Cisco 2.4/5/6 GHz Tri-Band Omnidirectional Antenna (IW-ANT-OMH-2567-N)

Integrated Male N(m)

6 dBi Peak @2400-2482 MHz

8 dBi Peak @4900-4990 MHz

8 dBi Peak @5170-5330 MHz

8 dBi Peak @5490-6875 MHz

IW9167

Cisco 2.4/5/6 GHz Tri-Band Omnidirectional Antenna (IW-ANT-OMV-2567-N)

Integrated Male N(m)

6 dBi Peak @2400-2482 MHz

8 dBi Peak @4900-4990 MHz

8 dBi Peak @5170-5330 MHz

8 dBi Peak @5490-6875 MHz

IW9167

Active GPS antenna, integrated 15' LMR-100 cable with RA-TNC(male).

The ANT-GPS-OUT-TNC integrated GPS RF front end is designed to reject collocated RF interference.

Right-angle TNC male

Active GPS antenna, 4.0 dBi min at Zenith, 1575.42 MHz, plus 25dB amplifier gain

CGR1120 router use case requires ANT-ADPTR-Q-TNC adapter. Router has a QMA(f) GPS connector

LoRaWAN gateways, IXM-LPWA-800-16-K9IXM-LPWA-900-16-K9 directly attached. No adapter needed, as IXM products have TNC(f) GPS connector.

IR510 use case requires LTE-ADPT-SM-TF adapter. IR510 has SMA(f) GPS connector

IR1101 with P-LTE cellular module

C819HG-LTE and C819HG-4G

IR807, IR809, and IR829

All of these use cases require a LTE-ADPT-SM-TF adapter as these routers have a SMA(f) GPS connector.

Instead of a standalone ANT-GPS-OUT-TNC antenna please consider using a multi-element antenna that combines LTE and GPS antennas in a single antenna product such as: ANT-5-4G2WL2G1-O or ANT-3-4G2G1-O

Active GPS antenna that can be physically connected to the Cisco Integrated Services Routers (ISRs) and Cisco Enhanced High-Speed WAN Interface Cards (EHWICs) to receive GPS broadcasts from satellites.

GPS-ACT-ANTM-SMA has GPS filters, but all the filters are after the LNA. Therefore, antenna may not be suitable for co-location with strong RF transmitters.

SMA male

Active GPS antenna, 4 dBi Zenith, 1575.42 MHz, plus 27dB amplifier gain

IR807, IR809, and IR829

IR1101 with P-LTE cellular module

C819HG-LTE and C819HG-4G

indoor/outdoor, active GNSS antenna which can be physically connected to the Cisco Integrated Services Routers (ISRs) and Cisco Industrial Wireless (IW) Access Points and Clients to receive GNSS broadcasts from satellites.

SMA male

Active GPS antenna, 1559 – 1610 MHz, 26 dB, +/- 2 dB Amplifier Gain (LNA Gain)

IW9165E

Cellular 3-in-1 Two port for 2G, 3G, 4G LTE and one port for GPS

Integrated indoor and outdoor Antenna with three ports.

The 4G-LTE-ANTM-O-3-B integrated GPS RF front end is designed to reject collocated RF interference.

SMA-Male

2.5 dBi typical 698-960 MHz

2.5 dBi typical 1710-2700 MHz

One port with GPS element.

IR1101 with P-LTE cellular module

Three port antenna with two elements designed to cover the 698-960, 1448-1511 and 1710-2700 MHz cellular bands and one GPS element.

The ANT-3-4G2G1-O antenna is listed under multiple antenna guide sections due to support of multiple technologies.

The ANT-3-4G2G1-O integrated GPS RF front end is designed to reject collocated RF interference.

Cellular – TNC male

GPS – SMA male

3G/4G

1 dBi zenith, plus 27dB amplifier gain

Active GPS antenna, 1575.42 +/- 5 MHz

IR807, IR809, and IR829IR1101 with P-LTE cellular module

C819HG-LTE and C819HG-4G

CGM-3G and CGM-4G modules with CGR1120 router

CGR1120 use case requires ANT-ADPTR-Q-TNC adapters, as CGR1120 router has a QMA(f) GPS connector, and CGM-3G and CGM-4G modules have QMA(f) cellular connectors

Cisco Multi-element, 5-in-1, 5G (FR1)/LTE/GNSS (ANT-5-5G4G1-O)

4x Cellular (4G/5G) SMA(m)

1x GNSS SMA(m)

4x cellular ports: 617-960/1710-5925 MHz

5G (LTE), Dual Band

Average peak gain:

• 617-960 MHz: 2.0 dBi

• 1710-5925 MHz: 5.8 dBi

To be used with products that support the 5G Pluggable - P-5GS6-GL.

Transportation omnidirectional 5-element antenna for 2G, 3G, 4G cellular, GPS, and dual-band WiFi 2.4 GHz and 5 GHz.

The ANT-5-4G2WL2G1-O integrated GPS RF front end is designed to reject collocated RF interference.

Cellular – TNC male

WLAN - RP-TNC male

GPS – SMA male

3G/4G

4G LTE 698-960, 1448-1511, 1710-2400, 2500-2700 MHz

1 dBi zenith, plus 27dB amplifier gain

Plus 1 port GPS, and 2 ports for dual band WiFi.

1575.42 +/- 1 MHz, GPS L1

Good fit for IR829.

Can be used with other products such as IR809 or IR807, but has extra WiFi elements not required for those products.

Instead consider ANT-3-4G2G1-O for products without WiFi.

Cisco 7-in-1 Vehicle Mount and Fixed Infrastructure Antenna (ANT-7-5G4WL2G1-O)

Transportation omnidirectional 7-element antenna for 3G, 4G, 5G FR1, GNSS and dual-band Wi-Fi (2.4/5GHz) deployments.

4x 4G/5G, SMA(m)

2x 2.4/5GHz Wi-Fi, RP-SMA(plug)

1x GNSS, SMA(m)

3G/4G/5G FR1

617-960/1710-2340/2400-2800/3300-3800/5100-6000 MHz

Dual-band Wi-Fi (2.4/5GHz)

2400-2480/5100-5950 MHz

GNSS

1560-1605 MHz

IR1800, IR8300

Can be used with products like IR1101 but has extra Wi-Fi elements not required for said product.

Consider other multi-element antennas with corresponding adapters/extension cables

Cisco Multi-element, 9-in-1, LTE/Wi-Fi/GNSS antenna (5G-ANTM-O-4-B)

Transportation omnidirectional 9-element antenna for 3G, 4G, 5G FR1, GNSS and dual-band Wi-Fi (2.4/5GHz) deployments.

4x 4G/5G, SMA(m)

4x 2.4/5GHz Wi-Fi, RP-SMA(plug)

1x GNSS, SMA(m)

3G/4G/5G FR1

617-960/1710-2340/2400-2800/3300-3800/5100-6000 MHz

Dual-band Wi-Fi (2.4/5GHz)

2400-2480/5100-5950 MHz

GNSS

1560-1605 MHz

IR1800, IR8300

Can be used with products like IR1101 but has extra Wi-Fi elements not required for said product.

Consider other multi-element antennas with corresponding adapters/extension cables

5 dBi Outdoor Omni-directional Antenna for the Cisco WPAN, LoRaWan, ISM modules and routers.

Type N Female

5.2 dBi 860-876 MHz

5.3 dBi 902-928 MHz

IR509, IR510, IR529, and IR530

WPAN CGM-WPAN-FSK-NA and CGM-WPAN-OFDM-FCC modules in CGR1240 and CGR1120

LoRaWAN gateways, IXM-LPWA-800-16-K9 IXM-LPWA-900-16-K9

Omnidirectional, vertically polarized single-port antenna designed to cover the 860-928 MHz frequency bands for worldwide ISM operation.

Type N male

WPAN 860-928 MHz.

1.5 dBi max

IR509, IR510, IR529, and IR530

WPAN CGM-WPAN-FSK-NA and CGM-WPAN-OFDM-FCC modules in CGR1240 and CGR1120

Vandal Resistant Omni-directional Dome Antenna for ISM, WPAN and LoRaWAN routers.

QMA (male), right angle

1.5-2.0 dBi typical 860-928 MHz

IR509 and IR510

Directional, linearly polarized, mast mount Yagi antenna with a pigtail with N female connector.

18” RG8 pigtail with N female connector

WPAN 860-928 MHz.

9 dBi typical, 10 dBi max

Advanced Range Extenders only. IR529UBWP-915D/K9 and IR529UWP-915D/K9 only.

For 4G cellular use you need the ANT-MP2-I-O-SS-M antenna kit. The kit has qty 2 antennas and cables needed for Main and Aux cellular ports.

ANT-MP2-I-OUT-M is for 915 MHz WPAN, and only has a single antenna and cable in the kit.

Designed for direct mounting on the CGR1240 and has an MCX connector.

MCX jack

0.9 dBi typical, 2.8 dBi max, 860-928 MHz

CGR1240

Connected Grid Modules

ANT-MP2-I-OUT-M kit is compatible with CGM WPAN modules for use with CGR1240 chassis.

The antennas are not mechanically compatible with the CGR1120 chassis.

2-Element Patch Array designed for outdoor use with Cisco Industrial Wireless Access Points.

Type N Male

WiFi 2.4 Ghz

13 dBi

IW3702 in FlexPort mode only

IW3702 use case requires N-type cables.

Supported on the IR829GW family, not recommended for the IR829-2LTE as the antenna is single band.

IR829 use case requires cables and adapters.

IW-6300, ESW-6300

IW/ESW-6300 must be configured in single band mode. Requires N-type cables.

Omnidirectional antenna designed for outdoor use.

Type N Male

WiFi 2.4 GHz

8 dBi

IW-6300, ESW-6300

IW/ESW-6300 must be configured in single band mode.

2-Port Directional antenna with N-type connectors designed for use in outdoor environments.

Type N Male

Wi-Fi 5 GHz

13 dBi

IW3702 in FlexPort mode only

IW3702 use case requires N-type cables.

Supported on the IR829GW family, not recommended for the IR829-2LTE as the antenna is single band.

IR829 use case requires cables and adapters.

IW-6300, ESW-6300

IW/ESW-6300 must be configured in single band mode. Requires N-type cables.

Omnidirectional antenna designed for outdoor use.

Type N Male

Wi-Fi 5 GHz

8 dBi

IW-6300, ESW-6300

IW/ESW-6300 must be configured in single band mode

Dual Port, Dual Band Outdoor Vehicle Mount and Fixed Infrastructure WLAN Antenna, omnidirectional, vertically polarized, 2x2 MIMO, integrated 3 foot long LMR-240 cables with RP-TNC plug connectors.

2 x 3 foot LMR-240 cables with RP-TNC(plug) connectors

Wi-Fi 2.4/5 GHz

4.0 dBi typical, 5.1 dBi max 2400-2500 MHz

6.5 dBi typical, 7.0 dBi max 4900-5875 MHz

IR829

Four-port polarization-diverse patch array with an articulating mount for use on flat surfaces and masts, and is adjustable in both the horizontal and vertical planes. Designed for use in indoor and outdoor environments.

Type N-Female Bulkhead

Wi-Fi 2.4/5 GHz

13 dBi

IW3702, IW-6300, ESW-6300

Requires N-type cables

Four-element, dual-band antenna designed for ceiling-mounting in an indoor environment.

RP-TNC

Wi-Fi

2.4 GHz band: 2 dBi

5 GHz band: 4 dBi

IW3702

IW3702 use case requires AIR-ACC370-NM-RF coaxial adapters

Four port dual-band wall-mounted omnidirectional antenna designed for indoor or outdoor use.

RP-TNC

Wi-Fi

2.4 GHz band: 4 dBi

5 GHz band: 4 dBi

IW3702

IW3702 use case requires AIR-ACC370-NM-RF coaxial adapters

Single port dual-band omni-directional antenna designed to directly attach to an outdoor access point or bulkhead N female connector.

Type N-Male

Wi-Fi

4 dBi 2400–2483 MHz

7 dBi 5250–5875 MHz

IW3702, IW-6300, ESW-6300

IR829

IR829 use case requires cables and adapters.

4-Element Patch Antenna designed for indoor and outdoor use.

RP-TNC

Wi-Fi 2.4/5 GHz

6 dBi in both bands

IW3702

IW3702 use case requires AIR-ACC370-NM-RF coaxial adapters

Transportation omnidirectional 5-element antenna for 2G, 3G, 4G cellular, GPS, and dual-band Wi-Fi 2.4 GHz and 5 GHz.

Cellular – TNC male

WLAN - RP-TNC male

GPS – SMA male

3G/4G

2 ports with dual band Wi-Fi 2.4/5 GHz.

1 port GPS, and 2 ports for 700-2700 MHz cellular.

4.8 dBi typical, 5.5 dBi max, 2400-2500 MHz

5.8 dBi typical, 7.0 dBi max, 4900-5875 MHz

IR829

High-performance, dual-band dipole antenna designed for use with Cisco Aironet 2.4 GHz and 5 GHz radio products with dual-band reverse-polarity TNC (RP-TNC) antenna ports.

RP-TNC plug

Wi-Fi 2.4/5GHz

2 dBi 2.4 GHz

4 dBi 5. GHz

IW3702

IW3702 use case requires AIR-ACC370-NM-RF coaxial adapters

Matching antenna color is the white AIR-ANT2524DW-R

IR829

Matching antenna color is the black AIR-ANT2524DB-R

Four port dual-band polarization-diverse directional array antenna. It operates over the 2.4 GHz and 5 GHz Wi-Fi bands. It ships with an articulating mount for use on flat surfaces and masts, and is adjustable in both horizontal and vertical planes.

RP-TNC (with coupling ring)

2.4 GHz and 5 GHz

6 dBi

IW3702

IW3702 use case requires AIR-ACC370-NM-RF coaxial adapters

IR829

Single port dual-band omnidirectional antenna designed to directly attach to an outdoor access point or bulkhead N female connector.

Type N-Male

2.4/5 GHz

6 dBi 2400 – 2483 MHz

8 dBi 5150 – 5925 MHz

IW-6300, ESW-6300

Three port directional patch array with an articulating mount for use on flat surfaces and masts and is adjustable in both the horizontal and vertical planes. Designed for use in indoor and outdoor environments.

Type N-Female Bulkhead

2.4/5 GHz

8 dBi in both bands

IW-6300, ESW-6300

IW/ESW-6300 must be configured in dual-band mode. The middle port of the antenna is unused. Requires N-type cables.

Cisco Indoor, Dipole Antenna, single-port (W-ANTM2050D-RPSMA)

W-ANTM2050D-RPSMA is a high-performance indoor antenna used for WLAN dual-band, 2.4/5GHz, indoor deployments.

W-ANTM2050D-RPSMA antennas have high standalone efficiency, and maintain high efficiency when directly installed on front plate of a small or medium size Cisco router. However, depending on chassis size and a variety of other electromagnetic considerations, installing the antenna directly on the chassis is not always recommended.

1 x RP-SMA(m)

1.5 dBi (max), 2400 – 2482 MHz

3.5 dBi (max), 5100 – 5925 MHz

IR21, IR31, IR1800

Cisco 7-in-1 Vehicle Mount and Fixed Infrastructure Antenna (ANT-7-5G4WL2G1-O)

Transportation omnidirectional 7-element antenna for 3G, 4G, 5G FR1, GNSS and dual-band Wi-Fi (2.4/5GHz) deployments.

4x 4G/5G, SMA(m)

2x 2.4/5GHz Wi-Fi, RP-SMA(plug)

1x GNSS, SMA(m)

3G/4G/5G FR1

617-960/1710-2340/2400-2800/3300-3800/5100-6000 MHz

Dual-band Wi-Fi (2.4/5GHz)

2400-2480/5100-5950 MHz

GNSS

1560-1605 MHz

IR1800, IR8300

Can be used with products like IR1101 but has extra Wi-Fi elements not required for said product.

Consider other multi-element antennas with corresponding adapters/extension cables

Cisco Multi-element, 9-in-1, LTE/Wi-Fi/GNSS antenna (5G-ANTM-O-4-B)

Transportation omnidirectional 9-element antenna for 3G, 4G, 5G FR1, GNSS and dual-band Wi-Fi (2.4/5GHz) deployments.

4x 4G/5G, SMA(m)

4x 2.4/5GHz Wi-Fi, RP-SMA(plug)

1x GNSS, SMA(m)

3G/4G/5G FR1

617-960/1710-2340/2400-2800/3300-3800/5100-6000 MHz

Dual-band Wi-Fi (2.4/5GHz)

2400-2480/5100-5950 MHz

GNSS

1560-1605 MHz

IR1800, IR8300

Can be used with products like IR1101 but has extra Wi-Fi elements not required for said product.

Consider other multi-element antennas with corresponding adapters/extension cables

Used for Point-to-Multipoint, where the installation requires a sector antenna on the AP to support Dual Slant panel antennas on the clients.

2x N-Type Female

4.9 - 5.95 GHz

16.0 dBi (min)

16.5 dBi (typ)

IW9167E

IW9165D

Scalar horn antennas have symmetrical main beam with identical beam width in Vertical and Horizontal plane. These antennas are ideal for coverage of areas with clients close to the installation site, where null zone issues exist. High density AP clusters and radio co-location is made possible due to unique radiation patterns and compact size.

2x N Female Bulkhead Connector

5180 - 6400 MHz

9.6 dBi

IW9167E

IW9165D

Designed for long-lasting operation with outdoor access points. Its rugged design withstands harsh environments, making the antenna ideal for industrial wireless, enterprise, and military applications. The antenna is DC grounded for ESD protection of radio components.

Type N Female

5.1-5.9 GHz

5 dBi

IW9167E

IW9165D

IW9165E

N-Female 1.5

4.9-6.0 GHz

IW9167EH

IW9165E

Design utilizes a linear array, encapsulated in a heavy-duty fiberglass radome with a thick-walled mounting base for reliable, long-term use. This rugged design withstands harsh environments, making the antenna ideal for Industrial Wireless and Military applications. The antennas in this series are DC grounded for ESD protection of radio components.

Type N Female

5.1-5.9 GHz

4 dBi

IW9167E

IW9165D

IW9165E

Small directional, planar, linear polarized antenna for outdoor and indoor applications. Features include:

• Dual-slant +/- 45° for MIMO antenna configuration

• WLAN IEEE 802.11 a/h/p/n

• Rugged design, meets EN 50155 and EN 50125-3 railway standards

• Ingress protection IP66 & IP67

N, jack (female) x2

5150 - 5935 MHz

9 dBi

IW9167E

IW9165E

2-port high gain panel antenna is a directional 2-port array solution deployed in a variety of applications.

Features include the following:

• Compact design

• 2x N(f) ports

• Compatible mounting with IW9165D

• IP66/67 rated

• High port-to-port isolation

2x, N(m)-to-N(m), LMR-240, 3m cables

4900-5925 MHz

15 dBi

IW9165D

IW9165E

Bi-Directional Train Top Antenna antenna with a QMA connector.

The antenna is designed to survive high vibration rail installations, including roof mounting on locomotive and passenger cars.

QMA

4.9-5.9 GHz

10-13 dBi

IW9167E

IW9165E

Directional Train Top Antenna antenna with a QMA connector.

The antenna is designed to survive high vibration rail installations, including roof mounting on locomotive and passenger cars.

QMA

4.9-5.9 GHz

10-13 dBi

IW9167E

IW9165E

Designed for point-to-multipoint connectivity in smart cities (coverage for parking lots, building-to-building connectivity etc), or ports and mines.

2x N-Type Female

4.9 - 6.425 GHz

16 dBi (typ)

IW9167E

IW9165D

Cisco 4G Indoor Ceiling-Mount Omnidirectional Antenna (4G-ANTM-OM-CM).

Designed for indoor use with Cisco 3G cellular Enhanced High-Speed WAN Interface Cards (EHWICs) and is compatible with Cisco 3G cellular products using a threaded Neill-Concelman (TNC) Male connector.

TNC male

1 and 1.5 dBi 700–960 MHz

2 dBi 1448-1511 MHz

1.7 and 3.2 dBi 1700–2200 MHz

3 and 4 dBi 2500–2700 MHz

IR807, IR809, and IR829

IR1101 with P-LTE cellular module

CGM-3G and CGM-4G modules in CGR1120 (with additional adapters & cable accessories)

Cisco 4G/3G Omnidirectional Dipole Antenna (4G-LTE-ANTM-D).

The 4G-LTE-ANTM-D omnidirectional dipole antenna is designed for indoor use with Cisco 4G and Cisco 3G wireless Integrated Services Routers Generation 2 (ISRs G2) and Enhanced High-Speed WAN Interface Cards (EHWICs).

Articulated TNC male connector

4G LTE 698-960, 1710-2170, 2500-2700 MHz.

2 dBi

IR800

CGR 1000

Connected Grid Modules

Cisco Indoor Swivel-mount Dipole Antenna (ANT-4G-DP-IN-TNC).

Indoor Swivel-mount Dipole 3G/4G Antenna supported on the Connected Grid Router 1120 and is designed to support Cellular/PCS/AWS/MDS, WiMAX 2100/2300/2500/2600 and global GSM900/GSM1800/UMTS/LTE2600 bands.

TNC male

4G LTE 698-960, 1710-2400, 2500-2700 MHz

0.5 dBi 698-960 MHz)

2.2 dBi 1710-2700 MHz

IR800

CGR 1000

Connected Grid Modules

Cisco Aironet 6.5-dBi Diversity Patch Antenna (AIR-ANT2465P-R).

(AEOS date 04/30/2019)

Diversity patch antenna designed for use with Cisco Aironet access points and bridges but can be used with any 2.4 GHz Cisco Aironet radio device that utilizes an RP-TNC connector.

RP-TNC

WiFi 2.4G

6.5 dBi

IR829

Vertically and horizontally polarized omnidirectional antennas designed for outdoor use.

Type N Male

Wi-Fi 5 GHz

5 dBi

IW-6300, ESW-6300

IW/ESW-6300 must be configured in single band mode.

Omnidirectional antennas designed for outdoor use with Cisco Aironet Outdoor Access Points.

Type N Male

WiFi 2.4 GHz

5 dBi

Cisco Aironet 1552H, 1552S, 1552WU, IW-6300, ESW-6300.

IW/ESW-6300 must be configured in single band mode.

Outdoor Panel Antenna for WiMAX 1.8, 2.5, and 3.8 GHz.

Outdoor Panel Antenna for WiMAX 1.8, 2.5, and 3.8 GHz

N female (x2)

WiMAX 1.8, 2.5, 3.8 GHz.

16 +/- 1 dBi

CGR 1000

Connected Grid Modules

ANT-WM-INT-OUT-M

(Similar to ANT-MP2-I-O-SS-M, except covering 3.3-3.6 GHz)

MCX jack

3.3-3.8 GHz

N/A

WiMax CGM module only.

Cisco Multiband Panel Outdoor 3G Antenna (ANT-3G-PNL-OUT-N).

Multiband Panel Outdoor 3G antenna designed to cover cellular 3G bands.

Type N female

3G

10 dBi 806-960 MHz

11 dBi 1710-2170 MHz

CGM-3G modules only

Cisco Multi-purpose Integrated Antenna (ANT-MP-INT-OUT-M).

Multi-purpose integrated monopole antenna, chassis-mounted, omnidirectional, includes non-integrated coaxial cable. No cable (option class).

MCX jack

3G

2.8 dBi 806-960 MHz

3.5 dBi 1710-2170 MHz

4 dBi 2300-2700 MHz

CGM-3G only in CGR1240 chassis.

This antenna is not mechanically compatible with CGR1120 chassis

Cisco Outdoor Omni Antenna for 900 MHz WPAN (ANT-WPAN-OM-OUT-N).

Outdoor Omnidirectional Antenna for the 900 MHz WPAN module.

Type N female

WPAN 902-928 MHz only

4 dBi

IR509, IR510, and IR529 as well as WPAN CGM-WPAN-FSK-NA and CGM-WPAN-OFDM-FCC modules in CGR1240 and CGR1120