the class-map global configuration command. When you enter the class-map command, the switch enters the class-map configuration mode. In this mode, you define the match criteria for the traffic by using the match class-map configuration command.

You create and name a policy map by using the policy-map global configuration command. When you enter this command, the switch enters the policy-map configuration mode. In this mode, you specify the actions to take on a specific traffic class by using the set, police, bandwidth, or shape policy-map configuration and policy-map class configuration commands. To make the policy map effective, you attach it to an interface by using the service-policy interface configuration command.

The policy map can also contain commands that define the policer, (the bandwidth limitations of the traffic) and the action to take if the limits are exceeded. For more information, see the "Policing and Marking" section.

A policy map also has these characteristics:

•A policy map can contain up to 254 class statements.

•You can have different classes within a policy map.

Policing and Marking

Policing involves creating a policer that specifies the bandwidth limits for the traffic. Packets that exceed the limits are out of profile or nonconforming. Each policer specifies the action to take for packets that are in or out of profile. These actions, carried out by the marker, include passing through the packet without modification, dropping the packet, or marking down the packet with a new DSCP value that is obtained from the configurable policed-DSCP map. You can configure policer within a policy map with the police command in policy-map class configuration mode. For information on the policed-DSCP map, see the "Queueing and Scheduling" section.

When configuring policing and policers, keep these items in mind:

•On Supervisor Engine 7-E, policers account only for the Layer 2 header length when calculating policer rates. In contrast, shapers account for header length as well as IPG in rate calculations.

•By default, no policers are configured.

•Only the average rate and committed burst parameters are configurable.

•After you configure the policy map and policing actions, attach the policy to an ingress or egress interface by using the service-policy interface configuration command.

•For 2 rate 3 colors (2r3c) policers, if no explicit violation-action is specified, the exceed-action is used as the violate-action.

Queueing and Scheduling

Supervisor Engine 7-E hardware supports 8 transmit queues per port. Once the decision has been made to forward a packet out a port, the output QoS classification determines the transmit queue into which the packet must be enqueued.

Queues are assigned when an output policy attached to a port with one or more queuing related actions for one or more classes of traffic. Because there are only eight queues per port, there are at most eight traffic classes (including class-default, the reserved class) with queuing action(s). Classes of traffic that do not have any queuing action are referred to as non-queuing classes. Non-queuing class traffic use the queue corresponding to class-default.

Active Queue Management

Active queue management (AQM) is the pro-active approach of informing you about congestion before a buffer overflow occurs. AQM is done using Dynamic buffer limiting (DBL). DBL tracks the queue length for each traffic flow in the switch. When the queue length of a flow exceeds its limit, DBL drop packets.

Sharing Link Bandwidth Among Transmit Queues

The eight transmit queues for a transmit port share the available link bandwidth of that transmit port. You can set the link bandwidth to be shared differently among the transmit queues using the
bandwidth command in the policy-map class configuration command in class mode.

With this command, you assign the minimum guaranteed bandwidth for each transmit queue.

By default, all queues are scheduled in a round robin manner.

Strict Priority / Low Latency Queueing

On Supervisor Engine 7-E, you can only configure one transmit queue on a port as strict priority (termed Low Latency Queue, or LLQ).

LLQ provides strict-priority queuing for a traffic class. It enables delay-sensitive data, such as voice, to be sent before packets in other queues. The priority queue is serviced first until it is empty or until it falls under r its shape rate. Only one traffic stream can be destined for the priority queue per class-level policy. You enable the priority queue for a traffic class with the priority policy-map class configuration command in class mode.

Traffic Shaping

Traffic Shaping provides the ability to control the rate of outgoing traffic in order to make sure that the traffic conforms to the maximum rate of transmission contracted for it. Traffic that meets certain profile can be shaped to meet the downstream traffic rate requirements to handle any data rate mismatches.

Each transmit queue can be configured to transmit a maximum rate using the shape command in the policy-map class configuration command in class mode

The configuration allows you to specify the maximum rate of traffic. Any traffic that exceeds the configured shape rate is queued and transmitted at the configured rate. If the burst of traffic exceeds the size of the queue, packets are dropped to maintain transmission at the configured shape rate.

Packet Modification

A packet is classified, policed, and queued to provide QoS. Packet modifications can occur during this process:

•For IP packets, classification involves assigning a DSCP to the packet. However, the packet is not modified at this stage; only an indication of the assigned DSCP is carried along. The reason for this is that QoS classification and ACL lookup occur in parallel, and it is possible that the ACL specifies that the packet should be denied and logged. In this situation, the packet is forwarded with its original DSCP to the CPU, where it is again processed through ACL software.

•For non-IP packets, classification involves assigning an internal DSCP to the packet, but because there is no DSCP in the non-IP packet, no overwrite occurs. Instead, the internal DSCP is used both for queueing and scheduling decisions and for writing the CoS priority value in the tag if the packet is being transmitted on either an ISL or 802.1Q trunk port.

•During policing, IP and non-IP packets can have another DSCP assigned to them (if they are out of profile and the policer specifies a markdown DSCP). Once again, the DSCP in the packet is not modified, but an indication of the marked-down value is carried along. For IP packets, the packet modification occurs at a later stage.

Per Port Per VLAN QoS

Per-port per-VLAN QoS (PVQoS) offers differentiated quality-of-services to individual VLANs on a trunk port. It enables service providers to rate limit individual VLAN-based services on each trunk port to a business or a residence. In an enterprise Voice-over-IP environment, it can be used to rate limit voice VLAN even if an attacker impersonates an IP phone. A per-port per-VLAN service policy can be separately applied to either ingress or egress traffic. For configuration details see "Enabling Per-Port Per-VLAN QoS" section.

Flow-based QoS

Note Before reading this section, you should be familiar with implementing Flexible Netflow (Chapter 32 "Configuring Flexible NetFlow") and QoS implementation in this chapter.

Flow based QoS enables microflow policing and marking capability to dynamically learn traffic flows, It also rate limits each unique flow to an individual rate. Flow based QoS is available on Supervisor Engine 7-E with the built-in NetFlow hardware support. It can be applied to ingress traffic on both switched and routed interfaces with flow masks defined using Flexible Netflow (FNF). It supports up to 100,000 individual flows in hardware and up to 512 unique policer configuration. Flow based QoS is typically used in environments where per-user, granular rate-limiting required. For example, per-flow outbound and inbound traffic rate might differ. Flow based QoS is also referred to as User Based Rate Limiting (UBRL).

A flow is defined as a stream of packets having the same properties as those defined by the key fields in the FNF flow record. A new flow is created when the value of data in packet's key fields is unique with respect to the flow that already exist.

A flow based QoS policy is possesses one or more classmaps matching on a FNF flow record. Such a classmap must be configured as match-all to match all the match criteria specified in the classmap. When a flow based QoS policy is attached to a QoS target, ingress traffic on the target is first classified based on the classification rules specified in the class-map. If the classifier has FNF flow record, the key fields specified in the FNF flow record are applied on the classified traffic to create flows provided the flow does not already exist. The corresponding policy actions (policing and marking) are then applied to these individual flows. Flow-based policers (termed microflow policers) rate limit each unique flow. Flows are dynamically created and inactive flows are periodically aged out.

Flow based QoS policy can be attached to QoS targets such as port (P), vlan (V), per-port-per-vlan (PV), and EtherChannel but only in the ingress direction.

For details on now to enable FNF, refer to the "Applying Flow-based QoS Policy" section.

Configuring QoS

Note HQoS is not supported on Supervisor Engine 7-E.

Topics include:

•MQC-based QoS Configuration

•Platform-supported Classification Criteria and QoS Features

•Platform Hardware Capabilities

•Prerequisites for Applying a QoS Service Policy

•Restrictions for Applying a QoS Service Policy

•Classification

•Policing

•Marking Network Traffic

•Shaping, Sharing (Bandwidth), Priority Queuing, Queue-limiting and DBL

•Enabling Per-Port Per-VLAN QoS

•Applying Flow-based QoS Policy

MQC-based QoS Configuration

Starting with Cisco IOS Release 15.0(1)XO, a switch using Supervisor Engine 7-E employs the MQC model of QoS. To apply QoS, you use the Modular QoS Command-Line Interface (MQC), which is a CLI structure that allows you to complete the following tasks:

•Specify the matching criteria used to define a traffic class.

•Create a traffic policy (policy map). The traffic policy defines the QoS policy actions to be taken for each traffic class.

•Apply the policy actions specified in the policy map to an interface, VLAN, or port and VLAN.

For more information about the MQC, see the "Modular Quality of Service Command-Line Interface" section of the Cisco IOS Quality of Service Solutions Configuration Guide, Release 12.3.

Note The incoming traffic is considered trusted by default. Only when the trusted boundary feature is enabled on an interface can the port enter untrusted mode. In this mode, the switch marks the DSCP value of an IP packet and the CoS value of the VLAN tag on the Ethernet frame as "0".

Platform-supported Classification Criteria and QoS Features

The following table provides a summary of various classification criteria and actions supported on the Supervisor Engine 7-E. For details, refer to the Catalyst 4500 Series Switch Command Reference.

Platform Hardware Capabilities

Prerequisites for Applying a QoS Service Policy

Unlike the Switch QoS model, there is no prerequisite for enabling QoS on various targets. Just the attachment of a service policy enables QoS and detachment of that policy disables QoS on that target.

Restrictions for Applying a QoS Service Policy

Traffic marking can be configured on an interface, a VLAN, or a port and VLAN. An interface can be a Layer 2 access port, a Layer 2 switch trunk, a Layer 3 routed port, or an EtherChannel. A policy is attached to a VLAN using the vlan configuration mode.

Attaching QoS service policy to VLANs and EtherChannel is described in the "Policy Associations" section.

Classification

Supervisor Engine 7-E supports classification of Layer 2, IP, IPv6 packets, and ARP packets marking performed on input can be matched in the output direction. The previous table lists the full set of capabilities. By default, the Supervisor Engine 7-E also supports classification resources sharing.

By default, when the same policy is attached to a port or a VLAN or on per-port per-vlan targets, ACL entries are shared on the Supervisor Engine 7-E. Even though CAM entries are shared, QoS actions is unique on each target.

For example:

    class-map c1

match ip dscp 50

Policy Map p1

    class c1

police rate 1 m burst 200000

If policy-map p1 is applied to interfaces Gig 1/1 and Gig 1/2, 1 CAM entry is used (one ACE that matches IP packets), but 2 policers are allocated (one per target). So, all IP packets with dscp 50 are policed to 1 mbps on interface Gig 1/1 and packets on interface Gig 1/2 are policed to 1 mbps.

Note With Cisco IOS Release 12.2(46)SG, you can issue the match protocol arp command. For details, see the Catalyst 4500 Series Switch Cisco IOS Command Reference.

Classification Statistics

Supervisor 7-E supports only packet based classification statistics.

Supervisor 7-E supports TCAM resource sharing. When a policy-map is applied on multiple targets, the command show policy-map interface displays the aggregate classification statistics, not those specific to an interface.

Note To obtain per interface policy-map stats, you should configure a unique policy-map name on each interface.

When a policy-map is attached to a port-channel member ports, classification statistics are not displayed.

Configuring a Policy Map

You can attach only one policy map to an interface. Policy maps can contain one or more policy-map classes, each with different match criteria and actions.

Configure a separate policy-map class in the policy map for each type of traffic that an interface receives. Put all commands for each type of traffic in the same policy-map class. QoS does not attempt to apply commands from more than one policy-map class to matched traffic.

Creating a Policy Map

To create a policy map, enter this command:

Switch(config)# [no] policy-map policy_name 

Attaching a Policy Map to an Interface

To create a policy map, enter this command:

Switch(config)# interface {vlan vlan_ID | 
{fastethernet | gigabitethernet} 
slot/interface | Port-channel number}

Switch(config-if)# [no] service-policy 
input policy_map_name 

Switch(config-if)# end 

Switch# show policy-map interface {vlan 
vlan_ID | {fastethernet | gigabitethernet} 
slot/interface}

Policing

Supervisor Engine 7-E supports policers in the following operation modes:

•Single Rate Policer Two Color Marker

This kind of policer is configured with just the committed rate (CIR) and normal burst and it has only conform and exceed actions.

This is the only form supported in the Supervisor Engine II-Plus to V-10GE based systems.

•Single Rate Three Color Marker (srTCM) (RFC 2697)

•Two Rate Three Color Marker (trTCM) (RFC 2698)

•Color Blind Mode

Policing accuracy of 0.75% of configured policer rate.

Supervisor Engine 7-E supports 16384 (16 x 1024, 16K) single rate, single burst policers. 16K policers are organized as 8 banks of 2K policers. The policer banks are dynamically assigned (input or output policer bank) by the software depending on the QoS configuration. So, the 16K policers are dynamically partitioned by software as follows:

–0 Input Policers and 16K Output Policers

–2K Input Policers and 14K Output Policers

–4K Input Policers and 12K Output Policers

–6K Input Policers and 10K Output Policers

–8K Input Policers and 8K Output Policers

–10K Input Policers and 6K Output Policers

–12K Input Policers and 4K Output Policers

–14K Input Policers and 2K Output Policers

–16K Input Policers and 0 Output Policers

These numbers represent individual policer entries in the hardware that support a single rate and burst parameter. Based on this, Supervisor Engines 7-E supports the following number of policers:

•16K Single Rate Policer with Single Burst (Two Color Marker)

•8K Single Rate Three Color Marker (srTCM)

•8K Two Rate Three Color Marker (trTCM)

These policers are partitioned between Input and Output in chunks of 2K policer banks. The different types of policers can all co-exist in the system. However, a given type of policer (srTCM, trTCM etc.) is configurable as a block of 128 policers.

Note Two policers are reserved for internal use.

How to Implement Policing

For details on how to implement the policing features on a Catalyst 4500 series switch, refer to the
Cisco IOS documentation at the following link:

http://www.cisco.com/en/US/docs/ios/12_2/qos/configuration/guide/qcfpolsh.html

Platform Restrictions

Platform restrictions include the following:

•Multi-policer actions can be specified (setting CoS and IP DSCP is supported).

•When unconditional marking and policer based marking exists on the same field(cos or dscp or precedence), policer-based marking is preferred.

•If policer based service-policy is attached to both a port and a VLAN, port-based policed is preferred by default. To over-ride a specific VLAN policy on a given port, then you must configure a per-port per-vlan policy.

•You should not delete a port-channel with a per-port, per-VLAN QoS policy.

Workaround: Before deleting the port-channel, do the following:

1. Remove any per-port per-VLAN QoS policies, if any.

2. Remove the VLAN configuration on the port-channel with the no vlan-range command.

Marking Network Traffic

Marking network traffic allows you to set or modify the attributes of traffic (that is, packets) belonging to a specific class or category. When used in conjunction with network traffic classification, marking network traffic is the foundation for enabling many quality of service (QoS) features on your network This module contains conceptual information and the configuration tasks for marking network traffic.

Contents

•"Information About Marking Network Traffic" section

•"Marking Action Drivers" section

•"Traffic Marking Procedure Flowchart" section

•"Restrictions for Marking Network Traffic" section

•"Multi-attribute Marking Support" section

•"Hardware Capabilities for Marking" section

•"Configuring the Policy Map Marking Action" section

•"Marking Statistics" section

Information About Marking Network Traffic

To mark network traffic, you should understand the following concepts:

•"Purpose of Marking Network Traffic" section

•"Benefits of Marking Network Traffic" section

•"Two Methods for Marking Traffic Attributes" section

Purpose of Marking Network Traffic

Traffic marking is used to identify certain traffic types for unique handling, effectively partitioning network traffic into different categories.

After the network traffic is organized into classes by traffic classification, traffic marking allows you to mark (that is, set or change) a value (attribute) for the traffic belonging to a specific class. For instance, you may want to change the class of service (CoS) value from 2 to 1 in one class, or you may want to change the differentiated services code point (DSCP) value from 3 to 2 in another class. In this module, these values are referred to as attributes or marking fields.

Attributes that can be set and modified include the following:

•CoS value of a tagged Ethernet frame

•DSCP/Precedence value in the Type of Service (ToS) byte of IPv4.

•QoS group identifier (ID)

•DSCP /Precedence value in the traffic class byte of IPv6

Benefits of Marking Network Traffic

Traffic marking allows you to fine-tune the attributes for traffic on your network. This increased granularity helps isolate traffic that requires special handling, and thus, helps to achieve optimal application performance.

Traffic marking allows you to determine how traffic will be treated, based on how the attributes for the network traffic are set. It allows you to segment network traffic into multiple priority levels or classes of service based on those attributes, as follows:

•Traffic marking is often used to set the IP precedence or IP DSCP values for traffic entering a network. Networking devices within your network can then use the newly marked IP precedence values to determine how traffic should be treated. For example, voice traffic can be marked with a particular IP precedence or DSCP and strict priority can then be configured to put all packets of that marking into that queue. In this case, the marking was used to identify traffic for strict priority queue.

•Traffic marking can be used to identify traffic for any class-based QoS feature (any feature available in policy map class configuration mode, although some restrictions exist).

•Traffic marking can be used to assign traffic to a QoS group within a switch. The switch can use the QoS groups to determine how to prioritize traffic for transmission. The QoS group value is usually used for one of the two following reasons:

–To leverage a large range of traffic classes. The QoS group value has 64 different individual markings, similar to DSCP.

–If changing the Precedence or DSCP value is undesirable.

Two Methods for Marking Traffic Attributes

Note This section describes Unconditional marking, which differs from Policer-based marking. Unconditional marking is based solely on classification.

Method One: Unconditional Explicit Marking (using the set command)

You specify the traffic attribute you want to change with a set command configured in a policy map. The following table lists the available set commands and the corresponding attribute. For details on the set command, refer to the Catalyst 4500 Series Switch Command Reference.

If you are using individual set commands, those set commands are specified in a policy map. The following is a sample of a policy map configured with one of the set commands listed in Table 33-2.

In this sample configuration, the set cos command has been configured in the policy map (policy1) to mark the CoS attribute:

enable

configure terminal

policy map p1

    class class1

      set cos 3

end

For information on configuring a policy map, see the "Creating a Policy Map" section.

The final task is to attach the policy map to the interface. For information on attaching the policy map to the interface, see the "Attaching a Policy Map to an Interface" section.

Method Two: Unconditional Tablemap-based Marking

You can create a table map that can be used to mark traffic attributes. A table map is a kind of two-way conversion chart that lists and maps one traffic attribute to another. A table map supports a many-to-one type of conversion and mapping scheme. The table map establishes a to-from relationship for the traffic attributes and defines the change to be made to the attribute. That is, an attribute is set to one value that is taken from another value. The values are based on the specific attribute being changed. For instance, the Precedence attribute can be a number from 0 to 7, while the DSCP attribute can be a number from 0 to 63.

The following is a sample table map configuration:

table-map table-map1

map from 0 to 1

map from 2 to 3

exit

The following table lists the traffic attributes for which a to-from relationship can be established using the table map.

The following is an example of a policy map (policy2) configured to use the table map (table-map1) created earlier:

Policy map policy

    class class-default

set cos dscp table table-map

exit

In this example, a mapping relationship was created between the CoS attribute and the DSCP attribute as defined in the table map.

For information on configuring a policy map to use a table map, "Configuring a Policy Map" section.

The final task is to attach the policy map to the interface. For information on attaching the policy map to the interface, see the "Attaching a Policy Map to an Interface" section.

Marking Action Drivers

A marking action can be triggered based on one of the two QoS processing steps.

Classification based: In this case, all the traffic matching a class is marked using either explicit or tablemap based method. This method is referred to as unconditional marking.

Policer result-based: In this case, a class of traffic is marked differently based on the policer result (conform/exceed/violate) applicable to that packet. This method is referred to as conditional marking.

Traffic Marking Procedure Flowchart

Figure 33-3 illustrates the order of the procedures for configuring traffic marking.

Figure 33-3 Traffic marking Procedure Flowchart

Restrictions for Marking Network Traffic

The following restrictions apply to packet marking actions:

•QoS-group can be marked only in the input direction and can only support unconditional explicit marking.

•Only explicit marking is supported for policer-based marking.

Multi-attribute Marking Support

Supervisor Engine 7-E can mark more than one QoS attribute of a packet matching a class of traffic. For example, DSCP, CoS, and QoS-group can all be set together, using either explicit or tablemap-based marking.

Note When using unconditional explicit marking of multiple fields or policer-based multi-field, multi-region (conform/exceed/violate) marking the number of tablemaps that can be setup in TOS or COS marking tables will be less than the maximum supported.

Hardware Capabilities for Marking

Supervisor Engine 7-E provides a 256 entry marking action table where each entry specifies the type of marking actions on COS and DSCP/precedence fields as well as policer action to transmit/markdown/drop a packet. One such table is supported for each direction, input and output. This table is used for both unconditional marking as well as policer-based marking. It can be used to support 256 unique marking actions or 64 unique policer-based actions or a combinations of the two.

For each of the marking fields (COS and DSCP), the Supervisor Engine 7-E provides 512 entry marking tables for each direction. These are similar to mapping tables available on supervisor engines that support the switch QoS model. However, these provide an ability to have multiple unique mapping tables that are setup by the user.

For example, the TOS marking table provides marking of DSCP/Precedence fields and can be used as one of the following:

•8 different tablemaps with each mapping the 64 DSCP or qos-group values to another DSCP

•64 (32) different tablemaps with each one mapping 8 CoS (16 CoS and CFi) values to DSCP in input (output) direction

•a combination of above two types of tablemaps

Similar mappings are available on the 512 entry COS marking table.

Configuring the Policy Map Marking Action

This section describes how to establish unconditional marking action for network traffic.

As a prerequisites, create class map (ipp5) and a policy map. (Refer to the"Configuring a Policy Map" section).

Note On the Supervisor Engine 7-E, the marking action command options have been extended (refer to Table 33-2 andTable 33-3).

Configuring Tablemap-based Unconditional Marking

To configure table-map based unconditional marking, perform this task:

Switch# configure terminal

Switch(config)# table-map name

Switch(config-tablemap)# map from 
from_value to to_value

Switch(config-tablemap)# exit

Switch(config)# policy-map name

Switch(config-p)# class name

Switch(config-p-c)# set cos | dscp | 
prec cos | dscp | prec | qos-group 
[table name]

Switch(config-p-c)# end

Switch# show policy-map name

Switch# show table-map name

The following example shows how to enable marking action using table-map.

Switch(config)# table-map dscp2Cos

Switch(config-tablemap)# map from 8 to 1

Switch(config-tablemap)# exit

Switch(config)# policy-map p1

Switch(config-pmap)# class ipp5

Switch(config-pmap-c)# set cos dscp table dscp2Cos

Switch(config-pmap-c)# end

Switch# show policy-map p1

Policy Map p1

    Class ipp5

      set cos dscp table dscp2Qos

Switch# show table-map dscp2Cos

 Table Map dscp2Cos

    from 8 to 1

    default copy

Configuring Policer Result-based Conditional Marking

To configure policer result-based conditional marking, setup a single rate or dual rate policer. Refer to the "How to Implement Policing" section.

This example shows how to configure a two rate three-color policer with explicit actions for each policer region:

Switch# configure terminal

Switch(config-pmap-c)# policer cir percent 20 pir percent 30

Switch(config-pmap-c-policer)# conform-action set-cos-transmit 3 set-dscp-transmit 10

Switch(config-pmap-c-policer)# exceed-action set-cos-transmit 4 set-dscp-transmit 20

Switch(config-pmap-c-policer)# violate action drop

Switch# show policy-map p1

  Policy Map police

    Class ipp5

     police cir percent 20 pir percent 30

       conform-action set-cos-transmit 3

       conform-action set-dscp-transmit af11

       exceed-action set-cos-transmit 4

       exceed-action set-dscp-transmit af22

       violate-action drop 

Marking Statistics

The marking statistics indicate the number of packets that are marked.

For unconditional marking, the classification entry points to an entry in the marking action table that in turn indicates the fields in the packet that are marked. Therefore, the classification statistics by itself indicates the unconditional marking statistics.

For a conditional marking using policer, provided the policer is a packet rate policer, you cannot determine the number packets marked because the policer only provides byte statistics for different policing results.

Shaping, Sharing (Bandwidth), Priority Queuing, Queue-limiting and DBL

Supervisor Engine 7-E supports the Classification-based (class-based) mode for transmit queue selection. In this mode, the transmit queue selection is based on the Output QoS classification lookup.

Note Only output (egress) queuing is supported.

The Supervisor Engine 7-E hardware supports 8 transmit queues per port. Once the forwarding decision has been made to forward a packet out a port, the output QoS classification determines the transmit queue into which the packet needs to be enqueued.

By default, in Supervisor Engine 7-E, without any service policies associated with a port, there are two queues (a control packet queue and a default queue) with no guarantee as to the bandwidth or kind of prioritization. The only exception is that system generated control packets are enqueued into control packet queue so that control traffic receives some minimum link bandwidth.

Queues are assigned when an output policy attached to a port with one or more queuing related actions for one or more classes of traffic. Because there are only eight queues per port, there can be at most eight classes of traffic (including the reserved class, class-default) with queuing action(s). Classes of traffic that do not have any queuing action are referred to as non-queuing classes. Non-queuing class traffic ends up using the queue corresponding to class class-default.

When a queuing policy (a policy with queuing action) is attached, the control packet queue is deleted and the control packets are enqueued into respective queue per their classification. Note that this differs from the way control-traffic was prioritized in the Catalyst 4924, Catalyst 4948, Catalyst 4948-10GE, and the Supervisor Engines II+, II+10GE, VI, V, and V-10GE. On these platforms, by default, control traffic was guaranteed 25 per cent of the link bandwidth whether QoS was configured. If this same behavior is required on Supervisor Engine 7-E, an egress QoS class must be configured to match
IP Precedence 6 and 7 traffic, and a bandwidth guarantee must be configured.

Dynamic resizing of queues (queue limit class-map action) is supported through the use of the queue-limit command. Based on the chassis and line card type, all eight queues on a port are configured with equal queue size.

Shaping

Shaping enables you to delay out-of-profile packets in queues so that they conform to a specified profile. Shaping is distinct from policing. Policing drops packets that exceed a configured threshold, whereas shaping buffers packets so that traffic remains within a given threshold. Shaping offers greater smoothness in handling traffic than policing. You enable average-rate traffic shaping on a traffic class with the policy-map class configuration command.

Supervisor Engine 7-E supports a range of 32kbps to 10 gbps for shaping, with a precision of approximately +/- 0.75 per cent.

When a queuing class is configured without any explicit shape configuration, the queue shape is set to the link rate.

To configure class-level shaping in a service policy, perform this task:

Switch# configure terminal

Switch(config)# policy-map 
policy-map-name

Switch(config-pmap)# class class-name

Switch(config-pmap-class)# shape 
average {cir-bps [optional_postfix] | 
percent percent}

Switch(config-pmap-class)# exit

Switch(config-pmap)# exit

Switch(config)# interface interface-id

Switch(config-interface)# 
service-policy output policy-map-name

Switch(config-interface)# end 

Switch# show policy-map

[policy-map-name [class 
class-map-name]]

or

Switch# show policy-map interface 
interface-id

Switch# copy running-config 
startup-config 

To delete an existing policy map, use the no policy-map policy-map-name global configuration command. To delete an existing class, use the no class class-name policy-map configuration command. To disable the average-rate traffic shaping, use the no shape average policy-map class configuration command.

This example shows how to configure class-level, average-rate shaping. It limits traffic class class1 to a data transmission rate of 256 kbps:

Switch# configure terminal

Switch(config)# policy-map policy1

Switch(config-pmap)# class class1

Switch(config-pmap-c)# shape average 256000

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Switch(config)# interface gigabitethernet1/1

Switch(config-if)# service-policy output policy1

Switch(config-if)# end

Switch#

Switch# show policy-map policy1

  Policy Map policy1

    Class class1

       shape average 256000

This example shows how to configure class-level, average shape percentage to 32% of link bandwidth for queuing-class traffic:

Switch# configure terminal

Switch(config)# policy-map queuing-policy

Switch(config-pmap)# class queuing-class

Switch(config-pmap-c)# shape average percent 32

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Switch(config)# interface gigabitethernet1/1

Switch(config-if)# service-policy output queuing-policy1

Switch(config-if)# end

Switch #

Switch# show policy-map queuing-policy

  Policy Map queuing-policy

    Class queuing-class

       Average Rate Traffic Shaping

       cir 32%

Sharing(bandwidth)

The bandwidth assigned to a class of traffic is the minimum bandwidth that is guaranteed to the class during congestion. Transmit Queue Sharing is the process by which output link bandwidth is shared among multiple queues of a given port.

Supervisor Engine 7-E supports a range of 32 kbps to 10 gbps for sharing, with a precision of approximately +/- 0.75 per cent. The sum of configured bandwidth across all queuing classes should not exceed the link bandwidth.

To configure class-level bandwidth action in a service policy, perform this task:

Switch# configure terminal

Switch(config)# policy-map 
policy-map-name

Switch(config-pmap)# class class-name

Switch(config-pmap-class)# bandwidth 
{bandwidth-kbps | percent percent}

Switch(config-pmap-class)# exit

Switch(config-pmap)# exit

Switch(config)# interface interface-id

Switch(config-interface)# 
service-policy output policy-map-name

Switch(config-interface)# end 

Switch# show policy-map

[policy-map-name [class 
class-map-name]]

or

Switch# show policy-map interface 
interface-id

Switch# copy running-config 
startup-config 

To delete an existing policy map, use the no policy-map policy-map-name global configuration command. To delete an existing class, use the no class class-name policy-map configuration command. To return to the default bandwidth, use the no bandwidth policy-map class configuration command.

This example shows how to create a class-level policy map called policy11 for three classes called prec1, prec2, and prec3. In the policy for these classes, 30 percent of the available bandwidth is assigned to the queue for the first class, 20 percent is assigned to the queue for the second class, and 10 percent is assigned to the queue for the third class.

Switch # configure terminal

Switch(config)# policy-map policy11

Switch(config-pmap)# class prec1

Switch(config-pmap-c)# bandwidth percent 30

Switch(config-pmap-c)# exit

Switch(config-pmap)# class prec2

Switch(config-pmap-c)# bandwidth percent 20

Switch(config-pmap-c)# exit

Switch(config-pmap)# class prec3

Switch(config-pmap-c)# bandwidth percent 10

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Switch(config)# interface gigabitethernet1/1

Switch(config-if)# service-policy output policy11

Switch(config-if)# end

Switch #

Switch# show policy-map policy11

  Policy Map policy11

    Class prec1

      bandwidth percent 30

    Class prec2

      bandwidth percent 20

    Class prec3

      bandwidth percent 10

This example shows how to create a class-level policy map called policy11 for three classes called prec1, prec2, and prec3. In the policy for these classes, 300 mbps of the available bandwidth is assigned to the queue for the first class, 200 mbps is assigned to the queue for the second class, and 100 mbps is assigned to the queue for the third class.

Switch # configure terminal

Switch(config)# policy-map policy11

Switch(config-pmap)# class prec1

Switch(config-pmap-c)# bandwidth 300000

Switch(config-pmap-c)# exit

Switch(config-pmap)# class prec2

Switch(config-pmap-c)# bandwidth 200000

Switch(config-pmap-c)# exit

Switch(config-pmap)# class prec3

Switch(config-pmap-c)# bandwidth 100000

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Switch(config)# interface gigabitethernet1/1

Switch(config-if)# service-policy output policy11

Switch(config-if)# end

Switch #

Switch# show policy-map policy11

  Policy Map policy11

    Class prec1

      bandwidth 300000 (kbps)

    Class prec2

      bandwidth 200000 (kbps)

    Class prec3

      bandwidth 100000 (kbps)

When a queuing class is configured without any explicit share/bandwidth configuration, because the queue is not guaranteed any minimum bandwidth, the hardware queue is programmed to get a share of any unallocated bandwidth on the port as shown in the following example.

If there is no bandwidth remaining for the new queue or if the unallocated bandwidth is not sufficient to meet the minimum configurable rate (32kbps) for all queues which do not have any explicit share/bandwidth configuration, then the policy association is rejected.

For example, if there are two queues as given below

policy-map queue-policy

   class q1

     bandwidth percent 10

   class q2 

     bandwidth percent 20

then the bandwidth allocation for the queues is as follows

q1 = 10%

           q2 = 20%

class-default = 70%

Similarly, when another queuing class (say q3) is added without any explicit bandwidth (say, just a shape command), then the bandwidth allocation is

q1 = 10%

           q2 = 20%

           q3 = min(35%, q3-shape-rate)

class-default = max(35%, (100 - (q1 + q2 + q3 )))

Priority queuing

On Supervisor Engine 7-E only one transmit queue on a port can be configured as strict priority (termed Low Latency Queue, or LLQ).

LLQ provides strict-priority queuing for a traffic class. It enables delay-sensitive data, such as voice, to be sent before packets in other queues. The priority queue is serviced first until it is empty or until it is under its shape rate. Only one traffic stream can be destined for the priority queue per class-level policy. You enable the priority queue for a traffic class with the priority policy-map class configuration command at the class mode.

A LLQ can starve other queues unless it is rate limited. Supervisor Engine 7-E does not support conditional policing where a 2-parameter policer (rate, burst) becomes effective when the queue is congested (based on queue length). However, it supports application of an unconditional policer to rate limit packets enqueued to the strict priority queue.

When a priority queue is configured on one class of a policy map, only bandwidth remaining is accepted on other classes, guaranteeing a minimum bandwidth for other classes from the remaining bandwidth of what is left after using the priority queue. When a priority queue is configured with a policer, then either bandwidth or bandwidth remaining is accepted on other classes.

Note Use bandwidth or bandwidth remaining on all classes. You cannot apply bandwidth on one class and bandwidth remaining on another class within a policy map.

To enable class-level priority queuing in a service policy, follow these steps:

Switch# configure terminal

Switch(config)# policy-map 
policy-map-name

Switch(config-pmap)# class class-name

Switch(config-pmap-class)# priority

Switch(config-pmap-class)# exit

Switch(config-pmap)# exit

Switch(config)# interface interface-id

Switch(config-interface)# 
service-policy output policy-map-name

Switch(config-interface)# end 

Switch# show policy-map

[policy-map-name [class 
class-map-name]]

or

Switch# show policy-map interface 
interface-id

Switch# copy running-config 
startup-config 

To delete an existing policy map, use the no policy-map policy-map-name global configuration command. To delete an existing class, use the no class class-name policy-map configuration command. To disable the priority queue, use the no priority policy-map class configuration command.

This example shows how to configure a class-level policy called policy1. Class 1 is configured as the priority queue, which is serviced first until it is empty.

Switch# configure terminal

Switch(config)# policy-map policy1

Switch(config-pmap)# class class1

Switch(config-pmap-c)# priority

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Switch(config)# interface gigabitethernet1/1

Switch(config-if)# service-policy output policy1

Switch(config-if)# end

Switch #

Switch# show policy-map policy1

  Policy Map policy1

    Class class1

      priority

Queue-limiting

When a class-based queue is instantiated on a physical port, it is set up with a default size. This size represents the number of queue entries in which packets belonging to that class of traffic can be queued. The scheduler moves packets from the queue that are ready for transmission, based on the queue shape, bandwidth, and priority configuration.

The queue-limit provides the maximum number of packets that can be in the queue at any given time. When the queue is full, an attempt to enqueue any further packets results in tail drop. However, if dynamic buffer limiting (DBL) is enabled on the queue, packets get a probabilistic drop based on the DBL algorithm, even when the queue is not full.

The queue-limit command can be configured under a class only when queue scheduling, such as bandwidth, shape, or priority is already configured. The only exception to this requirement is the support of the stand-alone queue-limit command on the class-default class.

Queue Memory

The number of queue entries that can be allocated has to be a multiple of 8 and can range from 16 to 8184. When a class-based queue is instantiated on a physical port, it is given a default number of entries. This default queue size is based on the number of slots in the chassis and the number of front-panel ports in each slot.

Supervisor Engine 7-E has 1M (1,048,576) queue entries of which the system sets aside 100K (102,400) queue entries in a free reserve pool. Of the remaining queue entries, the drop port is provided 8184 entries, 24576 entries for recirculation ports and the CPU ports are assigned 8656 entries. The remaining entries are divided equally among the slots in the chassis. In a redundant chassis the two supervisor slots are treated as one for the purpose of this entries distribution. Within each slot the number of queue entries are equally divided among the front-panel ports present on the line card in that slot.

When the user configuration for queue entries on an interface exceeds its dedicated quota, the system attempts to satisfy the configuration from the free reserve pool. The entries from the free reserve pool are allocated to interfaces on a first-come first-served basis.

Service Policy Association

When a QoS service-policy with queuing actions is configured, but no explicit queue-limit command is attached in the egress direction on a physical interface, each of the class-based queues gets the same number of queue entries from within the dedicated quota for that physical port. When a queue is explicitly given a size using the queue-limit command, the switch tries to allocate all the entries from within the dedicated quota for the interface. If the required number of entries is greater than the dedicated quota for the interface, the switch tries to allocate the entries from the free reserve.

The queue entries associated with a queue always have to be consecutive. This requirement can result in fragmentation of the 512K of the queue entries that are shared across the switch. For example, an interface may not have enough entries for a queue in its dedicated quota and thus have to use the free reserve to set up that queue. In this case, the queue entries from the dedicated quota remain unused because they cannot be shared with any other port or slot.

When the QoS service-policy associated with an interface is removed, any queue entries taken from the free reserve are returned to the free reserve pool. The interface queuing configuration reverts to two queues — class-default and the control-packet queue with default shape, bandwidth, and size. The control-packet queue is set up with size 16 whereas the default queue is set up with the maximum size possible based on the dedicated quota for that interface.

Queue Allocation Failure

The switch might not be able to satisfy the explicit queue size required on one or more queues on an interface because of fragmentation of queue memory or lack of enough free reserve entries. In this scenario, the switch logs an error message to notify you of the failure. The QoS service-policy is left configured on the interface. You can fix the error by removing the QoS service-policy and examining the current usage of the queue entries from the free reserve by other ports on the switch.

To configure class-level queue-limit in a service policy, perform this task:

Switch# configure terminal

Switch(config)# policy-map 
policy-map-name

Switch(config-pmap)# class class-name

Switch(config-pmap-class)# shape 
average {cir-bps [optional_postfix] | 
percent percent}

Switch(config-pmap-class)# queue-limit 
number-of-packets

Switch(config-pmap-class)# exit

Switch(config-pmap)# exit

Switch(config)# interface interface-id

Switch(config-interface)# 
service-policy output policy-map-name

Switch(config-interface)# end 

Switch# show policy-map

[policy-map-name [class 
class-map-name]]

or

Switch# show policy-map interface 
interface-id

Switch# copy running-config 
startup-config 

To remove the explicit queue size use the no queue-limit command under the class in a policy-map.

This example shows how to configure a class-based queue with an explicit queue-limit command. It limits traffic class class1 to a queue of size 4048:

Switch# configure terminal

Switch(config)# policy-map policy1

Switch(config-pmap)# class class1

Switch(config-pmap-c)# shape average 256000

Switch(config-pmap-c)# queue-limit 4048

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Switch(config)# interface gigabitethernet1/1

Switch(config-if)# service-policy output policy1

Switch(config-if)# end

Switch#

Switch# show policy-map policy1

  Policy Map policy1

    Class class1

       shape average 256000

       queue-limit 4048

Switch#

Active Queue Management (AQM) via Dynamic Buffer Limiting (DBL)

AQM provides buffering control of traffic flows prior to queuing a packet into a transmit queue of a port. This is of significant interest in a shared memory switch, ensuring that certain flows do not hog the switch packet memory.

Note Supervisor Engine 7-E supports active switch buffer management via DBL.

Except for the default class of traffic (class class-default), you can configure DBL action only when at least one of the other queuing action is configured.

To configure class-level dbl action along with shaping in a service policy, perform this task:

Switch# configure terminal

Switch(config)# policy-map 
policy-map-name

Switch(config-pmap)# class class-name

Switch(config-pmap-class)# shape 
average cir-bps

Switch(config-pmap-class)# dbl

Switch(config-pmap-class)# exit

Switch(config-pmap)# exit

Switch(config)# interface interface-id

Switch(config-interface)# 
service-policy output policy-map-name

Switch(config-interface)# end 

Switch# show policy-map

[policy-map-name [class 
class-map-name]]

or

Switch# show policy-map interface 
interface-id

Switch# copy running-config 
startup-config 

To delete an existing policy map, use the no policy-map policy-map-name global configuration command. To delete an existing class, use the no class class-name policy-map configuration command. To disable DBL on the associated queue, use the no dbl policy-map class configuration command.

The following example shows how to configure class-level, DBL action along with average-rate shaping. It enables DBL on the queue associated with traffic-class class1.

Switch# configure terminal

Switch(config)# policy-map policy1

Switch(config-pmap)# class class1

Switch(config-pmap-c)# shape average 256000

Switch(config-pmap-c)# dbl

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Switch(config)# interface gigabitethernet1/1

Switch(config-if)# service-policy output policy1

Switch(config-if)# end

Switch#

Switch# show policy-map policy1

  Policy Map policy1

    Class class1

       shape average 256000

	 dbl

Transmit Queue Statistics

Transmit queue statistics are visible by entering the show policy-map interface command:

Switch# show policy-map interface gigabitEthernet 1/1

 GigabitEthernet1/1

  Service-policy output: queuing-policy

    Class-map: queuing-class (match-all)

      1833956 packets

      Match: cos  1 

      Queueing

      (total drops)  1006239

      (bytes output) 56284756

      shape (average) cir 320000000, bc 1280000, be 1280000

      target shape rate 320000000

    Class-map: class-default (match-any)

      1 packets

      Match: any 

      (total drops)  0

      (bytes output) 2104

Enabling Per-Port Per-VLAN QoS

The per-port per-VLAN QoS feature enables you to specify different QoS configurations on different VLANs on a given interface. Typically, you use this feature on trunk or voice VLANs (Cisco IP Phone) ports, as they belong to multiple VLANs.

To configure per-port per-VLAN QoS, perform this task:

Switch(config)# interface {fastethernet | gigabitethernet | 
tengigabitethernet} slot/interface | Port-channel number 

Switch(config-if)# vlan-range vlan_range

Example 1

Figure 33-4 displays a sample topology for configuring PVQoS. The trunk port gi3/1 is comprised of multiple VLANs (101 and 102). Within a port, you can create your own service policy per VLAN. This policy, performed in hardware, might consist of ingress and egress Policing or giving precedence to voice packet over data.

Figure 33-4 Per-Port Per-VLAN Topology

The following configuration file shows how to perform ingress and egress policing per VLAN using the policy-map P31_QOS applied to port Gigabit Ethernet 3/1:

ip access-list 101 permit ip host 1.2.2.2 any

ip access-list 103 permit ip any any

Class-map match-all RT

 match ip access-group 101

Class-map Match all PD

 match ip access-group 103

Policy-map P31_QoS

 Class RT

  Police 200m 16k conform transmit exceed drop

 Class PD

  Police 100m 16k conform transmit exceed drop

Interface Gigabit 3/1

Switchport

Switchport trunk encapsulation dot1q

Switchport trunk allowed vlan 101-102

Vlan range 101

Service-policy input P31_QoS

Service-policy output P31_QoS

Vlan range 102

Service-policy input P32_QoS

Service-policy output P32_QoS

Example 2

Let us assume that interface Gigabit Ethernet 6/1 is a trunk port and belongs to VLANs 20, 300-301, and 400. The following example shows how to apply policy-map p1 for traffic in VLANs 20 and 400 and policy map p2 to traffic in VLANs 300 through 301:

Switch# configure terminal

Switch(config)# interface gigabitethernet 6/1

Switch(config-if)# vlan-range 20,400

Switch(config-if-vlan-range)# service-policy input p1

Switch(config-if-vlan-range)# exit

Switch(config-if)# vlan-range 300-301

Switch(config-if-vlan-range)# service-policy output p2

Switch(config-if-vlan-range)# end

Switch#

Example 3

The following command shows how to display policy-map statistics on VLAN 20 configured on Gigabit Ethernet interface 6/1:

Switch# show policy-map interface gigabitEthernet 6/1 vlan 20

 GigabitEthernet6/1 vlan 20 

  Service-policy input: p1

    Class-map: c1 (match-all)

      0 packets

      Match: cos  1 

      Match: access-group 100

      police:

          cir 100000000 bps, bc 3125000 bytes

        conformed 0 bytes; actions:

          transmit 

        exceeded 0 bytes; actions:

          drop 

        conformed 0000 bps, exceed 0000 bps

    Class-map: class-default (match-any)

      0 packets

      Match: any

Example 4

The following command shows how to display policy-map statistics on all VLANs configured on Gigabit Ethernet interface 6/1:

Switch# show policy-map interface gigabitEthernet 6/1

 GigabitEthernet6/1 vlan 20 

  Service-policy input: p1

    Class-map: c1 (match-all)

      0 packets

      Match: cos  1 

      Match: access-group 100

      police:

          cir 100000000 bps, bc 3125000 bytes

        conformed 0 bytes; actions:

          transmit 

        exceeded 0 bytes; actions:

          drop 

        conformed 0000 bps, exceed 0000 bps

    Class-map: class-default (match-any)

      0 packets

      Match: any 

 GigabitEthernet6/1 vlan 300 

  Service-policy output: p2

    Class-map: c1 (match-all)

      0 packets

      Match: cos  1 

      Match: access-group 100

      QoS Set

        dscp 50

      police:

          cir 200000000 bps, bc 6250000 bytes

        conformed 0 bytes; actions:

          transmit 

        exceeded 0 bytes; actions:

          drop 

        conformed 0000 bps, exceed 0000 bps

    Class-map: class-default (match-any)

      0 packets

      Match: any 

 GigabitEthernet6/1 vlan 301 

  Service-policy output: p2

    Class-map: c1 (match-all)

      0 packets

      Match: cos  1 

      Match: access-group 100

      QoS Set

        dscp 50

      police:

          cir 200000000 bps, bc 6250000 bytes

        conformed 0 bytes; actions:

          transmit 

        exceeded 0 bytes; actions:

          drop 

        conformed 0000 bps, exceed 0000 bps

Policy Associations

Supervisor Engine 7-E supports per-port, per-VLAN policies. The associated policies are attached to the interface, VLAN, and a specific VLAN on a given port, respectively.

A policy can be associated with a variety of objects. The following table lists the objects and the actions allowed.

Qos Action Restrictions

•The same actions cannot be performed multiple times in a given direction on different targets. In other words, it is not possible to police the packets both on port and VLAN in the input direction. However, the user can police on the input port and on the output VLAN.

•Queuing actions are only allowed in the egress direction and only on the physical port.

•Percentage-based actions like policer cannot be configured on a VLAN, Port and VLAN (PV) and EtherChannel.

•Port channel or VLAN configuration can only have a policing or a marking action, not a queueing action.

Qos Policy priorities

•If a policy on a port and a VLAN are configured with conflicting actions (such as policing or marking actions on both a port and VLAN), the port policy is picked.

•If policy on a VLAN on a given port must be over-written, the user can configure PV policy.

Qos Policy merging

Applicable policies are applied to a given packet in given direction. For example, if you configure egress VLAN-based police and marking, followed by selective queuing on the port, then actions from both policies will be applied for this packet.

The following policy-map configuration restrictions are imposed on an EtherChannel:

•only policing and marking actions are supported at the EtherChannel level

•only queuing actions are supported at the physical member port level

A packet can be marked (dscp or cos fields) by the EtherChannel policy. If the physical member port policy uses a classification based on dscp or cos fields, it must be based on the marked (modified) value. To ensure proper operation, the following restriction is placed on the EtherChannel.

The classification criteria for the policy-map on the physical member ports has to based only on one type of field:

•dscp

•precedence

•cos

•any non marking field (no dscp or cos based classification)

Classification criteria for the policy-map on the physical member ports cannot be based on a combination of fields. This restriction ensures that if the EtherChannel policy is marking down dscp or cos, the marked (modified) value-based classification can be implemented in hardware.

Note Classification criteria for the policy-map on the physical member ports cannot be modified to add a new type of field.

Auto-QoS is not supported on EtherChannel or its member ports. A physical port configured with Auto-QoS is not allowed to become a member of a physical port.

Software QoS

At the highest level, there are two types of locally sourced traffic (such as control protocol packets, pings, and telnets) from the switch: high priority traffic (typically the control protocol packets like OSPF Hellos and STP) and low priority packets (all other packet types).

The QoS treatment for locally-sourced packets differs for the two types.

Supervisor Engine 7-E provides a way to apply QoS to packets processed in the software path. The packets that get this QoS treatment in software can be classified into two types: software switched packets and software generated packets.

On reception, software switched packets are sent to the CPU that in turn sends them out of another interface. For such packets, input software QoS provides input marking and output software QoS provides output marking and queue selection.

The software generated packets are the ones locally sourced by the switch. The type of output software QoS processing applied to these packets is the same as the one applied to software switched packets. The only difference in the two is that the software switched packets take input marking of the packet into account for output classification purpose.

High Priority Packets

High priority packets are marked as one of the following:

•internally with PAK_PRIORITY

•with IP Precedence of 6 (for IP packets)

•with CoS of 6 (for VLAN Tagged packets)

These packets behave as follows:

•They are not dropped because of any policing, AQM, drop thresholds (or any feature that can drop a packet) configured as per the egress service policy. However, they might be dropped because of hardware resource constraints (packet buffers, queue full, etc.).

•They are classified and marked as per the marking configuration of the egress service policy that could be a port or VLAN (refer to the "Policy Associations" section.

•These high priority packets are enqueued to queue on the egress port based on the following criteria:

–If there is no egress queuing policy on the port, the packet is queued to a control packet queue that is setup separately from the default queue and has 5 percent of the link bandwidth reserved for it.

–If there is an egress queuing policy on the port, the queue is selected based on the classification criteria applicable to the packet.

Low Priority Packets

Packets that are not considered high priority (as described previously) are considered unimportant. These include locally sourced pings, telnet, and other protocol packets. They undergo the same treatment as any other packet that is transiting the given transmit port including egress classification, marking and queuing.

Applying Flow-based QoS Policy

Flow based QoS enables microflow policing and marking capability to dynamically learn traffic flows, It also rate limits each unique flow to an individual rate. Flow based QoS is available on Supervisor Engine 7-E with the built-in NetFlow hardware support.

For more overview information, refer to the "Flow-based QoS" section.

The following steps show how to apply Flow based QoS policy to QoS targets:

Step 1 Create a FNF flow record by specifying the key fields that identify unique flows. You can use any FNF flow records that are associated with the FNF monitor.

Step 2 Create a class-map to specify the set of match criteria. Include the FNF flow record from Step 1 in the class-map match criteria using the match flow record command. Then, configure the class-map to match all the match criteria with class-map match-all class_name.

Step 3 Create a policy-map and define actions associated with class-map from Step 2.

Step 4 Attach the policy to one or more QoS targets.

Examples

The following examples illustrate how to configure Flow based QoS policy and apply microflow policers on individual flows.

Example 1

This example assumes there are multiple users (identified by source IP address) on the subnet 192.168.10.*. The configuration below shows how to configure a flow based QoS policy that uses micro policing to limit the per-user traffic with the source address in the range of 192.168.10.*. The microflow policer is configured with a CIR of 1Mbps, "conform action" as transmit, and "exceed action" as drop.

Step 1: Define an ACL to match traffic with specified source address.

Switch(config)# ip access-list extended UserGroup1

Switch(config-ext-nacl)# permit ip 192.168.10.0 0.0.0.255 any

Switch(config-ext-nacl)# exit

Switch(config)#

Step 2: Define a flow record to create flows with source address as key.

Switch(config)# flow record r1

Switch(config-flow-record)# match ipv4 source address

Switch(config-flow-record)# exit

Switch(config)#

Step 3: Configure classmap to match on the UserGroup1 and specify flow record definition for flow creation.

Switch(config)# class-map match-all c1

Switch(config-cmap)# match access-group name UserGroup1

Switch(config-cmap)# match flow record r1

Switch(config-cmap)# exit

Switch(config)#

Step 4: Configure flow based QoS policy-map with microflow policing action for the matching traffic.

Switch(config)# policy-map p1

Switch(config-pmap)# class c1

Switch(config-pmap-c)# police cir 1m

Switch(config-pmap-c-police)# conform-action transmit

Switch(config-pmap-c-police)# exceed-action drop

Switch(config-pmap-c-police)# exit

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Step 5: Attach flow QoS policy to the interface.

Switch(config)# interface gigabitEthernet3/1

Switch(config-if)# service-policy input p1

Switch(config-if)#

Use the show commands (described in the policy and marking sections of this chapter) to display the policy-map configuration and interface specific policy-map statistics.

Example 2.

This example assumes there are multiple users (identified by source IP address) on subnets 192.168.10.* and 172.20.55.*. The first requirement is to police with a CIR of 500Kbps and a PIR of 650Kbps on any TCP traffic originating from 192 network to any destination at any given time. The exceed action keyword marks down the dscp value to 32. The second requirement is to police per-user traffic originating from 172 network to CIR of 2Mbps and unconditionally mark the traffic with dscp 10.

Step 1: Define an ACL to match traffic with specified source address.

Switch(config)# ip access-list extended UserGroup1

Switch(config-ext-nacl)# permit ip 19 2.168.10.0 0.0.0.255 any

Switch(config-ext-nacl)# exit

Switch(config)# ip access-list extended UserGroup2

Switch(config-ext-nacl)# permit ip 172.20.55.0 0.0.0.255 any

Switch(config-ext-nacl)# exit

Switch(config)#

Step 2: Define a flow record to create flows with source address as key.

Switch(config)# flow record r1

Switch(config-flow-record)# match ipv4 source address

Switch(config-flow-record)# match ipv4 destination address

Switch(config-flow-record)# match transport tcp source-port

Switch(config-flow-record)# match transport tcp destination-port

Switch(config-flow-record)# exit

Switch(config)# flow record r2

Switch(config-flow-record)# match ipv4 source address

Switch(config-flow-record)# exit

Switch(config)#

Step 3: Configure classmap to match on the UserGroup1 and specify flow record definition for flow creation.

Switch(config)# class-map match-all c1

Switch(config-cmap)# match access-group name UserGroup1

Switch(config-cmap)# match flow record r1

Switch(config-cmap)# exit

Switch(config)# class-map match-all c2

Switch(config-cmap)# match access-group name UserGroup2

Switch(config-cmap)# match flow record r2

Switch(config-cmap)# exit

Switch(config)#

Step 4: Configure flow based QoS policy-map with microflow policing action for the matching traffic.

Switch(config)# policy-map p1

Switch(config-pmap)# class c1

Switch(config-pmap-c)# police cir 500k pir 650k

Switch(config-pmap-c-police)# conform-action transmit

Switch(config-pmap-c-police)# exceed-action set-dscp-transmit 32

Switch(config-pmap-c-police)# violate-action drop

Switch(config-pmap-c-police)# exit

Switch(config-pmap-c)# exit

Switch(config-pmap)# class c2

Switch(config-pmap-c)# set dscp 10

Switch(config-pmap-c)# police cir 2m

Switch(config-pmap-c-police)# conform-action transmit

Switch(config-pmap-c-police)# exceed-action drop

Switch(config-pmap-c-police)# exit

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Step 5: Attach flow QoS policy to the interface.

Switch(config)# interface gigabitEthernet3/1

Switch(config-if)# service-policy input p1

Switch(config-if)# exit

Use the show commands described in the QoS section to display the policy-map configuration and interface specific policy-map statistics.

Example 3

Assume that there are two active flows on FastEthernet interface 6/1:

With the following configuration, each flow is policed to 1000000 bps with an allowed 9000 burst value.

Switch(config)# flow record r1

Switch(config-flow-record)# match ipv4 source address

Switch(config-flow-record)# match ipv4 destination address

Switch(config-flow-record)# match transport tcp source-port

Switch(config-flow-record)# match transport tcp destination-port

Switch(config-flow-record)# match transport udp source-port

Switch(config-flow-record)# match transport udp destination-port

Switch(config-flow-record)# exit

Switch(config)# class-map match-all c1

Switch(config-cmap)# match flow record r1 

Switch(config-cmap)# exit

Switch(config)# policy-map p1

Switch(config-pmap)# class c1

Switch(config-pmap-c)# police 1000000 9000

Switch(config-pmap-c)# exit

Switch(config-pmap)# exit

Switch(config)# interface fastEthernet 6/1

Switch(config-if)# service-policy input p1

Switch(config-if)# end

Configuration Guidelines

The general guidelines for creating, configuring, modifying, deleting a flow based QoS policy and attaching (and detaching) a flow based QoS policy to a supported target is the same as described in the QoS section. The following description and restriction applies to Flow based QoS policy:

•A classmap can have multiple match statements but only one FNF flow record can be specified in a class-map.

•A flow record must have at least one key field before it can be used in a classmap. Non-key fields can be present in the flow record. However, all the non-key fields are ignored by microflow QoS. Only key-fields are used for flow creation.

•If a FNF flow record is referenced in any class-map, the flow record cannot be modified. Remove the flow record from all classmaps before modifying it.

•A classmap with a FNF flow record must be configured as match-all; traffic hitting the class-map must satisfy all match criteria in the class-map.

•A policy can contain multiple classes and each class-map may contain the same or different FNF flow record.

•Flow based QoS policy and FNF monitor both cannot be applied on the same target at the same time.

•When the interface mode changes from switchport to routed port and vice versa, any Flow QoS policy attached to the port remains applied after the mode change.

•There are 3 types of FNF flow records: ipv4, ipv6, and datalink. The datalink flow record is mutually exclusive with the ipv4 and ipv6 flow records; a classmap with the datalink flow record cannot co-exist with classmap having a ipv4 or ipv6 flow record in the same policy and vice-versa.

•Classmap class-default is not editable; it cannot be configured with the match flow record. Instead, you can configure the policy with a class-map that uses a match any filter and the flow record.

•Traffic is classified in the same order in which class-map is defined in a policy. Hence, if a FNF flow record is the only match statement in a class-map, the classifier matches all packets of the type identified by the flow record. This means that any subsequent class-map in the same policy matching on the same traffic type will be redundant and will never be hit.

•Policers associated with classmap having flow record are called microflow policers. The CIR and PIR rates for microflow policers cannot be configured using the percent keyword.

•Flow records within the same policy must include appropriate key fields to ensure flows created from different classmaps are unique and distinct. Otherwise, the resulting flows from different classmap cannot be distinguished. In such cases, policy actions corresponding to the classmap which created the first flow in hardware will apply and results will not be always be as expected.

•Flows from traffic received on different QoS targets are distinct even if the same policy is applied to those targets.

•A flow is aged out if the it is inactive for more than 5 seconds; there is no traffic matching the flow for a period longer than 5 sec.

•When a flow is aged out, policer state information associated with the flow is also deleted. When a new flow is created, the policer instance for the flow is re-initialized.

•Flows created by flow based QoS policy exist in hardware only and cannot be exported (as with FNF monitor).

•Per-flow statistics are not available for flows created by flow based QoS policy.

•Class-map statistics indicate the number of packets matching the classifier. It does not represent individual flow stats.

•Policer statistics show the aggregate policer statistics of individual flow.

•Information about the flows created by hardware are not available and not displayed in the show commands associated with QoS policy-map. Only class-map and policer statistics are displayed in the output of the show policy-map commands.

Configuring Auto-QoS

Note Auto-QoS cannot be applied to EtherChannel interfaces or VLANs.

Unlike auto-QoS on Supervisor Engines II-Plus to V-10GE, auto-QoS on Supervisor Engine 7-E employs the MQC model. This means that instead of using certain global configurations (like qos and qos dbl), auto-QoS applied to any interface on a switch with Supervisor Engine 7-E configures several global class-maps and policy-maps.

Auto-QoS matches traffic and assigns each matched packet to qos-groups. This allows the output policy map to put specific qos-groups into specific queues, including into the priority queue.

We need QoS in both directions, both on inbound and outbound. Inbound, the switch port needs to trust the DSCP in the packet (done by default). Outbound, the switch port needs to give voice packets "front of line" priority. If voice is delayed too long by waiting behind other packets in the outbound queue, the end host drops the packet because it arrives outside of the receive window for that packet.

Note QoS is a two way street. So, it might work in one direction and not in the other.

There are three policy maps that must be defined (2 inbound and 1 outbound):

•One the trusts COS inbound

•One that trusts DSCP inbound

•A generalized one that puts voice packets in the priority queue outbound

You only want to use the following:

•Trust DSCP policy-map inbound

•General policy-map for voice outbound

On all ports. The problem with COS is that packets on the native VLAN is marked as zero.

The class maps used for input matching are as follows:

! for control traffic between the phone and the callmanager 

! and phone to phone [Bearer] DSCP matching

! Note: Control traffic can be either AF31 or CS3. So, we match to both values and assign 
them to different qos-groups when matching DSCP and only a single group when matching COS.

class-map match-all AutoQos-VoIP-Control-Dscp26

  match  dscp af31

class-map match-all AutoQos-VoIP-Control-Dscp24

  match  dscp cs3

class-map match-all AutoQos-VoIP-Bearer-Dscp

  match  dscp ef

! for control traffic and phone to phone [Bearer] COS matching

! Note: Both CS3 and AF31 control traffic maps to COS 3

class-map match-all AutoQos-VoIP-Control-Cos

  match cos  3

class-map match-all AutoQos-VoIP-Bearer-Cos

  match cos  5

The class maps are intended to identify control and data (bearer) voice traffic for either an Layer 2 or
Layer 3 interface.

The 2 Input policy maps, one for matching DSCP and one for matching COS, where DSCP and COS are set to an assigned qos-group used in outbound policy-maps are as follows:

policy-map AutoQos-VoIP-Input-Dscp-Policy

  class AutoQos-VoIP-Bearer-Dscp

   set qos-group 46

  class AutoQos-VoIP-Control-Dscp26

   set qos-group 26

  class AutoQos-VoIP-Control-Dscp24

   set qos-group 24

! Note: For COS, Control traffic only has a single COS value of 3 (versus DSCP which has 2 
values to match). So, only 2 class-maps instead of 3 like above.

policy-map AutoQos-VoIP-Input-Cos-Policy

  class AutoQos-VoIP-Bearer-Cos

   set qos-group 46

  class AutoQos-VoIP-Control-Cos

   set qos-group 24

The class maps used for Output matching are as follows:

! Since we assigned matched traffic to a qos-group on input, 

! we only need to match the qos-group on output

! Note: Any other traffic not matched on input and assigned to a qos-group goes into the 
class-default queue

! for control traffic (CS3 and AF31)

class-map match-all AutoQos-VoIP-Control-QosGroup24

  match qos-group 24

class-map match-all AutoQos-VoIP-Control-QosGroup26

  match qos-group 26

! For phone to phone (Bearer EF) traffic 

class-map match-all AutoQos-VoIP-Bearer-QosGroup

  match qos-group 46

The output policy maps are as follows:

! Each class maps to a different qos-group with 

! class-default taking any traffic not assigned to a qos-group

! Note: in this example, the outbound policy map drops voice packets when the priority 
queue exceeds 33% utilization of the link. Each deployment must establish their own upper 
bound for voice packets.

policy-map AutoQos-VoIP-Output-Policy

  class AutoQos-VoIP-Bearer-QosGroup

   set dscp ef

   set cos 5

   priority

   police cir percent 33

  class AutoQos-VoIP-Control-QosGroup26

   set dscp af31

   set cos 3

   bandwidth remaining percent 5

  class AutoQos-VoIP-Control-QosGroup24

   set dscp cs3

   set cos 3

   bandwidth remaining percent 5

  class class-default

   dbl

Note There are no default cos-to-dscp or dscp-to-cos mappings on the. Values must be explicitly set for trunks.

The three policy maps are defined as follows:

•policy-map AutoQos-VoIP-Input-Dscp-Policy

This policy map is applied as an input service policy on an Layer 3 interface (such as an uplink connection to a neighboring switch) when auto-QoS is configured on the port.

•policy-map AutoQos-VoIP-Input-Cos-Policy

This policy map is applied as an input service policy on an Layer 2 interface that could be either an uplink connection or a port hooked to a Cisco IP Phone.

•policy-map AutoQos-VoIP-Output-Policy

This policy map is applied as an output policy for any port on which auto-QoS is configured, establishing policy governing egress traffic on the port based on whether it is voice data or control traffic.

The purpose of the input policy maps is to identify voice data or control traffic and mark it as such as it traverses the switch. The output policy map matches the packets on the marking occurring on ingress and then applies egress parameters such as bandwidth, policing and/or priority queuing.

The invocation of auto-QoS on a switch employing Supervisor Engine 7-E uses the same config commands used on Supervisor Engines II-Plus to V-10GE.

For switch-to-switch connections, the [no] auto qos voip trust command is used to apply an input and output service policy on the interface:

service-policy input AutoQos-VoIP-Input-Cos-Policy

OR

service-policy input AutoQos-VoIP-Input-Dscp-Policy

AND

service-policy output AutoQos-VoIP-Output-Policy

The selection of the input policy depends on whether the port is Layer 2 or Layer 3. For Layer 2, the policy trusts the Cos setting in the received packets. For Layer 3 ports, it relies on the DSCP value contained in the packets.

For phone connected ports, the [no] auto qos voice cisco-phone command is used to apply the following service policy to the port:

qos trust device cisco-phone

service-policy input AutoQos-VoIP-Input-Cos-Policy

AND

service-policy output AutoQos-VoIP-Output-Policy

It establishes a trusted boundary that recognizes Cisco IP Phones and trusts the Cos setting of the packets from the phone. If a Cisco IP Phone is not detected, the Cos field is ignored and the packets are not classified as voice traffic. Upon detecting a Cisco phone, the ingress packets are marked based on the Cos value in the packets. This marking is used on egress for proper traffic classification and handling.