Bidirectional Forwarding Detection Routing

This chapter describes how to configure threat defense to use the Bidirectional Forwarding Detection (BFD) routing protocol.

About BFD Routing

BFD is a detection protocol designed to provide fast forwarding path failure detection times for all media types, encapsulations, topologies, and routing protocols. BFD operates in a unicast, point-to-point mode on top of any data protocol being forwarded between two systems. Packets are carried in the payload of the encapsulating protocol appropriate for the media and the network.

BFD provides a consistent failure detection method for network administrators in addition to fast forwarding path failure detection. Because the network administrator can use BFD to detect forwarding path failures at a uniform rate, rather than the variable rates for different routing protocol hello mechanisms, network profiling and planning are easier and reconvergence time is consistent and predictable.

Guidelines for BFD Routing

Context Mode Guidelines

BFD is supported on all threat defense platforms. It is supported in multi-instance mode.

Firewall Mode Guidelines

Supported in routed firewall mode and not in transparent mode.

Failover and Cluster Guidelines

  • BFD is not supported on failover interfaces.

  • In clustering, BFD is supported only on the control node.

Routing and Protocol Guidelines

  • OSPFv2, OSPFv3, IS-IS, BGP IPv4, and BGP IPv6 protocol are supported.


    Note

    For optimal routing, do not configure BFD when BGP graceful restart for NSF is configured on the device.

    For BFD support on IS-IS, using FlexConfig CLI configure BFD on IS-IS interfaces (Physical Interfaces, Sub-Interfaces, Port-Channels only): 

    For IPv6
###Flex-config Appended CLI###

router isis
  net 11.1111.0000.0000.0001.00
exit
interface GigabitEthernet x/x
  ipv6 router isis
  isis ipv6 bfd
exit

For IPv4
###Flex-config Appended CLI###

router isis
  net 11.1111.0000.0000.0001.00
exit
interface GigabitEthernet x/x
  isis
  isis bfd
exit

    EIGRP protocol is not supported.

  • BFD for static routes is not supported. You can configure BFD on interfaces that belong only to virtual routers.

  • Only named interfaces are supported.

  • BFD on BVI, VTI, and loopback interfaces are not supported.

Single-hop Guidelines

  • Echo mode is disabled by default. You can enable echo mode on single-hop only.

  • Echo mode is not supported for IPv6.

  • Use only a single-hop template to configure a single-hop policy.

  • Authentication of the single-hop template is optional.

  • You cannot configure multiple BFDs on the same interface.

Multi-hop Guidelines

  • Do not configure the source IP address also as the destination IP address.

  • Source and destination address should have same IP type—IPV4 or IPV6.

  • Only network objects of host or network type are allowed.

  • Use only a multi-hop template to configure a multi-hop policy.

  • Authentication is mandatory for the multi-hop template.

Upgrade Guidelines

When you upgrade to version 7.3 and when the previous version has any FlexConfig BFD policies, the management center displays a warning message during deployment. However, it does not stop the deployment process. After post-upgrade deployment, to manage the BFD policies from the UI ( Device (Edit) > Routing > BFD), you must configure BFD policies in the Device (Edit) > Routing > BFD page and remove the configuration from the FlexConfig policy for the device.

Configure BFD

This section describes how to enable and configure the BFD routing policy on your system.

Procedure

Step 1

Create BFD Template.

Step 2

Configure BFD Policies.

Step 3

Configure BFD support in the BGP neighbor settings; see, Step 12

Configure BFD Policies

You can bind a BFD template to an interface belonging to a virtual router, or to a source and destination address pair.

Before you begin

Procedure

Step 1

From the Devices > Device Management page, edit the virtual-router supported device. Navigate to Routing.

Step 2

From the drop-down list, select the desired virtual router, and then click BFD.

Step 3

To configure a BFD on the interface, click the Single-Hop tab or Multi-Hop tab.

Note

 

For a single-hop policy, the BFD template is configured on an interface; for a multi-hop policy, the BFD template is configured on a source and destination address pair.

Step 4

Click Add. To modify the configured BFD policy, click Edit (edit icon).

Note

 

When you edit the interface mapping with BFD template to replace it with a new BFD template, the management center uses a no command to remove the template mapping from interface and applies the new template to the interface which causes a BFD flap which may also lead to an OSPFv2, OSPFv3, or BGP flap. However, if the BFD intervals are higher, the BFD flap might not occur. Alternatively, to avoid the flapping, you can delete the existing BFD template mapping; deploy the interface, and then add the new BFD template to the interface and deploy the configuration.

Configure Single-Hop BFD Policies

You can configure a single-hop BFD policy only on an interface that is belonging to a virtual router.

Before you begin
Procedure

Step 1

In the Single-Hop tab, click Add or Edit.

Step 2

In the Add BFD Single-Hop dialog box, configure the following:

  1. In the Interface drop-down list, interfaces belonging to virtual routers are listed. Select the interface you want to configure with the BFD policy.

  2. In the Template Name drop-down list, single-hop templates are listed. Select the template that you want to apply.

    If you have not created a single-hop template, use Add (add icon) and create a single-hop BFD template.

Step 3

Click OK and Save the configuration.

Configure Multi-Hop BFD Policies

You can configure multi-hop BFD policy on a source and destination address pair.

Before you begin
Procedure

Step 1

In the Add BFD Multi-Hop dialog box, configure the following:

  1. Click the BFD source address type—IPv4 or IPv6 radio button.

  2. In the Source Address drop-down list, network objects are listed. Select the source address that you want to configure for the BFD policy. You cannot choose any-ipv4 or any-ipv6.

    If you have not created the required network object, use Add (add icon) and create a host/network object.

    Note

     

    The created network object's IP type should match with the selected source IP type.

  3. In the Destination Address drop-down list, network objects are listed. Select the destination address that you want to configure for the BFD. You cannot choose any-ipv4 or any-ipv6.

    If you have not created the required network object, use Add (add icon) and create a host/network object.

    Note

     

    The created network object's IP type should match with the selected source IP type.

    Attention

     

    Do not select the network object that has the same IP address as that of the source address.

  4. In the Template Name drop-down list, multi-hop templates are listed. Select the template that you want to apply on the BFD policy.

    If you have not created a multi-hop template, use Add (add icon) and create a multi-hop BFD template.

Step 2

Click OK and Save the configuration.

The multi-hop map (table view) is displayed on the Multi-Hop tab page.

History for BFD Routing

Feature

Minimum Management Center

Minimum Threat Defense

Details

BFD support for IS-IS

7.4

7.4

You can configure BFD on IS-IS interfaces using FlexConfig CLI.

BFD support for OSPF

7.4

7.4

You can enable BFD on OSPFv2 and OSPFv3 interfaces.

New/modified screens:

  • Configuration > Device Setup > Routing > OSPFv2

  • Configuration > Device Setup > Routing > OSPFv3

BFD configuration

7.4

7.4

In the previous releases, BFD was configurable on threat defense only through FlexConfig. FlexConfig no longer supports BFD configuration. You can now configure BFD policies for threat defense in the management center UI. In threat defense, BFD is supported only on the BGP protocol.

New/modified screens: Devices > Device Management > Routing > BFD.