The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
| Applicable Product(s) or Functional Area | PCF |
| Applicable Platform(s) | SMI |
| Feature Default Setting | Disabled – Configuration required to enable |
| Related Documentation | Not Applicable |
| Revision Details | Release |
|---|---|
| First introduced. | 2020.01.0 |
PCF supports converged online and offline charging. As part of this support, PCF sends the CHF address to the SMF over the N7 interface. This allows the SMF to connect to the specified CHF for converged online and offline charging. In addition, PCF sends charging-specific attributes (charging decision attributes) in the PCC rules to SMF over the N7 interface.
This section describes how this feature works.
The ability to send CHF addresses in "ChargingInformation" in SM policy create response is added to PCF. In the subsequent SM policy updates, the same address is sent to the SMF. Similarly, the ability to send charging decision attributes in the PCC rules is available in PCF.
The charging information includes primary and secondary CHF addresses. The charging decisions include the following attributes- chgId, meteringMethod, offline, online, ratingGroup, reportingLevel, serviceId, sponsorId, appSvcProvId, and afChargingIdentifier.
 Note |
The charging decisions are supported only for a table-driven PCC and dynamic PCC rules. |
After the SM create control request is received, the PCF reads the charging information service configuration and adds the charging information in the PCF session (if it is not already added).
PCF uses the charging information in the PCF session and sends the ChargingInformation field in "ChgDecs" in response.
After the SM create control request is received, PCF retrieves the PCC rules using "TableDrivenDynamicPccRule" or "DynamicPccRule" service configurations.
The PCC retrieves "ChgIds" (it can either be single chgid value or multiple based on comma separated values) from the "TableDrivenDynamicPccRule" and "ChgID" "from the DynamicPccRule" service configurations.
PCF queries the Charging Data CRD table and retrieves the list of charging data to be sent, after the charging ids are found and "TableDrivenChargingDecisions" is configured.
PCF creates response by adding all charging data under "ChgDecs" and also adds the reference in PCC rules by specifying the "refChgData" array.
This section describes the key call flows for this feature.
This section describes the Online and Offline Charging over N7 to SMF call flow.
This section describes the Creating SM Policy call flow.
|
Step |
Description |
|---|---|
|
1 |
The SMF sends a N7 Create request to the PCF. |
|
2 |
The PCF sends a Load Session request to the CDL. |
|
3 |
The CDL sends a Session Record request to the PCF. |
|
4 |
If the charging information is configured in the service, then PCF populates the PCF session with primary and secondary CHF address. |
|
5 |
The PCF adds the charging information in the response object. |
|
6 |
If the table-driven charging decision is configured in the service, then PCF queries the CRD to retrieve the list of charging decisions. |
|
7 |
The PCF compares the results with the PCF session and identifies the differences. |
|
8 |
The PCF adds charging decisions in the response object. |
|
9 |
The PCF sends a Create Session request to the CDL. |
|
10 |
In response, the CDL sends an acknowledgment to the PCF. |
|
11 |
The PCF sends an N7 Create response to the SMF. |
This section describes the Updating SM Policy call flow.
|
Step |
Description |
|---|---|
|
1 |
The SMF sends an N7 Update request to the PCF. |
|
2 |
The PCF sends a load session by SessionID to the CDL. |
|
3 |
In response, the CDL sends the Session Record to the PCF. |
|
4 |
The PCF resolves the service configuration. |
|
5 |
If the charging information is not available in the PCF session, then PCF populates the session with the primary and secondary CHF address. |
|
6 |
If the charging information is configured in the service, then PCF adds the charging information object in the response object. |
|
7 |
If the table driven charging decision is configured in the service, then PCF queries CRD to retrieve the list of charging decision. |
|
8 |
The PCF compares the result with the PCF session and identifies the delta information. |
|
9 |
The PCF adds the charging decision in the response object. |
|
10 |
The PCF sends the Update Session request to the CDL. |
|
11 |
The CDL acknowledges the update request by sending an acknowledgment to the PCF. |
|
12 |
The PCF sends an N7 Update response to the SMF. |
This section describes the Updating Notify SM Policy call flow.
|
Step |
Description |
|---|---|
|
1 |
The CDL sends a next evaluation timer request to the PCF. |
|
2 |
The PCF sends the Session Record in response to the CDL. |
|
3 |
The PCF resolves the service configuration. |
|
4 |
If the charging information is not available in the PCF session, PCF populates the PCF session with primary and secondary CHF address in the charging information. |
|
5 |
If the charging information is configured in the service, PCF adds the charging information in the response object. |
|
6 |
If the table driven charging decision is configured in the service, PCF queries the CRD to retrieve the list pf charging decisions. |
|
7 |
The PCF compares the results with the PCF session to identify the delta. |
|
8 |
The PCF adds the charging decisions in the response object. |
|
9 |
The PCF sends the Update Session request to the CDL. |
|
10 |
In response, the CDL sends an acknowledgment to the PCF. |
|
11 |
The PCF sends a N7 Notify request to the SMF. |
|
12 |
The SMF sends a N7 Notify response to the PCF. |
ChargingInformation
TableDrivenChargingDecision
This section describes how to configure the ChargingInformation service.
Log in to Policy Builder and navigate to Services tab > Use Case Templates.
Under Actions > Create Child, click Use Case Template, and add ChargingInformation in Service Configuration.
Navigate to Services > Service Option (for that use case template).
Attach the service option to the service.
This section describes how to configure the TableDrivenChargingDecision service.
Log in to Policy Builder and navigate to Custom Reference Data Table, and create a search table group for the charging decision table.
Navigate to Services > Use Case Templates.
Under Actions > Create Child, click Use Case Template, and add TableDrivenChargingDecision in Service Configuration.
Navigate to Services > Service Option (for that use case template).
Attach the Service Option to the service.
Map the source field to Custom Reference Data (CRD) table created in Step 1.
Feedback